SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The low complexity, low size, weight and power Mid-Wavelength Infra-Red optical communications transceiver concept presented, realized and tested in the laboratory environment. Resilience to atmospheric impairments analyzed with simulated turbulence. Performance compared to typical telecom based Short Wavelength Infra-Red transceiver.
As the number of spacecraft in simultaneous operation continues to grow, there is an increased dependency on ground-based navigation support. The current baseline system for deep space navigation utilizes Earth-based radiometric tracking, requiring long-duration observations to perform orbit determination and generate a state update. The age, complexity, and high utilization of the ground assets pose a risk to spacecraft navigation performance. In order to perform complex operations at large distances from Earth, such as extraterrestrial landing and proximity operations, autonomous systems are required. With increasingly complex mission operations, the need for frequent and Earth-independent navigation capabilities is further reinforced. The Multi-spacecraft Autonomous Positioning System (MAPS) takes advantage of the growing interspacecraft communication network and infrastructure to allow for Earth-autonomous state measurements to enable network-based space navigation. A notional concept of operations is given in figure 1. This network is already being implemented and routinely used in Martian communications through the use of the Mars Reconnaissance Orbiter and Mars Odyssey spacecraft as relays for surface assets. The growth of this communications architecture is continued through MAVEN, and future potential commercial Mars telecom orbiters. This growing network provides an initial Marslocal capability for inter-spacecraft communication and navigation. These navigation updates are enabled by cross-communication between assets in the network, coupled with onboard navigation estimation routines to integrate packet travel time to generate ranging measurements. Inter-spacecraft communication allows for frequent state broadcasts and time updates from trusted references. The architecture is a software-based solution, enabling its implementation on a wide variety of current assets, with the operational constraints and measurement accuracy determined by onboard systems.
The NASA Innovative Advanced Concepts (NIAC) program has been funding work at KSC (Kennedy Space Center) on a new coating that should allow cryogenic commodities to be stored in deep space. Recently a mid-term review of this work was given. I am requesting that this presentation be cleared for release so that the material can be presented publicly at an upcoming FISO (Future in Space) telecom.
NASA Goddard Space Flight Center is developing a master oscillator power amplifier (MOPA) laser transmitter for the ESA-led Laser Interferometer Space Antenna (LISA) mission. Taking advantage of our space laser experience and the emerging telecom laser technology, we are developing a full laser system for the LISA mission. Our research effort has included both master oscillator (MO) and power amplifier (PA) developments, and their environmental testing and reliability for space flight. Our current baseline for the MO is a low-mass, compact micro NPRO (m-NPRO) laser. The amplifier uses a robust mechanical design based on fiber components. We have performed laser system noise tests by amplitude- and frequency-stabilizing the PA output. We will describe our progress and plans to demonstrate a TRL 6 laser system, which is an essential step toward qualifying lasers for space applications, by 2021.
NASA Goddard Space Flight Center is developing a master oscillator power amplifier (MOPA) laser transmitter for the ESA-led Laser Interferometer Space Antenna (LISA) mission. Taking advantage of our space laser experience and the emerging telecom laser technology, we are developing a full laser system for the LISA mission. Our research effort has included both master oscillator (MO) and power amplifier (PA) developments, and their environmental testing and reliability for space flight. Our current baseline for the MO is a low-mass, compact micro non-planar ring oscillator (m- NPRO) laser. The amplifier uses a robust mechanical design based on fiber components. We have performed laser system noise tests by amplitude- and frequency-stabilizing the PA output. We will describe our progress and plans to demonstrate a TRL 6 laser system, which is an essential step toward qualifying lasers for space applications, by 2021.
We proposed to develop a new landing approach that significantly reduces development time and obviates the most complicated, most expensive, and highest-risk phase of a landing mission. The concept is a blanket- or carpet-like two-dimensional (2D) lander (~1-m × 1-m surface area and <1-cm thick) with a low mass/drag ratio, which allows the lander to efficiently shed its approach velocity and provide a more robust structure for landing integrity. The form factor of these landers allows dozens to be stacked on a single spacecraft for transport and distributed en masse to the surface. Lander surfaces will be populated on both sides by surface-mount, low-profile sensors and instruments, surface-mount telecom, solar cells, batteries, processors, and memory. Landers will also incorporate thin flexible electronics, made possible in part by printable electronics technology. The mass and size of these highly capable technologies further reduces the required stiffness and mass of the lander structures to the point that compliant, lightweight, robust landers capable of passive landings are possible. This capability avoids the costly, complex use of rockets, radar, and associated structure and control systems. This approach is expected to provide an unprecedented science payload mass to spacecraft mass ratio of approximately 80% (estimated based on current knowledge). This compared to ~1% for Pathfinder, ~17% for MER, and 22% for MSL rovers. Clearly, one difference is rovers vs. a lower capability lander. An outcome of the Phase I study is a clear roadmap for near-term demonstration and long-term technology development.
