Search NASA⌕ Search

SEARCH · Search NASA

Results for “reliability data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,477 records · Page 82
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Temperature Rise on Liner Surfaces of Fuel Cell Electric Vehicle Tanks during Fueling Process

Herein, the temperature of the inner tank walls, or plastic liners, of composite pressure tanks in fuel cell electric vehicles during fueling using three‐dimensional computational fluid dynamics (CFD) models is evaluated. The liner materials are limited to 85.0 °C to prevent thermal stress causing material failure that would result in a hydrogen leak. Therefore, the temperature of hydrogen gas must be limited to below 85.0 °C during the fueling process as dictated by the current fueling protocol. However, there are limited experimental or simulation data confirming that the temperature changes do not exceed the threshold. Herein, the liner temperatures with CFD tank models for two sizes of type IV tanks representative of the upper and lower system bounds that are close to the SAE J2601 fueling protocol (36.0 and 244.0 L) are evaluated. First, each model's reliability is validated with experimental data and then analyzed, and the data are used to evaluate the maximum hydrogen and liner temperatures under real‐world fueling conditions. The evaluation shows that the maximum liner surface temperature of each tank model is at least 7 °C lower than that of the hydrogen. Additionally, there is at least 12 °C difference found between the upper limit and actual liner temperatures.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2019

Abstract for CRADA between the National Energy Technology Laboratory and Strategic Power Systems, Inc. (AGMT-0884)

This project will utilize field data, available through the Operational Reliability Analysis Program (ORAP®), to assess the operation of natural gas combined cycle (NGCC) and coal fired plants in cyclic duty. The emphasis will be on Heat Recovery Steam Generator (HRSG) and coal-fired boiler operating conditions and failure experience related to tube failures. The project will be based on high-fidelity data available in ORAP through the collection of near real time process data characterizing the operating environment and dynamic conditions, from start up to shut-down, that affect the HRSG and coal-fired boiler (i.e. the boiler tubes). It is important to understand the operating environment to assess the influence of the cyclic start-stop cycles, time at temperature, and other operating conditions that can be seen in the data, with their possible impact on the life and reparability of the boiler tubes. This knowledge is important to influence/develop a predictive operations and maintenance strategy to improve performance, increase life, and reduce cost.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS2011

Coherent Evaluation of Aerosol Data Products from Multiple Satellite Sensors

Aerosol retrieval from satellite has practically become routine, especially during the last decade. However, there is often disagreement between similar aerosol parameters retrieved from different sensors, thereby leaving users confused as to which sensors to trust for answering important science questions about the distribution, properties, and impacts of aerosols. As long as there is no consensus, and the inconsistencies are not well characterized and understood, there will be no way of developing reliable model inputs and climate data records from satellite aerosol measurements. Fortunately, the Aerosol Robotic Network (AERONET) is providing well-calibrated globally representative ground-based aerosol measurements corresponding to the satellite-retrieved products. Through a recently developed web-based Multi-sensor Aerosol Products Sampling System (MAPSS), we are utilizing the advantages offered by collocated AERONET and satellite products to characterize and evaluate aerosol retrieval from multiple sensors. Indeed, MAPSS and its companion statistical tool AeroStat are facilitating detailed comparative uncertainty analysis of satellite aerosol measurements from Terra-MODIS, Aqua-MODIS, Terra-MISR, Aura-OMI, Parasol-POLDER, and Calipso-CALIOP. In this presentation, we will describe the strategy of the MAPSS system, its potential advantages for the aerosol community, and the preliminary results of an integrated comparative uncertainly analysis of aerosol products from multiple satellite sensors.

