SEARCH · Search NASA

Results for “Instrument Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

All sources NASA NTRS DOE OSTI

NASA NTRS1997

Sample Diluter for Detecting Hypergolic Propellants and Other Toxic or Hazardous Gases

Hardware was developed to dilute vapor samples of purged hypergolic propellants (with air) into the range of existing instruments for detection of such toxic vapors. Since these detectors are normally used to monitor at the threshold limit value (TLV), most do not have quantitative capability at percent levels which relate to lower explosion limit (LEL) and fire hazards. For example, the upper limits of Energetic Sciences (ESI) 6000 series detectors used at KSC are 200 parts per million (ppm) for monomethyl hydrazine (MMH) and 500 ppm for nitrogen dioxide (NO2) arising from decomposition of nitrogen tetroxide (N2O4). Orbiter Processing Facility (OPF) personnel servicing Shuttle thrusters need to measure up to 250 ppm MMH and 7500 ppm NO2 with portable, intrinsically safe instruments. Our objective was to quickly fabricate a sample diluter out of existing materials as a temporary measure while other parallel efforts were conducted to provide a commercial or in-house-developed instrument to detect high propellant levels. A 3 to 1 diluter would bring 500 ppm MMH into the range of the existing fuel ESI, and a 30 to 1 diluter would do the same for NO2. In this way, familiar equipment already available would be used, resulting in minimal paperwork, safety, and training impacts and low cost. An MMH vapor sample-diluter was constructed from a 1/4-inch Kynar tee, along with specially designed lengths of sample and dilution tubing. The sample line was 3 feet of Bev-A-Line 4, 1/4 inch tube leading to the straight run of the tee. The side run of the tee had a 17-inch length of Bev-A-Line 4, 1/4-inch tube, for nominal 3 to 1 dilution. A gas sample bag was prepared and assayed at 113 ppm MMH, and diluted vapor sarnples were assayed at 39.5 ppm, or a measured dilution of 2.9 to 1. For NO2, a 316 stainless steel (SS) 1/8-inch tee with 49.5 inches of coiled, 1/8-inch outside diameter (OD) 316 SS tubing was used as the sarnpling end of the dilution system. The side run of the tee was open. The measured dilution ratio, based on the input value of 6,480 ppm NO2 and the average output value of 233 ppm, was 28 to 1. Thus, sample-diluters were successful in diluting concentrated hypergolic propellant vapors, both MMH and N2O4, into the ranges of existing TLV detectors.

Barile, R. G.↗

NASA NTRS2015

The Suomi National Polar-Orbiting Partnership (SNPP): Continuing NASA Research and Applications

