Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Strengthening of C/SiC Composites by Electrophoretic Deposition of CNTs on a SiC Coating

The current study reports the enhancement of mechanical properties of carbon fiber-reinforced silicon carbide ceramic matrix composites (C/SiC CMCs) by the application of a carbon nanotube/silicon carbide (CNT/SiC) coating. CNTs were deposited on the surfaces of C/SiC composites using electrophoretic deposition (EPD), after which infiltration by SiC was achieved through a chemical vapor infiltration process. An EPD duration of 5 min was associated with a 40% increase in the ultimate flexural strength relative to that of composites with a pure SiC coating. The observed enhancement was rationalized by the microstructural observations of SiC infiltration into the porous CNT morphology and the subsequent formation of CNT/SiC layers on the surfaces of the composites and by the inherent toughness of the SiC whiskers. The flexural strength decreased with EPD durations greater than 5 min due to the formation of thick CNT meshes, which decreased the open porosity and thereby obstructed further SiC infiltration. This is a viable methodology for the improvement of mechanical properties of CMCs by the introduction of a ceramic coating containing CNT.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermoelectric conversion via laser-induced voltage in highly textured polycrystalline Na{sub x}CoO{sub 2} ceramic

We have studied and analyzed the laser-induced voltage effect in highly c-axis-oriented polycrystalline Na{sub x}CoO{sub 2}. The textured and layered stacking Na{sub x}CoO{sub 2} (x {approx} 0.7) bulks were prepared by a solid-state reaction process. Under the irradiation on Na{sub 0.67}CoO{sub 2} bulk surface with pulsed laser ({lambda} = 248 nm), the induced voltage signals were observed on the inclined surface with rise time 30 ns-43 ns and peak voltage 200 mV-500 mV; the voltage peak values show a linear dependence of laser energy densities. The crystal grains orientation plays a critical role in voltage peak value whether in film or texture bulk. The transverse voltage signal brings the information of thermoelectric anisotropy. In Na{sub x}CoO{sub 2} band structure, the Fermi surface is different in the ab plane and along the c axis, leading to anisotropy of Seebeck coefficient. Additionally, the artificial structure of the inclined surface for highly textured bulk enables us to obtain a transverse voltage on inclined surface. These results demonstrated the layered textured bulk has potential applications in waste-heat conversion via transverse thermoelectric effect.

36 MATERIALS SCIENCE↗

Structural Anomalies Detected in Ceramic Matrix Composites Using Combined Nondestructive Evaluation and Finite Element Analysis (NDE and FEA)

Most reverse engineering approaches involve imaging or digitizing an object and then creating a computerized reconstruction that can be integrated, in three dimensions, into a particular design environment. The rapid prototyping technique builds high-quality physical prototypes directly from computer-aided design files. This fundamental technique for interpreting and interacting with large data sets is being used here via Velocity2 (an integrated image-processing software, ref. 1) using computed tomography (CT) data to produce a prototype three-dimensional test specimen model for analyses. A study at the NASA Glenn Research Center proposes to use these capabilities to conduct a combined nondestructive evaluation (NDE) and finite element analysis (FEA) to screen pretest and posttest structural anomalies in structural components. A tensile specimen made of silicon nitrite (Si3N4) ceramic matrix composite was considered to evaluate structural durability and deformity. Ceramic matrix composites are being sought as candidate materials to replace nickel-base superalloys for turbine engine applications. They have the unique characteristics of being able to withstand higher operating temperatures and harsh combustion environments. In addition, their low densities relative to metals help reduce component mass (ref. 2). Detailed three-dimensional volume rendering of the tensile test specimen was successfully carried out with Velocity2 (ref. 1) using two-dimensional images that were generated via computed tomography. Subsequent, three-dimensional finite element analyses were performed, and the results obtained were compared with those predicted by NDE-based calculations and experimental tests. It was shown that Velocity2 software can be used to render a three-dimensional object from a series of CT scan images with a minimum level of complexity. The analytical results (ref. 3) show that the high-stress regions correlated well with the damage sites identified by the CT scans and the experimental data. Furthermore, modeling of the voids collected via NDE offered an analytical advantage that resulted in more accurate assessments of the material s structural strength. The top figure shows a CT scan image of the specimen test section illustrating various hidden structural entities in the material and an optical image of the test specimen considered in this study. The bottom figure represents the stress response predicted from the finite element analyses (ref .3 ) for a selected CT slice where it clearly illustrates the correspondence of the high stress risers due to voids in the material with those predicted by the NDE. This study is continuing, and efforts are concentrated on improving the modeling capabilities to imitate the structural anomalies as detected.

