Search NASA⌕ Search

SEARCH · Search NASA

Results for “corrected data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Learjet 25D Jet Noise Flyover Measurements: Comparisons with Scale-Model Data

Continued interest in commercial supersonic flight has highlighted the need for accurate jet-noise predictions as jet noise is expected to be a dominant noise source for aircraft takeoff conditions. The current study compares the acoustic spectra obtained from a scale-model investigation to that from a Learjet 25D flyover test. Reasonable agreement was achieved between the scale-model and flight data in both peak level and frequency when the physical scale factor for the scale-model was increased by roughly 6%. The peak perceived noise levels (PNL) for the flight data were between 1.29 dB and 1.65 dB higher than those for the scale model. The roll-off of PNL with time for large emission angles was greater for the flight data than for the scale-model data. Using a distributed source model for shear-layer-refraction corrections to the scale-model data slightly improved comparisons to flight data at low frequencies for emission angles near 70° and between 110° and 130°. Distributed source models had no impact on the scale-model spectra near the peak jet-noise angle. Applying a stretching factor to the distributed source models to capture the effects of a flight stream had a very limited impact on the computed spectra.

Acoustics↗
NASA NTRS1986

Evaluation of geophysical parameters measured by the Nimbus-7 microwave radiometer for the TOGA Heat Exchange Project

The data distributed by the National Space Science Data Center on the Geophysical parameters of precipitable water, sea surface temperature, and surface-level wind speed, measured by the Scanning Multichannel Microwave Radiometer (SMMR) on Nimbus-7, are evaluated with in situ measurements between Jan. 1980 and Oct. 1983 over the tropical oceans. In tracking annual cycles and the 1982-83 E1 Nino/Southern Oscillation episode, the radiometer measurements are coherent with sea surface temperatures and surface-level wind speeds measured at equatorial buoys and with precipitable water derived from radiosonde soundings at tropical island stations. However, there are differences between SMMR and in situ measurements. Corrections based on radiosonde and ship data were derived supplementing correction formulae suggested in the databook. This study is the initial evaluation of the data for quantitative description of the 1982-83 E1 Nino/Southern Oscillation episode. It paves the way for determination of the ocean-atmosphere moisture and latent heat exchanges, a priority of the Tropical Ocean and Global Atmosphere (TOGA) Heat Exchange Program.

Liu, W. Timothy↗
NASA NTRS1993

Bonner Durchmusterung (Southern Durchmusterung)

The Southern Durchmusterung (SD, Schoenfeld 1886, Becker 1949, Schmidt 1967) is a visual survey of stars in the declination zones -02 to -23 deg, completed as an extension to Argelander's (1859-62) monumental Bonner Durchmusterung (BD). Schoenfeld's survey was carried out using the same methods as had been used for the BD. The procedure consisted of allowing the telescope to drift along the mean declination of each zone and recording the positions and magnitudes of stars crossing the transit line of each field. The goal of the survey was to extend the BD to declination -23 deg (a plan originally adopted by Argelander) with approximately the same magnitude limits, although the primary instrument was of larger aperture (159 mm) than the 78-mm telescope used for the BD. Thus, whereas the BD magnitude estimates extend to 9.4 mag with all fainter stars assigned a magnitude of 9.5, the SD magnitude estimates extend to 9.9 mag with all fainter stars assigned a magnitude of 10. The SD contains a number of stars fainter than 10.0 mag and even some as faint as 11 mag. Lists of all corrections made to the original data as a result of published corrigenda, stars deleted according to overstriking in the printed catalogs or their inclusion in lists of 'missing' stars, and stars inserted in later editions are given. No other corrections or changes have been incorporated into the original data, e.g., from more modern positions and magnitudes or from comparison with other catalogs.

