Search NASA⌕ Search

SEARCH · Search NASA

Results for “grain structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High Throughput Data-Driven Design of Laser-Crystallized 2D MoS 2 Chemical Sensors: A Demonstration for NO 2 Detection

High throughput characterization and processing techniques are becoming increasingly necessary to navigate multivariable, data-driven design challenges for sensors and electronic devices. For two-dimensional materials, device performance is highly dependent upon a vast array of material properties including the number of layers, lattice strain, carrier concentration, defect density, and grain structure. In this work, laser crystallization was used to locally pattern and transform hundreds of regions of amorphous MoS 2 thin films into 2D 2H-MoS 2 . Here a high throughput Raman spectroscopy approach was subsequently used to assess the process-dependent structural and compositional variations for each illuminated region, yielding over 6000 distinct nonresonant, resonant, and polarized Raman spectra. The rapid generation of a comprehensive library of structural and compositional data elucidated important trends between structure–property processing relationships involving laser-crystallized MoS 2 , including the relationships between grain size, grain orientation, and intrinsic strain. Moreover, extensive analysis of structure/property relationships allowed for intelligent design and evaluation of major contributions to device performance in MoS 2 chemical sensors. In particular, it is found that NO 2 sensor performance is strongly dependent on the orientation of the MoS 2 grains relative to the crystal plane.

36 MATERIALS SCIENCE↗
NASA NTRS1967

The dynamics of solid propellant rocket motors.

Solid rocket engine propellant grain structural dynamics including elastic and viscoelastic deformations, stress and shear vibration modes, natural frequency calculations, etc, using Fourier inversions and transforms

VISCOELASTICITY↗
NASA NTRS1983

A nonlinear fracture mechanics approach to the growth of small cracks

An analytical model of crack closure is used to study the crack growth and closure behavior of small cracks in plates and at notches. The calculated crack opening stresses for small and large cracks, together with elastic and elastic plastic fracture mechanics analyses, are used to correlate crack growth rate data. At equivalent elastic stress intensity factor levels, calculations predict that small cracks in plates and at notches should grow faster than large cracks because the applied stress needed to open a small crack is less than that needed to open a large crack. These predictions agree with observed trends in test data. The calculations from the model also imply that many of the stress intensity factor thresholds that are developed in tests with large cracks and with load reduction schemes do not apply to the growth of small cracks. The current calculations are based upon continuum mechanics principles and, thus, some crack size and grain structure exist where the underlying fracture mechanics assumptions become invalid because of material inhomogeneity (grains, inclusions, etc.). Admittedly, much more effort is needed to develop the mechanics of a noncontinuum. Nevertheless, these results indicate the importance of crack closure in predicting the growth of small cracks from large crack data.

Newman, J. C., Jr.↗
DOE OSTI2024

Microstructural and material property changes in severely deformed Eurofer-97

Severe plastic deformation changes the microstructure and properties of steels, which may be favourable for their use in structural components of nuclear reactors. In this study, high-pressure torsion (HPT) was used to refine the grain structure of Eurofer-97, a ferritic/martensitic steel. Electron microscopy and X-ray diffraction were used to characterise the microstructural changes. Following HPT at room temperature to a maximum shear strain of 230, the average grain size reduced by a factor of ~30, with a marked increase in high-angle grain boundaries. Dislocation density also increased by more than one order of magnitude. The thermal stability of the deformed material was investigated via in-situ annealing during synchrotron X-ray diffraction. This revealed substantial recovery between 450 K – 800 K. Irradiation with 20 MeV Fe-ions to ~0.1 dpa caused a 20% reduction in dislocation density compared to the as-deformed material. However, HPT deformation prior to irradiation only had a minor effect in mitigating the irradiation-induced reductions in thermal diffusivity and surface acoustic wave velocity of the material. Microstructural and material property changes are dominated by deformation compared to irradiation. In light of this, the benefits of using HPT to improve the irradiation resistance of Eurofer-97 are limited. These results provide a multi-faceted view of the changes in ferritic/martensitic steels due to severe plastic deformation, and how these changes can be used to alter material properties.

ion-irradiation↗
DOE OSTI2022

Integrated Computational Materials and Mechanical Modeling for Additive Manufacturing of Alloys with Graded Structure Used in Fossil Fuel Power Plants

