SEARCH · Search NASA

Results for “sensor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,603 records · Page 89

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Combinatorial Sensor Design in Caulobacter crescentus for Selective Environmental Uranium Detection

The ability to detect uranium (U) through environmental monitoring is of critical importance for informing water resource protection and nonproliferation efforts. Although technologies exist for environmental U detection, wide-area environmental monitoring, i.e. sampling coverage over large areas not known to possess U contamination, remains a challenging prospect that necessitates the development of novel detection approaches. In this work, we describe the development of a whole-cell U sensor by integrating two functionally independent, native U-responsive two-component signaling systems (TCS), UzcRS and UrpRS, within an AND gate circuit in the bacterium Caulobacter crescentus. Through leverage of the distinct but imperfect selectivity profiles of both TCS, this combinatorial approach enabled greater selectivity relative to a prior biosensor developed with UzcRS alone; no cross-reactivity was observed with most common environmental metals (e.g, Fe, As, Cu, Ca, Mg, Cd, Cr, Al) or the U decay-chain product Th, and the selectivity against Zn and Pb was significantly improved. In addition, integration of the UzcRS signal amplifier protein UzcY within the AND gate circuit further enhanced overall sensitivity and selectivity for U. The functionality of the sensor in an environmental context was confirmed by detection of U concentrations as low as 1 μM in groundwater samples. The results illustrate the value of a combinatorial approach for constructing whole-cell sensors for the selective detection of analytes for which there are no known evolved regulators.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2021

Equalization of Intensity-Modulated Fiber-Optic Voltage Sensors for Power Distribution Systems

We test fiber-optic voltage sensors based on optical reflection from a piezoelectric transducer. Our specific devices possess a 2 kHz fundamental resonance, and we verify a readily usable frequency band from approximately 10 Hz to 3 kHz, with a dynamic range of 60 dB for a detection system integrating over this entire band. Additionally, we demonstrate a digital signal processing approach to equalize the measured frequency response, enabling accurate retrieval of short-pulse inputs. These results suggest the value and applicability of intensity-modulated fiber-optic voltage sensors for measuring both steady-state waveforms and broadband transients which, coupled with the straightforward and compact design of the sensors, should make them effective tools in electric grid monitoring.

42 ENGINEERING↗

DOE OSTI2021

Multi-sensor anomalous change detection in remote sensing imagery

Combining multiple satellite remote sensing sources provides a far richer, more frequent view of the earth than that of any single source; the challenge is in distilling these petabytes of heterogeneous sensor imagery into meaningful characterizations of the imaged areas. Meeting this challenge requires effective algorithms for combining multi-modal imagery over time to identify subtle but real changes among the intrinsic data variation. Here, we implement a joint-distribution framework for multi-sensor anomalous change detection (MSACD) that can effectively account for these differences in modality, and does not require any signal resampling of the pixel measurements. This flexibility enables the use of satellite imagery from different sensor platforms and modalities. We use multi-year construction of the SoFi Stadium in California as our testbed, and exploit synthetic aperture radar imagery from Sentinel-1 and multispectral imagery from both Sentinel-2 and Landsat 8. We show results for MSACD using real imagery with implanted, measurable changes, as well as real imagery with real, observable changes, including scaling our analysis over multiple years.

47 OTHER INSTRUMENTATION↗

NASA NTRSDate not supplied

Flight Test Configuration of the Sensor Payload and the Ground Nodes in Distributed Sensing Frameworks

