Search NASA⌕ Search

SEARCH · Search NASA

Results for “Directional solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Directional Solidification of Eutectic Ceramics

Two major problems associated with structural ceramics are lack of damage tolerance and insufficient strength and creep resistance at very high temperatures of interest for aerospace application. This work demonstrated that the directionally solidified eutectics can have unique poly-phase microstructures and mechanical properties superior to either constituent alone. The constraining effect of unique eutectic microstructures result in higher resistance to slow crack growth and creep. Prospect of achieving superior properties through controlled solidification are presented and this technology can also be beneficial to produce new class of materials.

Sayir, Ali↗
NASA NTRS1988

Directional solidification of Cu-Pb and Bi-Ga monotectic alloys under normal gravity and during parabolic flight

Cu-Pb and Bi-Ga monotectic alloys of nominal hypermonotectic compositions were directionally solidified under various furnace translation rates, temperature gradients, and gravity levels. Gravity was varied by solidifying the alloys under ground conditions and in the furnace aboard NASA KC-135 aircraft, flying on parabolic trajectories. High translation rates, high gradients, high gravity levels, and higher density and lower thermal conductivity of the L2 phase favored the formation of fiber composite structure, while the opposite conditions resulted in structures consisting of L2 droplets in alpha matrix. A modified particle engulfment theory as originally enunciated by Ulhmann et al. (1964) is proposed to explain these observations.

Dhindaw, B. K.↗
NASA NTRS1983

Directional Solidification of Monotectic Alloys

Cooling at certain rates produced fibrous composite structures. Alloy samples melted in alumina or graphite crucibles under argon and then chillcast into 33-mm-diameter rods or sucked directly into 3-mm-bore alumina or silica tubes. Alloying not automatic with immiscible components of different densities and widely different melting points.

Hellawell, A.↗
NASA NTRS1999

Potential Flow Interactions With Directional Solidification

The effect of convective melt motion on the growth of morphological instabilities in crystal growth has been the focus of many studies in the past decade. While most of the efforts have been directed towards investigating the linear stability aspects, relatively little attention has been devoted to experimental and numerical studies. In a pure morphological case, when there is no flow, morphological changes in the solid-liquid interface are governed by heat conduction and solute distribution. Under the influence of a convective motion, both heat and solute are redistributed, thereby affecting the intrinsic morphological phenomenon. The overall effect of the convective motion could be either stabilizing or destabilizing. Recent investigations have predicted stabilization by a flow parallel to the interface. In the case of non-parallel flows, e.g., stagnation point flow, Brattkus and Davis have found a new flow-induced morphological instability that occurs at long wavelengths and also consists of waves propagating against the flow. Other studies have addressed the nonlinear aspects (Konstantinos and Brown, Wollkind and Segel)). In contrast to the earlier studies, our present investigation focuses on the effects of the potential flow fields typically encountered in Hele-Shaw cells. Such a Hele-Shaw cell can simulate a gravity-free environment in the sense that buoyancy-driven convection is largely suppressed, and hence negligible. Our interest lies both in analyzing the linear stability of the solidification process in the presence of potential flow fields, as well as in performing high-accuracy nonlinear simulations. Linear stability analysis can be performed for the flow configuration mentioned above. It is observed that a parallel potential flow is stabilizing and gives rise to waves traveling downstream. We have built a highly accurate numerical scheme which is validated at small amplitudes by comparing with the analytically predicted results for the pure morphological case. We have been able to observe nonlinear effects at larger times. Preliminary results for the case when flow is imposed also provide good validation at small amplitudes.

Buddhavarapu, Sudhir S.↗
NASA NTRS1980

Directional solidification at ultra-high thermal gradient

A high gradient controlled solidification (HGC) furnace was designed and operated at gradients up to 1800 C/cm to continuously produce aluminum alloys. Rubber '0' rings for the water cooling chamber were eliminated, while still maintaining water cooling directly onto the solidified metal. An HGC unit for high temperature ferrous alloys was also designed. Successful runs were made with cast iron, at thermal gradients up to 500 C/cm.

Flemings, M. C.↗
NASA NTRS1974

Radial and directional solidification of metallic systems in space

Investigation of the solidification behavior of spherical specimens of Ni-12 wt % Sn and Ni-1 wt % Ag that froze radially from the surface toward the center and cylindrical specimens of Al-33 wt % Cu eutectic that froze directionally under appropriately selected conditions of thermal gradient at the solid-liquid interface and growth rate. Possible effects of vacuum and low gravity conditions, under which the spherical specimens were processed, on observed nucleation and growth phenomena are discussed. A genetic explanation is given of observed microstructures, and the distributions of alloying elements is discussed. In directionally solidified eutectic specimens a comparison is made between statistically evaluated growth defects in Skylab and in ground specimens.

