Search NASA⌕ Search

SEARCH · Search NASA

Results for “bulk flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Structure-mechanical properties correlation in bulk LiPON glass produced by nitridation of metaphosphate melts

The glassy solid electrolyte Lithium phosphorous oxynitride (LiPON) has been widely researched in thin film solid state battery format due to its outstanding stability when cycled against lithium. In addition, recent reports show thin film LiPON having interesting mechanical behaviors, especially its ability to resist micro-scale cracking via densification and shear flow. Here, in the present study, we have produced bulk LiPON glasses with varying nitrogen contents by ammonolysis of LiPO 3 melts. The resulting compositions were determined to be LiPO 3-3z/2 N z , where 0 ≤ z ≤ 0.75, and the z value of 0.75 is among the highest ever reported for this series of LiPON glasses. The short-range order structures of the different resulting compositions were characterized by infrared, Raman, 31 P magic angle spinning nuclear magnetic resonance, and X-ray photoelectron spectroscopies. Instrumented nano-indentation was used to measure mechanical properties. It was observed that similar to previous studies, both trigonally coordinated (N t ) and doubly bonded (N d ) N co-exist in the glasses in about the same amounts for z ≤ 0.36, the limit of N content in most previous studies. For glasses with z > 0.36, it was found that the fraction of the N t increased significantly while the fraction of N d correspondingly decreased. The incorporation of nitrogen increased both the elastic modulus and hardness of the glass by approximately a factor of 1.5 when N/P ratio reaches 0.75. At the same time, an apparent embrittlement of the glass was observed due to nitridation, which was revealed by nanoindentation with an extra sharp nanoindenter tip.

25 ENERGY STORAGE↗
DOE OSTI2022

Mixing Pathways in Simple Box Models

Abstract Tracer variance budgets can be used to estimate bulk mixing in a control volume. For example, simple, analytical, bulk formulations of salt mixing, defined here as the destruction of salinity variance, can be found for estuaries with a riverine source of freshwater and a two-layer exchange flow at the mouth using salinity as a representative tracer. For a steady case, the bulk salt mixing M can be calculated as , where S in and S out are the representative salinities in the estuarine exchange flow, and Q R and Q in are the river and landward volume fluxes, respectively. The bulk salt mixing M can be considered as the sum of mixing pathways, where each pathway has a mixing of Q (Δ S ) 2 , where Q is the volume transport and Δ S is the salinity difference across the pathway. For the estuary case, one mixing path is associated with the river inflow, and the other is associated with the inflow of salty, oceanic water. This concept of linking mixing to input–output pathways is extended, in simple box models, from estuaries to scenarios with multiple inputs/outputs, as might be found in a complex estuarine/fjord network, in a region on a continental shelf, or any other control volume with multiple exchanges. This approach allows for the estimation of the relative contributions of each input–output pathway to the total mixing within a control volume.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Thermal property characterization of phase change materials in building applications: A systematic review of fundamentals, recent progress, and future directions

Phase change materials (PCMs) can reduce building peak loads and enable demand-responsive thermal energy storage (TES), but their deployment depends on reliable measurement and interpretation of thermal properties across laboratory, intermediate, and application scales. Here, this review systematically examines characterization methods, testing protocols, and recent advances for neat PCMs and PCM composites, emphasizing thermal conductivity, enthalpy-related properties (phase change temperature, latent heat, specific heat), and cycling stability. For thermal conductivity, we compare steady-state and transient techniques and note limitations when phase transition and contact resistance affect measurements. For enthalpy–temperature characterization, we discuss differential scanning calorimetry together with intermediate- and bulk-scale methods, including T-history, heat flow meter testing, and three-layer calorimetry (3LC), to generate application-relevant enthalpy–temperature profiles. Cycling stability is organized into four experimental families: thermoelectric–air, fully thermoelectric, water-bath, and in situ chamber approaches, with attention to separating reversible supercooling from true degradation such as phase segregation. We highlight emerging noncontact diagnostics, including infrared thermography and embedded sensing, for spatially resolved validation and multiscale interpretation. Finally, we review the growing use of AI and machine learning for property prediction, inverse characterization from experimental signals, and real-time state estimation in building-integrated TES. Key needs include harmonized protocols, interlaboratory benchmarking, uncertainty reporting, and metadata-rich datasets to accelerate reproducible PCM qualification for grid-flexible buildings.