Source record↗
NASA NTRS1984

TM Failed Detectors Data Replacement

Some of the LANDSAT 4 Thematic Mapper detectors (band 2 detector 4 and band 5 detector 3) have inadequate performances. The operational system correction processing will disregard the data sensed by the failed detectors and replace them by data coming from the neighbor detectors of the same spectra band. The analysis performed by ESA Earthnet and attempts to suggest an operational failed detector replacement algorithm are described.

Fusco, L.↗
DOE OSTI2025

Comparisons of the v11.1 Orbiting Carbon Observatory‐2 (OCO‐2) X CO2 Measurements With GGG2020 TCCON

The Orbiting Carbon Observatory 2 (OCO-2) is NASA's first Earth observation satellite mission dedicated to studying the sources and sinks of carbon dioxide (CO 2 ) on a global scale. The observations of reflected sunlight are inverted in a retrieval algorithm to produce estimates of the dry air mole-fractions of CO 2 (X CO2 ). The OCO-2 Level 2 data release, version 11.1 (v11.1) retrievals from the Atmospheric Carbon Observations from Space (ACOS) algorithm, includes significant improvements in the X CO2 data product compared to older OCO-2 data versions. This work compares the v11.1 X CO2 from OCO-2 against X CO2 estimates collected from a global ground-based network known as the Total Carbon Column Observing Network (TCCON), OCO-2's primary validation source. The OCO-2 project provides a version of the Level 2 data product, called “lite” files that include calibrated and bias-corrected XCO2 values, accessible together with all OCO-2 data products through the NASA Goddard Earth Sciences Data and Information Services Center (GES DISC). This work shows that OCO-2 X CO2 observations made between September 2014 and December 2023, after quality filtering and the application of an averaging kernel correction, agree well with coincident TCCON data for all OCO-2 observational modes of land (nadir, glint, target) and ocean (glint). The aggregated, bias-corrected, and quality-filtered absolute average bias values are less than or equal to 0.20 parts per million (ppm) globally for all OCO-2 observation modes, where the biases do not indicate a statistically significant time dependence. The land nadir/glint mode has the lowest bias value of −0.03 ± 0.85 ppm.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Overestimation of Mach number due to probe shadow

Comparisons of the plasma ion flow speed measurements from Mach probes and laser induced fluorescence were performed in the Controlled Shear Decorrelation Experiment. We show the presence of the probe causes a low density geometric shadow downstream of the probe that affects the current density collected by the probe in collisional plasmas if the ion-neutral mean free path is shorter than the probe shadow length, L g = w 2 V drift /D ⊥ , resulting in erroneous Mach numbers. We also present a simple correction term that provides the corrected Mach number from probe data when the sound speed, ion-neutral mean free path, and perpendicular diffusion coefficient of the plasma are known. The probe shadow effect must be taken into account whenever the ion-neutral mean free path is on the order of the probe shadow length in linear devices and the open-field line region of fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2015

OSOAA: A Vector Radiative Transfer Model of Coupled Atmosphere-Ocean System for a Rough Sea Surface Application to the Estimates of the Directional Variations of the Water Leaving Reflectance to Better Process Multi-angular Satellite Sensors Data Over the Ocean

In this study, we present a radiative transfer model, so-called OSOAA, that is able to predict the radiance and degree of polarization within the coupled atmosphere-ocean system in the presence of a rough sea surface. The OSOAA model solves the radiative transfer equation using the successive orders of scattering method. Comparisons with another operational radiative transfer model showed a satisfactory agreement within 0.8%. The OSOAA model has been designed with a graphical user interface to make it user friendly for the community. The radiance and degree of polarization are provided at any level, from the top of atmosphere to the ocean bottom. An application of the OSOAA model is carried out to quantify the directional variations of the water leaving reflectance and degree of polarization for phytoplankton and mineral-like dominated waters. The difference between the water leaving reflectance at a given geometry and that obtained for the nadir direction could reach 40%, thus questioning the Lambertian assumption of the sea surface that is used by inverse satellite algorithms dedicated to multi-angular sensors. It is shown as well that the directional features of the water leaving reflectance are weakly dependent on wind speed. The quantification of the directional variations of the water leaving reflectance obtained in this study should help to correctly exploit the satellite data that will be acquired by the current or forthcoming multi-angular satellite sensors.

