Search NASA⌕ Search

SEARCH · Search NASA

Results for “Padding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Experimental measurements of the ground cloud effluents and cloud growth for the May 20, 1975, Titan 3C launch at Air Force Eastern Test Range, Florida

The experiment included surface level and airborne in situ cloud measurements of the exhaust effluents from the Titan IIIC solid rocket boosters. Simultaneous visible spectrum photographic pictures of the ground cloud as well as infrared imaging of the cloud were obtained to study the cloud rise, growth, and direction of travel within the earth's surface mixing layer. The NASA multilayer diffusion model predictions of cloud growth, direction of travel, and expected surface level effluent concentrations were made prior to launch and after launch using measured meteorological conditions. Prelaunch predictions were used to position the effluent monitoring instruments, and the postlaunch predictions were compared with the measured data. Measurement results showed that surface level effluent values were low, often below the detection limits of the instrumentation. The maximum surface level hydrogen chloride concentration measured 50 parts per billion at about 8 km from the launch pad. The maximum observed in-cloud (airborne measurement) hydrogen chloride concentration was 7 per million.

Gregory, G. L.↗

Advanced high efficiency wraparound contact solar cell

A significant advancement in the development of thin high efficiency wraparound contact silicon solar cells has been made by coupling space and terrestrial processing procedures. Although this new method for fabricating cells has not been completely reduced to practice, some of the initial cells have delivered over 20 mW/sq cm when tested at 25 C under AMO intensity. This approach not only yields high efficiency devices, but shows promise of allowing complete freedom of choice in both the location and size of the wraparound contact pad area.

Scott-Monck, J. A.↗

Preliminary study of cyclic thermal shock resistance of plasma-sprayed zirconium oxide turbine outer air seal shrouds

Several experimental concepts representing potential high pressure turbine seal material systems were subjected to cyclic thermal shock exposures similar to those that might be encountered under severe engine start-up and shut-down sequences. All of the experimental concepts consisted of plasma-sprayed yttria stabilized ZrO2 on the high temperature side of the blade tip seal shroud. Between the ZrO2 and a cooled, dense metal backing, various intermediate layer concepts intended to mitigate thermal stresses were incorporated. Performance was judged on the basis of the number of thermal shock cycles required to cause loss of seal material through spallation. The most effective approach was to include a low modulus, sintered metal pad between the ZrO2 and the metallic backing. It was also found that reducing the density of the ZrO2 layer significantly improved the performance of specimens with plasma-sprayed metal/ceramic composite intermediate layers.

Bill, R. C.↗

Baykonur

The 'Baykonur' cosmodrome, its functions, operations, and services are described in considerable detail. The launch complex, launching pads, launch structures, launchers with cable masts and propellant loading towers, are included. The sequence of all phases of rocket assembly and preparations for launch are depicted. Prelaunch procedures and the launch itself are described.

Vladimirov, B. P.↗

Wear studies on aircraft brake materials

An investigation of both worn surfaces of friction pads and steel rotors which are being applied in current aircraft brakes has been carried out by employing an X-ray diffraction technique. It consists of the analysis of chemical element distribution in the surface layers. The wear particles were also examined by using the scanning electron microscope. The initiation and growth of surface cracks and the oxidation were emphasized in this investigation. A wear model was proposed for the current aircraft brake materials. Essentially this model proposed that cracks are formed in the surface layer of the brake material due to the normal and frictional stresses. It is primarily surface temperature dependent.

Ho, T. L.↗

Some performance tests of a microarea AES

An Auger electron spectroscopy (AES) system which has a submicron analysis capability is described. The system provides secondary electron imaging, as well as micro- and macro-area AES. The resolution of the secondary electron image of an oxidized Al contact pad on a charge-coupled device chip indicates a primary beam size of about 1000 A. For Auger mapping, a useful resolution of about 4000 A is reported

Todd, G.↗

A unique nozzle cover for the Shuttle booster separation motors

The stringent requirements imposed upon the Shuttle booster separation system led to the development of two unique nozzle cover concepts with potential applications in other space propulsion systems. Major requirements were to (1) protect the booster separation motors (BSMs) from the ascent aerothermal environment; (2) provide a humidity seal for the BSM during storage and readiness on the launch pad; (3) open completely during the ignition transient; and (4) produce no debris during ascent, separation, and booster reentry. The nozzle cover concepts included (1) a frangible reinforced elastomeric cover with a retraction mechanism to remove the cover sections away from the plume, and (2) a stainless steel cover hinged by a plastically deforming torsion pin.