AI↗
DOE OSTI2020

Relativistic Dynamics of Fluctuations and QCD Critical Point

Herein, we review the recent development on a systematic deterministic formalism describing dynamics of both bulk and fluctuations in an arbitrary relativistic hydrodynamic flow carrying conserved charges. In particular, we discuss the implementation of such general formalism near the QCD critical point.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Double-sided electron energy analyzer for measurement of non-Maxwellian electron energy distributions

Here, a double-sided electron energy analyzer is developed for studies of magnetic reconnection. It can measure electron energy distribution functions along two directions opposite to each other at the same time. Each side is composed of a floating reference grid, an energy selector grid, and a collector plate. The voltage of the selector grid is swept from –40 to 0 V with respect to the reference grid with a frequency of 1 MHz. This fast sweeping is required to resolve sub-Alfvénic changes in plasma quantities of the Magnetic Reconnection Experiment, where the typical Alfvénic time is a few microseconds. The reliability of the energy analyzer is checked in Maxwellian plasmas away from the reconnection region. In this case, the electron temperature computed from the electron energy distribution function agrees with measurements of a reference triple Langmuir probe. When it is located near the reconnection region, the temperatures of the tail electron population from both sides, facing into the electron flow and facing away from it, exceed the bulk electron temperature measured by the Langmuir probe by a factor of about 2.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Mixed-flow design for microfluidic printing of two-component polymer semiconductor systems

The rational creation of two-component conjugated polymer systems with high levels of phase purity in each component is challenging but crucial for realizing printed soft-matter electronics. Here, we report a mixed-flow microfluidic printing (MFMP) approach for two-component π -polymer systems that significantly elevates phase purity in bulk-heterojunction solar cells and thin-film transistors. MFMP integrates laminar and extensional flows using a specially microstructured shear blade, designed with fluid flow simulation tools to tune the flow patterns and induce shear, stretch, and pushout effects. This optimizes polymer conformation and semiconducting blend order as assessed by atomic force microscopy (AFM), transmission electron microscopy (TEM), grazing incidence wide-angle X-ray scattering (GIWAXS), resonant soft X-ray scattering (R-SoXS), photovoltaic response, and field effect mobility. For printed all-polymer (poly[(5,6-difluoro-2-octyl-2H-benzotriazole-4,7-diyl)-2,5-thiophenediyl[4,8-bis[5-(2-hexyldecyl)-2-thienyl]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl]-2,5-thiophenediyl]) [J51]:(poly{[N,N′-bis(2-octyldodecyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5′-(2,2′-bithiophene)}) [N2200]) solar cells, this approach enhances short-circuit currents and fill factors, with power conversion efficiency increasing from 5.20% for conventional blade coating to 7.80% for MFMP. Moreover, the performance of mixed polymer ambipolar [poly(3-hexylthiophene-2,5-diyl) (P3HT):N2200] and semiconducting:insulating polymer unipolar (N2200:polystyrene) transistors is similarly enhanced, underscoring versatility for two-component π -polymer systems. Mixed-flow designs offer modalities for achieving high-performance organic optoelectronics via innovative printing methodologies.