Katamis, T. Z.↗
NASA NTRS1984

Thermosolutal convection during directional solidification

During solidification of a binary alloy at constant velocity vertically upward, thermosolutal convection can occur if the solute rejected at the crystal-melt interface decreases the density of the melt. We assume that the crystal-melt interface remains planar and that the flow field is periodic in the horizontal direction. The time-dependent nonlinear differential equations for fluid flow, concentration, and temperature are solved numerically in two spatial dimensions for small Prandtl numbers and moderately large Schmidt numbers. For slow solidification velocities, the thermal field has an important stabilizing influence: near the onset of instability the flow is confined to the vicinity of the crystal-melt interface. Further, for slow velocities, as the concentration increases, the horizontal wavelength of the flow decreases rapidly - a phenomenon also indicated by linear stability analysis. The lateral inhomogeneity in solute concentration due to convection is obtained from the calculations. For a narrow range of solutal Rayleigh numbers and wavelengths, the flow is periodic in time.

Mcfadden, G. B.↗
NASA NTRS1980

Preparation of monotectic alloys having a controlled microstructure by directional solidification under dopant-induced interface breakdown

Monotectic alloys having aligned spherical particles of rods of the minor component dispersed in a matrix of the major component are prepared by forming a melt containing predetermined amounts of the major and minor components of a chosen monotectic system, providing in the melt a dopant capable of breaking down the liquid solid interface for the chosen alloy, and directionally solidfying the melt at a selected temperature gradient and a selected rate of movement of the liquid-solid interface (growth rate). Shaping of the minor component into spheres or rods and the spacing between them are controlled by the amount of dopant and the temperature gradient and growth rate values. Specific alloy systems include Al Bi, Al Pb and Zn Bi, using a transition element such as iron.

Parr, R. A.↗
NASA NTRS1986

Solar silicon from directional solidification of MG silicon produced via the silicon carbide route

A process of metallurgical grade (MG) silicon production is presented which appears particularly suitable for photovoltaic (PV) applications. The MG silicon is prepared in a 240 KVA, three electrode submerged arc furnace, starting from high grade quartz and high purity silicon carbide. The silicon smelted from the arc furnace was shown to be sufficiently pure to be directionally solidified to 10 to 15 kg. After grinding and acid leaching, had a material yield larger than 90%. With a MG silicon feedstock containing 3 ppmw B, 290 ppmw Fe, 190 ppmw Ti, and 170 ppmw Al, blended with 50% of off grade electronic grade (EG) silicon to reconduct the boron content to a concentration acceptable for solar cell fabrication, the 99% of deep level impurities were concentrated in the last 5% of the ingot. Quite remarkably this material has OCV values higher tham 540 mV and no appreciable shorts due to SiC particles.

Rustioni, M.↗
NASA NTRS1982

Heat flow control and segregation in directional solidification

Optimization of the vertical Bridgman technique for growth of electronic materials in single crystal form was investigated. The limitations of the crystal growth configuration were experimentally determined and heat transfer related deficiencies identified. Design of an alternate system was based on the use of heat pipes separated by a gradient region. Heat transfer analyses based on one and two dimensional models indicated the necessity of a flexible gradient zone configuration. Directional melting of binary systems as encountered during seeding in melt growth was analysed for concurrent compositional changes at the crystal-metal interface, and the theoretical treatment numerically applied to HgCdTe and Ga doped germanium. A theoretical and experimental study of the thermal effects associated with current flow was conducted. It was found that experimental measurements of dc induced growth during crystal pulling can be used for the precise determination of the Peltier coefficient.

Witt, A. F.↗
NASA NTRS1992

Directional solidification processing of alloys using an applied electric field

A method is provided for obtaining an alloy having an ordered microstructure which comprises the steps of heating the central portion of the alloy under uniform temperature so that it enters a liquid phase while the outer portions remain solid, applying a constant electric current through the alloy during the heating step, and solidifying the liquid central portion of the alloy by subjecting it to a temperature-gradient zone so that cooling occurs in a directional manner and at a given rate of speed while maintaining the application of the constant electric current through the alloy. The method is particularly suitable for use with nickel-based superalloys. The method of the present invention produces an alloy having superior characteristics such as reduced segregation. After subsequent precipitation by heat-treatment, the alloys produced by the present invention will have excellent strength and high-temperature resistance.