Interplanetary CubeSats could enable small, low-cost missions beyond low Earth orbit. This class is defined by mass < ~ 10 kg, cost < $30 M, and durations up to 5 years. Over the coming decade, a stretch of each of six distinct technology areas, creating one overarching architecture, could enable comparatively low-cost Solar System exploration missions with capabilities far beyond those demonstrated in small satellites to date. The six technology areas are: (1) CubeSat electronics and subsystems extended to operate in the interplanetary environment, especially radiation and duration of operation; (2) Optical telecommunications to enable very small, low-power uplink/downlink over interplanetary distances; (3) Solar sail propulsion to enable high !V maneuvering using no propellant; (4) Navigation of the Interplanetary Superhighway to enable multiple destinations over reasonable mission durations using achievable !V; (5) Small, highly capable instrumentation enabling acquisition of high-quality scientific and exploration information; and (6) Onboard storage and processing of raw instrument data and navigation information to enable maximum utility of uplink and downlink telecom capacity, and minimal operations staffing. The NASA Innovative Advanced Concepts (NIAC) program in 2011 selected Interplanetary CubeSats for further investigation, some results of which are reported here for Phase 1.
We report on the development and demonstration of a compact 2-micron semiconductor seed laser for CO2 lidar instruments. Our monolithic high-power fiber-pigtailed semiconductor seed laser will greatly enhance the operability and applicability of IPDA (Integrated Path Differential Absorption) lidar systems for high spatial and temporal resolution CO2 airborne measurements as well as future Earth-orbiting CO2 measurement missions. The compact semiconductor transmitter has a suitably narrow linewidth (less than 100 kilohertz) and enables flexible tuning (greater than 150 gigahertz) over several CO2 absorption lines in the 2.05-micron band.The frequency agility and multi-format modulation capability of the proposed technology, its small size and compatibility with standard DFB (Distributed FeedBack) lasers at the telecom band paves the way for adoption of the attractive 2.05-micron band for CO2 profiling and measurements.
Radio communications between the Juno spacecraft, in orbit around Jupiter, and the Earth-based observing stations of NASA’s Deep Space Network enable measurements of the Doppler shift induced on the radio signals by Juno’s motion in the Jovian environment. This measurement of the Doppler shift improves the knowledge of Jupiter’s gravitational field. As a radio science instrument, Juno’s gravity science instrument utilizes a ground component at the Deep Space Network’s DSS-25 antenna, equipped with simultaneous dual X- and Ka-band transmitters and receivers, and a spacecraft component, which includes X- and Ka-band transponders to relay the transmitted signal back to Earth. Originally planned to be in 14-day orbits around Jupiter, a risk identified in the propulsion system led to the decision to stay in the 53-day orbit period. Rapid turnaround of observation planning led to successful near-term perijove passes. Although maintaining a 53-day orbit period provides a scientific benefit to the gravity science investigation, the longer orbit period further increases the large dynamic range in Doppler shift and pointing angles induced by the geometry of each perijove. Between entering orbit at Jupiter on July 5, 2016 and September 2017, the Juno spacecraft has executed eight closest approach periods every 53 days where science data was collected. The first five perijove passes were conducted in different telecom configurations, each presenting unique challenges in data collection and processing. Perijoves PJ-01, PJ-02, PJ-03, and PJ-06 utilized the high-gain antenna and various configurations of the X- and Ka-bands. Perijoves PJ-04 and PJ-05 utilized the medium-gain antenna at X-band only while the spacecraft was off-Earth point. Additional perijoves are planned every 53-days, with an additional five by March 2018. Lessons learned from operating and collecting data at each perijove are documented and will be utilized in future perijoves. Analysis of the first two gravity science perijoves has improved the precision of Jupiter’s gravity field by a factor of five, providing crucial constraints on the interior structure of Jupiter.
NASA's Mars 2020 rover will carry a wideband (150 megahertz to 1200 megahertz) ground penetrating radar—RIMFAX (Radar Imager for Mars’ subsurFace eXperiment ), contributed by FFI (Forsvarets forskningsinstitutt) of Norway—to survey the subsurface geology of Mars. RIMFAX will take radar soundings while the rover drives across the Martian terrain, which presents possible compatibility issues between rover and radar operations. In order to study this risk, a prototype RIMFAX antenna was attached to the flight-analogous rover Vehicle System Test Bed (VSTB) in a mechanically representative location. The prototype antenna collected spectral and time-domain data across a variety of driving operations in order to assess the radar sensitivity to rover-generated noise. Conversely, the prototype antenna was driven while an engineering-model UHF (Ultra High Frequency) antenna used for rover telecom measured received in-band power to ensure that the rover hardware was not at risk of damage. Evaluation of the data by the instrument science team showed that while rover noise was apparent to the receiver, data post-processing would yield greater than 40 decibels margin to the science requirements. Similarly, power levels received by the UHF antenna were well below damage thresholds.
