Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reactor Structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Ultra High Temperature (UHT) SiC Fiber (Phase 2)

Silicon-carbide fiber-reinforced silicon-carbide ceramic matrix composites (SiCSiC CMC) are emerginglightweight re-usable structural materials not only for hot section components in gas turbine engines, but also for controlsurfaces and leading edges of reusable hypersonic vehicles as well as for nuclear propulsion and reactor components. Ithas been shown that when these CMC are employed in engine hot-section components, the higher the upper usetemperature (UUT) of the SiC fiber, the more performance benefits are accrued, such as higher operating temperatures,reduced component cooling air, reduced fuel consumption, and reduced emissions. The first generation of SiCSiC CMC with a temperature capability of 2200-2400F are on the verge of being introduced into the hot-section components ofcommercial and military gas turbine engines.Today the SiC fiber type currently recognized as the worlds best in terms ofthermo-mechanical performance is the Sylramic-iBN fiber. This fiber was previously developed by the PI at NASA GRC using patented processes to improve the high-cost commercial Sylramic fiber, which in turn was derived from anotherlow-cost low-performance commercial fiber. Although the Sylramic-iBN fiber shows state-of-the art creep and rupture resistance for use temperatures above 2550oF, NASA has shown by fundamental creep studies and model developmentthat its microstructure and creep resistance could theoretically be significantly improved to produce an Ultra HighTemperature (UHT) SiC fiber.This Phase II Seedling Fund effort has been focused on the key objective of effectively repeating the similar processes used for producing the Sylramic-iBN fiber using a design of experiments approach to first understand the cause of the less than optimum Sylramic-iBN microstructure and then attempting to develop processconditions that eliminate or minimize these key microstructural issues. In so doing, it is predicted that that theseadvanced process could result in an UHT SiC fiber with 20 times more creep resistance than the Sylramic-iBN fiber,which in turn would allow SiCSiC CMC to operate up to 2700oF and above, thereby further enhancing the performancebenefits of SiCSiC components in aero-propulsion engines. It was also envisioned that the fiber processes developedduring Phase II efforts would not only reduce production costs for the UHT fiber by using low-cost precursor fibers andcombined processes, but also allow the UHT fibers to be directly produced in preforms of the precursor fibers, possibly atthe facilities of the CMC fabricator.

SiC Ceramic Fiber↗
DOE OSTI2022

Effect of Water Chemistry on Crack Growth Rates in Neutron Irradiated X-750 and XM-19

The Advanced Test Reactor (ATR) National Science User Facility (NSUF) was used to study the effect of neutron damage on crack growth rates (CGR) under simulated boiling water reactor (BWR) water chemistry conditions using a fast neutron spectrum to accelerate the damage process. Nickel based Alloy X-750 and XM-19 were irradiated in the ATR center flux trap (CFT), with this experiment marking the first civilian project to utilize this position within the reactor. 0.4T-CT specimens were used to study crack growth rates for two sample fluences (~1.9 x 1020 n/cm2 and ~9.5 x 1020 n/cm2, E > 1MeV) in both normal water chemistry (NWC) at 2.5 ppm O2 and hydrogen water chemistry (HWC) at ~80 ppb H2. A decrease in CGR was observed with HWC for both alloys with the average ratio (CGR in NWC/CGR in HWC) being a factor of 281 for the XM-19 samples and a factor of 27.8 for the X-750 samples. Observed CGRs in this study showed little difference compared to non-irradiated samples (the non-irradiated XM-19 was 20% cold worked), suggesting limited sensitivity of these susceptible alloys to irradiation effects. The CGR response to varying environmental electrochemical potential (ECP) and water purity will be presented.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Preliminary Analysis of a Nuclear Grade Sandwich Composite for Transportable Micro-Reactor Shielding

Transportable microreactors pose a unique shielding challenge compared with conventional reactors. Many vendors are seeking to transport a microreactor to a site, operate it for a number of years, and then transport it to a secondary site. This involves ensuring the reactor has sufficient shielding during operations and post-irradiation transportation to ensure the safety of those around it, all while ensuring it can be transported via traditional means. This work examines the use of a nuclear grade sandwich composite (NGSC) which seeks to combine the reactor pressure vessel and biological shielding into a single unit. Through this work, it was determined that the NGSC was sufficient to adequately reduce neutron and gamma current exiting the structure to warrant further investigation as a potential shielding option for microreactors.

