Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Auxin asymmetry during gravitropism by tomato hypocotyls

Gravitropic asymmetry of auxin was observed in hypocotyls of tomato (Lycopersicon esculentum Mill.) soon after horizontal placement: the ratio of apically supplied [3H]IAA collected from the lower sides to that from the upper sides was about 1.4 between 5 and 10 minutes. This was adequately early to account for the beginning of curvature. The auxin asymmetry ratio rose to about 2.5 between 20 and 25 minutes, and to 3.5 during the main phase of curvature. This compares reasonably well with the roughly 3.9 ratio for elongation on the lower side to elongation on the upper side that is the basis for the curvature. These data extend evidence that the Went-Cholodny theory for the mediation of tropisms is valid for dicot stems. Also consistent with the theory, an auxin asymmetry ratio of 2.5 was observed when wrong-way gravitropic curvature developed following application of a high level of auxin. In addition to reversing the asymmetry of elongation, the large supplement of auxin resulted in lower net elongation. Previous data established that ethylene is not involved in this decrease of growth as a function of increasing level of auxin.

NASA Program Space Biology↗
NASA NTRS1991

Graviresponsiveness of surgically altered primary roots of Zea mays

We examined the gravitropic responses of surgically altered primary roots of Zea mays to determine the route by which gravitropic inhibitors move from the root tip to the elongating zone. Horizontally oriented roots, from which a 1-mm-wide girdle of epidermis plus 2-10 layers of cortex were removed from the apex of the elongating zone, curve downward. However, curvature occurred only apical to the girdle. Filling the girdle with mucilage-like material transmits curvature beyond the girdle. Vertically oriented roots with a half-girdle' (i.e. the epidermis and 2-10 layers of the cortex removed from half of the circumference of the apex of the elongating zone) curve away from the girdle. Inserting the half-girdle at the base of the elongating zone induces curvature towards the girdle. Filling the half-circumference girdles with mucilage-like material reduced curvature significantly. Stripping the epidermis and outer 2-5 layers of cortex from the terminal 1.5 cm of one side of a primary root induces curvature towards the cut, irrespective of the root's orientation to gravity. This effect is not due to desiccation since treated roots submerged in water also curved towards their cut surface. Coating a root's cut surface with a mucilage-like substance minimizes curvature. These results suggest that the outer cell-layers of the root, especially the epidermis, play an important role in root gravicurvature, and the gravitropic signals emanating from the root tip can move apoplastically through mucilage.

Non-NASA Center↗
NASA NTRS1984

Analysis and significance of gravity-induced asymmetric growth in the grass leaf-sheath pulvinus

The negative gravitropic response in the grass leaf-sheath pulvinus is a consequence of cell elongation involving all cells except those of the uppermost region of the upper flank of an horizontally oriented pulvinus. The lowermost layer of cells elongate maximally, and the regions in between elongate to intermediate extents. The resulting curvatures of a responding pulvinus can be expressed mathematically by relating the angle of curvature (theta) to the original length (L0) and the maximal length of the lower surface (L1) and the diameter of the organ (D), using the equation, theta = (L1-L0)/D, where theta is in radians. The elongation response (S) of any individual cells within the pulvinus can be expressed by the equation, S = 0.5 - r cos theta, where r is the radius of the pulvinus and theta is in degrees. Microscopic measurement of cell lengths in different regions of the pulvinus supports the mathematical predictions. Indirect support is also obtained from the use of colchicine, coumarin, dichlorobenzonitrile (DCBN) and isopropyl N-chlorophenyl carbamate which exaggerate the inherent asymmetry during gravitropic response. Coumarin and DCBN also induce thickenings in the radial walls which appear first in the statenchyma, and later, in cells located towards the outer periphery of the pulvinus. The distribution patterns of these thickenings suggest that the asymmetric growth response of the pulvinus may be due to a differential and radial, centrifugal transport of growth promotors from the central statenchyma region.