Ichoku, Charles↗
DOE OSTI2019

Recommended Nuclear Data for the Production of Selected Therapeutic Radionuclides

Increasing interest in the treatment of human disease by means of targeted radionuclide-based therapies requires an accurate understanding of achievable yields and quantification of realisable degrees of purity. Important studies within a more extensive Coordinated Research Project of the International Atomic Energy Agency (IAEA CRP) have included in-depth assessments and evaluations of all available measured cross-section data for ten nuclear reactions leading to the formation of 131 Cs, 131 Ba, 225 Ac, 225 Ra, 227 Th, 227 Ac, 230 U and 230 Pa for various on-going and proposed therapeutic applications in nuclear medicine. Equivalent studies were also undertaken of possible reactions to produce the 178W /low-spin 178m Ta generator system that has been clinically applied in diagnosis by means of SPECT - these particular cross-section studies and recommendations are included in this paper for completeness. All available measured data have been critically reviewed and assessed to produce statistically consistent datasets. Selected datasets have been fitted by a least-squares method with Padé approximations of variable order to evaluate the production cross sections and corresponding uncertainties. New measurements have been made in some instances, and reported data have been adjusted to accommodate new nuclear decay or monitor reaction data which altered the original reported quantities adversely. Insufficient measured data are available in many cases to permit a reliable evaluation of cross sections, and these instances are discussed. Finally, recommended therapeutic radionuclide production reaction data and their uncertainties are available on the Web page of the IAEA Nuclear Data Section at www-nds.iaea.org/radionuclides/ and also at the IAEA medical portal www-nds.iaea.org/medportal/.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Towards a study protocol: A data-driven workflow to identify error sources in direct ink write mechatronics

Abstract Using Direct Ink Write (DIW) technology in a rapid and large-scale production requires reliable quality control for printed parts. Data streams generated during printing, such as print mechatronics, are massive and diverse which impedes extracting insights. In our study protocol approach, we developed a data-driven workflow to understand the behavior of sensor-measured X- and Y- axes positional errors with process parameters, such as print velocity and velocity control. We uncovered patterns showing that instantaneous changes in the velocity, when the build platform accelerates and decelerates, largely influence the positional errors, especially in the X- axis due to the hardware architecture. Since DIW systems share similar mechatronic inputs and outputs, our study protocol approach is broadly applicable and scalable across multiple systems. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2024

Automated Grain Boundary (GB) Segmentation and Microstructural Analysis in 347H Stainless Steel Using Deep Learning and Multimodal Microscopy

Austenitic 347H stainless steel offers superior mechanical properties and corrosion resistance required for extreme operating conditions such as high temperature. The change in microstructure due to composition and process variations is expected to impact material properties. Identifying microstructural features such as grain boundaries thus becomes an important task in the process-microstructure-properties loop. Applying convolutional neural network (CNN)-based deep learning models is a powerful technique to detect features from material micrographs in an automated manner. In contrast to microstructural classification, supervised CNN models for segmentation tasks require pixel-wise annotation labels. However, manual labeling of the images for the segmentation task poses a major bottleneck for generating training data and labels in a reliable and reproducible way within a reasonable timeframe. Microstructural characterization especially needs to be expedited for faster material discovery by changing alloy compositions. Here, in this study, we attempt to overcome such limitations by utilizing multimodal microscopy to generate labels directly instead of manual labeling. We combine scanning electron microscopy images of 347H stainless steel as training data and electron backscatter diffraction micrographs as pixel-wise labels for grain boundary detection as a semantic segmentation task. The viability of our method is evaluated by considering a set of deep CNN architectures. We demonstrate that despite producing instrumentation drift during data collection between two modes of microscopy, this method performs comparably to similar segmentation tasks that used manual labeling. Additionally, we find that naïve pixel-wise segmentation results in small gaps and missing boundaries in the predicted grain boundary map. By incorporating topological information during model training, the connectivity of the grain boundary network and segmentation performance is improved. Finally, our approach is validated by accurate computation on downstream tasks of predicting the underlying grain morphology distributions which are the ultimate quantities of interest for microstructural characterization.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Real Time Volcanic Cloud Products and Predictions for Aviation Alerts

