Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Development of a High-Pressure Fuel Injection System for Use with Propane-DME

Paper details the design approach and performance of a high-pressure common rail fuel injection system used with Propane-DME mixtures targeting high injection pressures on a light duty 2.2L inline-4 compression ignition engine. The study estimates the bulk modulus of elasticity based on the hardware geometry and operating pressures to assess the compressibility of Propane and DME across a range of pressures typical of the LD engine application. The compressibility factor ranges from 500 to 3000 bar, significantly lower than the theoretical values for the conditions tested. The high-pressure pump performance is optimized via the implementation of an inlet metering valve operated on a crank-angle open/close sequence to control pressure at the common rail. The application of a model-based controller and the use of high-speed sampling of rail pressure indicate that pressure at the rail can be attained with the pump metering valve, and without use of the pressure relieve valve present in the rail. Results show a significant reduction on pumping work parasitics and of fuel heating, on the order of 40°C, at typical working conditions with the proposed approach. Injector rates of injection with Propane-DME are very similar to those of Diesel. Paper compares bench data of rates of injection versus simulation predictions across operating pressures of 200 to 1000bar and from injection commands spanning 0.20 to 2.0ms. Furthermore, the accuracy of the model predictions are attributed in part by to the updated fuel compressibility modulus descriptions attained during the testing.

42 ENGINEERING↗

Glassy interphases reinforce elastomeric nanocomposites by enhancing percolation-driven volume expansion under strain

For nearly a century, introduction of nanoparticles to elastomers has yielded extraordinarily tough nanocomposites that are critical to technologies from actuators to tires. The mechanisms by which this reinforcement occurs have nevertheless remained a central open question in material science. One widely debated hypothesis posits that strong interactions between polymer and particles induce "glassy bridges" that cement particles into a cohesive percolating network that resists elongation. Here, molecular dynamics simulations show that glassy particle shells do not primarily provide elongational cohesion. Instead, they amplify an underlying mechanism wherein competition between filler and elastomer networks causes the elastomer's volume to increase on deformation. This induces contributions from the elastomer's bulk modulus, which is of order 1000 times larger than its Young's modulus. These findings establish a unified understanding of low-strain reinforcement in filled elastomers as emanating from volumetric competition between coexisting particulate and elastomeric networks. This reframes and unifies our understanding of low-strain reinforcement, provides a clear-cut diagnostic for the presence of glassy bridging, and offers a new design principle for tough elastomeric nanocomposites.

Computational Physics (physics.comp-ph)↗

A comprehensive model of Drosophila epithelium reveals the role of embryo geometry and cell topology in mechanical responses

In order to understand morphogenesis, it is necessary to know the material properties or forces shaping the living tissue. In spite of this need, very few in vivo measurements are currently available. Here, using the early Drosophila embryo as a model, we describe a novel cantilever-based technique which allows for the simultaneous quantification of applied force and tissue displacement in a living embryo. By analyzing data from a series of experiments in which embryonic epithelium is subjected to developmentally relevant perturbations, we conclude that the response to applied force is adiabatic and is dominated by elastic forces and geometric constraints, or system size effects. Crucially, computational modeling of the experimental data indicated that the apical surface of the epithelium must be softer than the basal surface, a result which we confirmed experimentally. Further, we used the combination of experimental data and comprehensive computational model to estimate the elastic modulus of the apical surface and set a lower bound on the elastic modulus of the basal surface. More generally, our investigations revealed important general features that we believe should be more widely addressed when quantitatively modeling tissue mechanics in any system. Specifically, different compartments of the same cell can have very different mechanical properties; when they do, they can contribute differently to different mechanical stimuli and cannot be merely averaged together. Additionally, tissue geometry can play a substantial role in mechanical response, and cannot be neglected.