Wire-arc additive manufacturing (WAAM) has demonstrated its unique capability of producing large-size alloy components with a significantly reduced fabrication time and enhanced geometry design freedom. In this project, the team has developed an ICME (Integrated Computational Materials Engineering) modeling framework, which supports the WAAM of the AUSC (Advanced Ultra-Supercritical) power plant components. The manufacturing design has been applied to Inconel 740H, steel P91, as well as the dissimilar alloy components between steel P91 and Inconel 740H. The ICME model framework is developed by considering two types of modeling. First, mechanistic modeling has been applied to control the printing quality and understand the sequence of the dissimilar printing of the wall structure. The following models have been included in the developed ICME framework: finite element thermal model, grain structure model, residual stress simulation, crystal plasticity model, CALPHAD-based precipitation kinetic model, phase stability prediction, thermal expansion predictive model, and heuristic creep model. Secondary, a physics-based machine learning model has also been developed based on the ICME model structure. The machine learning model development is based on the ICME model prediction with calibration of the experiments. In addition, the WAAM has been utilized as a high-throughput experimental tool rapidly generating a gradient of alloy composition to facilitate experimental database generation for process-structure-property relationships. Such a database directly supported the ICME-enhanced machine learning, which further assisted in intermediate composition block design between P91 and 740H. A high-throughput screening study of the oxidation resistance has been performed based on such high-throughput experimentation. Based on the computational design, several dissimilar alloy manufacturing with post-heat treatment have been performed with a comprehensive evaluation of mechanical performance, including hardness mapping, yield strength, creep resistance. In this project, the single component of P91 and 740H processed by WAAM after heat treatment designed by ICME has demonstrated higher performance in yield strength and creep resistance than the wrought materials. The P91 sample prepared by WAAM with ICME-designed heat treatment performs better than P92 in creep resistance. The designed graded alloy printing with intermediate block shows a promising performance that exceeds the traditional welding. Moreover, the current research indicates the high need for location-specific design analysis with uncertainty quantification, an important topic that deserves more dedicated research. The achievement of this project demonstrated the promising future of WAAM in structural alloy manufacturing for energy power plant development. Successful printing requires synergetic efforts made by manufacturing, mechanical, and materials sciences.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1998

Low-Temperature Friction-Stir Welding of 2024 Aluminum

Solid state friction-stir welding (FSW) has been demonstrated to involve dynamic recrystallization producing ultra-fine, equiaxed grain structures to facilitate superplastic deformation as the welding or joining mechanism. However, the average residual, equiaxed, grain size in the weld zone has ranged from roughly 0.5 micron to slightly more than 10 micron, and the larger weld zone grain sizes have been characterized as residual or static grain growth as a consequence of the temperatures in the weld zone (where center-line temperatures in the FSW of 6061 Al have been shown to be as high as 480C or -0.8 T(sub M) where T(sub M) is the absolute melting temperature)). In addition, the average residual weld zone grain size has been observed to increase near the top of the weld, and to decrease with distance on either side of the weld-zone centerline, an d this corresponds roughly to temperature variations within the weld zone. The residual grain size also generally decreases with decreasing FSW tool rotation speed. These observations are consistent with the general rules for recrystallization where the recrystallized grain size decreases with increasing strain (or deformation) at constant strain rate, or with increasing strain-rate, or with increasing strain rate at constant strain; especially at lower ambient temperatures, (or annealing temperatures). Since the recrystallization temperature also decreases with increasing strain rate, the FSW process is somewhat complicated because the ambient temperature, the frictional heating fraction, and the adiabatic heating fraction )proportional to the product of strain and strain-rate) will all influence both the recrystallization and growth within the FSW zone. Significantly reducing the ambient temperature of the base metal or work pieces to be welded would be expected to reduce the residual weld-zone grain size. The practical consequences of this temperature reduction would be the achievement of low temperature welding. This study compares the residual grain sizes and microstructures in 2024 Al friction-stir welded at room temperature (about 30C and low temperature (-30C).

Benavides, S.↗
NASA NTRS2014

Mercury's Weather-Beaten Surface: Understanding Mercury in the Context of Lunar and Asteroidal Space Weathering Studies

