Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite behavior models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Quantifying the Temperature Dependence of the Multi-Species, Multi-Reaction Model. Part 1: Parameterization for a Meso-Carbon Micro-Bead Graphite

In this work, the temperature impact on the Multi-Species, Multi-Reaction (MSMR) model is studied. This is accomplished by acquiring data from slow rate lithiation and delithiation of a meso-carbon micro-bead (MCMB) graphite. The MSMR model is used to simulate linear-sweep voltammetry data of a porous electrode composed of graphite, and because the electrode is close to a state of dynamic equilibrium, the peaks in the differential voltage spectroscopy plot can be analyzed. Through this analysis, the temperature impact on the total fraction of available host sites in a particular MSMR gallery (X j ), the impact on the reference potential (U° j ), and the impact on the parameter detailing the deviation from Nernstian behavior ( ω j ) can be found. This is the first time the temperature dependence of the MSMR parameters have been experimentally analyzed. In Part 2, the impact of the temperature dependence of the MSMR parameters on the entropy coefficient of an intercalation material will be studied.

Paul, Abigail (ORCID:0000000172892069)↗

Deep Burn: Development of Transuranic Fuel for High-Temperature Helium-Cooled Reactors- Monthly Highlights September 2010

The DB Program monthly highlights report for August 2010, ORNL/TM-2010/184, was distributed to program participants by email on September 17. This report discusses: (1) Core and Fuel Analysis - (a) Core Design Optimization in the HTR (high temperature helium-cooled reactor) Prismatic Design (Logos), (b) Core Design Optimization in the HTR Pebble Bed Design (INL), (c) Microfuel analysis for the DB HTR (INL, GA, Logos); (2) Spent Fuel Management - (a) TRISO (tri-structural isotropic) repository behavior (UNLV), (b) Repository performance of TRISO fuel (UCB); (3) Fuel Cycle Integration of the HTR (high temperature helium-cooled reactor) - Synergy with other reactor fuel cycles (GA, Logos); (4) TRU (transuranic elements) HTR Fuel Qualification - (a) Thermochemical Modeling, (b) Actinide and Fission Product Transport, (c) Radiation Damage and Properties; (5) HTR Spent Fuel Recycle - (a) TRU Kernel Development (ORNL), (b) Coating Development (ORNL), (c) Characterization Development and Support, (d) ZrC Properties and Handbook; and (6) HTR Fuel Recycle - (a) Graphite Recycle (ORNL), (b) Aqueous Reprocessing, (c) Pyrochemical Reprocessing METROX (metal recovery from oxide fuel) Process Development (ANL).

Snead, Lance Lewis↗

Correlation of Structural Analysis and Test Results for the McDonnell Douglas Stitched/RFI All-Composite Wing Stub Box

The analytical and experimental results of an all-composite wing stub box are presented in this report. The wing stub box, which is representative of an inboard portion of a commercial transport high-aspect-ratio wing, was fabricated from stitched graphite-epoxy material with a Resin Film Infusion manufacturing process. The wing stub box was designed and constructed by the McDonnell Douglas Aerospace Company as part of the NASA Advanced Composites Technology program. The test article contained metallic load-introduction structures on the inboard and outboard ends of the graphite-epoxy wing stub box. The root end of the inboard load introduction structure was attached to a vertical reaction structure, and an upward load was applied to the outermost tip of the outboard load introduction structure to induce bending of the wing stub box. A finite element model was created in which the center portion of the wing-stub-box upper cover panel was modeled with a refined mesh. The refined mesh was required to represent properly the geometrically nonlinear structural behavior of the upper cover panel and to predict accurately the strains in the stringer webs of the stiffened upper cover panel. The analytical and experimental results for deflections and strains are in good agreement.