42 ENGINEERING↗
DOE OSTI2020

Complementary Metagenomic Approaches Improve Reconstruction of Microbial Diversity in a Forest Soil

ABSTRACT Soil ecosystems harbor diverse microorganisms and yet remain only partially characterized as neither single-cell sequencing nor whole-community sequencing offers a complete picture of these complex communities. Thus, the genetic and metabolic potential of this “uncultivated majority” remains underexplored. To address these challenges, we applied a pooled-cell-sorting-based mini-metagenomics approach and compared the results to bulk metagenomics. Informatic binning of these data produced 200 mini-metagenome assembled genomes (sorted-MAGs) and 29 bulk metagenome assembled genomes (MAGs). The sorted and bulk MAGs increased the known phylogenetic diversity of soil taxa by 7.2% with respect to the Joint Genome Institute IMG/M database and showed clade-specific sequence recruitment patterns across diverse terrestrial soil metagenomes. Additionally, sorted-MAGs expanded the rare biosphere not captured through MAGs from bulk sequences, exemplified through phylogenetic and functional analyses of members of the phylum Bacteroidetes . Analysis of 67 Bacteroidetes sorted-MAGs showed conserved patterns of carbon metabolism across four clades. These results indicate that mini-metagenomics enables genome-resolved investigation of predicted metabolism and demonstrates the utility of combining metagenomics methods to tap into the diversity of heterogeneous microbial assemblages. IMPORTANCE Microbial ecologists have historically used cultivation-based approaches as well as amplicon sequencing and shotgun metagenomics to characterize microbial diversity in soil. However, challenges persist in the study of microbial diversity, including the recalcitrance of the majority of microorganisms to laboratory cultivation and limited sequence assembly from highly complex samples. The uncultivated majority thus remains a reservoir of untapped genetic diversity. To address some of the challenges associated with bulk metagenomics as well as low throughput of single-cell genomics, we applied flow cytometry-enabled mini-metagenomics to capture expanded microbial diversity from forest soil and compare it to soil bulk metagenomics. Our resulting data from this pooled-cell sorting approach combined with bulk metagenomics revealed increased phylogenetic diversity through novel soil taxa and rare biosphere members. In-depth analysis of genomes within the highly represented Bacteroidetes phylum provided insights into conserved and clade-specific patterns of carbon metabolism.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Seedless nonresonant gas-flow velocimetry with single-shot coherent Rayleigh-Brillouin scattering

We demonstrate neutral gas-flow velocimetry by exploiting the optical dipole forces exerted by precisely tailored high-intensity laser fields on polarizable particles, in the form of single-shot coherent Rayleigh-Brillouin scattering (CRBS). This enables mapping of the velocity distribution function of the particles in a single laser shot of approximately 200 ns duration, allowing us to perform spectroscopic measurements in the time, rather than the frequency, domain. Importantly, CRBS results in a coherent signal beam, which renders the technique ideal for measurements in optically noisy environments. By correlating the time shift of the resulting spectrum to the Doppler shift caused by the bulk motion of particles, we perform neutral gas-flow velocimetry without the need to seed the flow, nondestructively, for a variety of gases, atomic or molecular. We demonstrate gas-flow velocimetry at flow velocities as low as 1 m ⁢s −1 , with similar velocity resolution, while temperature and gas density can also be estimated from the same single-shot spectra. To prove the effectiveness of the measurement technique, we benchmark it against Pitot tube measurements, which show excellent agreement.

Gerakis, Alexandros [Luxembourg Institute of Scien↗
DOE OSTI2022

Geophysical Characterization and Monitoring of the 200 Area Treated Effluent Disposal Facility to Support Permit Renewal; TEDF Geophysical Monitoring