42 ENGINEERING↗
DOE OSTI2022

Summary of Development for Structural Component Modeling in Fiscal Year 2022

This report summarizes efforts performed during Fiscal Year 2022 to develop capabilities for modeling structural component degradation in support of the U.S. Department of Energy's Nuclear Energy Advanced Modeling and Simulation Program. These efforts were centered around development of capabilities for the Grizzly code. Efforts focused both on foundational engineering-scale analysis capabilities for damage and shell formulations and on material-scale tools for accounting for irradiation effects in Grade 91 steel. A major outcome of this effort was the development of a general-purpose tool for nonlocal averaging of material properties, which enabled nonlocal damage models. In addition, the applicability of the shell elements in MOOSE has been expanded to allow modeling a wider range of component geometries and using a wide variety of material models. For irradiation effects on materials, a previously developed cluster dynamics model for light water reactor pressure vessel steels has been adapted for application to Grade 91 alloy. This work builds on prior efforts to build a flexible, capable code for addressing a variety of aging and component performance issues in nuclear power plant structural components.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structure of high-lying levels populated in the 96 Y → 96 Zr β decay

The nature of the high-lying final levels of the 96 Y gs β decay, one of the three most important contributors to the high-energy reactor antineutrino spectrum, has been investigated in high-resolution γ-ray spectroscopy following the β decay as well as in a campaign of inelastic photon scattering experiments. The comprehensive approach establishes 1 - levels associated with the Pygmy Dipole Resonance as high-lying final levels in the β decay. Branching ratios extracted from β decay complement photon scattering and allow the absolute E1 excitation strength to be determined for levels populated in both reactions. The combined data represents a comprehensive approach to the wavefunction of the 1 - levels below the Qβ value, which are investigated in the Quasiparticle Phonon Model. The calculations reveal that the components populated in β decay contribute only with small amplitudes to the complex wavefunction of these 1 - levels. A comparison of the β decay results to data from total absorption γ -ray spectroscopy demonstrates a good agreement between both measurements.

Pygmy dipole resonance↗
DOE OSTI2021

Radiation Stability of MOF Engineered Particles

Pacific Northwest National Laboratory (PNNL), in collaboration with Flibe Energy, demonstrated the fabrication of metal organic frameworks (MOFs) into engineered beads to manage off-gases released from advanced reactors, including molten salt reactors. Based on the commercial availability and easy to synthesis at scale, PNNL down-selected two MOF sorbents known as CuBTC and UiO-67. The sorbents were synthesized, characterized, and fabricated into mechanically robust engineered beads (composites) using wet granulation method using polymer as a binder. Further, MOF powders and and mechanically robust composites were exposed to gamma radiation using Co-60 source and characterized irradiated MOFs to demonstrate the structural stability. Among the two MOF sorbents identified, the CuBTC MOF was shown to be very promising for noble gas management at low temperature (193 K) compared to UiO-67 MOF. The high adsorption capacity of the synthesized composites was correlated to the high surface area and pore volume of the CuBTC MOF. Both MOFs retain structural integrity and long-range order even after exposure to 1000 kGy of radiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Feasibility of Recycling Discharged Microreactor Heavy Metal in Light Water and Sodium-Cooled Fast Reactors: A Neutronics Analysis