The Suomi National Polar-orbiting Partnership (SNPP) satellite was successfully launched into a polar orbit on October 28, 2011 carrying 5 remote sensing instruments designed to provide data to improve weather forecasts and to increase understanding of long-term climate change. SNPP provides operational continuity of satellite-based observations for NOAA's Polar-orbiting Operational Environmental Satellites (POES) and continues the long-term record of climate quality observations established by NASA's Earth Observing System (EOS) satellites. In the 2003 to 2011 pre-launch timeframe, NASA's SNPP Science Team assessed the adequacy of the operational Raw Data Records (RDRs), Sensor Data Records (SDRs), and Environmental Data Records (EDRs) from the SNPP instruments for use in NASA Earth Science research, examined the operational algorithms used to produce those data records, and proposed a path forward for the production of climate quality products from SNPP. In order to perform these tasks, a distributed data system, the NASA Science Data Segment (SDS), ingested RDRs, SDRs, and EDRs from the NOAA Archive and Distribution and Interface Data Processing Segments, ADS and IDPS, respectively. The SDS also obtained operational algorithms for evaluation purposes from the NOAA Government Resource for Algorithm Verification, Independent Testing and Evaluation (GRAVITE). Within the NASA SDS, five Product Evaluation and Test Elements (PEATEs) received, ingested, and stored data and performed NASA's data processing, evaluation, and analysis activities. The distributed nature of this data distribution system was established by physically housing each PEATE within one of five Climate Analysis Research Systems (CARS) located at either at a NASA or a university institution. The CARS were organized around 5 key EDRs directly in support of the following NASA Earth Science focus areas: atmospheric sounding, ocean, land, ozone, and atmospheric composition products. The PEATES provided the system level interface with members of the NASA SNPP Science Team and other science investigators within each CARS. A sixth Earth Radiation Budget CARS was established at NASA Langley Research Center (NASA LaRC) to support instrument performance, data evaluation, and analysis for the SNPP Clouds and the Earth's Radiant Budget Energy System (CERES) instrument. Following the 2011 launch of SNPP, spacecraft commissioning, and instrument activation, the NASA SNPP Science Team evaluated the operational RDRs, SDRs, and EDRs produced by the NOAA ADS and IDPS. A key part in that evaluation was the NASA Science Team's independent processing of operational RDRs and SDRs to EDRs using the latest NASA science algorithms. The NASA science evaluation was completed in the December 2012 to April 2014 timeframe with the release of a series of NASA Science Team Discipline Reports. In summary, these reports indicated that the RDRs produced by the SNPP instruments were of sufficiently high quality to be used to create data products suitable for NASA Earth System science and applications. However, the quality of the SDRs and EDRs were found to vary greatly when considering suitability for NASA science. The need for improvements in operational algorithms, adoption of different algorithmic approaches, greater monitoring of on-orbit instrument calibration, greater attention to data product validation, and data reprocessing were prominent findings in the reports. In response to these findings, NASA, in late 2013, directed the NASA SNPP Science Team to use SNPP instrument data to develop data products of sufficiently high quality to enable the continuation of EOS time series data records and to develop innovative, practical applications of SNPP data. This direction necessitated a transition of the SDS data system from its pre-launch assessment mode to one of full data processing and production. To do this, the PEATES, which served as NASA's data product testing environment during the prelaunch and early on-orbit periods, were transitioned to Science Investigator-led Processing Systems (SIPS). The distributed data architecture was maintained in this new system by locating the SIPS at the same institutions at which the CARS and PEATES were located. The SIPS acquire raw SNPP instrument Level 0 (i.e. RDR) data over the full SNPP mission from the NOAA ADS and IDPS through the NASA SDS Data Distribution and Depository Element (SD3E). The SIPS process those data into NASA Level 1, Level 2, and global, gridded Level 3 standard products using peer-reviewed algorithms provided by members of the NASA Science Team. The SIPS work with the NASA SNPP Science Team in obtaining enhanced, refined, or alternate real-time algorithms to support the capabilities of the Direct Readout Laboratory (DRL). All data products, algorithm source codes, coefficients, and auxiliary data used in product generation are archived in an assigned NASA Distributed Active Archive Center (DAAC).

remote sensing↗

NASA NTRS1992

A Backscatter Moessbauer Spectrometer (BaMS) for use on Mars

The use of Moessbauer spectroscopy for in situ analysis on the surface of Mars was proposed and the design and implementation of a backscatter Moessbauer spectrometer (BaMS) instrument suitable for planetary missions to the surfaces of Mars (MESUR), the Moon (Artemis and lunar outpost), asteroids, or other solid solar system objects is discussed. The BaMS instrument is designed to be capable of analysis of a sample for the mineralogy of its iron-bearing phases without any sample preparation. A requirement of lander missions to Mars is instrumentation for in situ mineralogical analyses. Such analyses provide data needed for primary characterization as to the type of surface materials present and by inference the processes that formed and subsequently modified them. For purposes of providing diagnostic information about naturally occurring materials, the element iron is particularly important because it is abundant and multivalent (primarily 0, +2, and +3 oxidation states). Knowledge of the oxidation state of iron and its distribution among iron-bearing mineralogies tightly constrains the types of materials present. The pivotal role of iron was already recognized in 1978 by COMPLEX, who recommended development of flight instruments that would identify mineralogy and the oxidation state of iron in planetary surface materials. The near-term U.S. strategy for the exploration of Mars is the MESUR (Mars Environmental SURvey) program, which entails emplacement of a network of small, long-lived surface landers. For the Moon, BaMS was recommended as part of a three-instrument landed payload for the Artemis missions, targeted for 1997. BaMS would prospect for ilmenite, an oxygen resource material, and provide data to assess the maturity of lunar soil. Because instrumental characteristics are low mass, low volume, and low power consumption, BaMS is suitable for implementation on even small landers and rovers, as are being envisioned in MESUR and Artemis concepts. In addition to providing highly diagnostic data, a BaMS analyzer is inherently simple and, as is highly desirable for remote operation, no sample preparation is required.