Mercury's regolith, derived from the crustal bedrock, has been altered by a set of space weathering processes. Before we can interpret crustal composition, it is necessary to understand the nature of these surface alterations. The processes that space weather the surface are the same as those that form Mercury's exosphere (micrometeoroid flux and solar wind interactions) and are moderated by the local space environment and the presence of a global magnetic field. To comprehend how space weathering acts on Mercury's regolith, an understanding is needed of how contributing processes act as an interactive system. As no direct information (e.g., from returned samples) is available about how the system of space weathering affects Mercury's regolith, we use as a basis for comparison the current understanding of these same processes on lunar and asteroidal regoliths as well as laboratory simulations. These comparisons suggest that Mercury's regolith is overturned more frequently (though the characteristic surface time for a grain is unknown even relative to the lunar case), more than an order of magnitude more melt and vapor per unit time and unit area is produced by impact processes than on the Moon (creating a higher glass content via grain coatings and agglutinates), the degree of surface irradiation is comparable to or greater than that on the Moon, and photon irradiation is up to an order of magnitude greater (creating amorphous grain rims, chemically reducing the upper layers of grains to produce nanometer scale particles of metallic iron, and depleting surface grains in volatile elements and alkali metals). The processes that chemically reduce the surface and produce nanometer-scale particles on Mercury are suggested to be more effective than similar processes on the Moon. Estimated abundances of nanometer-scale particles can account for Mercury's dark surface relative to that of the Moon without requiring macroscopic grains of opaque minerals. The presence of nanometer-scale particles may also account for Mercury's relatively featureless visible-near-infrared reflectance spectra. Characteristics of material returned from asteroid 25143 Itokawa demonstrate that this nanometer-scale material need not be pure iron, raising the possibility that the nanometer-scale material on Mercury may have a composition different from iron metal [such as (Fe,Mg)S]. The expected depletion of volatiles and particularly alkali metals from solar-wind interaction processes are inconsistent with the detection of sodium, potassium, and sulfur within the regolith. One plausible explanation invokes a larger fine fraction (grain size less than 45 micron) and more radiation-damaged grains than in the lunar surface material to create a regolith that is a more efficient reservoir for these volatiles. By this view the volatile elements detected are present not only within the grain structures, but also as adsorbates within the regolith and deposits on the surfaces of the regolith grains. The comparisons with findings from the Moon and asteroids provide a basis for predicting how compositional modifications induced by space weathering have affected Mercury's surface composition.

Weathering↗
DOE OSTI2023

Microstructure-process relationships in monolithic U-10Mo fuel foil single-pass rolling: A parametric simulation study

In this work, a previously validated coupling of Kinetic Monte Carlo (KMC) Potts Model and finite element method (FEM) simulations was implemented to investigate the effects of microstructural features in as-cast and homogenized monolithic U-10Mo foils on the emergent microstructure after rolling and reheating. Parameters that could potentially affect recrystallization behavior of the rolled U-10Mo foils were considered: grain size distribution, uranium carbide (UC) size distribution, UC volume fraction, spatial distribution of UC, and rolling reduction magnitude. Grain structure and the magnitude of rolling reduction have the strongest influence on recrystallization kinetics and the fabricated grain size distribution. The UC distribution had only a weak effect on the recrystallization kinetics and final microstructures. While particle-stimulated nucleation (PSN) occurred in simulation more frequently as grain size increased, its incidence did not appear to considerably affect the recrystallization kinetics or grain size distribution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Ductility in rapidly solidified NiAl

An attempt is made to refine the grain structure of equiatomic NiAl by means of rapid solidification processing, and to examine the effect of small grain size on room temperature ductility. Free melt spinning was used to produce the rapidly solidified material. Room temperature bend testing of both as-spun and heat-treated NiAl ribbon was conducted by free bending the ribbon around a mandrel of successively smaller diameter until failure occurred. Room-temperature plastic deformation was exhibited both before and after a 1-h heat treatment at 1000 C. Heat treatment increased the observed ductility.

Gaydosh, D. J.↗
DOE OSTI2022

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography (μCT) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μCT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. Further, a new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Discovery, Design, Synthesis and Testing of High Performance Structural Alloys (Final Technical Report)

The overarching goal of this project is to understand the phase stability and mechanical behavior of non-stoichiometric multi-principal element alloy (MPEA) materials. In order to identify suitable alloys, we plan to use a combinatorial thin film screening approach, in collaboration with scientists at Lawrence Berkeley National Laboratory who are performing computational work as well as complementary experimental work. Specific tasks within the scope of this project include the fabrication, using thin film deposition from six sputtering targets, of combinatorial samples with multi-dimensional gradients in composition and microstructure. These samples are studied to screen MPEA systems for promising candidate alloys with specific composition(s), based on characterization of composition, structure and mechanical behavior across the thin film. We want to produce single-phase MPEAs with chemical homogeneity in a given thin film region, simple grain structures, and no intermetallic phases present. Gradient films facilitate first-pass screening for desirable characteristics and inform the next stage of work that involves fabrication of bulk MPEA specimens for (tensile) mechanical testing and characterization. To make the bulk alloys, metal (elemental) pieces are melted to form MPEAs, followed by heat treatment to homogenize the composition and microstructure. A subset of alloys is also cast, using vacuum arc melting, to yield larger samples (diameter ~1 cm and length ~5-10 cm) and these allow us to assess viability of scale-up for the alloys in structural applications. Further processing plans include rolling and heat treatment to recrystallize selected bulk MPEAs and grow grains to different extents, in order to investigate size effects in the mechanical behavior of MPEAs. Microspecimen testing will be performed (primarily in tension) to assess the mechanical behavior over a range of temperatures. The deformation microstructure of mechanically tested alloys will be characterized using transmission electron microscopy (TEM) to provide a scientific basis for understanding the structure-property relationships in MPEA mechanical behavior.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Characterization and properties of controlled nucleation thermochemical deposited /CNTD/ silicon carbide

