Search NASA⌕ Search

SEARCH · Search NASA

Results for “Zirconia”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effects of bridging fibers on the evolution of lamellar architecture during H 2 /H 2 O redox cycling of Fe-foams

Fe/Fe 3 O 4 redox cycling via cyclic H 2 /H 2 O exposure at 800 °C is studied in lamellar Fe foams with 15 vol% fibers, created by freeze-casting. Fibers were integrated in the foams to mitigate densification during cycling by mechanically supporting neighboring lamellae, thus preventing buckling and sintering at contact points. Three fiber types are examined: short (0.1 mm) and long (1–2 mm) stainless-steel fibers, and long zirconia fibers. Long fibers bridge lamellae and have a marked effect on the architecture by increasing the initial interlamellar porosity (from < 60 to > 85%), with a corresponding decrease in foam shrinkage during initial reduction and sintering (from > 80 to < 55% volumetric loss). Though performance improves as compared to fiber-free foams, fiber effectiveness against damage decreases with cycling: after 10 redox cycles, porosity falls from 85 to 50% for foams with long fibers. One novel degradation mechanism is identified: fiber engulfment. This mechanism occurs over successive redox cycles, as material from the lamellae cyclically engulfs (as Fe 3 O 4 ) and withdraws (as Fe) from the fibers, with a net transport from lamellae to fibers after each cycle. Finally, this cyclic coarsening mechanism alters foam architecture from bridged-lamellar (with evenly distributed porosity) to mixed lamellar/fibrous (with unevenly distributed porosity).

36 MATERIALS SCIENCE↗
DOE OSTI2022

A general strategy and a consolidated mechanism for low-methane hydrogenolysis of polyethylene over ruthenium

Polyethylene (PE) is one of the most environment-threatening plastic waste. Its Ru-catalyzed hydrogenolysis is rapid but produces too much methane. Here, in this study, low-density PE hydrogenolysis is performed at mild conditions and short times over Ru-doped zirconia catalysts (Ru-XZr, X = Ti, Nb, Ce, W, V, Mo, Fe) to determine low-methane catalysts. Methane is produced via direct terminal C-C scission and surface cascade of consecutive C-C scissions, with the latter sensitive to hydrogen availability and dominant in hydrogen-lean conditions. Reactivity studies, characterization and theory reveal that the most effective dopant oxides (W, V, and Mo) are intermediately reducible, as they store and supply extra hydrogen to Ru via reverse hydrogen spillover. This hydrogen readily hydrogenates and desorbs long alkyl surface intermediates that would otherwise produce cascade methane. Our proposed mechanism reconciles the low methane production achieved by increasing the hydrogen pressure or reducing the particle size and exposes the key selectivity descriptors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enhanced NO, CO and C 3 H 6 conversion on Pt/Pd catalysts: Impact of oxygen storage material and catalyst architecture

Simultaneous conversion of NO, CO and C 3 H 6 under stoichiometric conditions was carried out on washcoated monoliths containing oxygen storage material (OSM)-promoted mixed Platinum group metals (PGM: Pt(95 %)/Pd(5 %)), to evaluate OSM promotion and to identify the best architecture. The studied OSMs include ceria-zirconia (Ce 0.3 Zr 0.7 O 2 ; CZO) and mixed metal oxide spinel (Mn 0.5 Fe 2.5 O 4 ; MFO). PGM supported directly on the OSM was found to be the best design for CZO, leading to a ~70 °C simultaneous decrease in the light-off temperature (T 80 ; feed temperature giving 80 % conversion) for NO, CO and C 3 H 6 conversion compared to the alumina-supported PGM. Close coupling between the PGM and CZO is responsible for the activity promotion. In contrast, a dual-layer architecture (top PGM layer, bottom MFO layer) outperformed the MFO-supported PGM catalyst. The dual-layer PGM-MFO catalyst decreased the T 80 by ~50 °C for NO, CO and C 3 H 6 conversion compared to the PGM-only catalyst. Enhancement obtained with the dual-layer PGM-MFO architecture relies on a direct catalytic contribution from the spinel. During lean/rich modulation the addition of CZO or spinel helps to mitigate the detrimental impact of modulation on NO, CO and C 3 H 6 conversion above 400 °C. The data suggest that both CZO and MFO can buffer lean/rich modulation but exhibit preference to different reductants; CZO-supported PGM and dual-layer PGM-MFO show no conversion decrease during modulation for CO or C 3 H 6 modulation, respectively. Dynamic oxygen storage capacity (DOSC) measurements show that the spinel exhibits ~10 times higher DOSC than CZO for both CO and C 3 H 6 reductants. Both CO and C 3 H 6 are equally effective reductants for the MFO but CO is better for CZO and PGM-deposited CZO. The study provides useful insight into benefits of OSM and provides guidance for optimization of the multi-component PGM + OSM catalyst composition and architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Highly efficient Pt catalyst on newly designed CeO 2 -ZrO 2 -Al 2 O 3 support for catalytic removal of pollutants from vehicle exhaust

