Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase 1 Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

The Design of an Ultra-Low Background Thermosyphon for the Majorana Demonstrator

The MAJORANA DEMONSTRATOR (MJD) is an ultra-low background neutrinoless double-beta decay (0νββ) experiment that will deploy up to 40 kg of high purity germanium detectors (HPGe). The goal of this experiment is to demonstrate the feasibility of building a detector array with less than 1 event/ton-year in a 4 keV region of interest around the 0νββ signal. HPGe diodes, when used as ionizing radiation detectors, need to be maintained at a temperature close to that of liquid nitrogen (77 K). This work describes the R&D results of a cryogenic system capable of meeting the requirements of low background and the cooling capacity required to successfully operate such a detector system. The MJD germanium detector modules will operate at liquid nitrogen temperature to provide adequate cooling for a full range of HPGe impurity concentrations. This paper shows the experimental results obtained using a two-phase horizontal thermosyphon using liquid nitrogen as the MJD’s cooling system. The cold test shows that the proposed thermosyphon has sufficient cooling power to handle the heat load of an MJD module. Results for the temperature gradient across the thermosyphon, cooling capacity, and design considerations demonstrate that the thermosyphon can effectively remove the calculated heat load of each module of the experiment. The thermosyphon will be bolted to a cold plate from which detector strings will hang. The thermal conductivity of a mockup of the MJD bolted thermal joint is experimentally determined to be below 0.1 K/W.

Detector arrays↗

Direct glycerol fuel cell with polytetrafluoroethylene (PTFE) thin film separator

Here, anion-exchange membrane-based direct glycerol fuel cells (AEM-DGFCs) can yield high power density, however challenges exist in developing chemically stable AEMs. Here, we demonstrate a porous PTFE thin film, a well-known chemical, electro-chemical, and thermal robust material that can serve as a separator between anode and cathode, thus achieving high DGFC’s performance. A simple aqueous-phase reduction method was used to prepare carbon nanotube supported PdAg nanoparticles (PdAg/CNT) with an average particle size of 2.9 nm. A DGFC using a PTFE thin film without any further modification with PdAg/CNT anode catalyst exhibits a peak power density of 214.7 mW cm –2 at 80 °C, about 22.6% lower than a DGFC using a state-of-the-art AEM. We report a 5.8% decrease and 11.1% decrease in cell voltage for a PTFE thin film and AEM; similarly, the cell voltage degradation rate decreases from 1.2 to 0.8 mV h –1 for PTFE thin film, while for AEM, it decreases from 9.6 to 3.0 mV h –1 over an 80 h durability test period. Transmission electron microscopy results indicate that the average particle size of PdAg/CNT increases from 2.9 to 3.7 nm after 80 h discharge; this suggests that PdAg particle growth may be the main reason for the performance drop.

30 DIRECT ENERGY CONVERSION↗

Toward Understanding the Simulated Phase Partitioning of Arctic Single-Layer Mixed-Phase Clouds in E3SM

21 Mixed-phase clouds are widespread in the Arctic and have substantial impacts on the 22 surface energy budget, sea ice extent, and regional climate. Significant changes are found in the 23 modeled phase partitioning of Arctic mixed-phase clouds in the newly developed U.S. 24 Department of Energy (DOE) Energy Exascale Earth System Model (E3SM) Atmosphere Model 25 version 1 (EAMv1) compared to its predecessor (CAM5/EAMv0). The mixed-phase clouds 26 simulated by EAMv1 is overly dominated by super-cool liquid which is often underestimated by 27 CAM5. Compared to CAM5, EAMv1 has made several important changes in its cloud physical 28 parameterizations, including using CLUBB to unify shallow convection, PBL turbulence, and 29 cloud macrophysics, as well as updating the MG two-moment cloud microphysics scheme and 30 using the CNT heterogeneous ice nucleation scheme to replace the Meyers scheme for mixed- 31 phase clouds. To understand which of the newly-implemented physical parameterizations is 32 responsible for the change of modeled mixed-phase cloud phase partitioning in EAMv1, 33 sensitivity tests are conducted by utilizing the short-term hindcast approach and results are 34 compared to the observations from the ARM Mixed-Phase Arctic Cloud Experiment (M-PACE) 35 field campaign. 36 It is found that although each scheme contributes to the decrease of cloud ice water 37 content (IWC) and increase of cloud liquid water content (LWC), only the combined effect of 38 CLUBB and CNT can explain the significant underestimation of IWC. By examining the budgets 39 of cloud microphysical processes, CLUBB is found to play a dominant role due to the fact that 40 CLUBB does not diagnoses cloud ice phase water in its assumed joint PDF method and thus may 41 not provide sufficient cloud ice to initialize ice phase microphysical processes such as the growth 42 of ice crystals through vapor deposition. Although a more effective heterogeneous ice nucleation 43 may alleviate the underestimation of IWC, the ice phase process in CLUBB requires urgent 44 attention in the future model development.

