Search NASA⌕ Search

SEARCH · Search NASA

Results for “circularity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

The use of curvilinear fiber format to improve buckling resistance of plates with central circular holes

The potential gain in buckling resistance is explored by using the curvilinear format with a plate containing a centrally located circular hole and subjected to a uniaxial compressive load. The buckling loads for a uniform stress loading and simple support boundary conditions were examined. The method of analysis is outlined for the buckling improvement study. Several designs that represent an improvement over a baseline quasi-isotropic design (a design that is quite good for buckling resistance) are discussed. The tensile load of these designs is examined. A recommended design is presented that not only shows an improved buckling capacity, but also shows improved tensile performance. Follow-on activities are also discussed.

Lee, H. H.↗

Compression behavior of graphite-epoxy and graphite-thermoplastic panels with circular holes or impact damage

An experimental investigation of the compression behavior of laminated specimens made from graphite-epoxy tape (AS4-3502), graphite-thermoplastic tape (AS4-PEEK), and graphite-thermoplastic fabric (AS4-PEEK) was conducted. Specimens with five different stacking sequences were loaded to failure in uniaxial compression. Some of the specimens had central circular holes with diameters up to 65 percent of the specimen width. Other specimens were subjected to low speed impact with impact energy up to 30 J prior to compressive loading. This investigation indicates that graphite-thermoplastic specimens with holes have up to 15 percent lower failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and hole size. However, graphite-thermoplastic specimens subjected to low speed impact have up to 15 percent higher failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and impact energy. Compression tests of graphite-thermoplastic specimens constructed of unidirectional tape and of fabric indicate that the material form has little effect on failure strains in specimens with holes or low speed impact damage.

Jegley, Dawn C.↗

Robust, angstrom level circularity profilometry

A noncontacting approach is presented which involves measuring the local circumferential curvature of the test piece by simultaneously measuring its circumferential slope at two slightly displaced locations. A pair of sensing beams is scanned along the circumference, and a profile of curvature is built, from which the circularity profile is deduced. The sensing of curvature makes the approach insensitive to all types of vibration and drift and runout errors in the relative rotation. The special qualities of the approach are summarized which make it well suited to measuring cylindrical optics and enable it to accommodate radii as small as twenty millimeters.

Glenn, Paul↗

Analysis of a slot loaded microstrip disk antenna for circular polarisation

A method is presented to analyze a circular microstrip disk antenna loaded with a narrow, inclined slot at its center and fed by a coaxial probe. Making use of the exact dyadic Green's functions for a grounded dielectric slab due to electric and magnetic currents, Richmond's reaction integral equation in conjunction with the method of moments (Galerkin), a generalized h-parameter equivalent network for the loaded patch is obtained. An expression for the input impedance of a slot loaded microstrip patch is obtained from the equivalent parameters. The theoretical results are compared with the experiment.

Rao, Y. R.↗

Constant covariance in local vertical coordinates for near-circular orbits

A method is presented for devising a covariance matrix that either remains constant or grows in keeping with the presence of a period error in a rotating local-vertical coordinate system. The solution presented may prove useful in the initialization of simulation covariance matrices for near-circular-orbit problems. Use is made of the Clohessy-Wiltshire equations and the travelling-ellipse formulation.

Shepperd, Stanley W.↗

Large quasi-circular features beneath frost on Triton

Specially processed Voyager 2 images of Neptune's largest moon, Triton, reveal three large quasi-circular features ranging in diameter from 280 to 935 km within Triton's equatorial region. The largest of these features contains a central irregularly shaped area of comparatively low albedo about 380 km in diameter, surrounded by crudely concentric annuli of higher albedo materials. None of the features exhibit significant topographic expression, and all appear to be primarily albedo markings. The features are located within a broad equatorial band of anomalously transparent frost that renders them nearly invisible at the large phase angles (alpha greater than 90 deg) at which Voyager obtained its highest resolution coverage of Triton. The features can be discerned at smaller phase angles (alpha = 66 deg) at which the frost only partially masks underlying albedo contrasts. The origin of the features is uncertain but may have involved regional cryovolcanic activity.