Pt-CeO 2 catalysts have been widely studied for the vehicle emission control. Designing novel CeO 2 based supports with improved physical-chemical properties has become a research hotspot to further promote the catalytic performance and stability of Pt-CeO 2 catalysts. In this work, through utilizing a unique, two-step incipient wetness impregnation (T-IWI) method for ceria-zirconia-alumina (CZA-T) support preparation, a Pt single site catalyst (Pt/CZA-T) with excellent thermal stability was synthesized. Higher oxidation activity and Oxygen storage capacity (OSC) were achieved on activated Pt/CZA-T, comparing to Pt catalysts on regular CeO 2 /Al 2 O 3 (Pt/CA) and one-step prepared CeZrO x /Al 2 O 3 (Pt/CZA). Via the modification of hydrophilic/hydrophobic properties of γ-Al 2 O 3 by this unique T-IWI method, finer Ce 0.9 Zr 0.1 O 2 particles with higher density of surface defects were formed on CZA-T, on which a higher Pt dispersion and stronger Pt-O-Ce interaction were achieved. Upon activation, smaller, well-dispersed Pt clusters on CZA-T were generated. It was concluded that the CO oxidation performance and OSC were highly related to the size of Pt clusters on different supports that we have developed. Finally, more Pt sites located at Pt cluster-CeZrO x interfaces, which were the real active sites, were responsible for the highest OSC function and CO oxidation activity of activated Pt/CZA-T catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Processing and characterization of the homologous Zr x Ta 2 O 2x+5 series

In this study, Zr x Ta 2 O 2x+5 (ZTOx) was systematically studied to determine ideal solid-state synthesis and pressureless sintering conditions. For Zr 6 Ta 2 O 17 (ZTO6) and other compositions with values of x in ZTOx the optimal synthesis temperature of 1100 °C with 1 h dwell time was optimal. XRD phase analysis of the homologous series indicated that for ZTOx, x = 5, 6, 7, and 8 were within the phase stability field while x = 4 and x = 9 were outside the phase stability field. Unit cell lattice parameters changed anisotropically with Zr:Ta ratio with an overall <0.1% change in unit cell volume across the solid solution. Some Raman modes red shifted while others blue shifted, indicating competing tensile and compressive strains. Sintering of ZTOx required a progressively higher temperature as Zr-content increased despite the same starting powder grain sizes and synthesis temperature. Higher Vickers hardness for Zr-rich (12.7–12.8 GPa) than Ta-rich Zr x Ta 2 O 2x+5 (11.6–11.7 GPa) disappeared when accounting for different sintering temperatures. Indentation toughness was similar for all compositions (1.2–1.4 MPa m 1/2 ). Properties of Zr x Ta 2 O 2x+5 series indicate tunability of Zr:Ta composition ratio while maintaining the structure and room temperature mechanical properties comparable to Hf 6 Ta 2 O 17 and 8 mol% yttria stabilized zirconia ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Palm oil deoxygenation with glycerol as a hydrogen donor for renewable fuel production using nickel-molybdenum catalysts: The effect of support

Palm oil, one of the most widely used vegetable oils, offers significant potential as a sustainable feedstock for biofuel production. This study explores the deoxygenation of palm oil using glycerol as a hydrogen donor, with nickel-molybdenum (NiMo) catalysts supported on commercial alumina (Al 2 O 3 ), and zeolite (HZSM-5) comparing with self-prepared zirconia (ZrO 2 ). The catalysts were synthesized via incipient wetness impregnation and evaluated for their performance in biofuel production. NiMo/Al 2 O 3 exhibited the lowest oxygen removal efficiency (68.5 %), while NiMo/HZSM-5 achieved a higher oxygen removal (74.3 %) but also demonstrated the highest coke formation. The type of support material influenced the resulting biofuel range, with NiMo/HZSM-5 and NiMo/ZrO 2 favoring jet fuel production, whereas NiMo/Al 2 O 3 was more suitable for diesel production. Notably, NiMo/ZrO 2 exhibited the highest performance in palm oil deoxygenation while minimizing coke formation. These findings highlight NiMo/ZrO 2 as a promising catalyst for efficient and stable biofuel production, with the support material significantly influencing product yield and fuel quality.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗
DOE OSTI2022

