SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The research accomplishments under this grant were very extensive in the areas of the high temperature behavior of ceramics, ceramic composites and testing standards for these materials. Rather than try to summarize all this research I have enclosed research papers and reports which were completed with the funding provided by the grant.
Zirconia coated sapphire reinforced alumina matrix composites have been tested both after heat treatment to 1400 C and at temperatures ranging from 800 C to 1200 C in. air. Interfacial shear stress has also been measured with fiber pushout tests performed in air at room temperature, 800 C and 1OOO C. Matrix crack spacing was measured for the tensile tested composites and used to estimate interfacial shear stress up to 1200 C. Electron microscopy was used to determine the source of fiber fracture and to study interfacial failure within the composite.
Gas turbine components such as combustor liners or turbine vanes are subject to regions of high stress-concentration, e.g., attachment to the frame or at cooling holes. Ceramic matrix composites (CMCs) are potential materials for high temperature applications in gas turbines. They offer some capability to relieve stress at regions of high stress-concentration via matrix damage accumulation. In this study notch sensitivity was examined for woven SiC fiber reinforced, melt-infiltrated SiC matrix composites with a BN interphase, utilizing either Hi-Nicalo(TM) fibers or the stiffer Sylramic fibers. The double-edge notched tensile test approach was used for a wide range of notch sizes and specimen widths. Both composite systems exhibited mild notch sensitivity similar to other CMC systems. Acoustic emission, detected during the tensile tests, indicated that matrix cracking occurred around notches at net-section stresses below the stress where matrix cracking first occurs in unnotched specimens. However, thermoelastic stress analysis did not show any measurable stress relief around notches after the specimens were preloaded.
This project uses the integral transform technique to model the problem of nanotube behavior as an axially symmetric system of shells. Assuming that the nanotube behavior can be described by the equations of elasticity, we seek a stress function x which satisfies the biharmonic equation: del(exp 4) chi = [partial deriv(r(exp 2)) + partial deriv(r) + partial deriv(z(exp 2))] chi = 0. The method of integral transformations is used to transform the differential equation. The symmetry with respect to the z-axis indicates that we only need to consider the sine transform of the stress function: X(bar)(r,zeta) = integral(from 0 to infinity) chi(r,z)sin(zeta,z) dz.
Potential composite applications in aerospace and transportation application systems have different thickness requirements. For example, space applications such as nozzle ramps or heat exchangers use very thin (less than 1 mm) structures whereas turbine blades need very thick parts greater than or equal to cm). There has been little investigation into the effect of thickness on stress-strain behavior or elevated temperature tensile properties controlled by oxidation. In this study, composites consisting of woven Hi-NicalonTM fibers, a carbon interphase, and CVI Sic matrix were fabricated with different numbers of plies to provide variable thickness. The composites ranged from a single ply (approximately 0.4 mm) to thirty-six plies (approximately 1 cm). Tensile tests were performed at room temperature with acoustic emission used to monitor matrix crack behavior. Elevated temperature tensile stress-rupture tests were performed in air. Considerably different room and elevated temperature tensile behavior was observed that will be discussed with respect to the effect of thickness on matrix crack formation, matrix crack growth and oxidation diffusion kinetics.
Due to lack of "real" lunar soil or even lunar simulant, it is difficult to characterize the interaction between lunar soil (or simulant) with different surfaces that are involved in excavation and processing machinery. One unique feature possessed by lunar soil is the agglutinates produced by repeated high-speed micrometeoroid impacts and subsequent pulverization[l and 2]. The large particles are impacted by micrometeoroids [Fig.l] and pulverized to produce finer particles. This process continues until there are no more "large" particles left on the surface of the moon. Due to high impact speed, the impact melting process fuses fines to make agglutinates such as shown in Fig. 2. We will present a series of simulation results and movies will be shown to indicate brittle behavior of each individual agglutinate and also similar compressibility charts shown by Carrier et al. [3]. Fig. 3 shows our preliminary result of the simulated oedometer tests.
High-temperature shape memory alloys in the NiTiPd system are being investigated as lower cost alternatives to NiTiPt alloys for use in compact solid-state actuators for the aerospace, automotive, and power generation industries. A range of ternary NiTiPd alloys containing 15 to 46 at.% Pd has been processed and actuator mimicking tests (thermal cycling under load) were used to measure transformation temperatures, work behavior, and dimensional stability. With increasing Pd content, the work output of the material decreased, while the amount of permanent strain resulting from each load-biased thermal cycle increased. Monotonic isothermal tension testing of the high-temperature austenite and low temperature martensite phases was used to partially explain these behaviors, where a mismatch in yield strength between the austenite and martensite phases was observed at high Pd levels. Moreover, to further understand the source of the permanent strain at lower Pd levels, strain recovery tests were conducted to determine the onset of plastic deformation in the martensite phase. Consequently, the work behavior and dimensional stability during thermal cycling under load of the various NiTiPd alloys is discussed in relation to the deformation behavior of the materials as revealed by the strain recovery and monotonic tension tests.