Nuclear microreactors (MRs) offer unique advantages, such as rapid deployment, potability, low maintenance requirements, and operational flexibility. Their compact size makes them a promising solution for decentralized power generation, particularly in remote areas, military bases, and disaster-stricken regions. However, MRs face challenges, including unutilized fissile material at the end of life, economic inefficiency, increased heavy metal (HM) waste complicating disposal, and the accumulation of plutonium (Pu) with high 239 Pu concentrations raising proliferation risks. Here, this study investigated the neutronics feasibility of a novel three-stage fuel cycle where discharged HM from MRs is recycled and burned in light water reactors and sodium-cooled fast reactors. This approach converts discharged HM into valuable fuel, enhancing the efficiency of MR deployments while improving the safeguardability of their final waste products. Neutronics analysis demonstrated that the safety characteristics of reactor designs in each stage were minimally impacted by the proposed cycle. For two representative MR designs, a fast-spectrum MR with solid pellet fuel and a thermal-spectrum MR with TRISO (TRi-structural-ISOtropic) fuel compacts, the proposed fuel cycle reduced the uranium disposal mass flow rate by ~60%, decreased the 235 U enrichment of the discharge fuel to ~1 wt%, eliminated plutonium disposal, and increased the cumulative fuel burnup to ~580 gigawatt-day per metric ton of initial heavy metal (GWd/t-iHM) or 60% fissions per initial metal atom. Despite the significant differences between the two MR designs, the performance and infrastructure requirements of the developed fuel cycles were remarkably similar, indicating its generalizability to a broader class of MRs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Core Reactivity Control for a Soluble Boron Free Small Modular Reactor

Soluble boron has been used in pressurized water reactors (PWRs) to control the core excess reactivity in a uniform and stable way without distorting power distributions. It also enables current commercial PWRs to have high core power density. Despite its outstanding advantages, the soluble boron raises several significant concerns such as soluble boron-induced corrosion of structures, a large amount of liquid waste generation, and a possibility of positive moderator temperature coefficient (MTC) at high boron concentration. These concerns become more serious as the concentration of boron becomes higher. Therefore boron in the primary coolant has been a hindrance to the power uprate and cycle extension operation of PWRs. Currently a government-supported research project is underway to develop technologies for the soluble-boron-free (SBF) operation of a PWR-type small modular reactor (SMR). This paper presents preliminary results of the SBF SMR core reactivity control methods including optimization of burnable absorbers (BA) and control rod design, and development of secondary shutdown system (SSS)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Mid-height seismic isolation of equipment in nuclear power plants: Numerical simulations and design recommendations

Seismic isolation can mitigate earthquake demands on safety-class equipment and is being considered for application to some advanced nuclear reactors. For tall, slender vessels that could represent an advanced reactor, a steam generator or a heat exchanger, mid-height seismic isolation has been shown to be beneficial and practical. Here, this paper focuses on numerical modeling of a mid-height isolated tall, slender vessel with two primary goals 1) investigate and quantify the benefits of mid-height seismic isolation for a range of support structure stiffnesses, isolation systems, and seismic inputs, and 2) provide analysis and design recommendations for isolation of safety-class equipment. Results of response-history analysis were in good agreement with experimental measurements and demonstrated that mid-height isolation can substantially reduce seismic demands on tall, slender vessels for a range of support structure stiffnesses, isolation systems, and seismic inputs. Importantly, the reductions in horizontal spectral accelerations in the mid-height isolated vessel from the non-isolated condition were not affected by the stiffness of the support structure. Recommendations are made for analysis and design of isolated equipment and testing of isolators used for equipment protection in nuclear facilities, which are also applicable to other industries.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2018

Status Report on HTR Research, Development, and Deployment in the USA

Abstract – The Gas-Cooled Reactor deployment effort in the United States is a collaboration between the US government and private vendors. The US Department of Energy sponsors the qualification of fuels, materials, and analysis methods that exploit the capabilities of the national laboratories (mainly Idaho, Oak Ridge, and Argonne) to generate the fundamental fuel, material, and core behavior data needed to support design and licensing efforts by vendors in general. Private HTR vendors provide input to the R&D program and engage in the design of the systems, structures, and components that are unique to their design concepts. Their plant design all exploit the properties and behavior of the TRISO fuel, graphite, and alloys being tested in the DOE qualification programs. This paper will summarize the goals and recent progress of the US Gas-Cooled Reactor Program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Compositionally-driven surface nanostructuring on refractory compositionally complex alloys under low energy helium bombardment