Ocean surface↗
NASA NTRS1996

Evaluation of IGS Orbits with Satellite Laser Ranging

The accuracy with which orbits for the Global Positioning System (GPS) spacecraft, can be computed directly affects the accuracy of the resulting site coordinates and polar motion. Several groups routinely analyze GPS ground tracking data to compute precise orbits and terrestrial reference frame solutions. In this paper, we infer the accuracy of the orbits of two of the GPS satellites by comparing to independent laser ranges of subcentimeter accuracy obtained by a small but reasonably well distributed network of tracking sites. We find that all seven International GPS Service for Geodynamics (IGS) analysis centers achieve range residual root mean square (rms) errors at or below the 100 mm level. The best orbit solutions, from JPL, CODE, and the IGS combined product, yield a residual rms of about 50 mm. These residuals are consistent with three dimensional orbit errors of less than 150 mm. Estimating yaw rates for the spacecraft during shadow events, and using these estimates to compute the laser residual, significantly improves the fit. A small mean residual value of -15 to -30 mm seems to exist for most centers and laser sites which is not fully explained at present, but may be due to uncertainties in the corrections to the laser data, such as the reflector to spacecraft center of mass vector or small reference frame differences between the SLR sites and the GPS orbits.

Watkins, M. M.↗
DOE OSTI2023

New method for level-lifetime measurements with thick scintillators

Level lifetimes provide key insight into the structure of atomic nuclei and serve as stringent tests of theoretical descriptions. Though several methods for determining level lifetimes exist for both reaction measurements and decay studies, here the focus is on techniques involving the direct measurement of time differences between population and subsequent depopulation of excited states. The techniques presented herein are broadly applicable across multiple timing ranges, but the approach is specifically described for the βγ timing method. A multi-step, amplitude-dependent time walk correction was employed to address the data analysis complications that arise from using thick scintillators for electron detection. Further, additional corrections for the depth of the interaction must also be performed when the parent isotope has been implanted into the detector. Techniques are presented for performing these time walk and depth of interaction corrections. Subsequently, a new Monte Carlo method utilizing measured detector responses obtained from the data, coupled with chi-square minimization, is presented for extracting excited state lifetimes ≳ 100 picoseconds. The framework of this Monte Carlo method is developed for the decay of a state in 68 Zn with a known 1.6 ps half life, which is considered prompt given the detection sensitivity of the technique, and then benchmarked using two other excited states in neutron-rich Ni isotopes with 120(34) ps and 1.05(3) ns half lives. Using this new method which takes into account the thick scintillator used, these same half lives were measured to be 135(10) ps and 1.04(24) ns, respectively. The overall good agreement demonstrates the validity of the technique.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

Ring current pressure estimation with RAM-SCB using data assimilation and Van Allen Probe flux data

Capturing and subsequently modeling the influence of tail plasma injections on the inner magnetosphere is important for understanding the formation and evolution of the ring current. In this study, the ring current distribution is estimated with the Ring Current–Atmosphere Interactions Model with Self–Consistent Magnetic field (RAM–SCB) using, for the first time, data assimilation techniques and particle flux data from the Van Allen Probes. The state of the ring current within the RAM–SCB model is corrected via an ensemble based data assimilation technique by using proton flux from one of the Van Allen Probes, to capture the enhancement of the ring current following an isolated substorm event on 18 July 2013. The results show significant improvement in the estimation of the ring current particle distributions in the RAM–SCB model, leading to better agreement with observations. Furthermore, this newly implemented data assimilation technique in the global modeling of the ring current thus provides a promising tool to improve the characterization of particle distribution in the near–Earth regions.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Utah FORGE: Triaxial Direct Shear Results - February 2025