Wang, John T.↗

Scaling effects in the impact response of graphite-epoxy composite beams

In support of crashworthiness studies on composite airframes and substructure, an experimental and analytical study was conducted to characterize size effects in the large deflection response of scale model graphite-epoxy beams subjected to impact. Scale model beams of 1/2, 2/3, 3/4, 5/6, and full scale were constructed of four different laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic. The beam specimens were subjected to eccentric axial impact loads which were scaled to provide homologous beam responses. Comparisons of the load and strain time histories between the scale model beams and the prototype should verify the scale law and demonstrate the use of scale model testing for determining impact behavior of composite structures. The nonlinear structural analysis finite element program DYCAST (DYnamic Crash Analysis of STructures) was used to model the beam response. DYCAST analysis predictions of beam strain response are compared to experimental data and the results are presented.

Jackson, Karen E.↗

The induction of a graphite-like phase on diamond films by a Fe-coating/post-annealing process to improve their electron field emission properties

The electron field emission (EFE) process for diamond films was tremendously enhanced by Fe-coating and post-annealing processes. Microstructural analysis indicates that the mechanism for the improvement in the EFE process is the formation of nanographites with good crystallinity that surround the Fe (or Fe{sub 3}C) nanoclusters. Presumably the nanographites were formed via the reaction of Fe clusters with diamond films, viz. by the dissolution of carbons into Fe (or Fe{sub 3}C) clusters and the reprecipitation of carbon species to the surface of the clusters, a process similar to the growth of carbon nanotubes via Fe clusters as catalyst. Not only is a sufficiently high post-annealing temperature (900 deg. C) required but also a highly active reducing atmosphere (NH{sub 3}) is needed to give a proper microstructure for enhancing the EFE process. The best EFE properties are obtained by post-annealing the Fe-coated diamond films at 900 deg. C in an NH{sub 3} environment for 5 min. The EFE behavior of the films can be turned on at E{sub 0} = 1.9 V/{mu}m, attaining a large EFE current density of 315 {mu}A/cm{sup 2} at an applied field of 8.8 V/{mu}m (extrapolation using the Fowler-Nordheim model leads to J{sub e} = 40.7 mA/cm{sup 2} at a 20 V/{mu}m applied field).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

3D Flow and Temperature Analysis of Filling a Plutonium Mold (Revision 1) [Poster]

The plutonium foundry at Los Alamos National Laboratory casts products for various special nuclear applications. However, plutonium’s radioactivity, material properties, and security constraints complicate the ability to perform experimental analysis of mold behavior. The Manufacturing Engineering and Technologies (MET-2) group previously developed a graphite mold to vacuum cast small plutonium disks to be used by the Department of Homeland Security as point sources for radiation sensor testing. A two-stage pouring basin consisting of a funnel and an angled cavity directs the liquid into a vertical runner. A stack of ten disk castings connect to the runner by horizontal gates. Volumetric flow rates were implemented to limit overflow into the funnel and minimize foundry returns. Models using Flow-3D computational fluid dynamics software are employed here to determine liquid Pu flow paths, optimal pour regimes, temperature changes, and pressure variations.

36 MATERIALS SCIENCE↗

Experimental Plan for EDF Energy Creep Rabbit Graphite Irradiations- Rev. 2 (replaces Rev. 0 ORNL/TM/2013/49)

The experimental results obtained here will assist in the development and validation of future models of irradiation induced creep of graphite by providing the following data: Inert creep stain data from low to lifetime AGR fluence Inert creep-property data (especially CTE) from low to lifetime AGR fluence Effect of oxidation on creep modulus (by indirect comparison with experiment 1 and direct comparison with experiment 3 NB. Experiment 1 and 3 are not covered here) Data to develop a mechanistic understanding, including: appropriate creep modulus (including pinning and high dose effects on structure), investigation of CTE-creep strain behavior under inert conditions oInformation on the effect of applied stress/creep strain on crystallite orientation (requires XRD), effect of creep strain on micro-porosity (requires tomography & microscopy) This document describes the experimental work planned to meet the requirements of project technical specification and EDF Energy requests for additional Pre-IE work. The PIE work is described in detail in this revision (Section 8 and 9).