Zhang, Meng↗

Conversion of CH{sub 4}/CO{sub 2} to syngas over Ni-Co/Al{sub 2}O{sub 3}-ZrO{sub 2} nanocatalyst synthesized via plasma assisted co-impregnation method: Surface properties and catalytic performance

Ni/Al{sub 2}O{sub 3} catalyst promoted by Co and ZrO{sub 2} was prepared by co-impregnation method and treated with glow discharge plasma. The catalytic activity of the synthesized nanocatalysts has been tested toward conversion of CH{sub 4}/CO{sub 2} to syngas. The physicochemical characterizations like XRD, EDX, FESEM, TEM, BET, FTIR, and XPS show that plasma treatment results in smaller particle size, more surface concentration, and uniform morphology. The dispersion of nickel in plasma-treated nanocatalyst was also significantly improved, which was helpful for controlling the ensemble size of active phase atoms on the support surface. Improved physicochemical properties caused 20%–30% enhancement in activity of plasma-treated nanocatalyst that means to achieve the same H{sub 2} or CO yield, the plasma-treated nanocatalyst needed about 100 °C lower reaction temperature. The H{sub 2}/CO ratio got closer to 1 at higher temperatures and finally at 850 °C H{sub 2}/CO = 1 is attained for plasma-treated nanocatalyst. Plasma-treated nanocatalyst due to smaller Ni particles and strong interaction between active phase and support has lower tendency to keep carbon species on its structure and hence excellent stability can be observed for this catalyst.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-flux ptychographic imaging using the new 55 µm-pixel detector ‘Lambda’ based on the Medipix3 readout chip

The Large Area Medipix-Based Detector Array (Lambda) has been used in a ptychographic imaging experiment on solar-cell nanowires. By using a semi-transparent central stop, the high flux density provided by nano-focusing Kirkpatrick–Baez mirrors can be fully exploited for high-resolution phase reconstructions. Suitable detection systems that are capable of recording high photon count rates with single-photon detection are instrumental for coherent X-ray imaging. The new single-photon-counting pixel detector ‘Lambda’ has been tested in a ptychographic imaging experiment on solar-cell nanowires using Kirkpatrick–Baez-focused 13.8 keV X-rays. Taking advantage of the high count rate of the Lambda and dynamic range expansion by the semi-transparent central stop, a high-dynamic-range diffraction signal covering more than seven orders of magnitude has been recorded, which corresponds to a photon flux density of about 10{sup 5} photons nm{sup −2} s{sup −1} or a flux of ∼10{sup 10} photons s{sup −1} on the sample. By comparison with data taken without the semi-transparent central stop, an increase in resolution by a factor of 3–4 is determined: from about 125 nm to about 38 nm for the nanowire and from about 83 nm to about 21 nm for the illuminating wavefield.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phase II Study of Neoadjuvant Bevacizumab and Radiotherapy for Resectable Soft Tissue Sarcomas

