Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Scale model testing of the jet noise characteristics of the JT8D refan engine nozzle system

The results are presented of static scale model acoustic tests of the nozzle system for the JT8D-9 baseline engine and candidate nozzle systems for JT8D-109, JT8D-115, and JT8D-117 refan engines. The objective of these tests was to determine the jet noise benefit of the three refan engine cycles relative to the baseline JT8D-9, and to provide acoustic information toward selection of the optimum primary-secondary area match and centerbody contour for the refan engine cycles. One of the nozzle configurations was tested with and without simulated turbine exit swirl to determine what effect, if any, swirl has no jet noise. The JT8D-109 cycle was found to afford approximately 9 db (0ASPL) jet noise reduction relative to the JT8D-9 when compared on an equal static thrust basis. The JT8D-115 and JT8D-117 afford an 8 db and 6 db reduction, respectively, relative to the JT8D-9, at equal static thrust. Turbine exit swirl was found to have no significant effect on the jet noise of the JT8D-109 nozzle system.

Reed, D. H.↗

Interim prediction method for low frequency core engine noise

A literature survey on low-frequency core engine noise is presented. Possible sources of low frequency internally generated noise in core engines are discussed with emphasis on combustion and component scrubbing noise. An interim method is recommended for predicting low frequency core engine noise that is dominant when jet velocities are low. Suggestions are made for future research on low frequency core engine noise that will aid in improving the prediction method and help define possible additional internal noise sources.

Huff, R. G.↗

Comparison of parametric duct-burning turbofan and non-afterburning turbojet engines in a Mach 2.7 transport

A parametric study was made of duct-burning turbofan and suppressed dry turbojet engines installed in a supersonic transport. A range of fan pressure ratios was considered for the separate-flow-fan engines. The turbofan engines were studied both with and without jet noise suppressors. Single- as well as dual-stream suppression was considered. Attention was concentrated on designs yielding sideline noises of FAR 36 (108 EPNdB) and below. Trades were made between thrust and wing area for a constant takeoff field length. The turbofans produced lower airplane gross weights than the turbojets at FAR 36 and below. The advantage for the turbofans increased as the sideline noise limit was reduced. Jet noise suppression, especially for the duct stream, was very beneficial for the turbofan engines as long as duct burning was permitted during takeoff. The maximum dry unsuppressed takeoff mode, however, yielded better results at extremely low noise levels. Noise levels as low as FAR 36-11 EPNdB were obtained with a turbofan in this takeoff mode, but at a considerable gross weight penalty relative to the best FAR 36 results.

Whitlow, J. B., Jr.↗

Experimentally-determined external heat loss of automotive gas turbine engine

An external heat balance was conducted on a 150 HP two-shaft automotive gas turbine engine. The engine was enclosed in a calorimeter box and the temperature change of cooling air passing through the box was measured. Cooling airflow ranges of 1.6 to 2.1 lb-per-second and 0.8 to 1.1 lb-per-second were used. The engine housing heat loss increased as the cooling airflow through the calorimeter box was increased, as would be the case in a moving automobile. The heat balance between the total energy input and the sum of shaft power output and various losses compared within 30 percent at engine idle speeds and within 7 percent at full power.

Meng, P. R.↗

The predicament of aeronautical engineering education and what we can do about it

An analysis of the aeronautical engineering situation and the relationship to the U.S. aircraft industry is presented. Some of the problems encountered in undergraduate aeronautical engineering education are explained. A reorganization of the educational structure for aeronautical engineering is proposed. The human factors aspect of aeronautical engineering discipline is described.

Bryson, A. E., Jr.↗

Engine systems technology

Current full-scale engine development programs are discussed, and efforts to improve the available technology base are presented. The Lewis full-scale engine test facilities are described. Several typical engine programs and plans for research in aeromechanical instability or flutter are summarized. An overview of Lewis studies of flow distortion and its effects on engine stability is presented. The origins and nature of the distortion problem are summarized, and some of the results and methods for both steady and time-varying distortions are discussed.

Willoh, R.↗

Motion-base simulator study of control of an externally blown flap STOL transport aircraft after failure of an outboard engine during landing approach

A moving-base simulator investigation of the problems of recovery and landing of a STOL aircraft after failure of an outboard engine during final approach was made. The approaches were made at 75 knots along a 6 deg glide slope. The engine was failed at low altitude and the option to go around was not allowed. The aircraft was simulated with each of three control systems, and it had four high-bypass-ratio fan-jet engines exhausting against large triple-slotted wing flaps to produce additional lift. A virtual-image out-the-window television display of a simulated STOL airport was operating during part of the investigation. Also, a simple heads-up flight director display superimposed on the airport landing scene was used by the pilots to make some of the recoveries following an engine failure. The results of the study indicated that the variation in visual cues and/or motion cues had little effect on the outcome of a recovery, but they did have some effect on the pilot's response and control patterns.

