Search NASA⌕ Search

SEARCH · Search NASA

Results for “digital Image correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of Backing Plate and Thermal Boundary Conditions for High-Speed Friction Stir Welding of 25-mm Thick Aluminum Alloy 7175-T79

Here this study demonstrates high-speed (150 mm/min) single pass friction stir butt joining of 25 mm thick aluminum alloy 7175-T79. To understand the impact of quenching and cooling rate on process responses, joint strength, and grain size distributions across the weld thickness, we performed a series of friction stir welding (FSW) trials in air and with a trailing water spray using steel and composite backing plates (BP). Welds made in air and trailing water spray exhibit significantly different hardness distributions across the nugget, heat affected zone (HAZ), and HAZ minimum hardness as evidenced by detailed microhardness mapping. The effect of trailing water spray (TWS) on joint efficiency overshadows the influence of BP composition due to the vastly different contribution to quenching. TWS also resulted in a multifaceted effect on FSW such as lowering processing temperature, increasing X and Z forces while lowering Y force, and narrow heat affecting zone. Finally, digital image correlation (DIC)-based fracture mode analysis and grain size measurements correlate with the hardness distribution.

42 ENGINEERING↗
DOE OSTI2020

Experimental Modal Analysis Using Phase Quantities from Phase-Based Motion Processing and Motion Magnification

Phase-based motion processing and the associated Motion Magnification that it enables has become popular not only for the striking videos that it can produce of traditionally stiff structures visualized with very large deflections, but also for its ability to pull information out of the noise floor of images so that they can be processed with more traditional optical techniques such as digital image correlation or feature tracking. While the majority of papers in the literature have utilized the Phase-based Image Processing approach as a pre-processor for more quantitative analyses, the technique itself can be used directly to extract modal parameters from an image, noting that the extracted phases are proportional to displacements in the image. Therefore, once phases are extracted, they can be fit using traditional experimental modal analysis techniques. This produces a mode “shape” where the degrees of freedom are phases instead of physical motions. These phases can be scaled to produce on-image visualizations of the mode shapes, rather than operational shapes produced by bandpass filtering. Modal filtering techniques can also be used to visualize motions from an environment on an image using the modal phases as a basis for the expansion.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

A Method for Dynamic Kolsky Bar Compression at High Temperatures: Application to Ti-6Al-4V

Abstract An experimental apparatus for measuring the dynamic behavior of materials subjected to strain rates on the order of 10 $$^3$$ 3 s $$^{-1}$$ - 1 and temperatures up to 800°C with a unique triple actuation system is developed in this work. This system is based on the traditional Kolsky (or split-Hopkinson pressure) bar design, with the addition of an external furnace used to heat the specimen to the desired temperature. A synchronized triple pneumatic actuation system is used to control the motion and timing of the the sample, incident, and transmitted bars. The cold contact time (CCT), or the time during which the heated sample is in contact with the room temperature bars before compression, is measured experimentally and carefully controlled to minimize the development of a temperature gradient across the sample and avoid heating of the bars. Experiments are performed in conjunction with ultra high speed imaging and 2D digital image correlation (DIC), as well as high speed thermal imaging. To verify the viability of the proposed system, experiments were conducted on Ti-6Al-4V (wt.%) at temperatures from 25°C up to and 800°C at an average strain rate of approximately 1200 s $$^{-1}$$ - 1 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Origin, parameters, and underlying deformation mechanisms of propagating deformation bands in irradiated 316L stainless steel

Lüders-type propagating deformation bands were observed in specimens of irradiated 316L stainless steel samples removed from Spallation Neutron Source target vessels after service. Mechanical testing with digital image correlation (DIC) and in-situ tensile testing with scanning electron microscopy electron backscatter diffraction showed that the observed Lüders-type behavior was not related to the known transformation-induced plasticity or twinning-induced plasticity behavior. Instead, the phenomenon occurs at small local strain values before a significant amount of martensite or deformation twins appear in the microstructure. Microstructural analysis and in-situ mechanical test results suggest Lüders-type band formation and propagation were related to the appearance and evolution of defect-free channels—analogous to slip bands. A modified Swift equation with a Ludwigson-like component was offered to rationalize the phenomenon and model the strain-softening processes at small strain values. Finally, the results indicate complex microstructural processes and deformation mechanisms were active at small strain values and underline the benefits of advanced mechanical test approaches such as DIC.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Slip localization behavior at triple junctions in nickel-base superalloys