Purpose: Numerous preclinical studies have demonstrated that angiogenesis inhibitors can increase the efficacy of radiotherapy (RT). We sought to examine the safety and efficacy of bevacizumab (BV) and RT in soft tissue sarcomas and explore biomarkers to help determine the treatment response. Methods and Materials: Patients with {>=}5 cm, intermediate- or high-grade soft tissue sarcomas at significant risk of local recurrence received neoadjuvant BV alone followed by BV plus RT before surgical resection. Correlative science studies included analysis of the serial blood and tumor samples and serial perfusion computed tomography scans. Results: The 20 patients had a median tumor size of 8.25 cm, with 13 extremity, 1 trunk, and 6 retroperitoneal/pelvis tumors. The neoadjuvant treatment was well tolerated, with only 4 patients having Grade 3 toxicities (hypertension, liver function test elevation). BV plus RT resulted in {>=}80% pathologic necrosis in 9 (45%) of 20 tumors, more than double the historical rate seen with RT alone. Three patients had a complete pathologic response. The median microvessel density decreased 53% after BV alone (p <.05). After combination therapy, the median tumor cell proliferation decreased by 73%, apoptosis increased 10.4-fold, and the blood flow, blood volume, and permeability surface area decreased by 62-72% (p <.05). Analysis of gene expression microarrays of untreated tumors identified a 24-gene signature for treatment response. The microvessel density and circulating progenitor cells at baseline and the reduction in microvessel density and plasma soluble c-KIT with BV therapy also correlated with a good pathologic response (p <.05). After a median follow-up of 20 months, only 1 patient had developed local recurrence. Conclusions: The results from the present exploratory study indicated that BV increases the efficacy of RT against soft tissue sarcomas and might reduce the incidence of local recurrence. Thus, this regimen warrants additional investigation. Gene expression profiles and other tissue and circulating biomarkers showed promising correlations with treatment response.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Development and data path integration test of the global Feature EXtractor for the ATLAS Level-1 calorimeter trigger system Phase-I upgrade

The global Feature Extractor (gFEX) is a component of the Phase-I upgrade of the Level-1 Calorimeter (L1Calo) trigger system for the ATLAS experiment at the Large Hadron Collider (LHC) at CERN. The gFEX is used to identify patterns of energy associated with the hadronic decays of high momentum Higgs, W and Z bosons, top quarks, and exotic particles in real time at the 40 MHz LHC bunch crossing rate. Three prototypes were implemented and tested from 2014 to 2017. With the lessons learned from the prototypes, the final gFEX production board has been implemented at the end of 2017. The gFEX receives up to 300 fiber optical links from the calorimeter and transmits trigger data on 96 links to the ATLAS Level-1 Topological [1] (L1Topo) trigger at a rate of up to 12.8 Gb/s. There are also 24 electrical links on board for communication between two FPGAs running at speeds of up to 25.6 Gb/s. Here, the hardware functionality and performance of the production board have been evaluated. A data path integration test between the Liquid Argon Digital Processing Blade (LDPB) [2] and the Front End LInk eXchange (FELIX) [3] was performed successfully at CERN in 2018.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Negative Ion Photoelectron Spectroscopy Confirms the Prediction that (CO)5 and (CO)6 Each Has a Singlet Ground State

Cyclobutane-1,2,3,4-tetraone has been both predicted and found to have a triplet ground state, in which a b2g MO and an a2u MO is each singly occupied. In contrast, (CO)5 and (CO)6 have each been predicted to have a singlet ground state. This prediction has been tested by generating the (CO)5 - and (CO)6 - anions in the gas-phase by electrospray vaporization of solutions of, respectively, the croconate (CO)52- and rhodizonate (CO)62- dianions. The negative ion photoelectron (NIPE) spectra of the (CO)5•- radical anion give electron affinity (EA) = 3.830 eV and a singlet ground state for (CO)5, with the triplet higher in energy by 0.850 eV (19.6 kcal/mol). The NIPE spectra of the (CO)6•- radical anion give EA = 3.785 eV and a singlet ground state for (CO)6, with the triplet higher in energy by 0.915 eV (21.1 kcal/mol). (RO)CCSD(T)/aug-cc-pVTZ//(U)B3LYP/6-311+G(2df) calculations give EA values that are only ca. 1 kcal/mol lower than those measured and EST values that are only 2 - 3 kcal/mol higher than those obtained from the NIPE spectra. Thus, the calculations support the interpretations of the NIPE spectra and the finding, based on the spectra, that (CO)5 and (CO)6 both have a singlet ground state.