The realization of the Urban Air Mobility (UAM) vision, entailing the deployment of high-density autonomous flights over urban areas, necessitates methodologies transcending contemporary airborne sensing techniques. An instrumental innovation in this realm is the advent of distributed sensing. In this paradigm, environmental sensors function as active agents, engaging in the triad of sensing, processing, and communication either amongst themselves, with ground stations, or both. This concerted effort creates a dynamic and responsive "smart space," facilitating real-time autonomous control. NASA Ames Research Center is actively engaged in a series of comprehensive indoor and outdoor flight tests to garner requisite data and insights essential for the actualization of this ambitious vision. This paper delineates the holistic configuration of the flight payload and the distributed ground nodes pivotal to the NASA flight test campaign. Furthermore, it expounds upon the intricacies of the sensor node communication framework. The narrative extends to provide a detailed overview of the strategic placement of distributed sensors and a comprehensive account of the varied indoor and outdoor flight tests orchestrated in pursuit of UAM objectives.

urban air mobility↗

NASA NTRSDate not supplied

Flight Test Configuration of the Sensor Payload and the Ground Nodes in Distributed Sensing Frameworks

urban air mobility↗

DOE OSTI2020

Microengineering Pressure Sensor Active Layers for Improved Performance

Abstract Pressure sensors play an integral role in a wide range of applications, such as soft robotics and health monitoring. In order to meet this demand, many groups microengineer the active layer—the layer that deforms under pressure and dictates changes in the output signal—of capacitive, resistive/piezoresistive, piezoelectric, and triboelectric pressure sensors in order to improve sensor performance. Geometric microengineering of the active layer has been shown to improve performance parameters such as sensitivity, dynamic range, limit of detection, and response and relaxation times. There are a wide range of implemented designs, including microdomes, micropyramids, lines or microridges, papillae, microspheres, micropores, and microcylinders, each offering different advantages for a particular application. It is important to compare the techniques by which the microengineered active layers are designed and fabricated as they may provide additional insights on compatibility and sensing range limits. To evaluate each fabrication method, it is critical to take into account the active layer uniformity, ease of fabrication, shape and size versatility and tunability, and scalability of both the device and the fabrication process. By better understanding how microengineering techniques and design compares, pressure sensors can be targetedly designed and implemented.

Ruth, Sara Rachel Arussy↗

DOE OSTI2020

Single Bimodular Sensor for Differentiated Detection of Multiple Oxidative Gases

Semiconductive metal-oxide sensors suffer from cross-sensitivities under mixed chemical condition, specifically upon mixture of multiple oxidative or reductive gases. Herein, a single bimodular sensor is demonstrated for smart differentiation of multiple oxidative analytes by relating the resistance-metric mode to impedance-metric mode. The sensor construct based on ZnO nanorods readily outputs three response datasets upon exposure of oxidative-gas mixture including O 2 , SO 2 , and NO 2 , the resistance, real part impedance, and imaginary part impedance. The differentiative and correlated nature between these response signals allows such a single sensor platform to differentiate these oxidative gases accurately and robustly. Linear and non-linear decision boundaries are established over a large gas-concentration range from 2 ppm to 3% through a combination of principal component analysis and artificial neural network training. A facile user interface is demonstrated for recognition and measurement of unknown gas analytes, with the error of the predicted analyte-concentration as low as 2%.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Resonant Mode Engineering of Photonic Crystal Sensors Clad with Ultralow Refractive Index Porous Silicon Dioxide

Porous SiO 2 (PSiO 2 ) with ultralow refractive index ($n$ = 1.09) is incorporated as the cladding of a photonic crystal (PC) refractive index sensor with enhanced sensitivity through the establishment of resonant modes that principally reside in the liquid medium covering the PC surface. PSiO 2 , obtained by thermal oxidation of porous Si that has been transferred to a transparent substrate, is transparent at visible and near infrared wavelengths with a refractive index determined by its porosity. The PSiO 2 periodic grating structure ($Λ$ = 590 nm) is patterned by nanoimprint lithography and reactive ion etching, then conformally coated by sputtering high refractive index TiO 2 to seal the pores from liquid infiltration. With the refractive index of PSiO 2 much lower than that of water, the resonant mode “flips” its spatial distribution from within the solid dielectric regions of the photonic crystal to reside mainly in the water media covering the PC, resulting in 4× greater resonant wavelength shift for a fixed refractive index change. This study demonstrates design, fabrication, and testing of the sensor as a refractometer, supported by electromagnetic simulations of the resonant mode spatial distribution, in which porous PC sensors are compared to nonporous PC sensors.