McKannan, Eugene C.↗
NASA NTRS1999

Directional Solidification of Bi-Sn on USMP-4

The experiments used MEPHISTO hardware to study the solidification and melting behavior of bismuth alloyed with 1 at% tin. Three samples, each approximately 900 mm long and 6mm in diameter, were used. A portion of each sample also included a 2 mm diameter growth capillary, to assist in the formation of a single grain. One sample provided the Seebeck voltage generated during melting and freezing processes. Another provided temperature data and Peltier pulsed demarcation of the interface shape for post flight analysis. The third sample provided resistance and growth velocity measurements, as well as additional thermal data. The third sample was also quenched at the end of the mission to preserve the composition of the liquid near the interface for post flight determination. A total of 450mm of directionally solidified samples were preserved for post mission structural and compositional characterization. Substantial differences were observed in the Seebeck signal between the ground-based experiments and the space-based experiments. The temperature gradient in the liquid for the ground-based experiments was significantly lower than the temperature gradient in the liquid for the space-based experiments.

Abbaschian, Reza↗
NASA NTRS1972

Directional solidification of eutectic composites in space environment

The Ni-Ni3Ta eutectic and a nickel-base alloy containing 30 wt pct Ta were solidified unidirectionally in an electron beam floating zone melting apparatus. It was found that the volume fraction of the Ni3Ta phase in the Ni-Ni3Ta eutectic mixture was increased from 7.6 to 36 volume pct in agreement with the theory as predicted. Tensile properties of the randomly solidified and unidirectionally solidified Ni-Ni3Ta eutectic were determined as function of solidification rate and temperature. It was found that the ultimate tensile strength decreased as both the test temperature and solidification rate increased. An elongation of 40 pct was obtained for a nickelbase alloy containing 30 wt at room temperature. This unusually large elongation was attributed to the superplastic behavior of the alloy. The critical currents versus the external fields at 2.5, 3.0, 3.5 and 4.2 deg for the unidirectionally solidified Pb-Sn eutectic were measured. The values of critical fields at zero critical currents were obtained by extrapolation.

Yue, A. S.↗
NASA NTRS1981

Automated directional solidification system for space processing

The system is to be used under low gravity conditions aboard a sounding rocket. Two complete flight qualified units, each of which includes four individually controllable furnaces capable of operation to as high as 1600 C, were developed with operating and control panels, associated cables, tools, and some spare supplies. Drawings, operating manuals, a user's computer program and reports and papers describing the work and equipment are presented.

Mccreight, L. R.↗
NASA NTRS1985

Heat Flow and Segregation in Directional Solidification

This research is composed of three major components: (1) development of interface morphology control for automated Bridgman growth of semiconductor systems; (2) comparative analysis of segregation during crystal growth in a reduced gravity environment and in the presence of magnetic fields; and (3) consequences of seeding by meltback in Bridgman growth under reduced gravity conditions. In attempts to optimize furnace design for crystal growth in a reduced gravity environment, an analytical approach to heat transfer was developed. It was thus found that charge confining crucibles diminish the ability to control the growth interface morphology through its position within the gradient zone. A heat pipe hot zone system for Bridgman growth, in reduced gravity environment, of crystal with diameters up to 16 mm was developed. For growth of Ga-doped germanium in the multipurpose (ASTP) furnace, it was found that the application of transverse magnetic fields (up to 36 kg) does not substantially increase the effective distribution coefficient; i.e., diffusion-controlled segregation observed in reduced gravity environment cannot be reached nor approached by magnetic field induced melt stabilization.

Witt, A. F.↗
NASA NTRS1985

Directional Solidification of Monotectic and Hypermonotectic Aluminum-indium Alloys Under Micron-g

The objective of this program is to analyze the mechanisms involved in the composite solid structure formation obtained from a miscibility gap alloy under microgravity. The metallic system aluminum-indium was chosen for its low critical temperature, broad miscibility gap, and rather well-known thermodynamic properties. The experiment was performed aboard the Salyut-7 spacecraft. The theories of capture of particulates by an advancing front were not able to explain the observations made on SPAR and Salyut-7 experiments. A new model was developed based on the filtration theory considering the globules population: the solid/liquid interface is like a filter of negligible thickness for the globules and its efficiency is limited by a pressure barrier measured for Al-In alloys by ground based experiments. The Materials Experiment Assembly (MEA)-3 experiment was consequently adjusted to take into account the new model. The behavior of the globules in an interacting population on the solid front is, of course, an essential factor in the theory. The theory is at present being completed by results obtained by the Laboratoire d'Aerothermique of Meudon. The hydrodynamic and thermal interactions between pairs of globules placed in a temperature gradient have been calculated showing a large reduction of the Marangoni effect compared to the isolated globule. Physico-chemical properties of metallic liquid interface are currently being investigated.

Potard, C.↗