Environmental Molecular Sciences Laboratory↗

PHASE-RESOLVED X-RAY SPECTRA OF MAGNETARS AND THE CORONAL OUTFLOW MODEL

We test a model recently proposed for the persistent hard X-ray emission from magnetars. In the model, hard X-rays are produced by a decelerating electron-positron flow in the closed magnetosphere. The flow decelerates as it radiates its energy away via resonant scattering of soft X-rays, then it reaches the top of the magnetic loop and annihilates there. We test the model against observations of three magnetars: 4U 0142+61, 1RXS J1708-4009, and 1E 1841-045. We find that the model successfully fits the observed phase-resolved spectra. We derive constraints on the angle between the rotational and magnetic axes of the neutron star, the object inclination to the line of sight, and the size of the active twisted region filled with the plasma flow. Using the fit of the hard X-ray component of the magnetar spectrum, we revisit the remaining soft X-ray component. We find that it can be explained by a modified two-temperature blackbody model. The hotter blackbody is consistent with a hot spot covering 1%-10% of the neutron star surface. Such a hot spot is expected at the base of the magnetospheric e {sup ±} outflow, as some particles created in the e {sup ±} discharge flow back and bombard the stellar surface.

79 ASTRONOMY AND ASTROPHYSICS↗

Probability of Encounter Between Ports of Entry (PrEP): Aversion Force-Field “Early Validation” Report

To enhance detection and interdiction of radiological or nuclear material trafficking between primary POEs into the US, The Department of Homeland Security is faced with highly variable smuggling pathways through expansive geographic regions. The goal of this project is to test an approach to estimating likely pathways, as well as the probability of encounter along any given route. Our goal is to test the feasibility of a novel approach based on assessing the adversary’s perception of discovery likelihood over a broad geographic region, and using that result to estimate an “aversion force field” over the same region. The aversion force field is derived from analogies based on the physics of electric charges. Combining the aversion force with the intention of an adversary to reach their destination, generates a route that is consistent with both the adversary’s intention and their aversion to deterrent measures. Phase I is exploratory. Its goal to demonstrate the feasibility of the approach. This report describes progress in an essential part of the approach, specifically, to implement and couple two principle model components: (1) the Bayesian network model of an adversary’s perception of discovery likelihood; and (2) the physics-inspired aversion field model. The objective is to show that the field produced from the two components is plausible and consistent with the assumptions and the data. Figure 1 illustrates the workflow of this phase to the present stage. After collecting preliminary data and implementing each of the two model components, they were separately evaluated. Following this step, the output from the Bayesian network was input to the aversion field solver, and the combined results evaluated as reported here.

97 MATHEMATICS AND COMPUTING↗

A versatile elevated-pressure reactor combined with an ultrahigh vacuum surface setup for efficient testing of model and powder catalysts under clean gas-phase conditions

A small-volume reaction cell for catalytic or photocatalytic testing of solid materials at pressures up to 1000 Torr has been coupled to a surface-science setup used for standard sample preparation and characterization under ultrahigh vacuum (UHV). The reactor and sample holder designs allow easy sample transfer from/to the UHV chamber, and investigation of both planar and small amounts of powder catalysts under the same conditions. The sample is heated with an infrared laser beam and its temperature is measured with a compact pyrometer. Combined in a regulation loop, this system ensures fast and accurate temperature control as well as clean heating. The reaction products are automatically sampled and analyzed by mass spectrometry and/or gas chromatography (GC). Unlike previous systems, our GC apparatus does not use a recirculation loop and allows working in clean conditions at pressures as low as 1 Torr while detecting partial pressures smaller than 10{sup −4} Torr. The efficiency and versatility of the reactor are demonstrated in the study of two catalytic systems: butadiene hydrogenation on Pd(100) and CO oxidation over an AuRh/TiO{sub 2} powder catalyst.