Burchell, Timothy D.↗

The behavior of delaminations in composite plates - Analytical and experimental results

The behavior of elliptical sublaminates created by delaminations in composite plates was investigated for plates subjected to in-plane compressive, shear, and thermal loads. The axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed which provides the stresses, strains, and displacements of the sublaminate, and the loads applied to the plate at which the sublaminate buckles and at which it grows in size. A series of experiments was conducted on sandwich plates made of Fiberite T300/976 graphite-epoxy laminates bonded to an aluminum honeycomb core. Teflon film in either a circle or an ellipse was embedded in the laminate, simulating the presence of a delamination. Each plate was loaded in compression, and the load-strain history of the sublaminate, the sublaminate buckling load, and the sublaminate growth load were measured. The predictions of the model agreed reasonably well with the data.

Peck, Scott O.↗

Integrated Approach to Fluoride High Temperature Reactor Technology and Licensing Challenges (FHR-IRP)

This document constitutes progress made on this project by the Georgia Tech led Integrated Approach to Fluoride High Temperature Reactor Technology and Licensing Challenges (FHR-IRP). This is the first draft of the project final report. Chapter 3 is focused on Tritium management. Tritium management in Fluoride-salt High-temperature Reactors (FHRs) presents a major operational concern and a significant challenge. Tritium is generated via multiple pathways including various interactions in fuel and structural materials, as well as coolant (primarily interaction with lithium and beryllium), leading to a complex evolution and spatial distribution of tritium generation rate. FHR generates orders of magnitude more tritium than in LWRs, and has potential for a significant release, via permeation through structural materials (due to high temperature), and through heat exchanger(s). Therefore, accurate estimate is necessary. For that purpose relevant tritium production pathways were identified. A methodology to obtain space-time dependent tritium generation rate was developed and implemented, employing SCALE and MCNP codes. Detailed models of the reference Advanced High Temperature Reactor (AHTR) design were developed. A multi-parametric metrics was introduced to capture relevant tritium production indicators, including the instantaneous tritium production rate, total tritium production (neglecting subsequent decay), and accumulated tritium production (accounting for the decay). The obtained results will inform tritium management, including the sizing of the components, and to gain insight on the impact of the core design parameters on tritium generation rates. Research effort on Liquid Salt Impurity Removal, Redox and Corrosion Control is discussed in Chapter 4. Section 4.1 is an introduction chapter. Based on the current available knowledge and operation experience on previous MSRs and other types of nuclear reactors, the report identifies the major impurities that are related to either material compatibility, salt properties or radioactive source terms, and the potential contamination sources of these impurities, their transport in the primary coolant loop and available cleanup methodologies for a particular group of impurity. In section 4.2, the available purification methods were discussed, including the liquid/liquid extraction using liquid Bi-Li which has been applied in MSBR and electrochemical purification which is developed based on Pyroprocessing. In this section, the new multi-stage and multi-salt-component was developed and discussed. Section 4.3 discussed the redox potential control for salt chemistry and corrosion mitigation, including the control theory and the soluble/soluble buffer control method. The section also developed method on how to analyze soluble/soluble redox reaction in a molten salt system and designed an electrochemical sensor for redox potential control. Corrosion models were also reported in this section. Section 4.4 focused on how to measure the fundamental properties in a molten salt. As an example, the section focused on La fluoride in the molten salt. The section developed methods on how analyze electrochemical measurement data to obtain the fundamental properties including the redox potential, diffusion coefficient and exchange current density. All these fundamental information is important for salt purification system development. Section 4.5 focused on measurements of corrosion products in the salts. Because of the different behaviors between Cr and La in the salt, new analysis method for Cr fluorides in the salt was developed. Some results for Fe fluoride in the salt and corrosion measurements were also reported. Section 4.6 demonstrated the separation of oxide from the salt. This section also measured the solubility of La 2 O 3 in the salt as function of temperature. Section 4.7 focused on the separation of La and Ce from the molten salt. These two elements were selected because La was found to be separated by using inert electrode, while for separation of Ce, reactive electrode must be selected. Section 4.8 demonstrated the separation iodine ions from the molten salt. Two kinds of working electrode materials (metal W and graphite) were investigated. Section 4.9 focused on the fundamental data of fission products and actinides in liquid Bi. The chapter reviewed the available data, then based a CALPHAD model, the available data were broadened to the concentration-dependent cases.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Nature of very small grains - PAH molecules or silicates?