Incipient slip localization in the vicinity of hundreds of grain boundary triple junctions (TJs) in a lightly deformed nickel-base superalloy IN718 is studied using a combination of three-dimensional (3D) crystal plasticity finite element (CPFE) modeling, high resolution digital image correlation (HR-DIC) and 3D electron back-scatter diffraction tomography (3D EBSD). A 3D reconstruction method enables identification of thousands of TJs and correspondence of any observed slip bands with their originating TJ lines below the specimen surface. Here, we present a large-scale CPFE model of the experimental 3D microstructure composed of high-fidelity representation of the TJ lines and the boundaries and interiors of the parent grains and use it to calculate the local micromechanical response and slip activity of all TJs at the onset of macroscopic yielding. Statistical analysis of the calculated quantities reveal TJs develop larger stress concentration and grain-average re-orientation than grain interiors and grain boundaries, however no substantial differences in cumulative slip were found among these microstructural regions. We find that TJs with observed slip bands generate lower grain-average re-orientation, fewer active slip systems, and more localized slip on a single system than those without. The distinctions in the reorientation and slip activity are stronger in TJs that experience more intense slip.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct observation of strain-enhanced hydrogen segregation and failure at high-angle grain boundaries in nickel

Understanding the mechanisms underlying hydrogen embrittlement remains difficult, even in single-element metals. Both microstructure and stress state influence hydrogen distribution in metals and alloys, which impacts deformation and failure. Here, in this work, we use in-situ Kelvin probe force microscopy (KPFM) to monitor the hydrogen distribution in pure nickel over time at 1.1 % and 3.5 % strain. The sample strained to 3.5 % results in preferential hydrogen segregation to high-angle grain boundaries whereas the sample strained to 1.1 % does not exhibit preferential hydrogen segregation. Optical digital image correlation (DIC) shows that hydrogen charging results in both localized and reduced strains during tensile testing of a notched sample. Later stages of deformation and failure (e.g. microcracking) are studied by using in-situ transmission X-ray microscopy (TXM). TXM reveals nanoscale structural changes to a propagating crack in a hydrogen environment. Localized void growth and secondary cracking occur at grain boundaries near the primary crack front. Correlative electron backscattering diffraction (EBSD) is used to relate the cracking at grain boundaries to the hydrogen segregation observed in KPFM. These findings are unified in a proposed hydrogen embrittlement mechanism that describes the interaction of hydrogen with grain boundaries, and the role of grain boundaries in hydrogen embrittlement.

Grain boundary fracture↗
DOE OSTI2025

Mechanical properties and strain localization of WA-DED printed P91 steel

This paper discusses a P91 steel block that was additively manufactured by wire arc direct energy deposition (WA-DED) followed by two types of post-process heat treatment (PPHT). Vickers microhardness and digital image correlation tensile tests were performed along the building direction. The global mechanical properties (i.e., microhardness and tensile properties) and the local mechanical responses (i.e., hardness fluctuation and strain localization) were systematically investigated. Results showed that (1) all P91 specimens showed higher strengths than American Society of Mechanical Engineers standard requirements for wrought P91 steel, (2) the as-printed P91 exhibited much higher average hardness and fluctuations than that after PPHT, (3) PPHT reduced P91 strengths but improved the ductility significantly, and (4) strain localization presented in the as-printed specimen during uniform deformation in tensile tests. The hardness fluctuation and strain localization along the building direction of the AP P91 were caused by different thermal histories received during WA-DED. The study indicated that PPHT, ideally tempering-only heat treatment, is necessary for the WA-DED printed P91 steel.

Mechanical properties↗
DOE OSTI2021

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the efficacy of post-build thermomechanical treatments to improve properties of Zirconium fabricated using ultrasonic additive manufacturing

Here, hot-isostatic pressing has been applied to Zirconium plate fabricated using the ultrasonic additive manufacturing (UAM) technique to enhance interfacial bond quality. Specimens heated to 800 C for 1 h at 100 MPa pressure showed grain growth across many prior foil-to-foil interfaces, thereby increasing foil adhesion. In addition to the material softening induced by a loss of Hall-Petch strengthening, premature failure of specimens loaded parallel to the build direction was observed. Premature specimen failure was attributed to the local delamination at prior foil-to-foil boundaries where grain growth was pinned by Ti impurities introduced during the UAM process via the interaction between a Ti-alloy buffer foil and the welded Zr-foils underneath. In addition, the presence of Ti along select foil interfaces resulted in the nucleation and growth of secondary (Zr,Ti)(Fe,Cr) laves phases during higher-temperature thermomechanical processing. Using a combination of micro-scale X-ray computed tomography, fractography, and in-situ digital image correlation, the effect of defects along prior foil-to-foil boundaries was revealed as delamination-assisted plasticity accelerated specimen failure in preferred tensile orientations. These findings underscore the importance of impurity control when optimizing weld quality of higher-strength material systems using ultrasonic welding.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High temperature creep model development using in-situ 3-D DIC techniques during a simulated LOCA transient