This dataset contains results from nine triaxial direct shear tests conducted by Los Alamos National Laboratory on samples from FORGE Well 16A(78)-32. The primary objectives of this work were to determine the shear strength in both intact and residual states, evaluate dilation against displacement, assess permeability in relation to displacement, time, and normal stress, understand the relationship between aperture and normal stress, and monitor the effluent chemistry as a function of time. The data includes time-series measurements of stress, displacement, permeability, and effluent chemistry, with and without experimental dilution corrections. Additional materials include profilometry data, photographic documentation of the experimental setups and apparatus, and test notes. The dataset is organized into folders corresponding to each test, containing hydromechanical data, effluent chemistry measurements, and images. The hydromechanical data consists of detailed time-series records capturing parameters such as shear force, confining pressure, permeability, and temperature. Effluent chemistry data tracks fluid composition changes over time. Also included are conference papers, presentation slides, and a summary document outlining the experiments.

15 GEOTHERMAL ENERGY↗
NASA NTRS1974

Liquid rocket combustion computer model with distributed energy release. DER computer program documentation and user's guide, volume 1

A computer program for analyzing rocket engine performance was developed. The program is concerned with the formation, distribution, flow, and combustion of liquid sprays and combustion product gases in conventional rocket combustion chambers. The capabilities of the program to determine the combustion characteristics of the rocket engine are described. Sample data code sheets show the correct sequence and formats for variable values and include notes concerning options to bypass the input of certain data. A seperate list defines the variables and indicates their required dimensions.

Combs, L. P.↗
NASA NTRS1990

Cloud parameters from GOES visible and infrared radiances during the FIRE Cirrus IFO, October 1986

Visible (VIS, 0.65 micron) and infrared (IR, 10.5 microns) channels on geostationary satellites are the key elements of the International Satellite Cloud Climatology Project (ISCCP). All daytime ISCCP cloud parameters are derived from a combination of VIS and IR data. Validation and improvement of the ISCCP and other cloud retrieval algorithms are important components of the First ISCCP Regional Experiment (FIRE) Intensive Field Observations (IFO). Data from the Cirrus IFO (October 19 to November 2, 1986) over Wisconsin are available for validating cirrus cloud retrievals from satellites. The Geostationary Operational Environmental Satellite (GOES) located over the Equator at approximately 100 deg W provided nearly continuous measurements of VIS and IR radiances over the IFO areas. The preliminary results of cloud parameters derived from the IFO GOES data are presented. Cloud attitudes are first derived using an algorithms without corrections for cloud emissivity. These same parameters will then be computed from the same data relying on an emissivity correction algorithm based on correlative data taken during the Cirrus IFO.

Heck, Patrick W.↗
NASA NTRSDate not supplied

Error Localization Examples: Looking for a Needle in a Hay-stack

Finite element models (FEM) are routinely developed and used during fabrication of high dollar-value hardware. NASA as part of the pre-flight certification of launch vehicles routinely conducts vibration and static tests to calibrate models used for flight-risk assessments. As part of the calibration process, certain areas in the model are modified, using engineering judgment and sensitivity analysis, to match the test results. Unfortunately, tools to identify problem areas in the FEM using test data directly are scarce. Over the years, Error Localization Algorithms (ELA) have been proposed with very limited success. Recently, the Analytical Dynamics Model Improvement (ADMI) algorithm, which computes closed-form mass and stiffness corrections to match the test data exactly, have been shown to be effective for error localization. The paper will present several FEM example problems where ELA is used with simulated test data to determine FEM problem areas. For each example, the correct answer is shown along with ELA results. It is shown that the ELA process is able to identify general problem areas in the FEM, which are consistent with known model perturbations. However, in most cases the ELA identified area of improvement is larger than the true answer. Nonetheless, with proper optimization tools, calibration results using the ELA identified areas provide excellent results.

error localization↗
DOE OSTI2015

Note: An improved calibration system with phase correction for electronic transformers with digital output