Plant Epidermis/cytology/growth & development↗
NASA NTRS2009

Adaptive Morphological Feature-Based Object Classifier for a Color Imaging System

Utilizing a Compact Color Microscope Imaging System (CCMIS), a unique algorithm has been developed that combines human intelligence along with machine vision techniques to produce an autonomous microscope tool for biomedical, industrial, and space applications. This technique is based on an adaptive, morphological, feature-based mapping function comprising 24 mutually inclusive feature metrics that are used to determine the metrics for complex cell/objects derived from color image analysis. Some of the features include: Area (total numbers of non-background pixels inside and including the perimeter), Bounding Box (smallest rectangle that bounds and object), centerX (x-coordinate of intensity-weighted, center-of-mass of an entire object or multi-object blob), centerY (y-coordinate of intensity-weighted, center-of-mass, of an entire object or multi-object blob), Circumference (a measure of circumference that takes into account whether neighboring pixels are diagonal, which is a longer distance than horizontally or vertically joined pixels), . Elongation (measure of particle elongation given as a number between 0 and 1. If equal to 1, the particle bounding box is square. As the elongation decreases from 1, the particle becomes more elongated), . Ext_vector (extremal vector), . Major Axis (the length of a major axis of a smallest ellipse encompassing an object), . Minor Axis (the length of a minor axis of a smallest ellipse encompassing an object), . Partial (indicates if the particle extends beyond the field of view), . Perimeter Points (points that make up a particle perimeter), . Roundness [(4(pi) x area)/perimeter(squared)) the result is a measure of object roundness, or compactness, given as a value between 0 and 1. The greater the ratio, the rounder the object.], . Thin in center (determines if an object becomes thin in the center, (figure-eight-shaped), . Theta (orientation of the major axis), . Smoothness and color metrics for each component (red, green, blue) the minimum, maximum, average, and standard deviation within the particle are tracked. These metrics can be used for autonomous analysis of color images from a microscope, video camera, or digital, still image. It can also automatically identify tumor morphology of stained images and has been used to detect stained cell phenomena (see figure).

McDowell, Mark↗
NASA NTRS2024

Effects of Oxide Dispersion on Failure Modes in an Additively Manufactured Superalloy

Additive manufacturing opens new paths for introducing oxide particles into superalloys, to potentially provide oxide dispersion strengthening (ODS) at high temperatures. This provides opportunities to study how such dispersions can influence failure modes for a given superalloy, after nearly identical material processing paths. The objective of this study was to compare monotonic failure modes for additively manufactured superalloys with versus without an introduced oxide dispersion. The superalloy for each case was produced by laser powder bed fusion additive manufacturing. Specimens were subsequently given consistent thermal treatment paths and then tested in tensile and creep tests at varied temperatures. Failure modes were then compared. Additively manufactured NiCrAl without ODS had randomly oriented equiaxed grains while this alloy with 0.25 wt% Y 2 O 3 ODS additions had elongated [001] oriented grains in the build direction. Material made without ODS (“No-ODS”) was nearly completely single phase gamma, while ODS additions resulted in gamma, chromium carbide, and Y-Al-Cr oxide phases, with carbide and oxide phases contents estimated at no more than 13 and 1 vol%, respectively. Compared to No-ODS, material made with ODS had higher tensile strengths at room, 760 and 1093 °C. The elongation of ODS material was lower than No-ODS at room temperature, but higher at 760 °C. At 1093 °C ODS material had higher elongation than No-ODS when tested in the build direction, however elongation was lower for ODS material in the transverse direction at 1093 °C. Creep rupture strain, life, and area reduction at 760 and 1093 °C were all much higher for ODS material compared to No-ODS; 760 °C rupture life was nearly 100 times longer for ODS material. The presence of Y in the ODS material significantly improved oxidation resistance.

supperalloys↗
NASA NTRS2026

Comparison Testing and Analysis of Braided Cords Constructed from Varying Kevlar Fiber Types