In-situ strain measurements of fuel cladding can enable high-throughput data collection and validation to support accelerated qualification of cladding materials. Here, in this work, 3D digital image correlation was used to map strain for both Zircaloy-4 (Zry-4) and Cr-coated Zry-4 during two types of cladding rupture experiments: isobaric temperature ramp tests at 5 °C/s and isothermal pressure jump tests at 600 °C. Zry-4 strain data initially showed a temperature dependence expected for creep deformation, yet a shift to a new plastic deformation mechanism not reported in literature dominated during the finals seconds prior to rupture. Cr-coated Zry-4 did not show the change in deformation mechanism at the end of life and showed a delay in measurable creep deformation. Stress dependences were similar for Zry-4 and Cr/Zry-4 during pressure jump tests. Cr-coatings were found to decrease the strain rate during both testing scenarios. Creep parameters were calculated to support modelling efforts regarding design basis accidents.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bulk-scale stress–strain hysteresis in layered crystalline solids: A study of graphite and Ti 3 SiC 2

Polycrystalline graphite and the MAX phase Ti 3 SiC 2 are layered crystalline solids with similar deformation mechanisms, including basal slip, ripplocation boundaries (RBs), kink boundaries (KBs), and cracking. The interplay of these mechanisms, notably in energy dissipation, has been much discussed in the past twenty-five years. This study builds upon previous work, investigating deformation with a renewed emphasis on the bulk-scale and given recent findings concerning RBs. Our investigation compares the evolution of energy dissipation, nonlinear recoverable and irrecoverable strain, and damage upon increasing stress for graphite and Ti 3 SiC 2 . Benitez et al.’s (2016) methodology of compressive cyclic loading and post-mortem electron backscatter diffraction (EBSD) to assess the prevalence of kinking based on low-angle grain boundaries (LAGBs) was used. Strains were measured with digital image correlation and EBSD was conducted on Ti 3 SiC 2 leveraging dictionary indexing, which was necessary herein to identify LAGBs accurately. The stress–strain stages of Ti 3 SiC 2 agree with literature on Ti 2 AlC. Damage and energy dissipation were more accelerated in graphite. No significant difference was observed in the fraction of LAGBs between pristine and unloaded Ti 3 SiC 2 . Trends observed and EBSD evidence that KBs were not dominant suggest that RBs are the primary dissipator of energy in both materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A comparative study of calibration techniques for finite strain elastoplasticity: Numerically-exact sensitivities for FEMU and VFM

Accurate identification of material parameters is crucial for predictive modeling in computational mechanics. Here, the two primary approaches in the experimental mechanics community for calibration from full-field digital image correlation data are known as finite element model updating (FEMU) and the virtual fields method (VFM). In VFM, the objective function is a squared mismatch between internal and external virtual work or power. In FEMU, the objective function quantifies the weighted mismatch between model predictions and corresponding experimentally measured quantities of interest. It is minimized by iteratively updating the parameters of an FE model. While FEMU is seen as more flexible, VFM is commonly used instead of FEMU due to its considerably greater computational expense. However, comparisons between the two methods usually involve approximations of gradients or sensitivities with finite difference schemes, thereby making direct assessments difficult. Hence, in this study, we compare VFM and FEMU in the context of numerically-exact sensitivities obtained through local sensitivity analyses and the application of automatic differentiation software. To this end, we conduct a series of test cases to assess both methods under practical challenges using a finite strain elastoplasticity model.

Automatic differentiation↗
DOE OSTI2020

Analysis of tow architecture variability in biaxially braided composite tubes

Spatial deviations in composite braid unit cell dimensions limit mechanical performance and are challenging to model. Full-field measurements of the irregular tow placement in biaxially braided composite tubes were obtained by digital image correlation. Analysis of the reconstructed tow paths showed long-range defects along the hoop direction with short-range defects dominating the biased tow direction. A route toward numerical simulation of the composite response is established by developing a 3D model of the composite using the measured tow trajectories. Finally, a comparison to previously-published triaxial braid results indicates axial tows work to constrain unit cells dimensions along the hoop direction.