36 MATERIALS SCIENCE↗

Controlled Pyrolysis: A Robust Scalable Composite Recycling Technology

The reinforced composites industry is facing significant challenges in handling the scrap composite material from automobile manufacturing, the wind turbine industry, and others. The fibers in the material, whether they be carbon, glass, or other materials have commercial value if they can be recovered successfully. Successfully means the fibers are clean with no sizing or other binders and have adequate strength and physical properties that would allow them to be economically reprocessed into valuable product. The composites recycling project was an industry-collaborative effort to develop a composite recycling technology using controlled pyrolysis. Through the recycling of scrap and end-of-life (EOL) cured composite materials, this pilot study was intended to create a business case by realizing a cost-effective means for recycling EOL and production scrap composite materials, ultimately reducing the volume of composite materials destined for landfill. The project was led by the Institute for Advanced Composites Manufacturing Innovation (IACMI), the American Composites Manufacturers Association (ACMA), Oak Ridge National Laboratory (ORNL), Continental Structural Plastics (CSP) a Teijin Group Company, CHZ Technologies, and A. Schulman with support from Owens Corning, John Deere, General Electric (GE), Ashland LLC, and Plastics Europe (CEFIC). The team studied and tested CHZ Technologies’ controlled pyrolysis system, known as the Thermolyzer TM , which operates on a scalable basis to convert organic polymer materials into a clean synthesis gas and char containing the recoverable carbon and glass fiber reinforcement. The recoverable energy contained in the input polymers creates the synthesis gas that can be used to provide heat to the Thermolyzer TM primary reactor in a sustainable manner. That is, once the Thermolyzer TM is started with a small amount of external natural gas, the synthesis gas that is created from the polymers will continue to operate the burners so long as feedstock is supplied. The reinforcing fiber materials remaining in the solid phase char were separated and cleaned for re-use in other polymer systems based on the retained properties of the fibers. The study created reports (attached in the appendix) on the Mass and Energy Balances, syngas analytics, VOC assessment, yield analysis and other analytics necessary for a Techno-Economic Analysis (TEA) to quantify the economic impact of the recovery and sustainable re-use of the carbon and glass fibers. The process consisted of 4 steps: Selection of 4 samples of cured composite waste materials from project partners interested in materials recycling and recovering the reinforcing fibers for best case re-use. The materials included glass fiber (GF) polyester/vinyl ester automotive SMC from CSP, GF epoxy balsa/PVC foam wind blades from GE, carbon fiber (CF) epoxy wind blade laminated spar caps from GE, and GF/CF epoxy hybrid assembly from John Deere. Processing the waste composite samples into 1-2” shreds. Packaging the shredded composites into bulk sacks on international shipping pallets for shipment to KUG in Forst (Lausitz), Germany. Pyrolysis of the shredded composites under controlled conditions designed for each polymer system. Collecting samples of the gas and char for analysis. Shipping the char containing the CF/GF back to the US for the next steps of testing the fibers and developing protocols for sustainable re-use of the fibers in composite applications.

36 MATERIALS SCIENCE↗

Temperature-dependent micromechanical behavior of medium-Mn transformation-induced-plasticity steel studied by in situ synchrotron X-ray diffraction

The temperature-dependent micromechanical behavior of medium-Mn transformation-induced-plasticity (TRIP) steel with a nominal chemical composition of Fe-0.1C-10Mn-2Al (mass%) fabricated by intercritical annealing 650 ºC for 1 h after cold-rolling, was investigated using in situ high-energy X-ray diffraction (HE-XRD) with uniaxial tensile tests at temperatures of 100, 25 and -50 ºC. We find that as the deformation temperature decreases, the Luders strain decreases and more austenite transforms to martensite during Luders band propagation. The Luders bands are associated with sudden changes of lattice strain in austenite. At 100 ºC, austenite is too stable to transform to martensite, resulting in limited work-hardening capability and a relatively low strain to failure. At 25 ºC, the austenite is found to transform in bursts during applied loading. These transformations correlate with stepwise peak broadening in the austenite phase and are attributed to Portevin-Le Chatelier (PLC) band propagation. At -50 ºC, we then observe a more intense TRIP effect which suppresses PLC band formation and leads to a high ultimate tensile strength. In addition to the TRIP effect, we find that work hardening in the deformation-induced martensite phase plays an important role in the plastic stability at low temperature, by accommodating stress compatibility between grains and phases. Our studies provide the first direct experimental evidence for the existence of large stress concentrations in the austenite phase near the Luders band propagation front. These observations help to deepen understanding of the complex temperature-dependent micromechanical behaviors of advanced medium-Mn TRIP steels.

