Search NASA⌕ Search

SEARCH · Search NASA

Results for “device stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

A Wind-Tunnel Investigation of a Transonic-Transport Configuration Utilizing Drag-Reducing Devices at Mach Numbers from 0.20 to 1.03

The static longitudinal stability and control and lateral characteristics of a transonic-transport model, incorporating recent drag-reducing devices, has been investigated in the Langley 8-foot transonic pressure tunnel. The wing was cambered, had a thickened root and a taper ratio of 0.3. Wing sweepback angles of 45 degrees and 40 degrees were investigated with corresponding aspect ratios of 7 and 8, respectively. Modifications to the model for reducing the drag were: a forward fuselage addition and special bodies (four big enough to house jet engines) added to the upper surface of the wing. Other components and changes investigated included an empennage, a wing-tip body, wing fences, wing trailing-edge flaps, horizontal-tail settings, and wing dihedral angle. The investigation covered the Mach number range from 0.20 to 1.03 for the angle-of-attack range from -5 degrees to 15.4 degrees, and a sideslip angle of -5 degrees, in the Reynolds number range from 0.52 times 10(exp 6) to 1.94 times 10(exp 6) based on the wing mean aerodynamic chord. The various fuselage and wing additions delayed the drag-rise Mach number and greatly reduced the drag beyond the drag rise. The wing bodies markedly alleviated unstable pitch tendencies throughout the test Mach number range. At low landing speeds, the wing bodies exhibited little interference with the ability of trailing-edge flaps to increase the lift near maximum lift coefficient; and the use of fences greatly reduced the severe longitudinal instability trend at landing attitudes. The model with a 6 degree dihedral angle exhibited positive lateral and directional stability characteristics in the presence of the fuselage and wing additions. An increase in drag-rise Mach number associated with the fuselage and wing additions on the 40 degree sweptback wing combination was similar to that for the comparable 45 degree combination. These additions did, however, reduce the drag of the 40 degree sweptback configurations more than the 45 degree configurations in the transonic speed range.

Loving, Donald L.↗
NASA NTRS2015

Radiation-Resistant Photon-Counting Detector Package Providing Sub-ps Stability for Laser Time Transfer in Space

We are reporting on a design, construction and performance of photon-counting detector packages based on silicon avalanche photodiodes. These photon-counting devices have been optimized for extremely high stability of their detection delay. The detectors have been designed for future applications in fundamental metrology and optical time transfer in space. The detectors have been qualified for operation in space missions. The exceptional radiation tolerance of the detection chip itself and of all critical components of a detector package has been verified in a series of experiments.

radiation hardness↗
NASA NTRS2004

Space Application Requirements for Organic Avionics

The NASA Marshall Space Flight Center is currently evaluating polymer based components for application in launch vehicle and propulsion system avionics systems. Organic polymers offer great advantages over inorganic corollaries. Unlike inorganics with crystalline structures defining their sensing characteristics, organic polymers can be engineered to provide varying degrees of sensitivity for various parameters including electro-optic response, second harmonic generation, and piezoelectric response. While great advantages in performance can be achieved with organic polymers, survivability in the operational environment is a key aspect for their practical application. The space environment in particular offers challenges that must be considered in the application of polymer based devices. These challenges include: long term thermal stability for long duration missions, extreme thermal cycling, space radiation tolerance, vacuum operation, low power operation, high operational reliability. Requirements for application of polymer based devices in space avionics systems will be presented and discussed in light of current polymer materials.

Watson, Michael D.↗
NASA NTRS1992

Adaptive attitude control and momentum management for large-angle spacecraft maneuvers

The fully coupled equations of motion are systematically linearized around an equilibrium point of a gravity gradient stabilized spacecraft, controlled by momentum exchange devices. These equations are then used for attitude control system design of an early Space Station Freedom flight configuration, demonstrating the errors caused by the improper approximation of the spacecraft dynamics. A full state feedback controller, incorporating gain-scheduled adaptation of the attitude gains, is developed for use during spacecraft on-orbit assembly or operations characterized by significant mass properties variations. The feasibility of the gain adaptation is demonstrated via a Space Station Freedom assembly sequence case study. The attitude controller stability robustness and transient performance during gain adaptation appear satisfactory.