3-Dimensional reinforcement↗
DOE OSTI2020

Quantifying the effect of tow architecture variability on the performance of biaxially braided composite tubes

Targeted experiments are performed with stereoscopic digital image correlation to quantify the effect of irregular braid structure on the local surface mechanical response of carbon-fiber reinforced epoxy composite tubes. Virtual models comparing both nonuniform and uniform tow structure of the outer braid of each specimen are integrated into numerical simulations similar to experiments. Experimental and numerical results agree well. Statistical tests are used to support correlations between as-manufactured braid variation ranges to local increases in stress up to 18% compared to an ideal, uniform structure in the elastic regime. Results support improved manufacturing and modeling efforts of defect sensitive braided composites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic fracture of glass fiber-reinforced ductile polymer matrix composites and loading rate effect

Here, the dynamic fracture of S-2 glass fiber-reinforced polymer matrix composites (FRPMCs) was investigated in this study. The matrix ductility was improved by a recently developed network topology modification technique via mixing partially reacted substructures (mPRS). The composite material was manufactured and characterized by micro-CT scanning and scanning electron microscopy (SEM). Dynamic single-edge notched bending (d-SENB) experiments were performed on the composites by using a modified split-Hopkinson pressure bar. Each specimen’s fracture process was visualized by ultrafast X-ray imaging. Such in-situ radiography enabled identifying the damage initiation below 50-micron scale and inspecting its propagation through the internal structures of opaque composites, thereby accurately quantifying the composites’ mechanical properties. Furthermore, the identical d-SENB experiments were designed and the digital image correlation (DIC) was employed to monitor the stress wave propagation on the composite specimens. The force and deflection measurements were modified and correlated to the physical damage processes. Besides, quasi-static SENB experiments were conducted to identify the loading rate effects on the composites’ fracture behaviors. The force and deflection history, bending stiffness, energy dissipation, and fracture toughness at different loading rates were quantified and compared. Finally, post-fracture analysis by micro-CT scanning and SEM provided physical observations on the variation of the fracture morphology by different loading rates.

42 ENGINEERING↗
DOE OSTI2025

Experimental data for damage mechanics simulation challenge

While there are many computational approaches for simulating damage in rock and other materials, few have been ground truth tested with either known experimental data or with blind data sets. Here, in this work, we present a bench-mark laboratory data set for a damage mechanics challenge to compare computational approaches on damage evolution in brittle-ductile materials. The samples were fabricated through additive manufacturing to produce repeatable specimens designed to fail in controlled ways. The failure was induced in the samples using a 3-point bending test to produce different Modes such as Mode I and mixed Modes including I-II, I-III and I-II-III Modes to generate a calibration data set and a blind challenge data set. Data collected included spatial and temporal measurements from traditional digital load–displacement sensors, 2D digital image correlation measurement to map surface deformations, 3D X-ray microscopy to ground-truth the crack-failure geometry, and laser profilometry to capture surface roughness. The data sets are available, on a data repository, to the community to advance computational models to improve our ability to predict damage in brittle-ductile materials.

3-point bending↗
DOE OSTI2023

The physics of desiccation cracks 1: Ductile fracturing and dependence on relative humidity

Ductile deformation is ubiquitously found in the shrinkage of geomaterials. The existence of ductility requires elastoplastic mechanics when analyzing the structure deformation under external stress. Here, in this work, we explore the physics of ductile fracturing based on the results from desiccation experiments and triaxial tests. By using the digital image correlation (DIC) method to generate the strain maps of samples undergoing desiccation cracking under different relative humidities, we obtain results showing the previously postulated Cnoidal Wave ductile failure patterns propagating under atmospheric condition-controlled crack velocities. We then correlate these observations with rate-dependent plasticity models calibrated through triaxial tests undergoing several unloading–reloading cycles and velocity stepping. This work demonstrates the necessity to consider ductility in soil cracking, indicating that the formation of crack patterns in soil desiccation is a slow and predictable process.

58 GEOSCIENCES↗
DOE OSTI2023

The physics of desiccation cracks 2: Modeling and prediction of the crack patterns

Here, this paper extends the experimental results of our companion paper by modeling and predicting the onset and pattern formation of desiccation cracks in geomaterials (Ruoyu et al., 2023). Thin-layer silt samples in controlled atmospheric conditions were tested to obtain the surface strain maps with the digital image correlation (DIC) method during dehydration. Support experiments, including consolidation and displacement-controlled triaxial tests, were conducted for the properties of geomaterials. These experimental results were used to validate a viscoplastic theoretical model by comparing cracks and singularities locations that distribute following the Cnoidal wave pattern. A critical value exists in the viscoplastic model that determines the number of singularities, which accurately predicts the number of cracks in the experiment. The critical values contain two crucial parameters: rate sensitivity and λ. Rate sensitivity describes the rate-dependent stress–strain relation, while λ shows the ability of pore pressure redistribution under the external mechanical loading rate. These results provide a new view to analyze the desiccation cracks considering the rate-dependent viscoplasticity.

42 ENGINEERING↗