Abdul-Aziz, Ali↗

Progress in development of SiC-based joints resistant to neutron irradiation

This study fills a knowledge gap regarding neutron-irradiation resistance of SiC joints for nuclear applications, by investigating high-dose neutron irradiation effects on the strength of selected joints and low-dose neutron irradiation effects on recently developed joints fabricated by state of the art processing methods. The joining methods used for the high-dose radiation study included pressure-assisted liquid-phase sintering (LPS) of SiC nanopowder, pressureless calcia-alumina glass ceramics joining, and reaction sintering of Ti-Si-C powders with hot-pressing. The joints were neutron-irradiated at 530 °C to 20 displacements per atom (dpa). Other joining methods included low-pressure LPS of cold-pressed SiC green body, pressureless reaction sintered Ti-Si-C powder joint, spark plasma–sintered Ti diffusion bond, and hot-pressed Ti diffusion bond, which were irradiated at ~500 °C to ~2 dpa. There was no notable degradation of torsional strengths of the joints following the high-dose irradiation. The irradiation-induced degradation at low neutron dose was highly dependent on joint type.

36 MATERIALS SCIENCE↗

Novel yellowish-green emitting luminescence in Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16}:Eu{sup 2+} phosphor

Graphical abstract: The phosphor has two separated emission centers with the dependent emission intensity on Eu{sup 2+} doping. There is a red-shift in the emission due to energy transfer with increasing the Eu{sup 2+}-doping. - Highlights: • Green-origin-emitting phosphors of Eu{sup 2+}-doped Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16} were firstly prepared by chemical sol–gel method. • The tunable luminescence color was realized by the changing Eu{sup 2+}-doping in Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16}. • Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16}:Eu{sup 2+} displays two typical luminescence centers with the emission depending on Eu{sup 2+} doping. • Eu{sup 2+}-doped Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16} phosphor has an excellent thermal stability on the temperature quenching. - Abstract: Color tunable green-origin-emitting phosphor of Eu{sup 2+}-doped phosphate-silicate Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16} was prepared by chemical sol–gel method. The X-ray powder diffraction, the photoluminescence excitation and emission spectra, time resolved spectra, and thermal stability were measured. The excitation spectra can well match with the emission light of near UV-LED chips (360–400 nm). The tunable luminescence was realized by changing Eu{sup 2+}-doping concentration. Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16}:Eu{sup 2+} displays two typical luminescence centers, which were suggested to originate from two Ca{sup 2+} sites in the host. With increasing Eu{sup 2+} doping concentrations, the green emission band shifts to long wavelength. Energy transfer between the two different Eu{sup 2+} ions is discussed by analyzing the photoluminescence excitation and emission spectra, concentration-dependent luminescence intensity, and lifetimes. The dependence of the luminescence intensity of Ca{sub 7}Si{sub 2}P{sub 2}O{sub 16}:Eu{sup 2+} on temperatures was measured. The activation energy (ΔE) for thermal quenching was reported.

36 MATERIALS SCIENCE↗

Lithium stoichiometry of solid electrolytes based on tetragonal Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12}

Graphical abstract: - Highlights: • We prepared Li{sub x}La{sub 3}Zr{sub 2}O{sub 8.5+0.5x} (x = 6, 7, 8, 9, 10) by the citrate–nitrate method. • We studied phase composition and conductivity of Li{sub x}La{sub 3}Zr{sub 2}O{sub 8.5+0.5x}. • We proposed a simple method to determine the carbonate impurity content in the solid electrolytes. • The synthesized solid electrolytes Li{sub x}La{sub 3}Zr{sub 2}O{sub 8.5+0.5x} (x = 7–9) have 1.32–3.49 wt.% Li{sub 2}CO{sub 3}. • The composition with x = 9 has high total conductivity, 7.5 × 10{sup −6} S cm{sup −1}, at room temperature. - Abstract: Samples of Li{sub x}La{sub 3}Zr{sub 2}O{sub 8.5+0.5x} (x = 6, 7, 8, 9, 10) were synthesized with the citrate–nitrate method. Neutron diffraction studies have shown the presence of lithium carbonate impurities in the synthesized compounds. We propose a simple and effective method to determine the carbonate impurity content in the solid electrolytes. The technique is based on the measurement of the carbon dioxide volume produced from the interaction of the investigated material with acid. Determined in this way, the content of Li{sub 2}CO{sub 3} in the synthesized electrolytes Li{sub 7}La{sub 3}Zr{sub 2}O{sub 12}, Li{sub 8}La{sub 3}Zr{sub 2}O{sub 12.5} and Li{sub 9}La{sub 3}Zr{sub 2}O{sub 13} are 1.32 ± 0.04, 1.95 ± 0.06 and 3.49 ± 0.10 wt.%, respectively. From the obtained data, the actual lithium content per formula unit of complex oxide was calculated for the synthesized compounds. The composition with x = 9 had the highest total conductivity, σ = 7.5 × 10{sup −6} S cm{sup −1}, at room temperature. All the investigated electrolytes have an activation energy of approximately 50 kJ mol{sup −1}.