Results are presented for an investigation designed to characterize the microstructure of controlled nucleation thermomechanical deposition (CNTD) produced SiC material with respect to grain structure, stoichiometry, phase analysis, etc., and to evaluate the room-temperature and high-temperature fracture and oxidation behavior. By using the CNTD process, ultrafine-grained SiC is deposited on tungsten wires as substrates, with superior surface smoothness and without the macrocolumnar growth commonly observed in conventional CVD materials. The results suggest that the high-purity, fully dense, and stable grain size SiC material produced by CNTD shows potential for high-temperature structural applications, provided that pertinent problems are resolved.

Dutta, S.↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Residual stress and microstructure in IN718-René41 graded superalloy fabricated by laser blown directed energy deposition

Additively printed Ni-based superalloy with a compositionally graded transition from IN718 to René41 was fabricated by laser blown-powder directed energy deposition (DED/LB-M), with the goals of meeting location-specific temperature capability and reducing component cost for hot gas path turbine components. Residual stress distribution in thin wall specimens with three sets of DED build parameters in the as-built and stress-relieved states was measured by neutron diffraction. For calculating residual stress, the calculated d0 method was found to be more appropriate as stress-free reference than using the lattice spacing measured from the stress-relief heat treated specimens. Longer dwell time (lower interpass temperature), higher energy input, smaller layer thickness resulted in a higher magnitude of tensile residual stresses at edges and compressive residual stresses at center of the specimens. The residual stress results did not show a strong dependence on graded compositions, indicating that the residual stress build-up was more geometry and process dependent. Non-destructive neutron imaging based on the attenuation coefficient qualitatively visualized the compositional variation in the bulk and showed good agreement with quantitative Electron Probe Micro-Analysis (EPMA) measurement. Grain structure, texture, and residual plastic strain along the build direction were characterized by Electron Backscatter Diffraction (EBSD). Long columnar grains with (001) preferred grain orientation were dominant along the build direction. Compositional change did not show an obvious effect on the epitaxial growth of dendrites and the continuation of the columnar grains. Residual plastic strain was relatively low in the as-built specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding Uncertainty in Microstructure Evolution and Constitutive Properties in Additive Process Modeling

Coupled process–microstructure–property modeling, and understanding the sources of uncertainty and their propagation toward error in part property prediction, are key steps toward full utilization of additive manufacturing (AM) for predictable quality part development. The OpenFOAM model for process conditions, the ExaCA model for as-solidified grain structure, and the ExaConstit model for constitutive mechanical properties are used as part of the ExaAM modeling framework to examine a few of the various sources of uncertainty in the modeling workflow. In addition to “random” uncertainty (due to random number generation in the orientations and locations of grains present), the heterogeneous nucleation density N 0 and the mean substrate grain spacing S 0 are varied to examine their impact of grain area development as a function of build height in the simulated microstructure. While mean grain area after 1 mm of build is found to be sensitive to N 0 and S 0 , particularly at small N 0 and large S 0 (despite some convergence toward similar values), the resulting grain shapes and overall textures develop in a reasonably similar manner. As a result of these similar textures, ExaConstit simulation using ExaCA representative volume elements (RVEs) from various permutations of N 0 , S 0 , and location within the build resulted in similar yield stress, stress–strain curve shape, and stress triaxiality distributions. It is concluded that for this particular material and scan pattern, 15 layers is sufficient for ExaCA texture and ExaConstit predicted properties to become relatively independent of additional layer simulation, provided that reasonable estimates for N 0 and S 0 are used. However, additional layers of ExaCA will need to be run to obtain mean grain areas independent of build height and baseplate structure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiple experimental studies of pore structure and mineral grain sizes of the Woodford shale in southern Oklahoma, USA