Parlos, Alexander G.↗
NASA NTRS1991

Effectiveness of large booms as nutation dampers for spin stabilized spacecraft

The issue of using long slender booms as pendulous nutation damping devices on spinning aircraft is discussed. Motivation comes from experience with the Galileo Spacecraft, whose magnetometer boom also serves as a passive nutation damper for the spacecraft. Performance analysis of a spacecraft system equipped with such systems are relatively insensitive to changes in the damping constant of the device. However, the size and arrangement of such a damper raises important questions concerning spacecraft stability in general.

Eke, F. O.↗
NASA NTRS2014

Materials International Space Station Experiment (MISSE): Overview, Accomplishments and Future Needs

Materials and devices used on the exterior of spacecraft in low Earth orbit (LEO) are subjected to environmental threats that can cause degradation in material properties, possibly threatening spacecraft mission success. These threats include: atomic oxygen (AO), ultraviolet and x-ray radiation, charged particle radiation, temperature extremes and thermal cycling, micrometeoroid and debris impacts, and contamination. Space environmental threats vary greatly based on spacecraft materials, thicknesses and stress levels, and the mission environment and duration. For more than a decade the Materials International Space Station Experiment (MISSE) has enabled the study of the long duration environmental durability of spacecraft materials in the LEO environment. The overall objective of MISSE is to test the stability and durability of materials and devices in the space environment in order to gain valuable knowledge on the performance of materials in space, as well as to enable lifetime predictions of new materials that may be used in future space flight. MISSE is a series of materials flight experiments, which are attached to the exterior of the International Space Station (ISS). Individual experiments were loaded onto suitcase-like trays, called Passive Experiment Containers (PECs). The PECs were transported to the ISS in the Space Shuttle cargo bay and attached to, and removed from, the ISS during extravehicular activities (EVAs). The PECs were retrieved after one or more years of space exposure and returned to Earth enabling post-flight experiment evaluation. MISSE is a multi-organization project with participants from the National Aeronautics and Space Administration (NASA), the Department of Defense (DoD), industry and academia. MISSE has provided a platform for environmental durability studies for thousands of samples and numerous devices, and it has produced many tangible impacts. Ten PECs (and one smaller tray) have been flown, representing MISSE 1 through MISSE 8, yielding long-duration space environmental performance and durability data that enable material validation, processing recertification and space qualification; improved predictions of materials and component lifetimes in space; model verification and development; and correlation factors between space-exposure and ground-facilities enabling more accurate in-space performance predictions based on ground-laboratory testing. A few of the many experiment results and observations, and their impacts, are provided. Those highlighted include examples on improved understanding of atomic oxygen scattering mechanisms, LEO coating durability results, and polymer erosion yields and their impacts on spacecraft design. The MISSE 2 Atomic Oxygen Scattering Chamber Experiment discovered that the peak flux of scattered AO was determined to be 45 deg from normal incidence, not the model predicted cosine dependence. In addition, the erosion yield (E(sub y)) of Kapton H for AO scattered off oxidized-Al is 22% of the E(sub y) of direct AO impingement. These results were used to help determine the degradation mechanism of a cesium iodide detector within the Hubble Space Telescope Cosmic Origins Spectrograph Experiment. The MISSE 6 Indium Tin Oxide (ITO) Degradation Experiment measured surface electrical resistance of ram and wake ITO coated samples. The data confirmed that ITO is a stable AO protective coating, and the results validated the durability of ITO conductive coatings for solar arrays for the Atmosphere-Space Transition 2 Explorer program. The MISSE 2, 6 and 7 Polymer Experiments have provided LEO AO Ey data on over 120 polymer and composites samples. The flight E(sub y) values were found to range from 3.05 x 10(exp -26) cu cm/atom for the AO resistant polymer CORIN to 9.14 x 10(exp -26) cu cm/atom for polyoxymethylene (POM). In addition, flying the same polymers on different missions has advanced the understanding of the AO E(sub y) dependency on solar exposure for polymers containing fluorine. The MISSE polymer results are highly requested and have impacted spacecraft design for WorldView-2 & -3, the Global Precipitation Measurement-Microwave Imager, and other spacecraft. The flight data has enabled the development of an Atomic Oxygen Erosion Predictive Tool that allows the erosion prediction of new and non-flown polymers. The data has also been used to develop a new NASA Technical Standards Handbook "Spacecraft Polymers Atomic Oxygen Durability Handbook." Many intangible benefits have also been derived from MISSE. For example, over 40 students have collaborated on Glenn's MISSE experiments, which have resulted in greater than $80K in student scholarships and awards in national and international science fairs. Students have also given presentations and won poster competition awards at international space conferences.