Middleton, D. B.↗

Gaseous exhaust emissions from a JT8D-109 turbofan engine at simulated cruise flight conditions

Gaseous emissions from a JT8D-109 turbofan engine were measured in an altitude facility at four simulated cruise flight conditions: Mach 0.8 at altitudes of 9.1, 10, 7, and 12.2 km and Mach 0.9 at 10.7 km. Engine inlet air temperature was held constant at 283 K for all tests. Emissions measurements were made at nominally 6 cm intervals across the horizontal diameter of the engine exhaust nozzle with a single-point traversing gas sample probe. Measured emissions of decreased with increasing altitude from an emission index of 10.4 to one of 8.3, while carbon monoxide increased with increasing altitude from an emission index of 1.6 to one of 4.4. Unburned hydrocarbon emissions were essentially negligible for all flight conditions. Since the engine inlet air temperatures were not correctly simulated, the NOx emission indices were corrected to true altitude conditions by using correlating parameters for changes in combustor inlet temperature, pressure, and temperature rise. The correction was small at the lowest altitude. At the 10.7 and 12.2 km, Mach 0.8 test conditions the correction decreased the measured values by 1 emission index.

Diehl, L. A.↗

Emission calibration of a J-58 afterburning turbojet engine at simulated supersonic, stratospheric flight conditions

Emissions of total oxides of nitrogen, unburned hydrocarbons, and carbon monoxide from a J-58 engine at simulated flight conditions of Mach 2.0, 2.4, and 2.8 at 19.8 km altitude are reported. For each flight condition, measurements were made for four engine power levels from maximum power without afterburning through maximum afterburning. These measurements were made 7 cm downstream of the engine primary nozzle using a single point traversing gas sample probe. Results show that emissions vary with flight speed, engine power level, and with radial position across the exhaust.

Holdeman, J. D.↗

Some unusual oscillating bearing applications in liquid propellant rocket engines

Liquid propellant rocket engines have some unique applications for highly loaded oscillating-motion bearings operating at cryogenic temperatures and vacuum environment conditions. Among these are (1) thrust attitude control gimbal bearings that permit pivoting of the entire rocket engine and (2) bearings in the linkages of ducting bellows joints that articulate when the engine gimbals. The main rocket engines for first, second, and third stages of the Saturn vehicle have thrust vector control gimbals which use PTFE liner bearing materials and ducting linkage bearings using solid film dry lubricants, both to reduce friction and provide required wear life. Data on the frictional and wear characteristics of these materials, while operating under varying temperature and atmospheric pressure conditions, are presented. A discussion of the bearing designs for flexible bellows joint linkages is also presented.

Daniels, C. M.↗

Aerodynamic characteristics of a large-scale hybrid upper surface blown flap model having four engines

Data are presented from an investigation of the aerodynamic characteristics of large-scale wind tunnel aircraft model that utilized a hybrid-upper surface blown flap to augment lift. The hybrid concept of this investigation used a portion of the turbofan exhaust air for blowing over the trailing edge flap to provide boundary layer control. The model, tested in the Ames 40- by 80-foot Wind Tunnel, had a 27.5 deg swept wing of aspect ratio 8 and 4 turbofan engines mounted on the upper surface of the wing. The lift of the model was augmented by turbofan exhaust impingement on the wind upper-surface and flap system. Results were obtained for three flap deflections, for some variation of engine nozzle configuration and for jet thrust coefficients from 0 to 3.0. Six-component longitudinal and lateral data are presented with four engine operation and with the critical engine out. In addition, a limited number of cross-plots of the data are presented. All of the tests were made with a downwash rake installed instead of a horizontal tail. Some of these downwash data are also presented.

Carros, R. J.↗

On the effects of flight on jet engine exhaust noise

Differences between flight data and predictions of jet engine exhaust noise were reconciled by considering the combined effects of jet mixing noise and internally generated engine exhaust noise. The source strength of the internally generated noise was assumed to be unaffected by flight, as experiments demonstrated. The directivity of the internally generated noise was assumed to be the same statically as that given in the NASA interim prediction method for core engine noise. However, it was assumed that in flight internally generated noise is subject to the convective amplification effect of a simple source. The absolute levels of internally generated noise were obtained from an empirical fit of some typical engine data. The static and flight jet noise were predicted using the above prediction method. It was shown that in many cases much of the flyover noise signature is dominated by internally generated noise.

