Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cementitious material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Initial Progress on Tank Bottom Repair for the DOE EM Tank Waste R&D Program - 25089

Several years prior to the Lab23-EM001 Call Announcement, Washington River Protection Solutions (WRPS) had done a review in identifying tank repair feasibility. [1, 2] The most viable methods of repair identified for the Floor of a Primary Tank identified were Grout Stabilization and Polymer Grout. Grout Stabilization was described as a self-leveling grout which fills the entire bottom of the tank and creates a new or false bottom. These types of materials have been used at the Savannah River Site (SRS) to fill and close waste tanks as well as contaminated spaces within decommissioned reactors. No mention was made as to the chemical composition of these Stabilizing Grouts in the review, however, grouts used at SRS for the mentioned applications have always been a cementitious grout material. A thickness of approximately 12 inches was suggested in the review. It was also suggested that an additional polymeric coating could be applied to this fresh and clean grout surface.

BLUE, KAREEN↗
DOE OSTI2021

Cement sensors with acoustic bandgaps using carbon nanotubes

Cement is widely used in wellbores to stabilize the steel casing used in wellbore operations for oil and gas production, enhanced geothermal systems and carbon sequestration, and to limit fluid movement between sub-surface strata. Flaws such as microcracks in wellbore cement can lead to leakage along the wellbore compromising wellbore integrity. There is an increasing need for methods to monitor cement crack propagation in wellbore environments. In this study, we develop and report the first cementitious sensors capable of exhibiting high frequency acoustic bandgaps (ABGs) using carbon nanotubes (CNTs). Computational simulations of a sensor unit cell are used to design cement-multi walled carbon nanotubes (MWCNTs) sensors that show a wide bandgap. When the cement-MWCNTs sensors is embedded in cement specimens, bandgaps were measured experimentally under 300 kHz and under 600 kHz, consistent with the computationally predicted bandgaps in the range of 290–360 kHz, 410–460 kHz and 515–585 kHz. These bandgap features were absent in homogeneous cement specimens. X-ray tomographic reconstructions showed microscopic debonding at cement-MWCNTs sensor interface. Frequency response analysis of a three-dimensional computational model indicated a shift of frequency of minimum transmission due to the interface debonding, but no perturbation of bandgap response was observed. Here, the cement-MWCNTs sensors developed in this study show the potential of a packed CNT inclusion material in cementitious matrix to create ABGs in a cement matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Determine the coordination of Al and Si of Fe-rich fly ash: The challenge in NMR and how we probe its heterogeneity using X-ray spectromicroscopy

Scanning transmission X-ray microscopy (STXM) coupled with ptychographic imaging at Al and Si K-edge is a new probe to the microscale chemistry of heterogenous materials. Here, the combined techniques are applied to study local coordination environment of Fe-rich fly ash (FA). Ptychographic imaging at Al K- and Si K-edge highlights the fine Al- and Si-rich morphological features, respectively, at 6 nm pixel resolution. STXM visualizes the inter- and intra-particle variations in the silicate polymerization degree and two types of Al coordination environment in FA. The Si K-edge of SiO4 connected with four-fold coordinated Al is higher than SiO4 sharing oxygen with six-fold coordinated Al. The result is consistent with bulk nuclear magnetic resonance spectroscopy measurement of the Fe-rich sample which, however, is sensitive to paramagnetic Fe and time-consuming. Here, we demonstrate that the combined method has great potential in the studies of chemically heterogenous aluminosilicates.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Reducing Pb and Cl Mobility in Waste-to-Energy Fly Ashes via Chlorellestadite Formation

Sustainably sourced development minerals are vital to meeting the demand for low-carbon construction materials. A potential waste material that can be a low-carbon construction material for cementitious systems is waste-to-energy fly ash (WTE ash), a by-product of waste incineration. WTE ash contains chloride-bearing species and heavy metals, which can promote steel reinforcement corrosion and present long-term leaching risks. Here, we present a new multi-step ash treatment protocol involving dissolution and heating to transform the non-readily removable chlorides in WTE ash to Chlorellestadite (Ca 10 (SiO 4 ) 3 (SO 4 ) 3 Cl 2 ). Our results suggest that this transformation significantly reduces chloride release from WTE ash in an alkaline cement-like environment by over two orders of magnitude, from 1500 mg/l to less than 10 mg/l. This transformation also significantly reduces Pb mobility after treatment (from > 5 mg/l to < 0.5 mg/l), likely caused by the crystallo-chemical incorporation of Pb in Chlorellestadite. In contrast to the existing ash treatment methods, the proposed ash treatment protocol minimizes heavy metals volatilization while simultaneously reducing Pb mobility and chloride release through Chlorellestadite formation. Furthermore, these findings overcome limitations preventing the commercial use of WTE ash and thus opening up pathways towards a circular economy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mercury sequestration in alkaline salt low-level radioactive waste