This paper provides the status of the Mars Laser Communication Demonstration Project, a joint project between NASA's Goddard Space Flight Center (GSFC), the California Institute of Technology Jet Propulsion Laboratory (JPL), and the Massachusetts Institute of Tecnology Lincoln Laboratory (MIT/LL). It reviews the current ideas/designs for the flight and ground segments, the critical technologies required, adn the concept of operations. The laser communication (lasercom) flight terminal will be flown on the Mars Telecom Orbiter (MTO) to be launched by NASA in 2009, and will demonstrate a technology which has the potential of vastly improving NASA's ability to communicate throughout the solar system.
This paper provides an overview of the Mars Laser Communications Demonstration Project, a joint project between NASA’s Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory, California Institute of Technology (JPL), and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL). It reviews the strawman designs for the flight and ground segments, the critical technologies required, and the concept of operations. It reports preliminary conclusions from the Mars Lasercom Study conducted at MIT/LL and on additional work done at JPL and GSFC. The lasercom flight terminal will be flown on the Mars Telecom Orbiter (MTO) to be launched by NASA in 2009, and will demonstrate a technology which has the potential of vastly improving NASA’s ability to communicate throughout the solar system
The deployable array antenna using an inflatable or thin-membrane structure has been identified as one of the enabling technologies to achieve low-mass, high packaging efficiency, low cost, and reliable deployment for future NASNJPL spacebome high-gain and large aperture antennas. Array antennas, when compared to parabolic reflectors, although suffering from limited bandwidth performance, offer wide-angle beam scanning capability and a more reliable flat “natural” aperture. To demonstrate the feasibility and capability of this low-mass array technology, three antenna concepts using inflatable and thin-membrane structures were initiated in 1997 at JPL and several breadboard units have been successfully developed. These three concepts are (1) the inflatable phased array, (2) the inflatable reflectarray, and (3) frame-supported thin membrane array antenna. All three concepts utilize the printed microstrip antenna technology. Although all three concepts will be briefly presented, this paper will discuss in more detail of the recent development of the second concept. The first concept of inflatable phased arrays that have been constructed are 3 to 5-meter size L-band dual-polarized synthetic aperture radar (SAR) arrays for Earth remote sensing application. They all consist of a rectangular configuration with inflatable cylindrical tubes that support and tension a multi-layer thin-membrane radiating aperture with microstrip patches and microstrip power divider lines. For the second concept, an inflatable reflectarray was developed for future deep-space telecom applications. It is a 3m Ka-band inflatable reflectarray (1.8 kg/m2). This reflectarray uses inflated torus tubes to support and tension a flat-membrane reflectarray surface. The reflectarray surface emulates a curved parabolic reflecting surface. However, because of its flat surface being a “natural surface”, it is much easier to achieve and more reliable to maintain the required surface tolerance than that of a curved parabola during long space flight. For the third concept, an L-band dual polarized SAR array with a 5m x 3m aperture and 2.5 kg/m2 of mass has recently been demonstrated. It consists of seven foldable panels each having a rectangular frame that supports a two-layer thinmembrane microstrip subarray aperture. Each frame is made of light-weight graphite composite material. The chief advantage of this deployable “frame” concept is that each frame is able to rigidly support an appropriate number of T/R modules and phase shifters to achieve the desired power distribution and beam scanning. Several technology challenges, such as the development of rigidizable inflatable tubes, a controlled deployment mechanism, thin-membrane thermal effects, a low-mass inflation system, membrane mounted T/R modules, means to counter surface tolerance issues, etc. are being investigated and will be discussed in the presentation. With foreseeable success in the development of these challenging areas, the inflatable/thin-membrane array antennas could be mature enough in a few years for actual space flight.
A system for global inventory control of electronically tagged military hardware is achievable using a constellation of low earth orbit (LEO) satellites. Investigated are two proposed commercial LEO systems, both capable of providing global coverage but with dramatically different telecom capacities. This study is to verify the feasibility and performance of direct Tag-satellite communication.