Phase-field modeling of crack growth and mitigation in solid oxide cells

Fracture and crack growth is one of the main degradation mechanisms in solid oxide cells (SOCs). However, the modeling of crack growth in SOCs is challenging due to their complex microstructures and possible plasticity development within the Ni particles in Ni-based SOC electrodes. In this study, a phase-field fracture model is developed, which incorporates the SOC microstructures and phase-dependent material properties, including yield strength, fracture toughness in the bulk and at the interphase boundaries. The model is employed to study crack initiation and growth under thermal and redox cycling on the hydrogen electrode side of SOCs. The simulation results demonstrate that under thermal cycling, work-zone cracking dominates in electrolyte-supported SOCs with cracks initiated at the triple-phase boundaries, while only minor mechanical degradation occurs in hydrogen-electrode-supported SOCs after hundreds of thermal cycles. Under redox cycling, through-cracking of yttria-stabilized zirconia (YSZ) in the hydrogen electrode and electrolyte layers dominates. Finally, the simulation results suggest several crack-mitigation strategies, including decreasing the porosity in the hydrogen electrode support layer and synchronizing thermal strain to balance oxidation strain.

08 HYDROGEN↗
DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗
DOE OSTI2021

Constructing high-performance radiation-resistant ternary YSZ-MgO-CNT nanocomposites via tailored nanostructures

Developing long-lifetime bulk-form ceramic-based materials with high irradiation resistance is crucial for advanced nuclear systems. Here, we incorporated carbon nanotubes (CNTs) into yttria-stabilized zirconia (YSZ) and magnesia (MgO) nanocrystals to fabricate bulk YSZ-MgO-CNT nanocomposites with abundant ternary nanostructures by spark plasma sintering. To understand the role of tailored ternary nanostructure on irradiation, we investigated the microstructure and mechanical properties evolutions of the YSZ-MgO-CNT nanocomposites irradiated by multi-energy He + ions at high temperature to different fluences. Compared with the single-phase YSZ and ultrafine-grained YSZ-MgO composites, the YSZ-MgO-CNT nanocomposites possessed higher ability to manage irradiation-induced He bubbles/defects via the defect-interface interactions of proposed “loading-unloading” and “loading-transporting-unloading” mechanisms for controlling the dynamical behaviors of He atoms/defects in the CNT-doped ternary nanostructures, thereby presenting more stable microstructure and better performance in resisting irradiation hardening. In conclusion, this work provides insight into the design of advanced inert matrix nuclear fuel and new nuclear waste management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Particle Migration in Large Cross-Section Ceramic On-Demand Extrusion Components

Ceramic On-Demand Extrusion (CODE) is a direct ink writing process which allows for the creation of near theoretically dense ceramic components with large cross-sections due to oil-assisted drying. Here, Yttria-stabilized zirconia (YSZ) colloidal pastes were used in CODE to produce dense (multi-road infill and ≳ 98% relative density), large continuous volume (> 1 cm 3 ), and high fidelity (nozzle diameters ≲ 1 mm) structural ceramic components with nanoparticle feedstocks (~d 50 ≲ 1 µm). However, many of these printed components underwent significant particle migration after forming. The reason for this particle migration defect was investigated using the coffee-ring effect for dilute solutions and rheological methods for dense suspensions. Modifications to the colloidal paste, such as changes in solids loading, pH, or surfactant concentration were explored as to their effectiveness to mitigate the defect. Ultimately, paste formulation and printing trade-offs are discussed with respect to the post-printing defect and as to general direct-write patterning.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Diamond rotors