Liquid low-level radioactive waste at the Savannah River Site contains several species of mercury, including inorganic, elemental and methylmercury. This waste is solidified and stabilized in a cementitious waste form referred to as saltstone. Soluble mercury is stabilized as β-cinnabar, HgS as the result of reaction between the mercury and sulfur present in blast furnace slag, one of the cementitious regents. In this investigation, Mersorb®, a commercial granular activated carbon impregnated with sulfur, was evaluated as a pretreatment to remove mercury from the solution prior to cementation. Mersorb® was found to remove more than 96 mass percent of the methylmercury in simulated tank waste solution when the mass ratio of Mersorb® to mercury was above 2.5. Slag sequestered relatively more inorganic mercury than organic mercury in simulated tank waste after 24 hours of contact. This is likely due to the mercury-carbon bond being more covalent than the mercury-oxygen bond and therefore more difficult to break and slower to form HgS.

Cementitious Material↗
DOE OSTI2021

Chemistry of the interaction between an alkoxysilane-based impregnation treatment and cementitious phases

Chemical compatibility with a wide range of materials is among the features that has driven the use of alkoxysilanes as consolidants in built structures. Such compatibility is particularly important in cementitious materials where the reaction with portlandite may generate C-S-H gel, one of the main hydration phases of OPC. The cementitious matrix is a complex system, however, and the reaction of its many phases with alkoxysilanes, while poorly understood, may determine treatment efficacy. This article describes a detailed study of the individual interactions between an oligomeric alkoxysilane-based impregnation treatment previously shown to interact with the portlandite present in cement paste and the cementitious phases generated in ordinary portland cement hydration. The findings show that both portlandite and C-S-H gel interact with the silicon oligomers in the hydrolysed impregnation treatment to generate a C-S-H gel (in the case of portlandite) and a rise in C-S-H gel mean chain length (MCL). Ettringite is also altered in the presence of alkoxysilanes, transforming to gypsum and AH{sub 3}. Its transformation generates a tetrahedral aluminium that is taken up into a high silicon gel sourced from the treatment to form an amorphous aluminosilicate gel. Monocarboaluminate and katoite also partially decompose in the interaction with the product, whereas gibbsite remains unaffected.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development and Characterization of 3D-Printed Cementitious Sytems for Innovative Nuclear Systems

The Transformational Challenge Reactor (TCR) is being developed to demonstrate a revolutionary approach to deploying new nuclear power systems by building and operating an additively manufactured microreactor. This initiative provides a unique opportunity to investigate the possibility of taking advantage of the recent development of the 3D-printed concrete system using the Sky Big Area Additive Manufacturing (SkyBAAM) printer at the Manufacturing Demonstration Facility (MDF) at Oak Ridge National Laboratory. Two pathways have been pursued in parallel since the end of the second quarter of FY19: 1. Development of methods to characterize the performance of additive manufacturing concrete using traditional Portland-cement based solution, and 2. Investigation of the opportunity to develop innovation of printable materials with higher irradiation-resistance performance using nontraditional concrete solutions in favor of carbonated cementitious materials (CCMs). This report describes the results achieved to date for both pathways. The main results are listed below: 1. A test protocol has been established to characterize the fracture properties of 3D-printed concrete; this protocol will be used to assess the performance of printed traditional and nontraditional cementitious materials, with a focus on performance of the interfaces inherent to the additive manufacturing process. 2. A state-of-the-art review of the mechanisms, fabrication method, and performance of CCMs was conducted. CCMs appear to be a viable, highly innovative, more performant alternative to Portland-based cementitious solution for the erection of biological shield pending some materials development.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modular Processing of Flare Gas for Carbon Nanoproducts