Agresti, D. G.↗

NASA NTRS2010

Distributed Disdrometer and Rain Gauge Measurement Infrastructure Developed for GPM Ground Validation

Global Precipitation Mission (GPM)retrieval algorithm validation requires datasets characterizing the 4-D structure, variability, and correlation properties of hydrometeor particle size distributions (PSD) and accumulations over satellite fields of view (FOV;<10 km). Collection of this data provides a means to assess retrieval errors related to beam filling and algorithm PSD assumptions. Hence, GPM Ground Validation is developing a deployable network of precipitation gauges and disdrometers to provide fine-scale measurements of PSD and precipitation accumulation variability. These observations will be combined with dual-frequency, polarimetric, and profiling radar data in a bootstrapping fashion to extend validated PSD measurements to a large coverage domain. Accordingly, a total of 24 Parsivel disdrometers(PD), 5 3rd-generation 2D Video Disdrometers (2DVD), 70 tipping bucket rain gauges (TBRG),9 weighing gauges, 7 Hot-Plate precipitation sensors (HP), and 3 Micro Rain Radars (MRR) have been procured. In liquid precipitation the suite of TBRG, PD and 2DVD instruments will quantify a broad spectrum of rain rate and PSD variability at sub-kilometer scales. In the envisioned network configuration 5 2DVDs will act as reference points for 16 collocated PD and TBRG measurements. We find that PD measurements provide similar measures of the rain PSD as observed with collocated 2DVDs (e.g., D0, Nw) for rain rates less than 15 mm/hr. For heavier rain rates we will rely on 2DVDs for PSD information. For snowfall we will combine point-redundant observations of SWER distributed over three or more locations within a FOV. Each location will contain at least one fenced weighing gauge, one HP, two PDs, and a 2DVD. MRRs will also be located at each site to extend the measurement to the column. By collecting SWER measurements using different instrument types that employ different measurement techniques our objective is to separate measurement uncertainty from natural variability in SWER and PSD. As demonstrated using C3VP polarimetric radar, gauge, and 2DVD/PD datasets these measurements can be combined to bootstrap an area wide SWER estimate via constrained modification of density-diameter and radar reflectivity-snowfall relationships. These data will be combined with snowpack, airborne microphysics, radar, radiometer, and tropospheric sounding data to refine GPM snowfall retrievals. The gauge and disdrometer instruments are being developed to operate autonomously when necessary using solar power and wireless communications. These systems will be deployed in numerous field campaigns through 2016. Planned deployment of these systems include field campaigns in Finland (2010), Oklahoma (2011), Canada (2012) and North Carolina (2013). GPM will also deploy 20 pairs of TBRGs within a 25 km2 region along the Virginia coast under NASA NPOL radar coverage in order to quantify errors in point-area rainfall measurements.

Petersen, Walter A.↗

NASA NTRSDate not supplied

Automated Reconfigurable Mission Adaptive Digital Assembly Systems (ARMADAS): Robotically Assembled Sustainable Lunar Infrastructure