Additive manufacturing enables user-defined control of the compositional complexity, opening new design spaces for complex concentrated alloys (CCAs). Refractory CCAs may offer enhanced performance in the divertor region of a fusion reactor environment where plasma-facing materials will be subject to high temperatures, low energy He and D particles, and 14 MeV neutrons. In this work, specimens with the nominal composition of NbTaMoTi, NbTaMo, NbTaTi, and NbTa were fabricated via directed energy deposition (DED) then bombarded with 40 eV He ions to a fluence of 2x10 26 m −2 at ∼ 1000 K. Post irradiation, the surface morphology and composition were examined with electron microscopy and x-ray photoelectron spectroscopy to offer information on the spatial distribution of surface nano-structuring. Sub-surface He bubbles driving the nano-structuring were examined with electron microscopy techniques. Analysis indicates the local composition directly influences the He bubble and tendril size, while the region with the highest complexity showed the shortest nano-structuring. Molecular Dynamics simulations complement the experimental results, showing comparable helium bubble growth and migration as a function of compositional complexity. This work demonstrates the compositional dependence of surface nanostructure formation of compositionally complex alloys, important for future design of complex plasma facing materials in fusion reactors.

Complex concentrated alloys↗
DOE OSTI2022

Reactor Physics Simulations of the High Flux Isotope Reactor Permanent Beryllium Reflector Number 5 Design

This study evaluates reactor physics aspects of the proposed High Flux Isotope Reactor (HFIR) permanent beryllium reflector number 5 design. HFIR is a pressurized, light water–cooled, and beryllium reflected research reactor that operates at 85 MW for cycle lengths of approximately 24 to 26 days. A new permanent reflector design is highly desirable for increased versatility in irradiation experiments, to arrange the vertical experiment facilities (VXFs) to minimize their impact on neutron scattering if loaded with neutronabsorbing experiments, to enhance reflector thermal-structural-hydraulic performance, and to simplify the complex fabrication process. The current number 4 and concept number 5 reflectors have 22 and 28 VXFs, respectively, and are modeled and analyzed in this study with the MCNP5 and SCALE 6.1.3 nuclear simulation codes.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1973

Effect of nitrogen on tensile properties and structures of T-111 (tantalum, 8 percent tungsten, 2 percent hafnium) tubing

The effect of controlled nitrogen additions was evaluated on the mechanical properties of T-111 (Ta-8W-2Hf) fuel pin cladding material proposed for use in a lithium-cooled nuclear reactor concept. Additions of 80 to 1125 ppm nitrogen resulted in increased strengthening of T-111 tubular section test specimens at temperatures of 25 to 1200 C. Homogeneous distributions of up to 500 ppm nitrogen did not seriously decrease tensile ductility. Both single and two-phase microstructures, with hafnium nitride as the second phase, were evaluated in this study.

Buzzard, R. J.↗
DOE OSTI2025

Effect of energetic ions on edge-localized modes in tokamak plasmas

The most efficient and promising operational regime for the International Thermonuclear Experimental Reactor tokamak is the high-confinement mode. In this regime, however, periodic relaxations of the plasma edge can occur. These edge-localized modes pose a threat to the integrity of the fusion device. Here we reveal the strong impact of energetic ions on the spatio-temporal structure of edge-localized modes in tokamaks using nonlinear hybrid kinetic–magnetohydrodynamic simulations. A resonant interaction between the fast ions at the plasma edge and the electromagnetic perturbations from the edge-localized mode leads to an energy and momentum exchange. Energetic ions modify, for example, the amplitude, frequency spectrum and crash timing of edge-localized modes. The simulations reproduce some observations that feature abrupt and large edge-localized mode crashes. The results indicate that, in the International Thermonuclear Experimental Reactor, a strong interaction between the fusion-born alpha particles and ions from neutral beam injection, a main heating and fast particle source, is expected with predicted edge-localized mode perturbations. This work advances the understanding of the physics underlying edge-localized mode crashes in the presence of energetic particles and highlights the importance of including energetic ion kinetic effects in the optimization of edge-localized mode control techniques and regimes that are free of such modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