Material advancements move quickly, resulting in material obsolescence issues that require parachute engineers to understand how the material properties change with a material upgrade and if there are expected impacts to overall performance of the parachute. The objective of this test was to measure the elongation of different Kevlar types at both the cord-level and at the yarn-level to determine if a change in Kevlar type impacted parachute performance. An Instron machine with a pin-to-pin connection was used to measure load and displacement time histories for various Kevlar cord and yarn samples in a cyclic load profile. Twenty-four cord samples and twenty-four yarn samples were tested; each sample was cycled five times to the relevant maximum load (either to breaking strength or to the 30% peak load expected in flight). In addition to the Instron measurements, a photogrammetric technique was also implemented to measure elongation of the samples using button targets. Modulus test data shows approximately a 10% difference in elongation between Kevlar 29AP and Kevlar 129, and another 10% difference in elongation between Kevlar 29 and Kevlar 29AP. Although this is a measurable change in modulus, the effect on parachute performance is likely small, particularly for non-primary structure elements of relatively small length. This test campaign provides an example of the type of testing and analysis that parachute engineers could do to understand how material upgrades affect performance of their systems.

Parachutes↗
NASA NTRS2026

Comparison Testing and Analysis of Braided Cords Constructed from Varying Kevlar Fiber Types

Material advancements move quickly, resulting in material obsolescence issues that require parachute engineers to understand how the material properties change with a material upgrade and if there are expected impacts to overall performance of the parachute. The objective of this test was to measure the elongation of different Kevlar types at both the cord-level and at the yarn-level to determine if a change in Kevlar type impacted parachute performance. An Instron machine with a pin-to-pin connection was used to measure load and displacement time histories for various Kevlar cord and yarn samples in a cyclic load profile. Twenty-four cord samples and twenty-four yarn samples were tested; each sample was cycled five times to the relevant maximum load (either to breaking strength or to the 30% peak load expected in flight). In addition to the Instron measurements, a photogrammetric technique was also implemented to measure elongation of the samples using button targets. Modulus test data shows approximately a 10% difference in elongation between Kevlar 29AP and Kevlar 129, and another 10% difference in elongation between Kevlar 29 and Kevlar 29AP. Although this is a measurable change in modulus, the effect on parachute performance is likely small, particularly for non-primary structure elements of relatively small length. This test campaign provides an example of the type of testing and analysis that parachute engineers could do to understand how material upgrades affect performance of their systems.

Modulus Testing↗
NASA NTRS1972

Solar corona photography, part B

Photographic observations of the solar corona by the Apollo 16 command module pilot while in lunar orbit are reported. These were designed to provide data on outer coronal forms and intensities to elongation angles of 25 deg. The results of Apollo 15 solar corona photography verified the procedures and provided the first photographs of identifiable coronal streamers curving at elongation angles of some 10 deg. By using the Apollo 15 data, exposure settings were optimized for Apollo 16, and the results show a significant improvement in photometric quality over the large range of brightness to be photographed. Ground observations of the inner solar corona (to approximately 2 solar radii from Sun center) indicate a general lack of coronal structure, and results of data reduction thus far show no streamer structure at large elongation angles.

Macqueen, R. M.↗
NASA NTRS1978

Molded composite pyrogen igniter for rocket motors

A lightweight pyrogen igniter assembly including an elongated molded plastic tube adapted to contain a pyrogen charge was designed for insertion into a rocket motor casing for ignition of the rocket motor charge. A molded plastic closure cap provided for the elongated tube includes an ignition charge for igniting the pyrogen charge and an electrically actuated ignition squib for igniting the ignition charge. The ignition charge is contained within a portion of the closure cap, and it is retained therein by a noncorrosive ignition pellet retainer or screen which is adapted to rest on a shoulder of the elongated tube when the closure cap and tube are assembled together. A circumferentially disposed metal ring is provided along the external circumference of the closure cap and is molded or captured within the plastic cap in the molding process to provide, along with O-ring seals, a leakproof rotary joint.