Introduction: The Automated Reconfigurable Mission Adaptive Digital Assembly Systems (ARMADAS) project at NASA Ames Research Center is developing autonomous infrastructure, instrumentation, and spacecraft assembly and manufacturing capabilities for next generation exploration and science missions, with a goal to change the cost scaling of these missions relative to mission size and duration. Using a building-block approach with a 'kit of parts' composed of ultra-light, high-performance mechanical metamaterials, simplified robots leverage the period environment to achieve high levels of autonomy and reliability for in-space and surface assembly of large-scale apertures, solar-arrays, towers, habitats, and other infrastructure. Robots and structure break down into a compact form factor for launch. By leveraging economies of scale and achieving high-packing ratios, ARMADAS technology can revolutionize possible space missions by breaking the tyranny of the launch shroud, decreasing development times, decreasing mission costs for transformative science capability, and providing a scalable and versatile space infrastructure strategy. Capabilities: To date, the ARMADAS project has demonstrated autonomous assembly of large numbers of structural modules into a meters-scale structure in an earth gravity environment. The mechanical performance is on par with conventional space structures, at a fraction of the cost. By using highly repeatable manufacturing processes (injection molding carbon fiber reinforced space-rated polymers), the structures are both cost effective and highly precise. The ARAMADAS system carefully designs parts for high-precision assembly–the simple and cost-effective robots build structures much larger and more precise than themselves. While maintaining structural efficiency, the ARMADAS system encompasses many functional module types, including for solar power, comm/power routing, etc., that will enable entire infrastructure systems to be engineered and autonomously assembled with modular parts. With well-defined interfaces, custom instrumentation modules can easily be added to fit many mission objectives. Lunar Infrastructure Vision: At the LSIC spring meeting, ARMADAS will present a vision for a general-purpose lunar construction kit capable of meeting a wide variety of lunar surface infrastructure needs (Figure 1). Investing in an ecosystem of reconfigurable, discretely repairable parts and robots enables systems than can expand their capability, reconfigure to meet emergency or unforeseen needs, self-repair and reduce spare-part needs. With a small set of parts (module types), a wide variety of infrastructure needs can be met. Footing modules will allow infrastructure construction at locations with no surface preparation. Footer, primary structure, and rail modules can create reconfigurable rail systems. These rail systems can be used to reduce cost-of-transport between frequently accessed sites, provide dust mitigation, and convey power and communications. High-performance structure modules combined with power-routing and solar modules can create tall towers for power and communication. Concepts for habitats and garages encompass a structure to support regolith cover for a pre-integrated module to an entirely ARMADAS system-based structure. This system can be leveraged by many in-situ resource utilization (ISRU) technologies to simplify processes and augment capabilities.

C. E. Gregg↗

NASA NTRS1972

Prototype ultrasonic instrument for quantitative testing

A prototype ultrasonic instrument has been designed and developed for quantitative testing. The complete delivered instrument consists of a pulser/receiver which plugs into a standard oscilloscope, an rf power amplifier, a standard decade oscillator, and a set of broadband transducers for typical use at 1, 2, 5 and 10 MHz. The system provides for its own calibration, and on the oscilloscope, presents a quantitative (digital) indication of time base and sensitivity scale factors and some measurement data.

Lynnworth, L. C.↗

NASA NTRS1989

A laser tracking dynamic robot metrology instrument

Research work over several years has resulted in the development of a laser tracking instrument capable of dynamic 3-D measurements of robot end-effector trajectories. The instrument characteristics and experiments to measure the static and dynamic performance of a robot in an industrial manufacturing environment are described. The use of this technology for space applications is examined.

Parker, G. A.↗

NASA NTRS1995

Standardization of surface contamination analysis systems

Corrosion products, oils and greases can potentially degrade material bonding properties. The Marshall Space Flight Center (MSFC) Surface Contamination Analysis Team (SCAT) utilizes a variety of analytical equipment to detect identify and quantify contamination on metallic and non-metallic substrates. Analysis techniques include FT-IR Microscopy (FT-IR), Near Infrared Optical Fiber Spectrometry (NIR), Optically Stimulated Electron Emission (OSEE), Ultraviolet Fluorescence (UVF) and Ellipsometry. To insure that consistent qualitative and quantitative information are obtained, standards are required to develop analysis techniques, to establish instrument sensitivity to potential contaminants, and to develop calibration curves. This paper describes techniques for preparing and preserving contamination standards. Calibration of surface contamination analysis systems is discussed, and methods are presented for evaluating the effects of potential contaminants on bonding properties.