The predictions of the model of Puget et al. (1985) for the emission from Very Small Grains (VSGs) including both graphitic and silicate components are compared with published 8-13-micron observations of astronomical sources. The VSGs are found to be mainly graphitic and an upper limit is placed on the relative mass of silicates based on lack of the 9.7-micron silicate emission feature on M 82 and NGC 2023. This dissymetry in the composition of VSGs supports the suggestion that they are formed in grain-grain collisions where the behaviors of graphite and silicate grains are expected to be quite different.

Desert, F. X.↗

Kinetics of Chronic Oxidation of NBG-17 Nuclear Graphite by Water Vapor

This report presents the results of kinetic measurements during accelerated oxidation tests of NBG-17 nuclear graphite by low concentration of water vapor and hydrogen in ultra-high purity helium. The objective is to determine the parameters in the Langmuir-Hinshelwood (L-H) equation describing the oxidation kinetics of nuclear graphite in the helium coolant of high temperature gas-cooled reactors (HTGR). Although the helium coolant chemistry is strictly controlled during normal operating conditions, trace amounts of moisture (predictably < 0.2 ppm) cannot be avoided. Prolonged exposure of graphite components to water vapor at high temperature will cause very slow (chronic) oxidation over the lifetime of graphite components. This behavior must be understood and predicted for the design and safe operation of gas-cooled nuclear reactors. The results reported here show that, in general, oxidation by water of graphite NBG-17 obeys the L-H mechanism, previously documented for other graphite grades. However, the characteristic kinetic parameters that best describe oxidation rates measured for graphite NBG-17 are different than those reported previously for grades H-451 (General Atomics, 1978) and PCEA (ORNL, 2013). In some specific conditions, certain deviations from the generally accepted L-H model were observed for graphite NBG-17. This graphite is manufactured in Germany by SGL Carbon Group and is a possible candidate for the fuel elements and reflector blocks of HTGR.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Progress Report on Graphite-Salt Intrusion Studies

The document reports on the design, construction, testing and initial operation of the ORNL graphite intrusion system with pressurized molten salts. This technical memorandum is responsive to work package AT-20OR04060203, “Graphite-Salt Studies” —ORNL”, and fulfills Milestone M3AT20OR040602035 “Report on graphite-salt intrusion studies”.The report outlines the procedure of graphite intrusion experiments, which follows the ASTM standard guidance, and the procedures of other characterization measurements of graphite physical properties, also based on ASTM standard methods. A set of 12 graphite grades of various origin and properties went through preliminary characterizations, and six of them were further selected for intrusion experiments with molten FLiNaK. The results are discussed in the context of graphite physical properties and are compared with a several results from literature. The correlation between molten salt impregnation and mercury intrusion, first proposed by MSRE scientists, is discussed in detail. Pending collection of more data, the mercury intrusion porosimetry technique may possibly be used as a rapid method for screening and down selection of graphite grades with extremely low salt intrusion, as required for operation in molten salt reactors. This new system will generate data non only on intrusion behavior, but will also generate a wide range of salt- impregnated graphite samples that will be further analyzed with advanced characterization techniques for better understanding of the effect of salt intrusion on the properties of nuclear graphite. It expected that these results and future results obtained with this system will help advance our understanding of the factors controlling the extent of salt penetration in graphite and of the relationship with intrinsic structural properties of various grades. Together, correlating direct measurements results and graphite structural properties should allow development of a predictable model that could be used for selection and qualification of optimal graphite grades, tailored to design operation conditions and molten salt properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of a unidirectional, symmetric buffer strip laminate with damage

A method for predicting the fracture behavior of hybrid buffer strip laminates is presented in which the classical shear-lag model is used to represent the shear stress distribution between adjacent fibers. The method is demonstrated by applying it to a notched graphite/epoxy laminate, and the results show clearly the manner in which the most efficient combination of buffer strip properties can be selected in order to arrest the crack. The ultimate failure stress of the laminate is plotted vs the buffer strip width. It is shown that in the case of graphite-epoxy and S-glass epoxy laminates, the optimum buffer strip spacing to width ratio should be about four to one.