14 SOLAR ENERGY↗

DOE OSTI2016

Monitoring the Strain Evolution of Lithium‐Ion Battery Electrodes using an Optical Fiber Bragg Grating Sensor

Abstract More advanced characterization and developmental tools are essential to improve the performance and safety of Li‐ion batteries. Conventional tools have been limited to customized test cell configurations that require special facilities and expensive equipment. As a practical solution for the in situ monitoring of realistic battery cells, we have embedded fiber optic sensors within Li‐ion battery pouch cells to monitor the internal electrode strain and temperature during cycling. Here we report the direct monitoring of strain evolution using implanted fiber‐optic sensors within the individual electrodes in a Li‐ion battery. Reproducible peak shifting and splitting in the implanted fiber optic sensor originate from the accumulated longitudinal and transverse strains associated with the expansion or contraction of the anode electrode. These discoveries demonstrate the feasibility and utility of fiber Bragg grating (FBG) sensors to be used as diagnostic tools in the development of new battery materials and structures.

Bae, Chang‐Jun↗

DOE OSTI2025

Field validation of dynamic mechanical torque measurements using fiber-optic strain sensors for geared wind turbines

Abstract Accurate knowledge of the mechanical loads of wind turbine gearboxes has become essential in modern, highly loaded gearbox designs, as maintaining or even improving gearbox reliability with increasing torque density demands is proving to be challenging. Unfortunately, the traditional method of measuring dynamic mechanical torque using strain gauges placed on the outer surface of a rotating shaft and transmitting the resulting signal is unsuitable for serial deployment due to technical and economic constraints. An alternative method based on fiber-optic strain sensors placed on the stationary outer surface of the gearbox ring gear has been proposed. Like shaft torsion, the radial deformation of the ring gear is proportionate to the rotor torque. Placing the sensors on a stationary component is a cost-effective alternative for serial implementation because the need for complex and expensive data transfer via wireless transmission or a slip ring is eliminated. In this paper, we present the results of an extensive field experiment conducted to evaluate the torque measurement accuracy of this novel sensing solution installed on the gearbox of a Gamesa G97 2-MW wind turbine at the National Renewable Energy Laboratory’s Flatirons Campus. Torque measurements derived from fiber-optic strain sensors placed on the ring gear of the planetary stage are compared to conventional torque measurements from strain gauges placed on the main shaft. Two different torque estimation data processing methods were evaluated, with the method based on operational deflection shapes providing the most accurate results with an average normalized root mean square error below 0.7% for a load revolution distribution analysis. The effect of operating conditions on the torque estimate was also investigated, and the third planet-passing operational deflection shape was found to be the least sensitive to nontorque load-related effects. The fiber-optic strain sensors’ successful operation during the complete test campaign has demonstrated a robust and accurate solution for fleet-wide enhanced gearbox remaining useful life estimation.

17 WIND ENERGY↗

DOE OSTI2022

Radio-Frequency Resonances and Damping in Metallic Magnetic Calorimeter Sensors

Metallic magnetic calorimeters (MMCs) are particle detectors that combine ultra-high energy resolution with a predictable and smooth response based on the physics of paramagnetism. For best energy resolution, MMCs are read out with dc SQUID preamplifiers. Since the ac Josephson effect also makes dc SQUIDs broadband RF sources in the 1–100 GHz range, the SQUID can potentially excite RF modes of the MMC sensor, with negative consequences. Further, the importance of this possibility is magnified in direct-coupled MMCs, where the MMC sensor is part of the SQUID loop to maximize performance. For these reasons, the RF behavior of MMC sensors must be investigated. In this report, we present the results of exploratory RF simulations of MMC sensor modes and damping, and we assess three approaches to damp the parallel-meander direct-coupled MMC without excessive noise increase.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2018