Boothe, Richard E.↗

NASA NTRS1996

The Impact of Information Technology on the Design, Development, and Implementation of a Lunar Exploration Mission

From the beginning to the present expeditions to the Moon have involved a large investment of human labor. This has been true for all aspects of the process, from the initial design of the mission, whether scientific or technological, through the development of the instruments and the spacecraft, to the flight and operational phases. In addition to the time constraints that this situation imposes, there is also a significant cost associated with the large labor costs. As a result lunar expeditions have been limited to a few robotic missions and the manned Apollo program missions of the 1970s. With the rapid rise of the new information technologies, new paradigms are emerging that promise to greatly reduce both the time and cost of such missions. With the rapidly increasing capabilities of computer hardware and software systems, as well as networks and communication systems, a new balance of work is being developed between the human and the machine system. This new balance holds the promise of greatly increased exploration capability, along with dramatically reduced design, development, and operating costs. These new information technologies, utilizing knowledge-based software and very highspeed computer systems, will provide new design and development tools, scheduling mechanisms, and vehicle and system health monitoring capabilities that have hitherto been unavailable to the mission and spacecraft designer and the system operator. This paper will utilize typical lunar missions, both robotic and crewed, as a basis to describe and illustrate how these new information system technologies could be applied to all aspects such missions. In particular, new system design tradeoff tools will be described along with technologies that will allow a very much greater degree of autonomy of exploration vehicles than has heretofore been possible. In addition, new information technologies that will significantly reduce the human operational requirements will be discussed.

Gross, Anthony R.↗

NASA NTRS2002

Microphysics and Radiative Properties of Cirrus: Instrumentation and Analysis

Work under this grant has involved further development of a new aircraft instrument (the cloudscope) for real time characterization of atmospheric particulates together with field observations of such particulates, both in the form of ice and also as nuclei responsible for nucleation of both ice and water cloud particles. Part of the work involving assessment of the frequency of ice crystal shapes has been carried out in collaboration with the Meteorological Service of Canada; part of the work in a field program with the NCAR C-130. Part of the work has been interpreted in terms of laboratory simulation of ice crystal growth under a wide variety of conditions carried out under a grant from Physical Meteorology Program, National Science Foundation.

Hallett, John↗

NASA NTRSDate not supplied

Dust Ejecta RADAR Technology (DERT): A Millimeter Wave Doppler Radar to Measure Plume Surface Interaction Ejecta Velocities

A novel method to measure the velocity of ejecta generated by the impingement of rocket plumes on a lunar or planetary surface is presented. Dust Ejecta RADAR Technology (DERT), is a Millimeter Wave Doppler Radar sensor that provides a unique dataset based on direct measurements of ejecta particle velocities during plume-surface interactions, which will help inform risk assessments associated with impacts by high-speed ejecta particles. DERT has measured velocities of a pendulum (~1 m/s), a rotating strip (60 m/s), projected regolith simulant BP-1 (~250 m/s) and rifle rounds (~820 m/s). Signal-to-noise ratios of up to 60 dB with regolith simulant BP-1 have been demonstrated with a CW 94 GHz unit. Data collected from DERT will inform the development of high-fidelity computational models of plume-surface interaction effects and will help address NASA Strategic Knowledge Gaps related to characterizing entry, descent and landing effects, and the risks associated with high-speed ejecta on the lander and lunar surface assets. Recent efforts to develop DERT as a flight instrument are presented as well as the development of a Lunar Regolith Ejecta Simulator (LuRES) system to calibrate DERT.

PSI↗

DOE OSTI2017

Combustion energy frontier research center (CEFRC) final report (August 1, 2009 – July 31, 2016)