In January 2017, Psyche was one of two mission concepts selected by NASA for flight as part of the 14th Discovery mission competition. The project has been staffing up and maturing the spacecraft, instrument and mission system baseline designs on the path towards a 2022 launch. During much of 2018, the Project has been executing the lifecycle stage called Phase B, “Preliminary Design and Technology Completion,” one key element of which is the development and management of requirements at various levels. In the case of the Psyche project, this process has been particularly unique for several reasons. The project utilizes a Solar Electric Propulsion (SEP) Chassis from Space Systems Loral (SSL), a high volume manufacturer of commercial geostationary (GEO) telecom spacecraft based on the 1300 satellite bus. While SSL has an extensive, well-vetted set of requirements based on their very successful Earth-orbiting product line, translating that heritage to a deep space science mission required special care. In addition to the differences associated with the deep space environment and longer communication times, new interfaces had to be incorporated. While a substantial portion of the Flight System consists of the SEP Chassis, there were several new interfaces within various subsystems between SSL components and those provided by JPL and other contractors. Managing these interfaces through requirements at a relatively higher level than normally seen on internal or external builds proved challenging. Finally, the Psyche spacecraft plans to host the flight terminal of the Deep Space Optical Communications (DSOC) technology demonstration, which is itself a separate project with its own requirements that must be flowed down and managed. This paper will present an overview of the requirement development and management process for the Psyche project. It will discuss in detail the various challenges summarized above, the methods and decisions chosen to address them, and evaluate their overall effectiveness at this stage in the project.
The Universal Space Transponder (UST) is a next generation transponder developed at the Jet Propulsion Laboratory to meet a large variety of telecom, navigation, and radio science needs for future deep-space and near-Earth missions. This paper details the UST software defined radio design and describes how the combination of a modular hardware architecture and in-flight reprogrammability enables a new level of flexibility and expandability for a space transponder. The UST uses common power and digital processing assemblies that can be integrated with a variety of RF modules and is capable of simultaneous, multiband operations with data rates up to 37.5 Mbps RX and 300 Mbps TX. This allows a single radio to support all the direct-to-Earth and relay communication requirements for even complex mission scenarios, reducing the total cost, mass, and power. The discussion includes a description of the current UST engineering models that have been built and tested, as well as details about the next generation capabilities supported by UST, including advanced link coding and modulation, radiometric techniques, and in-radio protocol handling. Details are also presented on RF modules and digital processing in development for radio science and astronomy purposes, including a bistatic radar receiver and broadband planetary emissions receiver. These will demonstrate the ability to integrate low-cost science instruments into the UST architecture, further expanding the versatility of the UST.
Operations engineering teams interact with complex data systems to make technical decisions that ensure the operational efficacy of their missions. To support these decision-making tasks, which may require elastic prioritization of goals dependent on changing conditions, custom analytics tools are often developed. We were asked to develop such a tool by a team at the NASA Jet Propulsion Laboratory, where rover telecom operators make decisions based on models predicting how much data rovers can transfer from the surface of Mars. Through research, design, implementation, and informal evaluation of our new tool, we developed principles to inform the design of visual analytics systems in operations contexts. We offer these principles as a step towards understanding the complex task of designing these systems. The principles we present are applicable to designers and developers tasked with building analytics systems in domains that face complex operations challenges such as scheduling, routing, and logistics.
This paper provides a description and analyses of the high-rate Ka-band telecom system for the upcoming NISAR (NASA-ISRO Synthetic Aperture Radar) mission. NISAR is a collaborative Earth-Science mission between National Aeronautics and Space Administration (NASA) and Indian Space Research Organization (ISRO), which features an L-band SAR instrument and an S-band SAR instrument. The simultaneous dual-frequency radar system at peak rates will produce data at gigabit-per-second speeds, which drives the data-volume requirements. The key driving requirement for the payload communication subsystem is to provide a minimum of 26 Terabits per day of radar science data to the ground. The high-rate transmitter on the flight system is a software-defined radio developed at the Jet Propulsion Laboratory (JPL), based on the Universal Space Transponder platform, providing an offset quadrature phase shift key modulated waveform with Low-Density Parity-Check encoding of the data transfer frames. Two transmitters used in a dual-polarization configuration with each transmitter providing two giga-symbols per second (Gsps) of coded data provides an aggregate rate of four Gsps. In this system, only one watt of signal power is necessary on each polarization to overcome propagation losses and achieve a successful RF link. Several Near Earth Network (NEN) ground station sites (Alaska in the United States, Svalbard in Norway, and Punta Arenas in Chile) are baselined for the space-to-Earth communications link. Each ground station will also feature multiple upgrades to support NISAR’s transmission starting with new Ka-band antennas, wideband downconverters and high-rate receivers. In addition, a baseband data processor called Data Acquisition Processor and Handling Network Environment (DAPHNE), newly developed by the NEN, provides data storage and connectivity to backhaul networks. With NISAR’s large quantities of data (over 3.5 Petabytes over the mission), the processing of science data will be primarily performed on a cloud system to reduce the overall cost to the mission. The system described herein will be the first operational use of Gsps-class downlink rates on an Earth-Science mission.