The Treated Effluent Disposal Facility (TEDF), located in the 200 East Area of the Hanford Site, is a site where non-hazardous and non-radioactive liquid wastes are disposed into two state-permitted infiltration basins. In 2016, the Washington State Department of Ecology denied a permit renewal request for TEDF due to the inability to adequately assess the impact of TEDF discharge water on the underlying groundwater quality. TEDF overlies the relatively impermeable Ringold Lower Mud (RLM) unit, whose upper contact lies in the vadose zone approximately 30 m below ground surface and approximately 10 m above the water table boundary. The RLM is assumed to isolate TEDF discharge water from the natural groundwater aquifer, which is monitored using wellbores screened below the RLM. Therefore, samples collected from monitoring wells near TEDF are not considered representative of TEDF discharge water. Rather, TEDF discharge water is assumed to mound on top of the RLM to form a perched aquifer. To support permitting of the TEDF, a new monitoring well is required that can be used to sample water from the presumed perched water aquifer above the RLM. Ideally, the screened section of the well would be located at the peak of the perched water mound(s), which presumably occurs at the point of maximum vertical flux from TEDF to the RLM, or equivalently where the dominant infiltration flow paths reach the RLM. This report describes how time-lapse 3D electrical resistivity tomography (ERT) was used in conjunction with nominal TEDF discharge operations to image the dominant flow paths from each pond to the RLM. Results are summarized in Figure ES.1. Figure ES.1A shows a satellite image of the TEDF overlain by an array of surface ERT electrodes. The solid and dashed black circles denote the zones of maximum vertical flux at the RLM within the south and north ponds, respectively, and presumably the regions where perched water peaks during discharge. Figure ES.1B shows time-lapse difference imaging results approximately 15 days after switching discharge from the south pond to the north pond. Blue iso-surfaces beneath the north pond denote regions of increasing bulk electrical conductivity caused by increasing saturation due to infiltrating water. Red iso-surfaces beneath the south pond denote regions that were previously saturated during the south pond discharge and are now de-saturating, causing a decrease in bulk electrical conductivity. In both cases, the zones of maximum change mark the dominant flow paths to the RLM. Figure ES.1C shows time-lapse imaging results approximately 15 days after switching discharge from the north pond to the south pond. In this case, blue iso-surfaces mark the dominant flow paths to the RLM from the south pond. The red iso-surfaces mark the dominant flow paths that existed during discharge to the north pond. The regions of maximum change in bulk conductivity (due to saturation or desaturation) that mark the primary flow paths are equivalent in both cases and denoted by the dashed solid and black circles. If a perched water zone forms on the RLM, it is likely to mound within or near the dashed circle during discharge to the north pond, and in the solid circle during discharge to the south pond. In other words, if perched water mounding occurs, the circles mark the optimum locations suggested by the ERT imaging for monitoring boreholes to be placed, enabling samples to be collected that are representative of TEDF discharge impacts on groundwater quality.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Suppression of electroconvective and morphological instabilities by an imposed cross flow of the electrolyte

Electroconvective (EC) instability and its influence on surface morphological perturbations (Morph) are important in many applications, including electrodialysis, batteries, and fuel cells. In this work, we study the effects of a two-dimensional channel flow on the EC and Morph instabilities using two approaches. In the bulk analysis, we derive the asymptotic solutions for small and large wave numbers by neglecting the space charge layer and imposing a second kind electroosmosis slip velocity boundary condition on the electroneutral bulk region. In the full analysis, the instability of the entire region of the liquid electrolyte is analyzed using the ultraspherical spectral method. Both studies show that the flow significantly affects the EC instability. The imposed flow distorts the concentration field, causing a sheltering effect which hinders the ion transport from low- to high-concentration regions, and therefore suppresses the EC instability below a certain wave number. In combination with the viscous stabilization of the high wave number modes by the space charge layer, a sufficiently strong imposed flow can fully suppress the EC instability. The increment in the critical voltage for the instability onset is roughly proportional to the square root of the product of imposed velocity and double layer thickness. The imposed flow has a smaller effect on the Morph instability, except that it may remove the morphological modes resulting from the EC instability and thereby change the wave number of the most unstable mode.

42 ENGINEERING↗
DOE OSTI2022

Drag reduction and the Vogel exponent of a flexible beam in transient shear flows