The Combustion Energy Frontier Research Center (CEFRC) was established to tackle the single overarching grand challenge of energy sustainability, energy security and global warming: to develop a “validated, predictive, multi-scale, combustion modeling capability to optimize the design and operation of evolving fuels in advanced engines for transportation applications,” as identified in the DOE report on “Basic Energy Needs for Clean and Efficient Combustion of 21st Century Transportation Fuels”. The challenge is particularly daunting since energy conversion efficiencies and exhaust emissions are governed by coupled chemical and transport processes at multiple length scales ranging from electron excitation to molecular rearrangements to nanoscale particulate formation to turbulent fuel/air mixing. To tackle this challenge, the CEFRC assembled a world-class team of 15 principal investigators, with the objectives to: 1) develop and test theoretical models to predict elementary reaction rates, molecule thermalization rates, chemical bond dissociation energies, and nonequilibrium transport properties using quantum chemistry calculations that account for strong electron correlation and multiple electronic potential energy surfaces; 2) develop automated kinetic mechanism generation, reduction, and error control methods for predicting alternative fuel including biofuel oxidation, fuel droplet decomposition, and NOx and particulate formation; 3) validate and improve the predictions of these models by measuring ignition delay times, species profiles, flame structures, burning limits, turbulence-kinetic coupling, and NOx and soot emissions at high-pressures and near-limit conditions, by using advanced experimental diagnostic techniques including multiple laser techniques, molecular beam sampling and synchrotron photoionization, and by conducting the measurements in high-pressure shock tubes, jet-stirred and flow reactors, flame bombs, counterflow flames, and advanced-design rapid compression ignition instruments; and 4) develop a suite of validated petascale high-fidelity simulation and modeling capabilities to understand and predict chemistry-turbulence-radiation coupling for new fuels in new regimes, including the high pressure, low-temperature combustion in advanced engine and turbine designs, and 5) establish a knowledge highway between researchers and engineers in academia, national laboratories, and industry to facilitate the dissemination and exchange of knowledge on national and international levels, and enrich the talent pool and capabilities of the next generation of combustion scientists and engineers. The technical activities of the CEFRC were conducted through three Disciplinary Working Groups – Chemistry Theory, Experiment and Mechanism, and Reacting Flows, which coordinated the Center’s research on the development of combustion chemistry of Foundation Fuels (C0–C4 hydrocarbons), Alcohols, and Biodiesel through three corresponding Mechanism Thrust Groups. Such a two-dimensional coordinated and tightly interwoven research structure has been proven to be highly effective in assuring the interplay between the developments of the fundamentals of combustion science and the utilization of the various categories of fuels. The Center has accomplished the above goals over the five year period (August 1, 2009 – July 31, 2014) with appropriated funding, followed by two additional no-cost-extension (NCE) years. The research results are documented in 230 journal publications, with six legacy review papers on the study of combustion chemistry using shock tubes, flow reactors, rapid compression machines, and flames, on uncertainty quantification, and on theoretical reaction dynamics and chemical modeling of combustion. A robust outreach program complemented these PI-led research activities, consisting of: 1) a roving post-doc program comprised of a corps of Center-appointed, co- or multi-sponsored post-doctoral fellows with rotating assignments to conduct seed projects initiated by at least two PIs, in residence with these sponsoring PIs, to rapidly pursue new and high-risk, high-payoff interdisciplinary ideas; 2) an annual summer school on combustion heavily attended (~200) by senior graduate students and practicing researchers covering advanced topics on chemical kinetics, fluid mechanics, turbulent combustion, engine combustion, new technologies, etc.; 3) a robust open web-site providing Center and community information as well as the lecture videos and notes of the summer school; and 4) widely distributed biannual newsletters.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1993

Operational radiological support for the US manned space program

Radiological support for the manned space program is provided by the Space Radiation Analysis Group at NASA/JSC. This support ensures crew safety through mission design analysis, real-time space environment monitoring, and crew exposure measurements. Preflight crew exposure calculations using mission design information are used to ensure that crew exposures will remain within established limits. During missions, space environment conditions are continuously monitored from within the Mission Control Center. In the event of a radiation environment enhancement, the impact to crew exposure is assessed and recommendations are provided to flight management. Radiation dosimeters are placed throughout the spacecraft and provided to each crewmember. During a radiation contingency, the crew could be requested to provide dosimeter readings. This information would be used for projecting crew dose enhancements. New instrumentation and computer technology are being developed to improve the support. Improved instruments include tissue equivalent proportional counter (TEPC)-based dosimeters and charged particle telescopes. Data from these instruments will be telemetered and will provide flight controllers with unprecedented information regarding the radiation environment in and around the spacecraft. New software is being acquired and developed to provide 'smart' space environmental data displays for use by flight controllers.