36 MATERIALS SCIENCE↗

EVALUATION OF BALLISTIC DAMAGE IN AN ENCAPSULATED CERAMIC PANEL VIA X-RAY COMPUTED TOMOGRAPHY

X-ray computed tomography (XCT) is an important non-destructive evaluation technique for revealing the spatial distribution of ballistically-induced damage in ceramics. The level of detection and resolution of damage depends on the size of the sample and the parameters of the XCT approach (e.g., focal spot size, magnification, etc.). Previous and ongoing work in this area includes assessment of ballistically induced damage in both individual ceramic targets and ceramic armor panels. Ballistic damage in an encapsulated ceramic armor panel with a metal backing has been scanned and extensively evaluated using XCT 2-D and 3-D analysis. The purpose of using XCT evaluation in this study was to better characterize and understand all of the detectable damage. This information can be used to correlate damage features and types with the physical processes of damage initiation and growth. XCT scans and analyses of damage in the panel will be shown and discussed. This will include virtual 3-D solid visualizations and some quantitative analysis of damage features.

36 MATERIALS SCIENCE↗

Transitions in Wetting Behavior Between Liquid Ag-CuO Alloys and Al2O3Substrates

Reactive air brazing (RAB) is a method for joining ceramics with applications in high temperature technologies such as gas separation and solid oxide fuel cell (SOFC) components. An understanding of wetting behavior is critical for optimization of the brazing process. In the current study, the wetting behavior of Ag-CuO on Al2O3 was evaluated. Based on in-situ contact angle measurements, three regions of wetting behavior were identified in the composition range of 0 to 40 mol% CuO. The first transition, a 20° decrease between 2 mol% CuO and 4 mol% CuO, was attributed to the liquid composition miscibility gap, and the second, a 10° decrease between 10 mol% CuO and 20 mol% CuO, was hypothesized to be dominated by the formation of a reaction product. Small, discontinuous reaction regions were identified via electron probe microanalysis (EPMA) but could not be verified with X-ray photoelectron spectroscopy analysis (XPS).

air brazing↗

Microstructure and Electrical Transport Properties of Bi{sub 3}TiNbO{sub 9} High-Temperature Piezoceramics

High-density ceramic samples of the Bi{sub 3}TiNbO{sub 9} ferroelectric phase with a layered perovskite-like structure have been produced by tape casting slurry technology and hot pressing processes. The samples have been characterized by X-ray diffraction and dielectric, piezoelectric, and pyroelectric measurements. The results demonstrate that the samples have a well-defined texture due to the preferential orientation of the basal planes of their platelike grains across the pressing axis or along the film casting direction. The Curie temperature of the samples has been determined to be T{sub C} = 1180 K. The samples have anisotropic electrical transport characteristics. Their piezoelectric constants d{sub 33} in directions perpendicular and parallel to the texture plane is 22 and 5 pC/N, respectively. The conclusion has been drawn that the synthesized materials are potentially attractive for producing high-temperature piezoelectric elements.

36 MATERIALS SCIENCE↗

Energy Recovery System

Cogeneration system is one in which the energy ordinarily wasted in an industrial process is recovered and reused to create a second form of energy. Such an energy recovery system is in use at Crane Company's plant in Ferguson, KY, which manufactures ceramic bathroom fixtures. Crane's system captures hot stack gases from the company's four ceramic kilns and uses them to produce electrical power for plant operations.