Helfenstein, Paul↗

Compression failure mechanisms of uni-ply composite plates with a circular cutout

The effect of circular-hole size on the failure mode of uniply graphite-epoxy composite plates is investigated experimentally and analytically for uniaxial compressive loading. The test specimens are sandwiched between polyetherimide plastic for nondestructive evaluations of the uniply failure mechanisms associated with a range of hole sizes. Finite-element modeling based on classical lamination theory is conducted for the corresponding materials and geometries to reproduce the experimental results analytically. The type of compressive failure is found to be a function of hole size, with fiber buckling/kinking at the hole being the dominant failure mechanism for hole diam/plate width ratios exceeding 0.062. The results of the finite-element analysis supported the experimental data for these failure mechanisms and for those corresponding to smaller hole sizes.

Khamseh, A. R.↗

Orbit maintenance for low altitude near-circular lunar orbits

The behavior of low altitude near-circular lunar orbits is a key design issue for some missions in the proposed Space Exploration Initiative. The lunar gravity field strongly perturbs low altitude orbits, so an effective orbit maintenance strategy is needed. This strategy must contend with the long term orbit evolution due to the zonal gravity field. Two possible orbit control scenarios are passive control using a frozen orbit and active orbit control using maneuvers. A maneuver strategy can be designed which optimizes the propellant required for long term orbit sustenance. The long term requirements dominate the total propellant required for orbit control. Additional propellant may be required to offset the impact of medium period gravity field effects. Careful selection of maneuver times and directions, however, can eliminate any medium period penalty.

Cook, Richard A.↗

Heat transfer in thin, compact heat exchangers with circular, rectangular, or pin-fin flow passages

Heat transfer and pressure drop have been measured of three thin, compact heat exchangers in helium gas at 3.5 MPa and higher, with Reynolds numbers of 450 to 36,000. The flow geometries for the three heat exchanger specimens were: circular tube, rectangular channel, and staggered pin fin with tapered pins. The specimens were heated radiatively at heat fluxes up to 77 W/sq cm. Correlations were developed for the isothermal friction factor as a function of Reynolds number, and for the Nusselt number as a function of Reynolds number and the ratio of wall temperature to fluid temperature. The specimen with the pin fin internal geometry had significantly better heat transfer than the other specimens, but it also had higher pressure drop. For certain conditions of helium flow and heating, the temperature more than doubled from the inlet to the outlet of the specimens, producing large changes in gas velocity, density, viscosity, and thermal conductivity. These changes in properties did not affect the correlations for friction factor and Nusselt number in turbulent flow.

Olson, D. A.↗

The long-term behavior of near-circular orbits in a zonal gravity field

A simple solution has been developed for the long term behavior of a near-circular orbit in a zonal gravity field. The solution is obtained by linearizing the singly averaged variational equations of motion and eliminating a degree of freedom with an integral of motion. The resulting solution is expressed in semiequinoctial elements (h and k), and has either an exponential or periodic form. The type of solution is dependent upon a stability factor determined by the inclination and the values of the gravity field coefficients. Frozen orbits correspond to the equilibrium solutions of the set of simplified variational equations. An approximate expression for the location of these orbits has been developed and can be useful for certain mission design applications.

Cook, Richard A.↗

Failure mechanisms of uni-ply composite plates with a circular hole under static compressive loading

The objective of the study was to identify and study the failure mechanisms associated with compressive-loaded uniply graphite/epoxy square plates with a central circular hole. It is found that the type of compressive failure depends on the hole size. For large holes with the diameter/width ratio exceeding 0.062, fiber buckling/kinking initiated at the hole is found to be the dominant failure mechanism. In plates with smaller hole sizes, failure initiates away from the hole edge or complete global failure occurs. Critical buckle wavelengths at failure are presented as a function of the normalized hole diameter.