36 MATERIALS SCIENCE↗

Sulfuric acid resistance of one-part alkali-activated mortars

One-part alkali-activated (geopolymer) mortars based on three different silica-rich starting materials and sodium aluminate, with and without ground granulated blast furnace slag (GGBFS) addition, were tested regarding sulfuric acid resistance according to DIN 19573:2016-03 (70 days at pH = 1). Corresponding pastes were characterized by XRD, SEM, chemical analysis, {sup 29}Si MAS NMR and {sup 1}H-{sup 29}Si CPMAS NMR after water storage and after acid exposure. The mortars exhibited a high resistance against sulfuric acid attack, with the best ones conforming to the requirements of DIN 19573:2016-03. The analytical results showed that this was due to precipitation of silica gel at the acid-mortar interface, which formed a mechanically stable layer that protected the subjacent mortar and thus inhibited further degradation. The addition of GGBFS decreased the acid resistance via formation of expansive calcium sulfate phases.

36 MATERIALS SCIENCE↗

Evaluation of 3D pixel silicon sensors for the CMS Phase-2 Inner Tracker

The high-luminosity upgrade of the CERN LHC requires the replacement of the CMS tracking detector to cope with the increased radiation fluence while maintaining its excellent performance. An extensive R&D program, aiming at using 3D pixel silicon sensors in the innermost barrel layer of the detector, has been carried out by CMS in collaboration with the FBK (Trento, Italy) and CNM (Barcelona, Spain) foundries. The sensors will feature a pixel cell size of 25 × 100 µm 2 , with a centrally located electrode connected to the readout chip. The sensors are read out by the RD53A and CROCv1 chips, developed in 65 nm CMOS technology by the RD53 Collaboration, a joint effort between the ATLAS and CMS groups. This paper reports the results achieved in beam test experiments before and after irradiation, up to a fluence of approximately 2 . 6 × 1 0 16 n eq /cm 2 . Measurements of assemblies irradiated to a fluence of 1 × 10 16 n˙eq/cm 2 show a hit detection efficiency higher than 96% at normal incidence, with fewer than 2% of channels masked, across a bias voltage range greater than 50 V . Even after irradiation to a higher fluence of 1.6 × 10 16 n˙eq/cm 2 , similar performance is maintained over a bias voltage range of 30 V , remaining well within CMS requirements.

3D pixel↗

Benefits to decomposition rates when using digestate as compost co-feedstock: Part I – Focus on physicochemical parameters

Highlights: • Co-composting OFMSW and digestate results in improved composting rates. • Reactors with 20–40% (%ww) digestate had the best performance. •Stability time was 30–36% shorter in the reactors with 20–40% digestate (%ww). •Inhibition at high digestate levels probably due to ammonia. • TAN from the digestate may have improved carbon removal rates. - Abstract: Anaerobic digestion (AD) has gained a significant role in municipal solid waste management, but managing a high volume of digestate is one of the challenges with AD technology. One option is to mix digestate with fresh and/or stabilized organic waste and then feed to the composting process. In this study, the effect of co-composting anaerobic digestate (in different quantities) on a composting process was investigated. The digestate was prepared in a pilot-scale 500 L high solids dry anaerobic digester and composting was completed in eight 25 L reactors with different ratios of digestate to fresh feedstock from the organic fraction of municipal solid waste (OFMSW). The digestate constituted 0, 10, 20, 30, 40, 50, 75, or 100% (wet mass) of the feedstock. The co-composting experiment was conducted in two phases: active aeration and curing. Monitored parameters included: process temperature, aeration rate, oxygen concentration of the outlet gas, mass changes, total solids, organic matter, pH, and electrical conductivity. In addition, respirometry, C:N ratio, ammonium to nitrate ratio, and Solvita® tests were used to quantify stability and maturity end points. The results showed that the addition of digestate to the OFMSW increased composting reaction rates in all cases, with peak performance occurring within the ratio of 20–40% of digestate addition on a wet weight basis. Reactor performance may have been influenced by the high total ammonia nitrogen (TAN) levels in the digestate. Composting rates increased as TAN levels increased up to 5000 TAN mg kg{sup −1} DM; however, TAN may have become inhibitory at higher levels.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Solid Xenon Project