Dharani, L. R.↗

Postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected curved stiffened graphite-epoxy panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. Each panel had four equally-spaced I-shaped stiffeners and 16-ply quasi-isotropic skins. Panels with three different stiffener spacings were tested. Failure of all panels initiated in a skin-stiffener interface region. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical postbuckling test results up to failure. The analytical modeling detail necessary to predict accurately the response of the panel is described. Measured initial geometric imperfections were included in the postbuckling analysis.

Knight, N. F., Jr.↗

Long-life assessment of graphite epoxy materials for Space Station Freedom pressure vessels

Graphite/epoxy composite overwrapped pressure vessels are being considered for use on Space Station Freedom because of their light weight and high efficiency. These composite pressure vessels weigh roughly one-third of comparable all-metal aluminum pressure vessels, and could result in a 15,000-lb weight saving for the propulsion and fluid management and distribution systems. These vessels must resist failures under sustained pressure loads for crew safety considerations and adequate protection of the space structure during their 30-yr life. Weibull statistical analysis techniques have been applied, and a model developed, for predicting long-term stress-rupture behavior based on published short-term test data on composite strands and pressure vessels. Graphite/epoxy materials are calculated to have a 99.99-percent probability of surviving stress rupture for 30 yr under a sustained load of 50 percent ultimate failure strength. Stress-rupture lifetimes are predicted to increase as the size of the pressure vessels increases in support of the viscoelastic load-transfer mechanism proposed for stress rupture of fiber/epoxy composite materials.

Thomas, Donald A.↗

Creep rupture behavior of unidirectional advanced composites

A 'material modeling' methodology for predicting the creep rupture behavior of unidirectional advanced composites is proposed. In this approach the parameters (obtained from short-term tests) required to make the predictions are the three principal creep compliance master curves and their corresponding quasi-static strengths tested at room temperature (22 C). Using these parameters in conjunction with a failure criterion, creep rupture envelopes can be generated for any combination of in-plane loading conditions and ambient temperature. The analysis was validated experimentally for one composite system, the T300/934 graphite-epoxy system. This was done by performing short-term creep tests (to generate the principal creep compliance master curves with the time-temperature superposition principle) and relatively long-term creep rupture tensile tests of off-axis specimens at 180 C. Good to reasonable agreement between experimental and analytical results is observed.

Yeow, Y. T.↗

An SECM-Based Spot Analysis for Redoxmer-Electrode Kinetics: Identifying Redox Asymmetries on Model Graphitic Carbon Interfaces

The fundamental process in non-aqueous redox flow battery (NRFB) operation revolves around electron transfer (ET) between a current collector electrode and redox-active organic molecules (redoxmers) in solution. Here, we present an approach utilizing scanning electrochemical microscopy (SECM) to evaluate interfacial ET kinetics between redoxmers and various electrode materials of interest at desired locations. This spot-analysis method relies on the measurement of heterogeneous electron transfer rate constants (k f or k b ) as a function of applied potential (E-E 0 '). As demonstrated by COMSOL simulations, this method enables the quantification of Butler-Volmer kinetic parameters, the standard heterogeneous rate constant, k 0 , and the transfer coefficient, α. Our method enabled the identification of inherent asymmetries in the ET kinetics arising during the reduction of ferrocene-based redoxmers, compared to their oxidation which displayed faster rate constants. Similar behavior was observed on a wide variety of carbon electrodes such as multi-layer graphene, highly ordered pyrolytic graphite, glassy carbon, and chemical vapor deposition-grown graphite films. However, aqueous systems and Pt do not exhibit such kinetic effects. Our analysis suggests that differential adsorption of the redoxmers is insufficient to account for our observations. Displaying a greater versatility than conventional electroanalytical methods, we demonstrate the operation of our spot analysis at concentrations up to 100 mM of redoxmer over graphite films. Looking forward, our method can be used to assess non-idealities in a variety of redoxmer/electrode/solvent systems with quantitative evaluation of kinetics for applications in redox-flow battery research.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measurement of Fission Product Concentration Profiles in AGR-3/4 TRISO Fuel Graphitic Matrix and Nuclear Graphites