Khamseh, A. R.↗

Three-dimensional shock-wave/boundary-layer interactions with bleed through a circular hole

Computations were performed to study three-dimensional (3-D), shock-wave/boundary-layer interactions on a flat plate in which fluid in the boundary layer was bled through a circular hole into a plenum to control shock-wave induced separation. Results are presented which show the details of the 3-D flowfield about the bleed hole and how bleed-hole placement relative to shock-wave impingement affect upstream, spanwise, and downstream influence lengths. This study revealed an underlying mechanisms by which bleed holes can affect shock-wave/boundary-layer interactions. This investigation is based on the ensemble-averaged, "full-compressible" Navier-Stokes equations closed by the Baldwin-Lomax turbulence model. Solutions to these equations were obtained by an implicit finite-volume method based on the partially-split, two-factored algorithm of Steger.

Rimlinger, M. J.↗

Bohemian circular structure, Czechoslovakia: Search for the impact evidence

Test of the impact hypothesis for the origin of the circular, 260-km-diameter structure of the Bohemian Massif led to the discovery of glasses and breccias in the Upper Proterozoic sequence that can be compared to autogeneous breccias of larger craters. The black recrystallized glass contains small exsolution crystals of albite-oligoclase and biotite, regularly dispersed in the matrix recrystallized to quartz. The occurrence of these rocks is limited to a 1-sq-km area. It is directly underlain by the breccia of the pelitic and silty rocks cemented by the melted matrix, found on several tens of square kilometers. The melt has the same chemistry as rock fragments in major and in trace elements. It is slightly impoverished in water. The proportion of melted rocks to fragments varies from 1:5 to 10:1. The mineralogy of melt viens is the function of later, mostly contact metamorphism. On the contact of granitic plutons it abounds on sillimanite, cordierite, and small bullets of ilmenite. Immediately on the contact with syenodiorites it contains garnets. The metamorphism of the impact rock melt seems the most probable explanation of the mineralogy and the dry total fusion of rocks accompanied by the strong fragmentation. Other aspects of this investigation are discussed.

Rajlich, Petr↗

Optimization of circular orifice jets mixing into a heated cross flow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

Study of narrow-band dichroic plates with circular, rectangular, or Pyleguide apertures

The dichroic plate considered in this article is a metal plate perforated with arrays of apertures such that electromagnetic waves of certain frequencies pass through the plate and other frequencies are reflected. The shape of the apertures is an important contributor to the performance of the dichroic plate. An S/X dichroic plate, which passes X-band (8.4-8.45 GHz) and reflects S-band (2.0-2.32 GHz), is chosen for a case study. A comparison of the performance of dichroic plates of the same thickness and array pattern is presented for three different aperture shapes: circular, Pyleguide, and rectangular.

Chen, J. C.↗

Optimization of circular orifice jets mixing into a heated crossflow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

On the generation of secondary motion in circular to rectangular transition ducts

A computer code has been developed for the calculation of three-dimensional turbulent flow in circular to rectangular transition ducts. The governing equations are written in a general curvilinear coordinate system so that all singly-connected geometrical configurations can be accommodated. Turbulence closure is through the standard k-epsilon model or a Reynolds stress closure model. Computed results show qualitative agreement with experimental data. Pressure-induced secondary flow is the dominant mode through the transition, but turbulence-induced secondary flow becomes prominent some distance downstream of the transition.

Demuren, A. O.↗

Parametric instabilities of circularly polarized Alfven waves in high-beta plasmas

CGL relations including the effect of finite ion Larmor radius are used to consider a class of parametric instabilities of finite-amplitude, circularly polarized Alfven waves in high-beta plasmas. The disperison relation governing the instabilities is a sixth-order polynomial which is solved numerically. There are two types of instabilities: a modulational instability at k is less than k(0) and a relatively weak and narrow bandwidth instability at k is less than approximately k(0), where k and k(0) are the wavenumbers of the unstable density fluctuation and the 'pump' wave, respectively. It is shown that these instabilities can occur for left-handed pump waves and that the modulational instability is unstable over a very broad band in k with a maximum growth rate at finite k is not equal to 0.

Hamabata, Hiromitsu↗