Crystals like Germanium and Silicon need to be grown in specialized facilities which is time and money costly. It takes many runs to test the detector once it's manufactured and mishaps are very probable. It is of a great challenge to grow big germanium crystals and that's why stacking them up in a tower is the only way at the moment to increase testing mass. Liquid Noble gas experiments experiencing contamination problems, their predicted energy resolution at 10 keV and lower energy range is not as good as predicted. Every experiment is targeting one specific purpose, looking for one thing. Why not to design an experiment that is diverse and build a detector that can search for Dark Matter, Solar Axions, Neutrinoless Double Beta decay, etc. Solid Xenon detector is such detector. We designed a simple Xenon crystal growing chamber that was put together at Fermi National Accelerator Laboratory. The first phase of this experiment was to demonstrate that a good, crack free Xenon crystal can be grown (regardless of many failed attempts by various groups) and our first goal, 1 kg crystal, was successful.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Infrastructure Development of Single Cell Testing Capability at A0 Facility

The objective of this technical note is to document the details of the infrastructure development process that was realized at the A0 photo injector facility to establish RF cold testing capability for 1.3 GHz superconducting niobium single cell cavities. The activity began the last quarter of CY 2006 and ended the first quarter of CY 2009. The whole process involved addressing various aspects such as design of vertical insert and lifting fixture, modification of existing RF test station and design of new couplers, development of a Temperature Mapping (T-Map) system, radiation considerations for the test location (north cave), update of existing High Pressure Rinse (HPR) system, preparation of necessary safety documents and eventually obtaining an Operational Readiness Clearance (ORC). Figure 1 illustrates the various components of the development process. In the past, the north cave test station at A0 has supported the cold testing 3.9 GHz nine cell and single cell cavities, thus some of the components were available for use and some needed modification. The test dewar had the capacity to accommodate 1.3 GHz single cells although a new vertical insert that could handle both cavity types (1.3 and 3.9 GHz) had to be designed. The existing cryogenic system with an average capacity of {approx} 0.5 g/sec was deemed sufficient. The RF system was updated with broadband components and an additional amplifier with higher power capacity to handle higher gradients usually achieved in 1.3 GHz cavities. The initial testing phase was arbitrated to proceed with fixed power coupling. A new temperature mapping system was developed to provide the diagnostic tool for hot spot studies, quench characterization and field emission studies. The defining feature of this system was the use of diode sensors instead of the traditional carbon resistors as sensing elements. The unidirectional current carrying capacity (forward bias) of the diodes provided for the ease of multiplexing of the system, thus substantially reducing the number of cables required to power the sensors. The high gradient capacity of the 1.3 GHz cavities required a revision of the radiation shielding and interlocks. The cave was updated as per the recommendations of the radiation safety committee. The high pressure rinse system was updated with new adapters to assist the rinsing 1.3 GHz single cell cavities. Finally, a proposal for cold testing 1.3 GHz single cell cavities at A0 north cave was made to the small experiments approval committee, radiation safety committee and the Tevatron cryogenic safety sub-committee for an operational readiness clearance and the same was approved. The project was classified under research and development of single cell cavities (project 18) and was allocated a budget of $200,000 in FY 2007.

43 PARTICLE ACCELERATORS↗