Volcanic eruptions can inject significant amounts of sulfur dioxide (SO2) and volcanic ash into the atmosphere, posing a substantial risk to aviation safety. Ingesting near-real time and Direct Readout satellite volcanic cloud data is vital for improving reliability of volcanic ash forecasts and mitigating the effects of volcanic eruptions on aviation and the economy. NASA volcanic products from the Ozone Monitoring Insrument (OMI) aboard the Aura satellite have been incorporated into Decision Support Systems of many operational agencies. With the Aura mission approaching its 10th anniversary, there is an urgent need to replace OMI data with those from the next generation operational NASA/NOAA Suomi National Polar Partnership (SNPP) satellite. The data provided from these instruments are being incorporated into forecasting models to provide quantitative ash forecasts for air traffic management. This study demonstrates the feasibility of the volcanic near-real time and Direct Readout data products from the new Ozone Monitoring and Profiling Suite (OMPS) ultraviolet sensor onboard SNPP for monitoring and forecasting volcanic clouds. The transition of NASA data production to our operational partners is outlined. Satellite observations are used to constrain volcanic cloud simulations and improve estimates of eruption parameters, resulting in more accurate forecasts. This is demonstrated for the 2012 eruption of Copahue. Volcanic eruptions are modeled using the Goddard Earth Observing System, Version 5 (GEOS-5) and the Goddard Chemistry Aerosol and Radiation Transport (GOCART) model. A hindcast of the disruptive eruption from Iceland's Eyjafjallajokull is used to estimate aviation re-routing costs using Metron Aviation's ATM Tools.

Volcanic ash↗
DOE OSTI2023

Retractable Sensors for In-Core Use in Material Test Reactors - conf paper

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 - 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on friction drive wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 - 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology's MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Retractable Sensors for In-Core Service in Material Test Reactors

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 - 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on counter-rotating wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 - 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology's MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Retractable Sensors for In-Core Service in Material Test Reactors

Material Test Reactors (MTRs) such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) are used to irradiate nuclear fuels and materials to evaluate their performance after high levels of exposure to a reactor in-core environment. The most critical tests are equipped with instrumentation leads, which allow real-time data collection. However, because of the very harsh environment inside high-power MTR experiments, there are very few sensors that can survive and maintain their calibrated readings for the time periods required to obtain the high neutron doses needed for new fuels and materials qualification. As a result, sometimes sponsoring programs are forced to accept low reliability of sensors, collecting useful data for only part of the experiment duration. The work described herein is based on the observation that MTRs normally run at constant power and the corresponding conditions within reactor experiments typically evolve relatively slowly. Therefore, even one or two measurements per day would provide a complete and representative data set. With this in mind, INL has embarked on a program to develop a mechanism capable of pushing a very small-diameter sensor (typically a thermocouple or optical fiber) into the location to be measured, leave the sensor for roughly 60 seconds to allow it to reach equilibrium and transmit the signal, then pull it up and away from the high neutron flux and high-temperature region. Small-diameter capillary tubes, up to 8 m long, are used to guide the sensors to the appropriate locations. These capillary tubes serve as essentially very deep, thin-walled thermowells. The distance a thermocouple or optical fiber would need to traverse is on the order of 40 – 80 cm. By adopting this infrequent cycling strategy, the thermocouple or optical fiber would spend only a few hours in the high-neutron flux/high-temperature environment over the duration of even the longest irradiation experiment. To date, INL has developed two styles of drive mechanisms. The first is based on counter-rotating wheels which drive the sensors in a manner similar to a small MIG welder. This has the advantage of being able to accommodate a very long insertion length. The second is based on a ball screw drive and has the advantages of positive attachment and being able to move more than one sensor at a time. Both drive mechanisms have been fabricated and tested in a laboratory setting. Both systems can handle hard mineral insulated cable (such as thermocouples) or optical fibers encased in small diameter tube. The sizes tested to date are 1 – 1.6 mm diameter. Work in this area is ongoing with an eye toward demonstration in the Massachusetts Institute of Technology’s MITR reactor, followed by deployment in an ATR irradiation experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1990