Golightly, Michael J.↗

NASA NTRS2005

Failure Assessment

Three questions to which software developers want accurate, precise answers are "How can the software system fail?", "mat bad things will happen if the software fails?t', and "How many failures will the software experience?". Numerous techniques have been devised to answer these questions; three of the best known are: 1) Software Fault Tree Analysis (SFTA) 2) Software Failure Modes, Effects, and Criticality Analysis (SFMECA 3) Software Fault/Failure Modeling. SFTA and SFMECA have been successfully used to analyze the flight software for a number of robotic planetary exploration missions, including Galileo, Cassini, and Deep Space 1. Given the increasing interest in reusing software components from mission to mission, one of us has developed techniques for reusing the corresponding portions of the SFTA and SFMECA, reducing the effort required to conduct these analyses. SFTA has also been shown to be effective in analyzing the security aspects of software systems; intrusion mechanisms and effects can easily be modeled using these techniques. The Bi- Directional Safety Analysis (BDSA) method combines a forward search (similar to SFMECA) from potential failure modes to their effects, with a backward search (similar to SFTA) from feasible hazards to the contributing causes of each hazard. BDSA offers an efficient way to identify latent failures. Recent work has extended BDSA to product-line applications such as flight-instrumentation displays and developed tool support for the reuse of the failure-analysis artifacts within a product line. BDSA has also been streamlined to support those projects having tight cost and/or schedule constraints for their failure analysis efforts. We discuss lessons learned from practice, describe available tools, and identi@ some future directions for the topic. A substantial amount of research has been devoted to estimating the number of failures that a software system will experience during test and operations, as well as the number of faults that have been inserted into that system during its development. One of us has found that the amount of structural change to a system during its development is strongly related to the number of faults inserted into it. Using techniques requiring no additional effort on the part of the development organization, the required measurements of structural evolution can be easily obtained from a development effort's configuration management system and readily transformed into an estimate of fault content. So far, structure-fault relationships have been identified for source code; current work seeks to examine artifacts available earlier in the lifecycle to determine if similar relationships between structure and fault content can be found. In particular, relationships between requirements change requests and the number of faults inserted into the implemented system would provide a significant improvement in our ability to control software quality during the early development phases.

fault tree↗

DOE OSTI2019

Solar Resource Calibration, Measurement, and Dissemination: Final Report FY 2016-FY 2018

The Solar Resource Calibration, Measurement, and Dissemination project supports the U.S. Department of Energy's Solar Energy Technologies Office (SETO) initiative to make solar energy cost-competitive with other forms of electricity by improving the tools and methods to measure and model solar radiation and therefore reduce uncertainty in predicting solar output and improve the bankability of solar projects. This project has three tasks that conduct research on advancing solar resource measurements and modeling: Task 1: Applied solar Radiation Measurements. Task 2: National Solar Radiation Data Base (NSRDB). Task 3: Knowledge Sharing. The National Renewable Energy Laboratory's (NREL's) Solar Radiation Research Laboratory (SRRL) activities ensure traceable solar measurements throughout the United States that are essential for project feasibility, due diligence, financing, and plant operations. The SRRL houses NREL's Baseline Measurement System (BMS), which provides a platform for improving the accuracy of solar measurements through research to improve the calibration and characterization of instruments and enable the development of new measurement technology and standards. The platform contains a variety of instruments measuring solar radiation and other meteorological parameters. Following best practices, BMS instruments are calibrated to ensure traceability to the World Radiometric Reference in compliance with ISO/IEC 17025 accreditation requirements. The BMS data sets are quality-controlled and made publicly available through the Measurement and Instrumentation Data Center website. The NSRDB is the most accessed public database of solar irradiance and associated weather parameters for use in energy modeling. It supports SETO's goals of reducing barriers to high penetrations of solar technologies by providing easy access to high-quality, foundational data essential for innovative product development and downstream modeling through the NSRDB website. Data are currently available for the contiguous United States and beyond for 20 years covering 1998-2017. The Physical Solar Model (PSM) that underpins the current NSRDB data sets is a unique physics-based model that has been developed at NREL and has opened the door to the use of next-generation satellite data sets for solar resource assessment and forecasting. Through the American Society for Testing Materials (ASTM) International and other international standards organizations, NREL continues to provide leadership in the development of standards that are relevant to the measurement and modeling of solar radiation for solar energy applications. Standards developed cover the calibration method of pyrheliometers (direct normal irradiance measurements), pyranometers (global horizontal irradiance measurements), spectroradiometers, ultraviolet radiometers, correct field deployment of these instruments, spectral distribution reference tables for photovoltaic modeling, and transfer of indoor calibrations. Further, NREL leads the International Energy Agency (IEA) Photovoltaic Power Systems Programme Task 16: Subtask 1, which focuses on the evaluation of current and emerging resource assessment methodologies. NREL and the IEA updated the Best Practices Handbook for the Collection and Use of Solar Resource Data for Solar Energy Applications, which is widely used by the solar industry.