This project demonstrated the technical viability and economic promise of a modular system for converting flared natural gas into valuable carbon nanoproducts (CNPs) through catalytic chemical vapor deposition (CVD). All major project milestones were successfully completed, including reactor design and commissioning, catalyst development, process optimization, technoeconomic analysis, and application testing in concrete systems. The overarching goal was to create a scalable, field-deployable process that valorizes stranded methane by producing high-value carbon materials for use in cementitious composites. At the lab scale, the team designed and built a fluidized bed reactor optimized for use with silica fume-supported nickel catalysts synthesized via atomic layer deposition (ALD). A statistically designed sintering study enabled precise tuning of nickel nanoparticle size, identifying the influence of oxygen partial pressure, time, and temperature on catalyst morphology and performance. These insights allowed the team to target catalyst conditions that maximize carbon nanofilament growth. Subsequent CVD experiments achieved up to 31.8 wt% carbon deposition under optimized conditions, with TEM confirming the presence of nanofilament structures and sustained hydrogen evolution during reaction. Reactor upgrades and empirical fluidization studies supported the development of reliable, repeatable experimental protocols. The modular pilot-scale skid reactor was fully constructed, instrumented, and commissioned. Capable of operating at 675–800°C and pressures up to 290 psig, the system was designed for continuous operation at a carbon production rate of 1 kg/hr. Initial demonstration runs confirmed solids handling, thermal control, and system leak-tightness, although a critical reactor component (the downfeed tube) was inadvertently omitted during final assembly. This omission limited gas–solid contact and prevented meaningful carbon deposition during pilot-scale CVD runs. Nonetheless, the system operated safely under design conditions, and the root cause of performance limitations was clearly identified. Complementary work on UHPC formulations demonstrated that small additions of carbon nanoproducts, including those derived from flare gas, can significantly enhance mechanical performance while preserving workability. A comprehensive study of CNF dispersion techniques and mix design optimization led to a clear protocol for integrating these nanomaterials into concrete. Incorporation of CNPs improved flexural toughness and reduced porosity, supporting their use in high-performance infrastructure applications. A technoeconomic analysis (TEA) confirmed that this process can produce CNP-loaded catalyst material at a levelized cost below $\$$7/kg across a range of catalyst loadings and reaction yields. With estimated market values for the carbon composite product ranging from $\$$14 to over $\$$60/kg, and the ability to blend CNPs into concrete at sub-percent levels with less than 10% added cost, the system presents a compelling economic case. While additional engineering work is needed to optimize fluidization and heat transfer at scale, this project establishes a strong foundation for commercial development. The process is not only technically sound but also economically promising, representing a viable pathway for flare gas mitigation through modular carbon nanomaterial production.

03 NATURAL GAS↗
DOE OSTI2020

Topological controls on aluminosilicate glass dissolution: Complexities induced in hyperalkaline aqueous environments

Abstract Fly ash, an aluminosilicate composite consisting of disordered (major) and crystalline (minor) compounds, is a low‐carbon alternative that can partially replace ordinary portland cement (OPC) in the binder fraction of concrete. Therefore, understanding the reactivity of fly ash in the hyperalkaline conditions prevalent in concrete is critical to predicting concrete's performance; including setting and strength gain. Herein, temporal measurements of the solution composition (using inductively coupled plasma‐optical emission spectrometry: ICP‐OES) are used to assess the aqueous dissolution rate of monophasic synthetic aluminosilicate glasses analogous to those present in technical fly ashes, under hyperalkaline conditions (10 ≤ pH ≤ 13) across a range of temperatures (25°C ≤ T≤45°C). The dissolution rate is shown to depend on the average number of topological constraints per atom within the glass network (n c , unitless), but this dependence weakens with increasing pH (>10). This is postulated to be on account of: (a) time‐dependent changes in the glass’ surface structure, that is, the number of topological constraints; and/or (b) a change in the dissolution mechanism (eg from network hydrolysis to transport control). The results indicate that the topological description of glass dissolution is most rigorously valid only at very short reaction times (ie at high undersaturations), especially under conditions of hyperalkalinity. These findings provide an improved basis to understand the underlying factors that affect the initial and ongoing reactivity of aluminosilicate glasses such as fly ash in changing chemical environments, for example, when such materials are utilized in cementitious composites.

Oey, Tandré↗
DOE OSTI2024

Alternative Pozzolans for Replacement of Fly Ash in Grout: Literature Review for Continuous Improvement of Cement Waste Forms

The Department of Energy (DOE) is currently responsible for treating radioactive and mixed waste, performing environmental restoration, and closing contaminated tanks and facilities resulting from nuclear weapons production during the Cold War. Cementitious reagents are the most widely used materials for (1) chemically stabilizing and encapsulating radionuclides and hazardous metals and (2) solidifying radioactive wastewater. Cementitious grouts and flowable concretes are also the most widely used materials for tank and facility closures and are used extensively for physical as well as chemical stabilization in environmental restoration projects. Ambient temperature radioactive waste cementation is a widely used technology for producing waste forms for final disposal. The current practice of designing and testing waste forms is based on a mid to late 20th century technology approach (i.e., materials, characterization, and test methods) for generating parameters for risk assessments. DOE technology development is needed to address both current, long-term, and emerging issues in this area as new waste streams come online and as regulations, performance knowledge, and risk assessment methodology continue to evolve. Consequently, the use of cementation as a means of treating chemically challenging radioactive liquid waste streams and reactive debris requires an enduring effort.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Ceramic–Metal (Cermet) Composites: A Review of Key Properties and Synthesis Methods Focused on Nuclear Waste Immobilization