Heier, W. C.↗
NASA NTRS1977

On the photometric axis of the zodiacal light

A model of the zodiacal cloud is used to predict the position of the photometric axis (the locus of points of maximum brightness) of the zodiacal light at any elongation angle from the sun for any time of the year for various symmetry planes: the orbital planes of Venus, Mars, and Jupiter, the invariable plane, and the solar equatorial plane. Using a scattering function which combines isotropic scattering and Fresnel reflection, the geocentric distance of the dust that contributes most of the brightness at each elongation angle is determined by computing the brightness contribution along the line of sight. A comparison of the predicted and observed positions shows that at elongation angles of 15 to 60 deg, the axis of symmetry appears to be close to the orbital plane of Venus. At angles of less than 10 deg, it is difficult to distinguish among the proposed planes of symmetry. Observations of the photometric axis at angles of 60 to 180 deg are scarce and do not permit precise determination of the axis of symmetry in that region.

Misconi, N. Y.↗
NASA NTRS1982

Gravity perception and asymmetric growth in plants - A model derived from the grass pulvinus

It is pointed out that gravitropic responses in plants involve asymmetric growth. On the basis of the geometry of growth response in grass leaf sheath pulvinus, a general model is proposed for gravitropism in multicellular plant organs. The negative gravitropic response of a pulvinus is a result of cell elongation involving all but the uppermost region of a horizontally placed organ. Whereas the uppermost region does not grow, the lowermost region elongates maximally. The regions between elongate to intermediate extents. An expression is given relating the angle of curvature of the organ to the diameter and initial and final lengths of the organ. It is shown that the response of the individual cells can be expressed as inherent sensitivity to gravitational stimulus according to a particular equation.

Dayanandan, P.↗
NASA NTRS1984

Calcium elicited asymmetric auxin transport in gravity influenced root segments

Auxin is a prime candidate for regulating and modulating the differential growth response of primary corn roots to gravity. Auxin, indole-3-acetic acid (IAA), both promotes and inhibits root elongation rapidly within a narrow concentration range. Thus growth regulation would require only small changes in the short lag period for initiation of gravitropism. Since auxin is transported to/through the zone of elongation toward the meristem, it may serve as a direct communication link between the zone of elongation, site of gravitropic response, and the root cap (RC), site of gravity perception. When auxin transport is inhibited, gravitropism is also inhibited. Napthylpthalamic acid (NPA) is one such inhibitor. It inhibits gravitropism only when applied to the apical growing and dividing region of the root. Application at the basal end of the root does not influence gravitropic NPA causes upward curvature when applied to the upper surface of horizontal, two day-old, intact corn roots. This effect is countered by application of IAA to the opposite side.

Edwards, K. L.↗
NASA NTRS1984

An atomistic model of slip formation

The results of an atomistic model for the simulation of the early stages of crack initiation in a two-dimensional triangular lattice are presented. In the current model, each particle in the system is treated discretely and assumed to be interacting with the surrounding particles via Lennard-Jones potentials. A uniaxial load (in incremental elongations) is applied to the rectangular two-dimensional slab in either the x or the y direction. After each incremental elongation the system is equilibrated using a static method. Initially, elastic behavior in the x and y directions is observed. Continued elongation results in plastic deformation. In lattices with point defects, the defects first move to the surface, creating vacancies which trigger plastic deformation.

Halicioglu, T.↗
NASA NTRS1988

Arcs from gravitational lensing

The proposal made by Paczynski (1987) that the arcs of blue light found recently in two cluster cores are gravitationally lensed elongated images of background galaxies is investigated. It is shown that lenses that are circularly symmetric in projection produce pairs of arcs, in conflict with the observations. However, more realistic asymmetric lenses produce single arcs, which can become as elongated as the observed ones whenever the background galaxy is located on or close to a cusp caustic. Detailed computer simulations of lensing by clusters using a reasonable model of the mass distribution are presented. Elongated and curved lensed images longer than 10 arcsec occur in 12 percent of the simulated clusters. It is concluded that the lensing hypothesis must be taken seriously.