The existing electronic transformer calibration systems employing data acquisition cards cannot satisfy some practical applications, because the calibration systems have phase measurement errors when they work in the mode of receiving external synchronization signals. This paper proposes an improved calibration system scheme with phase correction to improve the phase measurement accuracy. We employ NI PCI-4474 to design a calibration system, and the system has the potential to receive external synchronization signals and reach extremely high accuracy classes. Accuracy verification has been carried out in the China Electric Power Research Institute, and results demonstrate that the system surpasses the accuracy class 0.05. Furthermore, this system has been used to test the harmonics measurement accuracy of all-fiber optical current transformers. In the same process, we have used an existing calibration system, and a comparison of the test results is presented. The system after improvement is suitable for the intended applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2018

Estimation of TETRA radio use in the Airwave Health Monitoring Study of the British police forces

Highlights: • Operator-derived records alongside self-reported information to estimate radio use as a proxy for RF-EMF exposure. • Imputed average TETRA radio usage correlates better with objective data than self-reported use. • Higher personal radio usage seen in younger and male participants as well as in police officers compared with staff. • The first large observational study with an estimate of monthly average personal radio usage for all participants. The Airwave Health Monitoring Study aims to investigate the possible long-term health effects of Terrestrial Trunked Radio (TETRA) use among the police forces in Great Britain. Here, we investigate whether objective data from the network operator could be used to correct for misreporting in self-reported data and expand the radio usage availability in our cohort.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2021

Evaluation of Thermal Neutron Scattering Cross Sections for CaH 2

Solid metal hydrides have long been considered viable moderators for nuclear reactor designs due to their moderating ratios, hydrogen densities, high dissociation temperatures, and mechanical properties. CaH 2 is an orthorhombic saline-hydride that has recently been investigated and shows promise for use as a moderator in microreactors. At present, there is no Thermal Scatting Law (TSL) evaluation for CaH 2 in the ENDF/B-VIII.0 database. An evaluation does exist in the JEFF-3.3 database, performed by Serot, however it was limited by the implemented methods and thus both drastically over-predicts the incoherent elastic contribution and completely ignores the coherent elastic contribution to scattering from the metal ions. The thermal neutron scattering cross sections of CaH 2 are evaluated in this work to establish accurate data for use in reactor design. The present evaluation corrects the inaccuracies of the JEFF-3.3 data, and yields three distinct libraries: Ca in CaH 2 , H 1 in CaH 2 , and H 2 in CaH 2 .

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2022

Fire Island Water Resources: Assessing Sediment Dynamics and Turbidity Changes Along Fire Island National Seashore Using Satellite Data

Fire Island National Seashore has experienced damaging effects as a result of coastal erosion. Erosion has become an increasingly damaging problem that has led to the destruction of park and community infrastructure, contributed to rising groundwater tables, and posed a serious threat to a globally rare holly maritime forest. Beach nourishment project efforts have been made to mitigate damage, but dredging is expensive and can be thwarted by high rates of erosion. The NASA DEVELOP team partnered with the National Park Service and Fire Island National Seashore and used imagery from Landsat 5 Thematic Mapper (TM), Landsat 8 Operational Land Imager (OLI), and Sentinel-2 MultiSpectral Instrument (MSI) to analyze turbidity and sediment dynamics through surface reflectance data from 2000-2021. Imagery was atmospherically corrected using Atmospheric Correction for OLI Lite (ACOLITE) and visualized in SeaWiFS Data Analysis Systems (SeaDAS). Additionally, shoreline change was analyzed using high-resolution imagery from WorldView-2 acquired from Maxar for pre-Hurricane Sandy on July 25th, 2010 and post-Hurricane Sandy on December 18th, 2019. The results of this analysis showed that turbidity is highest in the winter seasons. The shoreline analysis estimated total shoreline loss of about 62 acres on the ocean side, and 11 acres on the bay side of the island. These results will be used to better inform future partner-designed shoreline management projects in the face of further erosion and sea level rise.

Kelly Young↗