Interactions between a flexible beam and a fluid in a channel are of great relevance to biological hairy surfaces, aquatic vegetation, marine life (e.g., fish gills), and many industrial systems alike. While steady state response of a beam to such flows is fairly well-explored, their behavior in the transient regime is not fully understood. Here, a series of numerical simulations are performed to study the laminar Couette flow of an incompressible viscous fluid past an elastic beam in a two-dimensional channel. The flexible beam is perpendicular to the direction of flow, and its base is fixed to the stationary bottom of the channel. We measure the evolution of the Vogel exponent, drag reduction, and reconfiguration number during the transient and steady-state response of the fluid–structure system for different geometrical and physical properties. Our benchmark shows a good agreement between numerical and experimental observations. Our results show that the system's steady-state response at different bulk-fluid velocities can be reproduced by investigating the shear flow response during the transient regime. We define a new variable that characterizes the evolution of the local velocity profile in the proximity of the free end of the beam and use that to characterize the transient-regime response. The analysis yields insight into the competing effects of elasticity of the beam and non-linear flow response.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Computational design of microarchitected porous electrodes for redox flow batteries

Porous electrodes are used as the core reactive component across electrochemical technologies. In flowing systems, controlling the fluid distribution, species transport, and reactive environment is critical to attaining high performance. However, conventional electrode materials like felts and papers provide few opportunities for precise engineering of the electrode and its microstructure. To address these limitations, architected electrodes composed of unit cells with spatially varying geometry determined via computational optimization are proposed. Resolved simulation is employed to develop a homogenized description of the constituent unit cells. These effective properties serve as inputs to a continuum model for the electrode when used in the negative half-cell of a vanadium redox flow battery. Porosity distributions minimizing power loss are then determined via computational design optimization to generate architected porosity electrodes. The architected electrodes are compared to bulk, uniform porosity electrodes and found to lead to increased power efficiency across operating flow rates and currents. The design methodology is further used to generate a scaled-up electrode with comparable power efficiency to the bench-scale systems. Finally, the variable porosity architecture and computational design methodology presented here thus offers a novel pathway for automatically generating spatially engineered electrode structures with improved power performance.

25 ENERGY STORAGE↗
DOE OSTI2020

Higher harmonic non-linear flow modes of charged hadrons in Pb-Pb collisions at $\sqrt{s_{\mathrm{NN}}}$ = 5.02 TeV

Anisotropic flow coefficients, v n , non-linear flow mode coefficients, χ n,mk , and correlations among different symmetry planes, ρ n,mk are measured in Pb-Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV. Results obtained with multi-particle correlations are reported for the transverse momentum interval 0.2 < p T < 5.0 GeV/c within the pseudorapidity interval 0.4 < |η| < 0.8 as a function of collision centrality. The v n coefficients and χ n,mk and ρ n,mk are presented up to the ninth and seventh harmonic order, respectively. Calculations suggest that the correlations measured in different symmetry planes and the non-linear flow mode coefficients are dependent on the shear and bulk viscosity to entropy ratios of the medium created in heavy-ion collisions. The comparison between these measurements and those at lower energies and calculations from hydrodynamic models places strong constraints on the initial conditions and transport properties of the system.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Ab-initio nucleon-nucleon correlations and their impact on high energy 16 O+ 16 O collisions

Investigating nucleon-nucleon correlations inherent to the strong nuclear force is one of the core goals in nuclear physics research. We showcase the unique opportunities offered by collisions of 16 O nuclei at high-energy facilities to reveal detailed many-body properties of the nuclear ground state. We interface existing knowledge about the geometry of 16 O coming from ab-initio calculations of nuclear structure with transport simulations of high-energy 16 O+ 16 O collisions. Bulk observables in these processes, such as the elliptic flow or the fluctuations of the mean transverse momentum, are found to depend significantly on the input nuclear model and to be sensitive to realistic clustering and short-range repulsive correlations, effectively opening a new avenue to probe these features experimentally. This finding demonstrates collisions of oxygen nuclei as a tool to elucidate initial conditions of small collision systems while fostering connections with effective field theories of nuclei rooted in quantum chromodynamics (QCD).