Additively manufactured mixed potential electrochemical sensors for NO x , C 3 H 8 , and NH 3 detection

Additive manufacturing of mixed potential electrochemical sensors opens the possibility to perform rapid prototyping of electrode and electrolyte materials. We report for the first time the use of this technique for the fabrication of solid-state electrochemical gas sensors of the mixed potential type and assessment of variability in the manufacturing process. La 0.87 Sr 0.13 CrO 3 (LSCO) and Pt electrodes bridged with a porous yttria-stabilized zirconia (YSZ) have been deposited on YSZ substrates by direct-write extrusion of pastes and inks. The sensors are evaluated for their sensitivity to 200 ppm of NO x , C 3 H 8 , and NH 3 . There is a need to understand how variations in intrinsic materials parameters during manufacturing such as differences in porosity affect the gas sensing of additively manufactured sensors to guide optimization of their performance and serve as quality control techniques. Further characterizations of these devices include electrochemical impedance spectroscopy and an aqueous electrochemical assessment of the electrode surface area and diffusion through the porous layer. In conclusion, we find a correlation of increased sensitivity with larger gas reaction impedance, higher Pt electrode surface area, and slower diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2016

Bisphenol-A sensors on polyimide fabricated by laser direct writing for on-site river water monitoring at attomolar concentration

This work presents an aptamer-based, highly sensitive and specific sensor for atto- to femtomolar level detection of bisphenol A (BPA). Because of its widespread use in numerous products, BPA enters surface water from effluent discharges during its manufacture, use, and from waste landfill sites throughout the world. On-site measurement of BPA concentrations in water is important for evaluating compliance with water quality standards or environmental risk levels of the harmful compound in the environment. The sensor in this work is porous, conducting, interdigitated electrodes that are formed by laser-induced carbonization of flexible polyimide sheets. BPA-specific aptamer is immobilized on the electrodes as the probe, and its binding with BPA at the electrode surface is detected by capacitive sensing. The binding process is aided by ac electroosmotic effect that accelerates the transport of BPA molecules to the nanoporous graphene-like structured electrodes. The sensor achieved a limit of detection of 58.28 aM with a response time of 20 s. The sensor is further applied for recovery analysis of BPA spiked in surface water. In conclusion, this work provides an affordable platform for highly sensitive, real time, and field-deployable BPA surveillance critical to the evaluation of the ecological impact of BPA exposure.

36 MATERIALS SCIENCE↗

DOE OSTI2015

Nanoalloy Printed and Pulse-Laser Sintered Flexible Sensor Devices with Enhanced Stability and Materials Compatibility

While conformal and wearable devices have become one of the most desired formats for printable electronics, it is challenging to establish a scalable process that produces stable conductive patterns but also uses substrates compatible with widely available wearable materials. Here, we describe findings of an investigation of a nanoalloy ink printed and pulsed laser sintered conductive patterns as flexible functional devices with enhanced stability and materials compatibility. While nanoparticle inks are desired for printable electronics, almost all existing nanoparticle inks are based on single-metal component, which, as an electronic element, is limited by its inherent stabilities of the metal such as propensity of metal oxidation and mobility of metal ions, especially in sintering processes. The work here has demonstrated the first example in exploiting plasmonic coupling of nanoalloys and pulsed-laser energy with controllable thermal penetration. The experimental and theoretical results have revealed clear correlation between the pulsed laser parameters and the nanoalloy structural characteristics. The superior performance of the resulting flexible sensor device, upon imparting nanostructured sensing materials, for detecting volatile organic compounds has significant implications to developing stable and wearable sensors for monitoring environmental pollutants and breath biomarkers. This simple “nanoalloy printing 'laser sintering' nanostructure printing” process is entirely general to many different sensor devices and nanostructured sensing materials, enabling the ability to easily construct sophisticated sensor array.