No abstract available
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Unreinforced woven fabrics are widely employed in various high-performance applications, including parachute deployment systems, airbags, and ballistic armor. The analysis of such materials is inherently complex due to the multiscale structure of these materials, and the dependence of macroscale behavior on changes that occur at lower scales. Previously, NASA’s Multiscale Analysis Tool (NASMAT) showed its capability in predicting unreinforced fabric behavior at the macroscale by capturing finite rotations that occur at the mesoscale. Though effective, the tool can face high computational cost for large, complex problems, motivating the need for the development of a surrogate model that can capture the same behavior. A recurrent neural network (RNN) was developed and trained on virtual NASMAT data to mimic the physics-based solutions while improving the computational runtime. The architecture of the RNN to best simulate the fabric behavior was carefully crafted based on heuristic knowledge of predicting physics-based temporal data, manual hyperparameter case studies, and Hyperband optimization.. The resultant model was able to predict a variety of stress-strain curves for fabrics with different mesoscale geometries, and was further validated by comparing to experimental data for the K706 style Kevlar plain-weave fabric, demonstrating the ability of the model to effectively capture the geometric changes in the fabric without explicitly calculating them, as is done in NASMAT. Furthermore, the tool showed its ability to improve on the runtime by a factor of 10 for fabric solutions compared to the multiscale tool, which would further enable the simulation of complex loading scenarios on unreinforced fabrics.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The dissolution of atmospheric gases into parts additively manufactured by directed energy deposition (DED) has long been of concern, and stock shielding solutions have usually proven inadequate at fully removing atmospheric gases from weld beads. The objective of this work was to design a new supplementary argon gas shroud for a specific DED printer and evaluate its effect on microstructure and macroscopic properties of SS316L and the potential for printing more reactive metals such as Ti-6Al-4V. This was investigated by printing four SS316L sample blocks, two with and two without the shroud, each printed in two different orientations. These samples were subsequently evaluated with inert gas fusion (IGF), SEM/EDS imaging, and tensile tests. The shroud reduced oxygen content by 0.019-0.031%, and SEM imaging revealed fewer oxide inclusions. A more dramatic reduction of 0.13% oxygen and 0.171% nitrogen was observed by the inert gas fusion of Ti-6Al-4V samples. Overall, the results indicated the shroud was successful at reducing atmospheric gas uptake within the print region and may enable the printing of reactive metal powders in DED systems.
Treatment of Nextel (TM) 312 in a reactive environment has been used as a low cost approach to the formation of BN on the fiber surface. Although the BN enriched surface region is extremely thin (less than 40 run), it is effective in providing debonding and composite behavior. Variation in mechanical behavior of Nextel (TM) 312/BN/Blackglas (TM) composites has been noted among panels fabricated with AF-10 cloth treated in different nitridation runs, Understanding this variation became the rationale for undertaking a detailed characterization of the nitrided fiber using field emission scanning electron microscopy, low voltage energy dispersive x-ray and Auger electron spectroscopy. Chemical composition and surface morphology are discussed in relation to observed mechanical behavior of NeXtel (TM) 312/Blackglas (TM) composites tested in bending.
Nuclear radiation effect on structural and mechanical relaxation behavior of polytetrafluorethylene at audio frequencies
The overarching goal of this project is to understand the phase stability and mechanical behavior of non-stoichiometric multi-principal element alloy (MPEA) materials. In order to identify suitable alloys, we plan to use a combinatorial thin film screening approach, in collaboration with scientists at Lawrence Berkeley National Laboratory who are performing computational work as well as complementary experimental work. Specific tasks within the scope of this project include the fabrication, using thin film deposition from six sputtering targets, of combinatorial samples with multi-dimensional gradients in composition and microstructure. These samples are studied to screen MPEA systems for promising candidate alloys with specific composition(s), based on characterization of composition, structure and mechanical behavior across the thin film. We want to produce single-phase MPEAs with chemical homogeneity in a given thin film region, simple grain structures, and no intermetallic phases present. Gradient films facilitate first-pass screening for desirable characteristics and inform the next stage of work that involves fabrication of bulk MPEA specimens for (tensile) mechanical testing and characterization. To make the bulk alloys, metal (elemental) pieces are melted to form MPEAs, followed by heat treatment to homogenize the composition and microstructure. A subset of alloys is also cast, using vacuum arc melting, to yield larger samples (diameter ~1 cm and length ~5-10 cm) and these allow us to assess viability of scale-up for the alloys in structural applications. Further processing plans include rolling and heat treatment to recrystallize selected bulk MPEAs and grow grains to different extents, in order to investigate size effects in the mechanical behavior of MPEAs. Microspecimen testing will be performed (primarily in tension) to assess the mechanical behavior over a range of temperatures. The deformation microstructure of mechanically tested alloys will be characterized using transmission electron microscopy (TEM) to provide a scientific basis for understanding the structure-property relationships in MPEA mechanical behavior.