Grossman, Scott A.↗
NASA NTRS1989

Comments on comet shapes and aggregation processes

An important question for a comet mission is whether comet nuclei preserve information clarifying aggregation processes of planetary matter. New observational evidence shows that Trojan asteroids, as a group, display a higher fraction of highly-elongated objects than the belt. More recently evidence has accumulated that comet nuclei, as a group, also display highly-elongated shapes at macro-scale. This evidence comes from the several comets whose nuclear lightcurves or shapes have been well studied. Trojans and comet nuclei share other properties. Both groups have extremely low albedos and reddish-to neutral-black colors typical of asteroids of spectral class D, P, and C. Both groups may have had relatively low collision frequencies. An important problem to resolve with spacecraft imaging is whether these elongated shapes are primordial, or due to evolution of the objects. Two hypotheses that might be tested by a combination of global-scale and close-up imaging from various directions are: (1) The irregular shapes are primordial and related to the fact that these bodies have had lower collision frequencies than belt asteroids; or (2) The irregular shapes may be due to volatile loss.

Hartmann, William K.↗
NASA NTRS1990

Comet nuclei and Trojan asteroids - A new link and a possible mechanism for comet splittings

Relatively elongated shapes, implied by recent evidence of a greater incidence of high amplitude lightcurves for comet nuclei and Trojan asteroids than for similarly scaled main belt asteroids, are suggested to have evolved among comet nuclei and Trojans due to volatile loss. It is further suggested that such an evolutionary course may account for observed comet splitting; rotational splitting may specifically occur as a result of evolution in the direction of an elongated shape through sublimation. Supporting these hypotheses, the few m/sec separation velocities projected for rotationally splitting elongated nuclei are precisely in the observed range.

Hartmann, William K.↗
NASA NTRS1991

Mechanical properties of 2D and 3D braided textile composites

The purpose of this research was to determine the mechanical properties of 2D and 3D braided textile composite materials. Specifically, those designed for tension or shear loading were tested under static loading to failure to investigate the effects of braiding. The overall goal of the work was to provide a structural designer with an idea of how textile composites perform under typical loading conditions. From test results for unnotched tension, it was determined that the 2D is stronger, stiffer, and has higher elongation to failure than the 3D. It was also found that the polyetherether ketone (PEEK) resin system was stronger, stiffer, and had higher elongation at failure than the resin transfer molding (RTM) epoxy. Open hole tension tests showed that PEEK resin is more notch sensitive than RTM epoxy. Of greater significance, it was found that the 3D is less notch sensitive than the 2D. Unnotched compression tests indicated, as did the tension tests, that the 2D is stronger, stiffer, and has higher elongation at failure than the RTM epoxy. The most encouraging results were from compression after impact. The 3D braided composite showed a compression after impact failure stress equal to 92 percent of the unimpacted specimen. The 2D braided composite failed at about 67 percent of the unimpacted specimen. Higher damage tolerance is observed in textiles over conventional composite materials. This is observed in the results, especially in the 3D braided materials.

Norman, Timothy L.↗
NASA NTRS1992

Electrorepulsive actuator

The invention is a linear actuator that operates under the principle that like charges repel and opposite charges attract. The linear actuator consists of first and second pairs of spaced opposed conductors where one member of each pair of conductors is attached to a fixed member, and where the other member of each pair of conductors is attached to a movable member such as an elongated rod. The two pairs of spaced conductors may be provided in the form of two spacedly interwound helical vanes where the conductors are located on the opposite sides of the two helical vanes. One helical vane extends inwardly from a housing and the other helical vane extends outwardly from an elongated rod. The elongated rod may be caused to move linearly with respect to the housing by applying appropriate charges of like or opposite polarity to the electrical conductors on the helical vanes.

Collins, Earl R., Jr.↗