Flight Experiment↗
NASA NTRS1973

Review of drag measurements from flight tests of manned aircraft with comparisons to wind-tunnel predictions

In-flight studies of the overall and local components of drag of many types of aircraft were conducted. The primary goal of these studies was to evaluate wind-tunnel and semiempirical prediction methods. Some evaluations are presented in this paper which may be summarized by the following observations: Wind-tunnel predictions of overall vehicle drag can be accurately extrapolated to flight Reynolds numbers, provided that the base drag is removed and the boattail areas on the vehicle are small. The addition of ablated roughness to lifting body configurations causes larger losses in performance and stability than would be expected from the added friction drag due to the roughness. Successful measurements of skin friction have been made in flight to Mach numbers above 4. A reliable inflatable deceleration device was demonstrated in flight which effectively stabilizes and decelerates a lifting aircraft at supersonic speeds.

Pyle, J. S.↗
NASA NTRSDate not supplied

Development and Testing of Pulse Guns for Combustion Instability Testing

Combustion stability requirements of a liquid propellant rocket engine are most commonly verified by evaluating the oscillatory pressure or vibration characteristics following an artificial disturbance of the combustion in the combustion chamber. Two types of devices are most commonly used for dynamic stability rating – nondirectional bombs and pulse guns. Bombs have historically been used most often, especially for the large engines developed around the Apollo era. However, bombs in recent years have become much more expensive and difficult to procure, and their transportation and handling requirements have become more demanding. Pulse guns, with inherently less expensive materials, and far less restrictive handling and shipping requirements, have become an attractive alternative. The NASA Marshall Space Flight Center has developed a pulse gun for use during future development programs at the center, and as a design reference for interested commercial users. The objective of this paper is to present the different variants of the pulse gun and characterize performance over a range of parameters. The parameters include the breech diameter and corresponding volume, barrel length, amount of gun powder used, the method of containing the gunpowder within the breech, and the pressure rating of the burst disk. In total, 44 tests were conducted with the pulse gun firing into a test chamber pressurized to 2300 psig with gaseous nitrogen. The best experimental results – including the highest and most consistent peak pressure amplitudes recorded by dynamic pressure sensors in the test chamber – were from a configuration consisting of a 0.40” inner-diameter breech, 15-16 grains of gunpowder wrapped in cigarette paper, and a 24,000 psid burst disk. With this configuration, the zero-to-peak overpressures recorded in the test chamber ranged from about 37% to 58% of the 2300 psig mean pressure, which is adequate for typical combustion stability rating. To complement the data analysis, the acoustics of the pressure waves as they propagated through the pulse gun and into the test chamber were modeled. A more comprehensive final report of this pulse gun development program is planned to be available in the near future.

Pulse Gun↗
NASA NTRS1981

Simple JFET oscillator

Device used in mixers, modulators, and function generators provides stable sine-wave signal compatible with both integrated circuits and discrete-component assemblies. Oscillator's frequency is tunable over narrow band about design value. Frequency range, stability, linearity, and low power drain of device are suited to communications receivers and transmitters and digital microprocessors, computers, and displays. Circuit simplicity allows for easy monolithic construction.

Kleinberg, L. L.↗
NASA NTRS1971

The silicon vidicon: Integration, storage and slow scan capability - Experimental observation of a secondary mode of operation.

Description of the performance of the silicon diode array vidicon - an imaging sensor which possesses wide spectral response, high quantum efficiency, and linear response. These characteristics, in addition to its inherent ruggedness, simplicity, and long-term stability and operating life make this device potentially of great usefulness for ground-base and spaceborne planetary and stellar imaging applications. However, integration and charged storage for periods greater than approximately five seconds are not possible at room temperature because of diode saturation from dark current buildup. Since dark current can be reduced by cooling, measurements were made in the range from -65 to 25 C. Results are presented on the extension of integration, storage, and slow scan capabilities achievable by cooling. Integration times in excess of 20 minutes were achieved at the lowest temperatures. The measured results are compared with results obtained with other types of sensors and the advantages of the silicon diode array vidicon for imaging applications are discussed.