Zhang, Chunjian [Fudan University, Shanghai (China↗
DOE OSTI2024

Topological modes and spectral flows in inhomogeneous PT-symmetric continuous media

In classical Hermitian continuous media, the spectral-flow index of topological modes is linked to the bulk topology via index theorem. However, the interface between two bulks is usually non-Hermitian due to the inhomogeneities of system parameters. We show that the connection between topological modes and bulk topology still exists despite the non-Hermiticity at the interface if the system is endowed with PT symmetry. The theoretical framework developed is applied to the Hall magnetohydrodynamic model to identify a topological mode called topological Alfvén sound wave in magnetized plasmas. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Physical and Flow Properties of Glass Forming Chemicals (V2O5, SnO, SnO2, Cr2O3, FeCr2O4, and ZrSiO4) and Mixtures

For a sustainable nuclear waste vitrification process at the Hanford Tank Waste Treatment and Immobilization Plant (WTP), proper selection and consistent supply of glass-forming chemicals (GFCs) are crucial. Establishing rigorous acceptance criteria for the characterization of GFCs will be required to operate the vitrification facility and to mitigate any processing issues or failures. Low-activity wastes (LAW) are blended with GFCs to form slurry melter feeds and vitrified in a melter. To enhance properties of waste glasses, new chemicals are being introduced to the current GFC mixture (Vienna et al. 2016; Muller et al. 2017, 2019). In this study, three new GFCs were evaluated for enhanced LAW glass formulations: chromium oxide (Cr 2 O 3 ), vanadium oxide (V 2 O 5 ), and stannic oxide (SnO 2 ). These three oxide components are included in enhanced waste glass (EWG) formulations and GFCs with the appropriate physical and flow properties are needed. As a starting point, single metal oxide GFCs: Cr 2 O 3 , V 2 O 5 , and SnO 2 were sourced and tested. To characterize these new individual GFCs and mixtures of GFCs, the industrial bulk characterization consultant, Jenike and Johanson, was employed to measure physical and flow properties of individual GFCs and their mixtures. Pacific Northwest National Laboratory (PNNL) also measured several selected physical properties for data evaluation as a quality assurance step. In addition, PNNL measured physical and rheological properties of slurry melter feeds containing those GFCs. Subsequent data analyses and verification were conducted. The purpose of this report is to assess the applicability of these GFCs for LAW vitrification based on their properties. This report will help understand measured data and evaluate new GFCs for use. Moreover, this report may give useful insights to help troubleshoot any GFC and melter feed transport and mixing issues that arise during processing, leading to a successful cleanup mission at WTP.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Multi-fidelity kinetic theory-based approach for the prediction of particle attrition: Application to jet cup attrition system

The timescale difference between the “fast” flow dynamics of fluidized bed reactors and the relatively “slow” rate of particle degradation makes the direct computational prediction of attrition challenging. An approach to this challenge is a multi-fidelity strategy where a high fidelity model for the flow dynamics is coupled with a lower fidelity model for the long-time resolution of the bulk attrition of the reactor inventory. We implement this approach using high-fidelity kinetic theory simulations to calculate the flow dynamics which are post-processed to calculate the frequency and intensity of the particle-particle and particle-wall collisions (e.g. collision energy spectra). This is combined with the particle breakage properties to construct the coefficients for a low-fidelity model [e.g. Monazam et al., 2018, Powder Technology 340, p. 528-536]. Simulations are performed of a jet cup attrition system containing Canadian hematite (Monazam et al. 2018). Furthermore, these are first analyzed using the collision energy spectra. Quantitative predictions of the mass loss are made using a low-fidelity model derived from the collision-spectra and a calibrated material breakage coefficient. The results are found to compare favorably with the experimental measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Spring 2022 update on the status of the Local Wavenumber Model (LWN) in xRAGE

An updated implementation of the Local Wavenumber Model (LWN) is discussed, primarily differing from recent versions by placing a greater focus on capturing a wide variety of turbulent flows including compressible flows. New models are introduced for spectral backscatter effects, the effect of bulk compression on the spectra, and incorporating the multispecies variables tracked in BHR4. Methods for reducing the compurational expense of tracking spectra for turbulent quantites are also investigated. Like recent versions of BHR, we test LWN in a number of canonical flows using a single set of coefficients, but additional coefficient tuning is likely to be required to improve the agreement with some of these flows.

36 MATERIALS SCIENCE↗