14 SOLAR ENERGY↗

NASA NTRS2010

Advanced Spectroscopic and Thermal Imaging Instrumentation for Shock Tube and Ballistic Range Facilities

The Electric Arc Shock Tube (EAST) facility and Hypervelocity Free Flight Aerodynamic Facility (HFFAF, an aeroballistic range) at NASA Ames support basic research in aerothermodynamic phenomena of atmospheric entry, specifically shock layer radiation spectroscopy, convective and radiative heat transfer, and transition to turbulence. Innovative optical instrumentation has been developed and implemented to meet the challenges posed from obtaining such data in these impulse facilities. Spatially and spectrally resolved measurements of absolute radiance of a travelling shock wave in EAST are acquired using multiplexed, time-gated imaging spectrographs. Nearly complete spectral coverage from the vacuum ultraviolet to the near infrared is possible in a single experiment. Time-gated thermal imaging of ballistic range models in flight enables quantitative, global measurements of surface temperature. These images can be interpreted to determine convective heat transfer rates and reveal transition to turbulence due to isolated and distributed surface roughness at hypersonic velocities. The focus of this paper is a detailed description of the optical instrumentation currently in use in the EAST and HFFAF.

Grinstead, Jay H.↗

NASA NTRS2010

Advanced Spectroscopic and Thermal Imaging Instrumentation for Shock Tube and Ballistic Range Facilities

Grinstead, Jay H.↗

NASA NTRS1993

Physics of debris clouds from hypervelocity impacts

The protection scheme developed for long duration space platforms relies primarily upon placing thin metal plates or 'bumpers' around flight critical components. The effectiveness of this system is highly dependent upon its ability to break up and redistribute the momentum of any particle which might otherwise strike the outer surface of the spacecraft. Therefore it is of critical importance to design the bumpers such that maximum dispersion of momentum is achieved. This report is devoted to an in-depth study into the design and development of a laboratory instrument which would permit the in-situ monitoring of the momentum distribution as the impact event occurs. A series of four designs were developed, constructed and tested culminating with the working instrument which is currently in use. Each design was individually tested using the Space Environmental Effects Facility (SEEF) at the Marshall Space Flight Center in Huntsville, Alabama. Along with the development of the device, an experimental procedure was developed to assist in the investigation of various bumper materials and designs at the SEEF. Preliminary results were used to compute data which otherwise were not experimentally obtainable. These results were shown to be in relative agreement with previously obtained values derived through other methods. The results of this investigation indicated that momentum distribution could in fact be measured in-situ as the impact event occurred thus giving a more accurate determination of the effects of experimental parameters on the momentum spread. Data produced by the instrument indicated a Gaussian-type momentum distribution. A second apparatus was developed and it was placed before the shield in the line of travel utilized a plate to collect impact debris scattered backwards. This plate had a passage hole in the center to allow the particle to travel through it and impact the proposed shield material. Applying the law of conservation of angular momentum a backward momentum vector was determined from the angular velocity of the plate. The forward scattered and backward scattered momentum values were then analyzed to judge the distribution of debris. Loss of momentum was attributed to the inaccuracies of the means of measurement. Assumptions of symmetrical debris for the forward and backward scattered directions also contributed to this loss.

Zee, Ralph↗