Ando, K. J.↗
NASA NTRS1979

Magnetic suspension system for a laboratory model annular momentum control device

Feasibility of the annular momentum control device (AMCD) for the control and stabilization of spacecraft is presented. The AMCD is momentum storage equipment consisting of a thin rim, magnetically suspended and rotated by noncontacting electromagnetic actuators. The laboratory model AMCD, the rim, and the magnetic suspension system are described, along with their evaluation tests. Because it utilizes permanent magnet flux biased magnetic bearing elements, the original laboratory model magnetic suspension system produced control limitations, and a new suspension system which used zero flux bias was designed and fabricated. Tests of the improved system show that a medium control loop bandwidth is required to achieve stability at low rim velocities, but at higher rim speed the bandwidth of the control loop interacts with bending modes of the rim and causes instability. Decreasing the bandwidth by changing to a precession control mode is discussed, and the results of such a computer simulation are presented.

Groom, N. J.↗
NASA NTRS1982

Low noise buffer amplifiers and buffered phase comparators for precise time and frequency measurement and distribution

Extremely low noise, high performance, wideband buffer amplifiers and buffered phase comparators were developed. These buffer amplifiers are designed to distribute reference frequencies from 30 KHz to 45 MHz from a hydrogen maser without degrading the hydrogen maser's performance. The buffered phase comparators are designed to intercompare the phase of state of the art hydrogen masers without adding any significant measurement system noise. These devices have a 27 femtosecond phase stability floor and are stable to better than one picosecond for long periods of time. Their temperature coefficient is less than one picosecond per degree C, and they have shown virtually no voltage coefficients.

Eichinger, R. A.↗
NASA NTRS1986

Batch Gas-Sampling System

Sampler collects air or other gases in consistent way and stabilizes them for later chemical analysis. Device used for concentrations ranging from few parts per million to 100 percent. Also separates and collects particles in gas for analysis. Gas flows into vacuum sphere when solenoid valve opened. As it passes through conversion tube, constituent of gas forms stable compound that remains in conversion tube for analysis at later time. Sampler parts made of glass, polytetrafluoroethylene, and stainless steel so they do not react with sample.

Diaz, Vernon, Jr.↗
NASA NTRS1987

Three-Axis Attitude Control With a Single Wheel

Single-device attitude-control system provides stabilization along three axes. Flywheel connected to electronically controlled motor rotates on magnetic bearing. At high rotational speed, small angular displacements about x and y axes, in response to control signals enable storage of relatively large amounts of angular momentum. Angular momentum about z axis stored in changes in rotational speed.

Studer, P. A.↗
NASA NTRS1990

A 200 MHz surface acoustic wave mass microbalance

The principle of operation of the surface acoustic wave (SAW) piezoelectric crystals used as microgravimetric sensors in mass microbalances is discussed. Special attention is given to a SAW 200-MHz crystal developed for measuring molecular deposition on spacecrafts, whose operating frequency does not depend on the thickness of the crystal. The frequency stability of the 200 MHz SAW device is better than 5 x 10 exp -9, which corresponds to a lower limit-of-detection of 3 x 10 exp -12 g for a signal-to-noise ratio of 3. A block diagram of the 200 MHz SAW mass microbalance and a schematic diagram of SAW resonator are presented together with performance data of this device.

Bowers, William D.↗
NASA NTRS1953

Method for calculating the rolling and yawing moments due to rolling for unswept wings with or without flaps or ailerons by use of nonlinear section lift data

The methods of NACA Reports 865 and 1090 have been applied to the calculation of the rolling- and yawing-moment coefficients due to rolling for unswept wings with or without flaps or ailerons. The methods allow the use of nonlinear section lift data together with lifting-line theory. Two calculated examples are presented in simplified computing forms in order to illustrate the procedures involved.

CONTROLS - COMPLETE WINGS↗