Dettling, J. R.↗

Nondestructive weld test by holography

Hologram with magnification locates poorly bonded pads on solar cell arrays. Innovation is useful for testing assembly of large solar-cell arrays accurately and nondestructively.

Perry, M.↗

Instrumentation for measuring the dynamic pressure on rotating compressor blades

To establish the capability for measurement of oscillatory pressure on rotating blades, miniature fast response semiconductor strain gage pressure transducers (2mm x 0.33mm) were mounted in several configurations on thin titanium and steel compressor blades and subjected to pressure cycles from 1 to 310 kPa during static tests and spin tests. Static test conditions included 20 C to 150 C, 0 to 3000 tensile microstrain, -1000 to +1000 bending microstrain and + or - 650G vibration. The spin test conditions included 20 C to 82 C at 0 to 90,000G. Durability was excellent. Pressure transducer sensitivity changed by only a few percent over this range of environmental conditions. Noise signal due to oscillatory acceleration normal to the diaphragm was acceptable (0.33Pa/G). Noise signal due to oscillatory strain was acceptable (0.5 Pa/microstrain) when the transducer was mounted on a 0.05mm rubber pad, with a total buildup of 0.38mm on the measure surface. Back mounting or partial recessing to eliminate buildup, increased the strain effect to 1.2 Pa/microstrain. Flush mounting within the blade to eliminate buildup reduced the strain effect, but required development of a special transducer shape. This transducer was not available in time for spin tests. Unpredictable zero drift + or - 14 kPa ruled out the use of these mounting arrangements for accurate steady-state (D.C.) measurements on rotating blades. The two best configurations fully developed and spin tested were then successfully applied in the NAS3-20606 rotating fan flutter program for quantitative measurement of oscillatory pressure amplitudes.

Grant, H. P.↗

Development of economical improved thick film solar cell contact

Materials were surveyed to provide candidates for an all metal electrode paste system. These consisted of a major constituent metal powder, a low melting metal powder suitable for a liquid phase sintering medium, and a powder material suitable as an etchant for silicon dioxide at sintering temperatures. By means of thermal gravimetric analysis a suitable binder was identified for low temperature fired inks. The all metal ink concept was first demonstrated with the silver system to avoid the problems of limited process windows encountered with base metal systems. A number of solid materials capable of selectively etching silicon dioxide at modest temperatures were identified. A paste with silver fluoride was screened onto N-type silicon with 5 ohm cm resistivity. The resulting contact pads had excellent adhesion but were not electrically ohmic. Metallurgically, these contacts have equal or better grain structure as commercial inks fired at the same temperatures.

Ross, B.↗

Electrostatically focused intensified charge coupled devices

Work performed to develop intensified charge coupled devices (ICCDs) is presented. Four ICCDs, containing 100 x 160 arrays, were fabricated. Electron gains up to 3200 at 15 keV were achieved. Photocathode sensitivities ranged from 190 to 410 micro A/lumen. Dark currents varied from 11 nA/sq cm to 37 nA/sq cm. There was serious concern about the reliability of the bonding scheme for ICCDs due to occassional bond failure. Two solutions to this problem were developed. One involved a modification of the existing bonding technique, and the other was the development of a protected bond pad employing a barrier metal between the aluminum metallization and the gold bond wire. An accumulation process was characterized with respect to its most critical variable. This characterization led to the achievement of reproducible spectral response and the discovery and elimination of dark current increase associated with this process.