Pore structure study is an important part of unconventional shale reservoir characterization, since the pore system provides the primary petroleum storage space and fluid flow pathways. Previous studies have suggested that the pore structure is related to the total organic carbon (TOC) content, mineral compositions, and the maturity of the organic matter (OM). However, few studies have focused on the mineral grains, the primary grains being deposited but before cementation, which are the building blocks of shale. Eight Woodford Shale outcrop samples from southern Oklahoma were chosen to study the effects of mineral grain size on the pore structure characterization, using multiple and complementary experimental approaches, including laser diffraction, mineralogy, TOC, pyrolysis, liquid immersion porosimetry, mercury intrusion porosimetry, gas physisorption, (ultra) small angle X-ray scattering, scanning electron microscopy, and spontaneous imbibition. The results from different experiments of eight samples show that the Woodford Shale has the mean mineral grain diameters at 3–6 μm, a wide range of porosity at 3–40% and pore diameters at 50–1,000 nm, and various pore connectivity. Grain size variation was probably caused by the sea-level fluctuation during its deposition, which affect the porosity, pore size distribution, and pore connectivity. With decreasing mineral grain sizes, the porosity tends to increase while the pore connectivity worsens. The results also indicate that OM and carbonates in this low-maturity Woodford Shale could block the pores and decrease the porosity. Coupling with the grain size analyses, the control of depositional environment on grain sizes and subsequent effects on pore structure is identified. The pore structure characteristics over a wide pore-diameter range provided by multiple experiments could improve the understanding of storage space and fluid flow in the Woodford Shale to further increase its petroleum production.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Oxidized structure and Compositional properties of 1144 phase FBS by analytical electron microscopy

The 1144 phase (Ae1A1Fe4As4) shows a strong advantage of engineering fabrication among Fe Iron)-based superconductor (FBS) family due to the robustness of its superconducting properties with respect to chemical inhomogeneities, granted by its uniform crystalline-layered structure. This regularity is furthermore associated to crystalline defects capable of acting as efficient pinning centers, which high critical currents achieved at high fields for these superconductors. Like other FBS phases, its lossless current-carrying capability can be remarkably degraded by distractions at grain boundaries (GBs). GB oxidation is an issue of upmost importance to the realization of the practical FBS application for high field (> 20T) magnet. In this study, we explore oxidized grain boundary and intrinsic grain structural properties of 1144 polycrystalline samples by applying analytical electron microscopy such as atomic resolution scanning transmission electron microscopy and atom probe tomography. These structural properties of samples produced by a mechanochemically assisted synthesis are evaluated following the degradation of superconducting properties due to oxidation. We observe a strong correlation between the contamination at grain boundaries and the decrease of transport properties of the bulk sample, while the crystallin structure seems to be not affected by the oxidation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Microstructure refinement of hot deformed Dy-free NdFeB magnets through a novel cold sintering approach by pressure-assisted spark plasma sintering

Anisotropic fine-grained Dy-free NdFeB high-performance magnets were produced using a novel cold sintering approach by pressure-assisted spark plasma sintering (SPS). The NdFeB nanocrystalline ribbon powders were subjected to cold sintering below 450 °C using pressure-assisted SPS, followed by hot deformation at 710 °C and 810 °C via SPS. Results indicate that cold sintering below 450 °C effectively restricts grain growth in the NdFeB magnets, yielding sub-100 nm scale grains across both fine-grained regions and most coarse-grained regions. The refined grain structure achieved through cold sintering allows for a lower hot deformation temperature as compared with the magnet by conventional sintering, as finer grains allow easier deformation and grain sliding/rotation. This process produces a highly fine-grained and anisotropic microstructure to achieve high magnetic performance (i.e., high intrinsic coercivity, remanence, and maximum energy product) in the magnets. The cold sintering (at 350 °C) and lower hot deformation temperatures required (e.g., 710 °C) help control grain coarsening and limit grain size that is commensurate with the size of a single magnetic domain of the Nd 2 Fe 14 B magnetic matrix phase, resulting in high intrinsic coercivity (H ci =11.4 kOe). Furthermore, the reduced hot deformation temperature mitigates the formation of coarse grain bands, leading to improved magnetic properties, specifically an increased remanence (B r = 14.3 kGs) and a high maximum energy product ((BH) max = 48 MGOe). In conclusion, cold sintered hot deformed NdFeB magnet also shows good thermal stability with reversible temperature coefficient α(B r )= -0.097 %/K and α(H ci )= -0.616 %/K at elevated temperatures up to 400 K.

Cold Sintering↗