Compound estimation procedures in reliability

At NASA, components and subsystems of components in the Space Shuttle and Space Station generally go through a number of redesign stages. While data on failures for various design stages are sometimes available, the classical procedures for evaluating reliability only utilize the failure data on the present design stage of the component or subsystem. Often, few or no failures have been recorded on the present design stage. Previously, Bayesian estimators for the reliability of a single component, conditioned on the failure data for the present design, were developed. These new estimators permit NASA to evaluate the reliability, even when few or no failures have been recorded. Point estimates for the latter evaluation were not possible with the classical procedures. Since different design stages of a component (or subsystem) generally have a good deal in common, the development of new statistical procedures for evaluating the reliability, which consider the entire failure record for all design stages, has great intuitive appeal. A typical subsystem consists of a number of different components and each component has evolved through a number of redesign stages. The present investigations considered compound estimation procedures and related models. Such models permit the statistical consideration of all design stages of each component and thus incorporate all the available failure data to obtain estimates for the reliability of the present version of the component (or subsystem). A number of models were considered to estimate the reliability of a component conditioned on its total failure history from two design stages. It was determined that reliability estimators for the present design stage, conditioned on the complete failure history for two design stages have lower risk than the corresponding estimators conditioned only on the most recent design failure data. Several models were explored and preliminary models involving bivariate Poisson distribution and the Consael Process (a bivariate Poisson process) were developed. Possible short comings of the models are noted. An example is given to illustrate the procedures. These investigations are ongoing with the aim of developing estimators that extend to components (and subsystems) with three or more design stages.

Barnes, Ron↗
DOE OSTI2017

Quantification of Arctic Soil and Permafrost Properties Using Ground-Penetrating Radar and Electrical Resistivity Tomography Datasets

Improving understanding of Arctic ecosystem climate feedback and parameterization of models that simulate freeze-Thaw dynamics require advances in quantifying soil and snow properties. Due to the significant spatiotemporal variability of soil properties and the limited information provided by point-scale measurements (e.g., cores), geophysical methods hold potential for improving soil and permafrost characterization. In this study, we evaluate the use of a ground-penetrating radar (GPR) to estimate thaw layer thickness, snow depth, and ice-wedge characteristics in an ice-wedge-dominated tundra region near Barrow, AK, USA. To this end, we analyze GPR and point-scale measurements collected along several parallel transects at the end of the growing season and the end of frozen season. In addition, we compare the structural information extracted from the GPR data with electrical resistivity tomography (ERT) information about ice-wedge characteristics. Our study generally highlights the value of GPR data collected in the frozen season, when conditions lead to the improved GPR signal-To-noise ratio, facilitate data acquisition, and reduce acquisition-related ecosystem disturbance relative to growing season. We document for the first time that GPR data collected during the frozen season can provide reliable estimates of active layer thickness and geometry of ice wedges. We find that the ice-wedge geometry extracted from GPR data collected during the frozen season is consistent with ERT data, and that GPR data can be used to constrain the ERT inversion. Consistent with recent studies, we also find that GPR data collected during the frozen season can provide good estimates of snow thickness, and that GPR data collected during the growing season can provide reliable estimate thaw depth. As a result, our quantification of the value of the GPR and ERT data collected during growing and frozen seasons paves the way for coupled inversion of the datasets to improve understanding of permafrost variability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study

# 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction Study The 2023 University of Puerto Rico at Mayagüez National Institute for Congestion Reduction (NCIR) Study provided insight into the travel patterns and associated energy consumption of participants. Study results helped researchers identify opportunities for the development of policies that could incentivize the use of alternative modes of travel such as transit and micromobility. Such travel modes reduce congestion by reducing the miles traveled by privately owned vehicles in urban and rural areas. The [National Institute for Congestion Reduction](https://nicr.usf.edu/) provides multimodal congestion reduction strategies through real-world deployments that leverage advances in technology, big data science, and innovative transportation options to optimize the efficiency and reliability of the transportation system for all users. ## Data Collection Agency The University of Puerto Rico at Mayagüez conducted the study. ## Survey Methodology The study was conducted in Spanish. Data collection was enabled via the open-source [NREL OpenPATH platform](https://www.nrel.gov/transportation/openpath). The resulting dataset consists of partially automated travel diaries—combining sensed and surveyed data reflecting patterns of multimodal, end-to-end, individual human mobility—as well as demographic and socioeconomic information from the 17 participants. ## Survey Records, Data, and Documentation Study records include 17 participants. The total number of trips was 458 and total non-air-miles traveled was approximately 1,469.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