Stone, J. R.↗

Small, low-cost, expendable turbojet engine. 1: Design, fabrication, and preliminary testing

A small experimental axial-flow turbojet engine in the 2,669-Newton (600-lbf) thrust class was designed, fabricated, and tested to demonstrate the feasibility of several low-cost concepts. Design simplicity was stressed in order to reduce the number of components and machining operations. Four engines were built and tested for a total of 157 hours. Engine testing was conducted at both sea-level static and simulated flight conditions for engine speeds as high as 38,000 rpm and turbine-inlet temperatures as high as 1,255 K (1,800 F).

Dengler, R. P.↗

On the effects of flight on jet engine exhaust noise

Recent flight data on jet engine exhaust noise do not agree with projections based on classical jet noise theories. This paper demonstrates that these differences may be reconciled by considering the combined effects of jet mixing noise and internally-generated engine exhaust noise. The source strength of the internally-generated noise is assumed to be unaffected by flight, as has been shown in small-scale free-jet experiments. The directivity of the internally-generated noise is assumed to be the same statically as that given in the NASA interim prediction method for core engine noise. However, it is assumed that in flight the internally generated noise is subject to the convective amplification effect of a simple source. The absolute levels of the internally-generated noise are obtained from an empirical fit of some typical engine data. The static and flight jet noise are predicted using the NASA interim prediction method for jet noise. It is shown that in many cases, although jet mixing may be the dominant noise source statically, much of the flyover noise signature is dominated by internally-generated noise.

Stone, J. R.↗

Flight effects on JT8D engine jet noise as measured in the NASA Ames 40-by 80-foot wind tunnel

A JT8D-17 turbofan engine was tested in a 40 x 80 ft wind tunnel to determine flight effects on jet noise. The engine was configured as a baseline with conical nozzle, a quiet nacelle 20-lobe ejector/suppressor, and an internal mixer with conical nozzle. Tunnel-off and tunnel-on noise tests were conducted over a range of nozzle pressure ratios (1.2 to 2.1), primary jet velocities (275 to 550 m/s), and tunnel velocities up to 100 m/s. Aft quadrant noise data were measured by a pair of traversing microphones located on a 3-m sideline relative to the engine centerline. Unique correlations and analysis procedures were developed in order to define far-field flight effects from the relatively near-field noise measurements. The ejector/suppressor experienced a significant loss of suppression relative to static measurements during flight while the internal mixer indicated a slight gain in suppression. It is concluded that the wind tunnel is a viable method for studying flight effects on engine jet noise.

Strout, F. G.↗

The NASA Pollution-Reduction Technology Program for small jet aircraft engines - A status report

A three-phase experimental program is described which has the objective of enabling EPA Class T1 jet engines to meet the 1979 EPA emissions standards. In Phase I, three advanced combustor concepts, designed for the AiResearch TFE 731-2 turbofan engine, were evaluated in screening tests. Goals for carbon monoxide and unburned hydrocarbons were met or closely approached with two of the concepts with relatively modest departures from conventional combustor design practices. A more advanced premixing/prevaporizing combustor, while appearing to have the potential for meeting the oxides of nitrogen goal as well, will require extensive development to make it a practical combustion system. Smoke numbers for the two combustor concepts which will be carried forward into Phase II of the program were well within the EPA smoke standard. Phase II, Combustor-Engine Compatibility Testing, which is in its early stages, and planned Phase III, Combustor-Engine Demonstration Testing, are also described.

Fear, J. S.↗

Aircraft engine weight and dimensions

Program estimates engine weights and major dimensions on compartment to compartment basis for any engine with components that can be represented within the program. Data base of program reflects selected high technology engines from supersonic cruise aircraft research studies, some NASA in-house results, and some older military supersonic engines.

Franciscus, L. C.↗

Method of discrete modeling and its application to estimation of TF30 engine variables

A method of discrete modeling is presented that effectively isolates steady state model accuracy from dynamic model accuracy. The steady state model may be generated from the engine design equations with any desired degree of accuracy. The dynamic model is generated by applying a step disturbance of a manipulated variable to an open loop engine simulation. The sampled response of the variable is combined with the steady state model's response to form a set of weighting factors. These weighting factors are then used to weight past values of the manipulated variable, thus forming the dynamic model. The method is used to estimate various TF30-P-3 engine variables. A dynamic trim function is developed to compensate for the dynamic nonlinearities of the variables as well as for inaccuracies in dynamic definition. The trim function is shown to be realted to the square root of the sum of the squares of the weighting factors obtained at various engine operating conditions. Finally, the estimation of variables without dynamic modeling is discussed.

Arpasi, D. J.↗