The third Advanced Gas Reactor (AGR) irradiation experiment, AGR-3/4, was designed to investigate the migration of fission products in fuel compact graphitic matrix and reactor graphite components. Using destructive methods, radial fission product concentration profiles were measured for gamma-emitting fission products (e.g., Ag-110m, Cs-134, and Eu-154) and beta-emitting Sr-90 in irradiated graphitic and graphite components from six different AGR-3/4 irradiation capsules. These new measured concentration profiles can now be compared to non-destructive measurements and fission product transport simulations and will be used to derive new diffusivities and sorptivities to support refinement of fission product transport models and high-temperature gas-cooled reactor (HTGR) source-term analyses. Each capsule in the AGR-3/4 experiment had four fuel compacts in the middle of two concentric rings of graphitic matrix material, PCEA graphite, or IG-110 graphite. In addition to the approximately 1898 tristructural isotropic (TRISO) coated particles in each compact, there were 20 designed to fail (DTF) particles coated only in pyrocarbon so that they released fission products into the surrounding cylindrical rings of carbonaceous materials. Destructive sampling of the rings involved machining/milling material from around the circumference of the rings, collecting that material, and performing radiochemical analyses on it. Milling operations were performed in multiple steps or segments, and each segment was generally 0.508 mm (0.020 in) thick. Knowing the radial position at which each segment was milled, the volume of the milled material at each segment, and the fission product content in each segment, the radial fission product concentrations were constructed for select isotopes in each ring. Ag-110m profiles had the most variation. Some profiles were peaked at an inner or outer surface. Some were peaked at the middle of the ring wall thickness. Some increased radially outward, and some decreased radially outward. These types of variations and the fact that the measured profiles do not generally compare favorably with the transport model employed for AGR-3/4 may adversely impact the ability to extract reasonable transport parameters for this isotope. In many cases, the Cs-134 profiles decreased somewhat linearly in the outward radial direction, and in cursory comparisons, the shapes of these profiles appeared similar to those from model predictions. The step changes in concentration across the inner-outer ring gap were generally consistent with the model predictions as well. In some cases, there were local maxima in concentration at the outer surface of the rings. This suggests that fission products could have transported in the small gaps between the inner ring and the outer ring and between the outer ring and the sink ring such that some portion of a given fission product can bypass diffusion through the ring itself. The analysis of the small nubs on the outer surfaces of some of the outer rings revealed fission product concentrations in the nubs that were often higher than in the outermost segments of the rings. This further supports the hypothesis that short-circuit, gap transport occurred, causing relatively high surface concentrations on the outer surfaces of the rings. Eu-154 and Sr-90 profiles tend to have very similar shapes, suggesting that they transport via the same mechanisms. The observed profiles were indicative of a transport process where the isotopes are sorbed on the inner surface of the ring, but diffusion into the ring from that surface is quite slow. Some elevated concentrations of Sr-90 (relative to Eu-154) on the outer surface of a ring suggested that rapid, gas-gap transport of gaseous precursor Kr-90 and volatile Rb-90 could have occurred prior to their decaying to Sr-90. Overall, the Eu 154 and Sr-90 profiles were still very similar, which indicates that the transport of short-lived Sr-90 precursors is not a major effect. In some capsules, the qualitative Sr-90 behavior across the ring gaps was consistent with the model (using the available legacy Sr-90 transport parameters), but in other capsules the model was inconsistent with the measurements and seems to underestimate the amount of Sr-90 in the outer rings. The total ring Sr-90 inventories were estimated for all the rings that were subject to physical sampling. These results will be used to adjust the predicted particle and/or compact releases used in the AGR-3/4 fission product transport model. Given the different irradiation temperatures among the capsules and the rings, it was not possible to discern fundamental differences in the transport of isotopes within the different carbon materials, i.e., graphitic matrix, IG-110, or PCEA. It may be possible to do this in the course of determining transport from the concentration profiles in future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