Walker, J. W.↗

Comparison of analysis and experiment for self-acting seals for liquid-oxygen turbopumps

Two LOX turbopump applications were analyzed over ranges of pressure differential and speed. Predictions were compared with test results. A small seal was analyzed up to 141 m/sec and 310 N/sq cm differential and a larger seal up to 147 m/sec and 448 N/sq cm. Tests confirmed analytical predictions of operation without rubbing contact. The seals evidently operated with mostly liquid in the pads and mostly gas across the dam although the best prediction of trends was based on assuming gas throughout the entire seal.

Allen, G. P.↗

Bonding machine for forming a solar array strip

A machine is described for attaching solar cells to a flexable substrate on which printed circuitry has been deposited. The strip is fed through: (1) a station in which solar cells are elevated into engagement with solder pads for the printed circuitry and thereafter heated by an infrared lamp; (2) a station at which flux and solder residue is removed; (3) a station at which electrical performance of the soldered cells is determined; (4) a station at which an encapsulating resin is deposited on the cells; (5) a station at which the encapsulated solar cells are examined for electrical performance; and (6) a final station at which the resulting array is wound on a takeup drum.

Costogue, E. N.↗

Chemical vapor deposition reactor

An improved chemical vapor deposition reactor is characterized by a vapor deposition chamber configured to substantially eliminate non-uniformities in films deposited on substrates by control of gas flow and removing gas phase reaction materials from the chamber. Uniformity in the thickness of films is produced by having reactive gases injected through multiple jets which are placed at uniformally distributed locations. Gas phase reaction materials are removed through an exhaust chimney which is positioned above the centrally located, heated pad or platform on which substrates are placed. A baffle is situated above the heated platform below the mouth of the chimney to prevent downdraft dispersion and scattering of gas phase reactant materials.

Chern, S. S.↗

Environmental effects on space shuttle reusable surface insulation coated with reaction cured glass

Sample titles of the space shuttle reusable surface insulation was subjected alternately to simulated mission heating and either real or simulated environmental exposure for up to 34 cycles. The coating cracked as a result of exposure to high temperature and moisture conditions, and insulation with cracked coatings absorbed significant quantities of water in the launch-pad environment. Cracking was a complex function of time, temperature, and moisture exposure. Cracked coatings remained adherent to the insulation for up to 24 cycles past initial cracking.

Ransone, P. O.↗

Investigation of Proposed Process Sequence for the Array Automated Assembly Task, Phase 2

The technological readiness of the proposed process sequence was reviewed. Process steps evaluated include: (1) plasma etching to establish a standard surface; (2) forming junctions by diffusion from an N-type polymeric spray-on source; (3) forming a p+ back contact by firing a screen printed aluminum paste; (4) forming screen printed front contacts after cleaning the back aluminum and removing the diffusion oxide; (5) cleaning the junction by a laser scribe operation; (6) forming an antireflection coating by baking a polymeric spray-on film; (7) ultrasonically tin padding the cells; and (8) assembling cell strings into solar circuits using ethylene vinyl acetate as an encapsulant and laminating medium.

Mardesich, N.↗

The stability of an asymmetric rotor in damped supports

A general-purpose method of evaluating the stability of an asymmetric flexible rotor, mounted in symmetric damped bearings, is defined. This method evaluates the complex eigenvalues of the rotor system by solving the equations of motion in a rotating coordinate frame. The application of this method to a rotor mounted in tilting-pad bearings is demonstrated. The observed behavior of a number of different rotor configurations is compared with corresponding predictions of stability. For the configurations predicted to be unstable, a distinct and unnegotiable threshold of instability is encountered. The sharpness of this threshold is emphasized by careful balancing at speeds fractionally below the threshold. In a final configuration predicted to be marginally stable, lightly damped resonant behavior, negotiable by balancing, is encountered in the region of the first critical speed.

Smalley, A. J.↗

The effect of fire retardants on the fire response characteristics of cellulosic materials

The resistance to ignition of fire retardant-treated wood, cotton, and cellulose insulation was studied. The proprietary composition used to treat wood was found to increase resistance to ignition and to reduce smoke toxicity. Cotton treated with boric acid (added by padding on or by vapor phase process) was found to have increased resistance to ignition and decreased smoke toxicity. Boric acid increased the resistance of cellulose insulation to ignition but also slightly increased the smoke toxicity.

Hilado, C. J.↗