59 BASIC BIOLOGICAL SCIENCES↗

Compression springs at elevated temperatures

The behavior of compression springs is affected by increased temperatures. The most significant factors affecting springs are a loss of load and length (relaxation), and a change in the modulus of rigidity. Relaxation will reduce preset loads or change the location of supported components whereas a change in the modulus of rigidity will alter the spring rate. Both factors must be taken into account when designing compression springs. Curves and equations are presented (for music wire, 18-8 stainless steel, 17-7 PH, and Inconel-X) which can aid in the design of compression springs for use at elevated temperatures.

Spring↗

Development of cryogenic PRD-49-1 filament-wound tanks

A high modulus polymeric fiber was evaluated as a reinforcement for filament wound pressure vessels. Winding parameters and design data were established for the fiber with two different epoxy resin systems. Comparison was made between the performance factors of the polymeric fiber and those of S-glass and high modulus graphite vessels.

Hoggatt, J. T.↗

An elastic analysis of stresses in a uniaxially loaded sheet containing an interference-fit bolt

The stresses in a sheet with an interference-fit bolt have been calculated for two sheet-bolt interface conditions: a frictionless interface and a fixed (no-slip) interface. The stress distributions were calculated for various combinations of sheet and bolt moduli. The results show that for repeated loading the local stress range is significantly smaller if an interference bolt is used instead of a loosely fitting one. This reduction in local stress range is more pronounced when the ratio of bolt modulus to sheet modulus is large. The analysis also indicates that currently used standard values of interference cause yielding in the sheet.

Crews, J. H., Jr.↗

Factors affecting the thermal shock behavior of yttria stabilized hafnia based graphite and tungsten composites.

Hafnia-based composites containing either graphite or tungsten were investigated as rocket nozzle throat inserts in solid propellant rocket engines. The thermal shock resistance of these materials is considered in terms of macroscopic thermal conductivity, thermal expansion, modulus of elasticity, and compressive fracture stress. The effect of degree of hafnia stabilization, density, and graphite or tungsten content upon these parameters is discussed. The variation of the ratio of elastic modulus to compressive fracture stress with density and its effect upon thermal shock resistance of these materials are discussed in detail.

Lineback, L. D.↗

Nondestructive determination of fatigue crack damage in composites using vibration tests.

The vibration response of glass reinforced epoxy and polyester laminates was investigated. The complex modulus and the damping capacity were measured as fatigue crack damage accumulated. Changes in the Young's modulus as well as the damping capacity correlated with the amount of crack damage. The damping was especially sensitive to debonding of the reinforcement from the resin matrix. Measurement of these vibration response changes shows promise as a means to nondestructively test the structural integrity of filament-reinforced composite structural members.

Dibenedetto, A. T.↗

Stability of a beam on an elastic foundation subjected to a follower force.

Discussion of a new aspect in the behavior of a cantilevered beam on an elastic foundation subjected to a follower force at its free end. The critical load for flutter is found to be independent of the foundation modulus which characterizes the Winkler-type elastic imbedding. The frequency of vibration of the beam increases with increasing foundation modulus, but the magnitude of the critical load is not affected. This result is valid for any 'tangency coefficient' value.

Smith, T. E.↗

A comparative study of tensile fracture mechanisms.

Identification of the failure mechanism characteristic for the more widely used carbon fibers in epoxy matrices under tensile loads as an aid toward improvements and more reliable predictions of the performance of these composites. The presented results pertain to high-strength, high-modulus, and low-modulus fibers in unmodified and modified epoxy novolac matrices.

Mullin, J. V.↗

Monitor for physical property changes in solid propellants

Specially designed sensor is attached to or imbedded in propellant. When sensor is driven into vibration, it moves with a phase lag directly proportional to internal friction or loss coefficent. Resonance frequency of the system is related to Young's modulus. Modulus or internal friction can be monitored over long period of time.