Environmental Molecular Sciences Laboratory↗

DOE OSTI2019

Development of a subsurface LIBS sensor for in situ groundwater quality monitoring with applications in CO 2 leak sensing in carbon sequestration

Sub-surface activity such as geologic carbon sequestration (GCS) has the potential to contaminate groundwater sources with dissolved metals originating from sub-surface brines or leaching of formation rock. Therefore, a Laser Induced Breakdown Spectroscopy (LIBS) based sensor is developed for sub-surface water quality monitoring. The sensor head is built using a low cost passively Q-switched (PQSW) laser and is fiber coupled to a pump laser and a gated spectrometer. The prototype sensor head was constructed using off the shelf components and a custom monolithic, PQSW laser and testing has verified that the fiber coupled design performs as desired. The system shows good calibration linearity for tested elements (Ca, Sr, and K), quick data collection times, and Limits of Detection (LODs) that are comparable to or better than those of table top, actively Q-switched systems. The fiber coupled design gives the ability to separate the PQSW LIBS excitation laser from the pump source and spectrometer, allowing these expensive and fragile components to remain at the surface while only the low-cost, all optical sensor head needs to be exposed to the hostile downhole environment.

58 GEOSCIENCES↗

DOE OSTI2020

A magnetic sensor using a 2D van der Waals ferromagnetic material

Two-dimensional (2D) van der Waals ferromagnetic materials are emerging as promising candidates for applications in ultra-compact spintronic nanodevices, nanosensors, and information storage. Our recent discovery of the strong room temperature ferromagnetism in single layers of VSe2 grown on graphite or MoS2 substrate has opened new opportunities to explore these ultrathin magnets for such applications. In this paper, we present a new type of magnetic sensor that utilizes the single layer VSe2 film as a highly sensitive magnetic core. The sensor relies in changes in resonance frequency of the LC circuit composed of a soft ferromagnetic microwire coil that contains the ferromagnetic VSe2 film subject to applied DC magnetic fields. We define sensitivity as the slope of the characteristic curve of our sensor, df0/dH, where f0 is the resonance frequency and H is the external magnetic field. The sensitivity of the sensor reaches a large value of 16×106Hz/Oe, making it a potential candidate for a wide range of magnetic sensing applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

A physical unclonable neutron sensor for nuclear arms control inspections

Abstract Classical sensor security relies on cryptographic algorithms executed on trusted hardware. This approach has significant shortcomings, however. Hardware can be manipulated, including below transistor level, and cryptographic keys are at risk of extraction attacks. A further weakness is that sensor media themselves are assumed to be trusted, and any authentication and encryption is done ex situ and a posteriori. Here we propose and demonstrate a different approach to sensor security that does not rely on classical cryptography and trusted electronics. We designed passive sensor media that inherently produce secure and trustworthy data, and whose honest and non-malicious nature can be easily established. As a proof-of-concept, we manufactured and characterized the properties of non-electronic, physical unclonable, optically complex media sensitive to neutrons for use in a high-security scenario: the inspection of a military facility to confirm the absence or presence of nuclear weapons and fissile materials.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

DOE OSTI2018

Wearable sweat sensors

© 2018 Macmillan Publishers Limited, Part of Springer Nature. All Rights Reserved. Sweat potentially contains a wealth of physiologically relevant information, but has traditionally been an underutilized resource for non-invasive health monitoring. Recent advances in wearable sweat sensors have overcome many of the historic drawbacks of sweat sensing and such sensors now offer methods of gleaning molecular-level insight into the dynamics of our bodies. Here we review key developments in sweat sensing technology. We highlight the potential value of sweat-based wearable sensors, examine state-of-The-Art devices and the requirements of the underlying components, and consider ways to tackle data integrity issues within these systems. We also discuss challenges and opportunities for wearable sweat sensors in the development of personalized healthcare.

Bariya, M↗