The resolution of magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectra remains bounded by the spinning frequency, which is limited by the material strength of MAS rotors. Since diamond is capable of withstanding 1.5–2.5x greater MAS frequencies, compared to state-of-the art zirconia, we fabricated rotors from single crystal diamond. When combined with bearings optimized for spinning with helium gas, diamond rotors could achieve the highest MAS frequencies to date. Furthermore, the excellent microwave transmission properties and thermal conductivity of diamond could improve sensitivity enhancements in dynamic nuclear polarization (DNP) experiments. The fabrication protocol we report involves novel laser micromachining and produced rotors that presently spin at ω r = 111.000 ± 0.004 kHz, with stable spinning up to 124 kHz, using N 2 gas as the driving fluid. Here, we present the first proton-detected 13 C/ 15 N MAS spectra recorded using diamond rotors, a critical step towards studying currently inaccessible ex-vivo protein samples with MAS NMR. Previously, the high aspect ratio of MAS rotors (~10:1) precluded fabrication of MAS rotors from diamond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Characterization of high thermal conductivity fuel surrogates before and after ion irradiation

High thermal conductivity nuclear fuels offer important potential advantages over traditional oxide-based fuels such as higher burnup, reduction in fission gas release, and better overall safety of the system. One proposed approach to high thermal conductivity fuels utilizes high thermal conductivity nonfissile additives with UO 2 fuel to lower the fuel operating temperature and thereby take advantage of the highly favorable radiation resistance of UO 2 at lower operating temperatures. However, differential swelling in the matrix and high conductivity additive phases during high dose irradiation could lead to internal cracking and poor performance. In the current study, ceria (CeO 2 ) and zirconia (ZrO 2 ) surrogate matrices were used to model UO2 behavior. Additives of 10 vol. % Al 2 O 3 or SiC in the form of short fibers or platelets were used for the high conductivity second phase. The nuclear fuel surrogates were sintered to achieve densities greater than 93% of the ideal values. Scanning electron microscopy (SEM) imaging and X-ray diffraction confirmed the uniform distribution of the second phase and that no intermetallic second phase was formed during sintering. The thermal conductivity of the sintered samples was measured from 50 °C to 900 °C and confirmed the desirable increase compared to pure CeO 2 /ZrO 2 pellets. Samples were irradiated with 20 MeV Ni 6+ ions at midrange doses ranging from 1 to 15 displacements per atom (dpa) and temperatures from 300 °C to 700 °C. Post irradiation characterization revealed a good stability of the samples at low to medium doses with matrix lattice parameter swelling of < 0.14 % but showed a significant microstructural deterioration and decrease of the mechanical properties at 15 dpa.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Burst and oxidation behavior of Cr-coated Zirlo during simulated LOCA testing

We report Cr-coated Zr-alloys are a near-term cladding concept to improve reactor safety during accident scenarios. Burst and steam oxidation behavior of bare and Cr-coated Zirlo claddings were examined under simulated loss-of-coolant accident conditions. The 4.4 µm coating had no substantial effect on ballooning or opening geometry but did increase burst temperatures at higher pressures. The coating reduced steam oxidation of the cladding compared to bare specimens, but in regions of high strain, the coating developed through-cracks allowing rapid underlying zirconia formation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Rare Earth Nickelate Electrodes Containing Heavily Doped Ceria for Reversible Solid Oxide Fuel Cells

The electrochemical performance of composite rare-earth nickelate-rare-earth doped ceria oxygen electrodes, with a high level of rare-earth doping in ceria are reported. Additionally, the chemical stability of these compositions is reported at both the sintering (1240 ?C) and operating temperature (800 ?C). Specifically, a lanthanum nickelate La2NiO4+d (LNO) ?? 50 mol% lanthanum doped ceria (LDC50) oxygen electrode and a neodymium nickelate Nd2NiO4+d (NNO) ?? 50 mol% neodymium doped ceria (NDC50) oxygen electrode are tested in solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes and compared to a composite (La0.75Sr0.25)0.95MnO3±d (LSM)-8 mol% yttria stabilized zirconia (YSZ) electrode. The LNO–LDC50 oxygen electrode reaches a current density which is approximately three times that of the LSM-YSZ electrode in SOFC mode at 0.7 V and approximately two times the LSM-YSZ electrode at 1.2 V in SOEC mode. Similarly the NNONDC50 oxygen electrode reaches a current density which is approximately two times and approximately one and a half times that of LSM-YSZ at 0.7 V and 1.2 V respectively. Oxygen surface exchange results for LNO and NNO are also reported which show different oxygen exchange kinetics during oxidation versus reduction steps.

solid oxide electrolysis, solid oxide fuel cell (S↗