Here this paper reviews key properties, applications, and examples of ceramic-metal composites (cermets), and metal matrix composites (MMC) with emphasis on their applicability as waste forms for immobilizing nuclear waste. While the literature is mature for vitrified and cementitious radioactive waste forms, cermet materials have not received adequate attention as potential candidates for immobilizing nuclear waste. To promulgate this effort, this review connects cermet and MMC design, such as hardened tools, with the chemistry of radioactive waste streams. A discussion on certification and qualification standards for cermet waste forms, literature gaps, and “how-to” sections on cermet processing techniques. Key parameters discussed include thermal conductivity, chemical durability, and waste loading, as well as examples for metal-containing waste forms. As cermet waste forms gain momentum within the community, this review paper aims ensure the end-of-life nuclear fuel cycle is addressed from a materials and waste disposition perspective.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Electromagnetic wave absorption of multifunctional cementitious composites incorporating polyvinyl alcohol (PVA) fibers and fly ash: Effects of microstructure and hydration

Highlights: • The cementitious composite shows excellent wide-band electromagnetic wave absorption in a frequency range of 2–18 GHz. • The PVA fibers and the fly ash change the dielectric properties of the cementitious composite by Debye polarization. • The iron oxide of the cementitious binders contributes to the magnetic properties of the composites. • The impacts of the microstructure and the hydration of the cementitious composite on its microwave absorption are analyzed. This paper devises a novel method for the adjustment of the pore structure and the hydration of cement to improve the electromagnetic wave absorption of the cementitious composites incorporating polyvinyl alcohol (PVA) fibers and fly ash in a frequency range of 2–18 GHz. The underlying mechanism of the absorption is investigated to explore the possibility of the structural and functional integration of these composites. The electromagnetic parameters of the prepared cementitious composites and those of the raw materials are analyzed in a frequency range of 0.5–18 GHz. Moreover, the pore structure and the chemical environment of the cementitious composites are examined by mercury intrusion porosimetry (MIP), back-scattered electron detector (BSE), and X-ray photoelectron spectroscopy (XPS). The results indicate that the PVA fibers and the high-volume fly ash have a positive effect on electromagnetic wave absorption of the cementitious composites through the adjustment of their pore structure and hydration.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Replacement of Fly Ash with Natural Pozzolans in Cementitious Waste Forms: Progress Report

The Department of Energy Environmental Management (DOE EM) Office is currently responsible for treating radioactive and mixed waste, environmental restoration, and closing contaminated tanks and facilities resulting from radioactive isotope production for defense applications during the Cold War. Cementitious reagents are the most widely used materials for (1) chemically stabilizing and encapsulating radionuclides and hazardous metals contaminated with radionuclides and Resource Conservation and Recovery Act (RCRA) hazardous metals and (2) solidifying radioactive and mixed wastewater for final disposal. Cementitious grouts and flowable concretes are also the most widely used materials for DOE waste tank and facility closures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites

Here, this paper studies the pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites. A hybrid approach was proposed by combining the advantages of traditional chemical-induced foaming (foaming approach) and lightweight particulate inclusions (synthetic foam approach). A comprehensive experimental program was conducted to evaluate the effects of foaming agents and fly ash cenosphere (FAC) on the printability, microstructure, mechanical and thermal properties of 3D printed samples. The results showed that the hybrid approach could produce a mixture with a density as low as 470 kg/m 3 while ensuring good flowability and buildability owing to the lubricating effect of foaming and supporting skeleton formed by FAC. In addition, a three-step homogenization procedure was also developed to predict the effective elastic modulus and thermal conductivity of 3D printable cementitious composites and cementitious foam. The findings of the study highlighted the effectiveness of the hybrid approach in formulating 3D printable ultra-lightweight cementitious composites in thermal insulation and acoustic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

LDR Inorganic Spiked Simulants in Pozzolan-Substituted Cast Stone for Hanford Pretreated Low-Activity Tank Waste

Pretreated Low Activity Waste (PTW/LAW) at the Hanford Site, is currently projected for disposition through a cementitious waste form. The current standard formulation, Cast Stone, uses Class F fly ash, blast furnace slag, and Portland cement. However, the future availability of Class F fly ash is uncertain, as many coal-fired power plants—the source of this byproduct—are being decommissioned or converted to natural gas. This issue has prompted research into identifying and evaluating suitable alternative materials to replace fly ash in the cementitious waste forms used by the Department of Energy (DOE). The Savannah River National Laboratory (SRNL) successfully identified four natural pozzolans for the replacement of Class F fly ash in the current Savannah River Site (SRS) low-level waste (LLW) form, Saltstone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