Black, R. E., Jr.↗

Criteria for selecting resin matrices for improved composite strength

Criteria are presented which can be used a priori to select matrices to yield composites with improved unidirectional strength. The criteria evolved from an investigation including both theoretical and experimental efforts. Composite micromechanics were used in conjunction with suitable experiments and reference data to identify those matrix properties which influence composite strength properties. Composites of graphite fibers and low, intermediate and high-modulus resins were investigated. It was found that the area under the matrix stress/strain diagram limited to one percent strain is a good index for an a priori assessment of the matrix contribution to composite strength. The corresponding initial modulus is a useful parameter in translating matrix properties to composite properties. Matrix properties such as ultimate strength, ultimate elongation, toughness, and fracture toughness are misleading in translating matrix properties to composite strength.

Chamis, C. C.↗

Evaluation of a high response electrohydraulic digital control valve

The application is described of a digital control valve on an electrohydraulic servo actuator. The digital control problem is discussed in general as well as the design and evaluation of a breadboard actuator. The evaluation revealed a number of problems associated with matching the valve to a hydraulic load. The problems were related to lost motion resulting from bulk modulus and leakage. These problems were effectively minimized in the breadboard actuator by maintaining a 1000 psi back pressure on the valve circuit and thereby improving the effective bulk modulus.

Anderson, R. L.↗

Development of polyphenylquinoxaline graphite composites

The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F)has been demonstrated using a block copolymer, BlCo(13), PPQ derivative. Initially, thirteen polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), and tensile strength and modulus at ambient temperature. A block copolymer (Bl Co 13) derived from one mole p-bis (phenylglyoxalyl) benzene, one fourth mole 3,3'-diaminobenzidine and three-fourths mole 3,3', 4,4'-tetraminobenzophenone was selected for extensive study. Tensile, flexural, and interlaminar shear values were obtained after aging and testing postcured BlCo(13) laminates at 316 C (600 F). The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.

Hoggatt, J. T.↗

Light intensity strain analysis

A process is described for the analysis of the strain field of structures subjected to large deformations involving a low modulus substrate having a high modulus, relatively thin coating. The optical properties of transmittance and reflectance are measured for the coated substrate while stressed and unstressed to indicate the strain field for the coated substrate.

Williams, J. G.↗

Development and evaluation of graphite and boron polyimide composites.

This paper covers the development and evaluation of the HT-S/710 graphite/polyimide system and initial evaluations of high modulus graphite and boron reinforced polyimide systems. Detail design properties of the HT-S/710 graphite/polyimide systems, test results of test sheet stringer components, and initial test evaluations of high modulus graphite and boron reinforced polyimide composites are presented. Preliminary design applications utilizing the basic processing and design data from this development program are presented as to their utilization in aircraft and space applications.

Scheck, W. G.↗

Criteria for selecting resin matrices for improved composite strength.

Criteria are presented which can be used a priori to select matrices to yield composites with improved unidirectional strength. The criteria evolved from an investigation including both theoretical and experimental efforts. Composite micromechanics were used in conjunction with suitable experiments and reference data to identify those matrix properties which influence composite strength properties. Composites of graphite fibers and low, intermediate and high-modulus resins were investigated. It was found that the area under the matrix stress/strain diagram limited to one percent strain is a good index for an a priori assessment of the matrix contribution to composite strength. The corresponding initial modulus is a useful parameter in translating matrix properties to composite properties.

Chamis, C. C.↗

Elasticity of some mantle crystal structures. II.

The single-crystal elastic constants are determined as a function of pressure and temperature for rutile structure germanium dioxide (GeO2). The data are qualitatively similar to those of rutile TiO2 measured by Manghnani (1969). The compressibility in the c direction is less than one-half that in the a direction, the pressure derivative of the shear constant is negative, and the pressure derivative of the bulk modulus has a relatively high value of about 6.2. According to an elastic strain energy theory, the negative shear modulus derivative implies that the kinetic barrier to diffusion decreases with increasing pressure.

Wang, H.↗