SEM/EBSD Characterization of Baffle-Former Bolts Designated for High Energy X-ray Microscopy Studies at the Advanced Photon Source

This report documents the microstructural and surface characterization of two high-fluence baffle-former bolts (BFBs) harvested from a commercial pressurized water reactor (PWR) after nearly four decades of service. These bolts experienced extreme conditions including high neutron fluence, elevated temperatures, corrosive primary water, and sustained mechanical loads, all of which contribute to degradation mechanisms such as irradiation-assisted stress corrosion cracking (IASCC). Using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), the study assessed bulk and near-surface microstructures, grain boundary characteristics, and in-service oxide layers. The results revealed significant differences between bolts exposed to 41 dpa and 29 dpa, including differences in recrystallization extent, deformation structures, and oxidation morphology. These findings establish critical baseline data for integration with advanced synchrotron-based high-energy X-ray microscopy (HEXM) and computational crystal plasticity models. Ultimately, the work supports improved mechanistic understanding and predictive capability regarding the long-term performance of reactor core internal components.

Lach, Tim [Oak Ridge National Laboratory (ORNL), O↗
DOE OSTI2017

Plastic Deformation Processes Accompanying Stress Corrosion Crack Propagation in Irradiated Austenitic Steels

During stress corrosion crack propagation, stress values in the crack tip vicinity often exceed material yield stress limit. Plastic deformation processes may accompany and influence cracking. Here, stress corrosion crack propagation and deformation mechanisms were investigated using EBSD analysis. The investigated material was 304L Ti-enriched austenitic stainless steel irradiated to 10.4 dpa at 320°C in the BOR-60 fast reactor. Crack growth tests were conducted in a simulated Normal Water Chemistry (NWC) environment in the temperature range 288–320 °C using compact tension specimens. By analyzing crack trajectory and grain structure in the crack vicinity, it was established that grain orientation with respect to the acting stress direction was not a key factor controlling crack propagation. No crystallographic orientation susceptible to cracking was identified. Also, EBSD analysis revealed strong inhomogeneity in plastic strain distribution along the crack path. Most crack-adjacent grains remained virtually strain-free whereas few grains experienced strong plastic strain. These areas were presumed to be “plastic bridges” or “ductile ligaments.”

Gussev, Maxim N↗
DOE OSTI2020

Quantification of silicon carbide grain structure in TRISO fuel by BSE image analysis

The grain structure of the silicon carbide (SiC) layer in tristructural-isotropic (TRISO) fuels has commonly been qualified in fuel specifications based on a qualitative comparison to visual standards to ensure undesirable microstructure are not produced. This approach is inherently dependent on subjective judgement and provides limited data for analysis or comparison. An alternative method to rapidly quantify (i.e., provide a numeric measure of) the grain structure of the SiC layer in TRISO fuels has been developed. This method relies on the identification of silicon carbide grain boundaries based on brightness variation in backscattered electron (BSE) images through the application of automated image processing algorithms. The speed with which the requisite BSE imaging and analysis may be completed enables the practical use of this method on an industrial scale as a part of qualifying TRISO fuel to meet a given specification on silicon carbide grain structure, which is an important parameter for TRISO fuel performance. The method is benchmarked by comparison to prior Electron-Backscattered Diffraction (EBSD) results for TRISO particles from the Advanced Gas Reactor (AGR) program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