Source record↗

Potentiometric Sensor for Real-Time Remote Surveillance of Actinides in Molten Salts

A potentiometric sensor is being developed at the Idaho National Laboratory for real-time remote surveillance of actinides during electrorefining of spent nuclear fuel. During electrorefining, fuel in metallic form is oxidized at the anode while refined uranium metal is reduced at the cathode in a high temperature electrochemical cell containing LiCl-KCl-UCl3 electrolyte. Actinides present in the fuel chemically react with UCl3 and form stable metal chlorides that accumulate in the electrolyte. This sensor will be used for process control and safeguarding of activities in the electrorefiner by monitoring the concentrations of actinides in the electrolyte. The work presented focuses on developing a solid-state cation conducting ceramic sensor for detecting varying concentrations of trivalent actinide metal cations in eutectic LiCl-KCl molten salt. To understand the basic mechanisms for actinide sensor applications in molten salts, gadolinium was used as a surrogate for actinides. The ß?-Al2O3 was selected as the solid-state electrolyte for sensor fabrication based on cationic conductivity and other factors. In the present work Gd3+-ß?-Al2O3 was prepared by ion exchange reactions between trivalent Gd3+ from GdCl3 and K+-, Na+-, and Sr2+-ß?-Al2O3 precursors. Scanning electron microscopy (SEM) was used for characterization of Gd3+-ß?-Al2O3 samples. Microfocus X-ray Diffraction (µ-XRD) was used in conjunction with SEM energy dispersive X-ray spectroscopy (EDS) to identify phase content and elemental composition. The Gd3+-ß?-Al2O3 materials were tested for mechanical and chemical stability by exposing them to molten LiCl-KCl based salts. The effect of annealing on the exchanged material was studied to determine improvements in material integrity post ion exchange. The stability of the ß?-Al2O3 phase after annealing was verified by µ-XRD. Preliminary sensor tests with different assembly designs will also be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Determination of Natural Beryllium (Be) in Soil and Swipe Samples Utilizing Yttrium/Beryllium Ratio

1. Objective: A method to determine whether beryllium (Be) components in surface swipe samples are from a natural source is needed. 2. Methods: Soil samples and surface swipes from area facilities were analyzed for marker elements to identify source pathways for beryllium (Be). To be useful, the natural marker element must be present at reasonably consistent levels across the site, must correlate with the Be concentration, and not have the potential to be present from non-natural sources. 3. Results: The research on marker elements used to identify source pathways for beryllium (Be) concentrations demonstrates a clear correlation between Be and yttrium (Y) in natural soils on the Nevada National Security Site. The Y/Be ratio is proposed as a method to characterize the source of Be in soil and surface swipe samples and to aid in recommendations for follow up actions. Swipe samples are analyzed using an ICP/MS method and compared with results from soil samples. Natural soil constituent levels and the Y/Be Ratio range is determined for the occupied and historical facilities and surrounding areas. Y/Be ratios within the statistical range established indicate the Be is from a natural source. Y/Be ratios lower than this range indicate the presence of another Be source, and may then be correlated to alloy, ceramic, or other operational sources by the ratios of copper, nickel, cobalt, uranium, and/or niobium. Example case studies of evaluations of buildings with historical operational beryllium usage, current ongoing technical processes, and heavy equipment used in large building demolitions are included demonstrating the value of the ratio approach. 4. Conclusions: This differentiation is valuable as there is no known correlation between natural beryllium in soil and beryllium disease.

54 ENVIRONMENTAL SCIENCES↗

Maturing ceramic am and establishing a qualification framework at los alamos national laboratory

We successfully produced specimens made from porcelain resin (Tethon3D) in three different orientations (Z=45mm, Z=4mm and Z=3mm) without any cracks or delamination, both before and after post-processing. Four-point flexural tests were conducted on these specimens. Among the three orientations, specimens printed in the Z=4mm direction showed the best flexural strength, followed by Z=3mm and Z=45mm.

36 MATERIALS SCIENCE↗

Development of metallization process: FSA project, cell and module formation research area

This experiment is involved in determining bulk resistivity values for different past concentrations. Experiments were performed on silicon Cz and non-Cz wafers. To determine bulk resistivity more accurately, pastes were printed on ceramic substrates. Contact resistance was determined by measuring the voltage drop at constant current. Because of irregularity of grid profiles, accurate determination of cross sections of grid lines is difficult. The bulk resistivity is accurate when the resistivity of the metallization is much less than that of the layer beneath it. When the resistivity of the metal approaches that of the substrate, the actual resistivity will be larger than the measured value.

Garcia, A., III↗

Microgravity processing of particulate reinforced metal matrix composites

The elimination of such gravity-related effects as buoyancy-driven sedimentation can yield more homogeneous microstructures in composite materials whose individual constituents have widely differing densities. A comparison of composite samples consisting of particulate ceramics in a nickel aluminide matrix solidified under gravity levels ranging from 0.01 to 1.8 G indicates that the G force normal to the growth direction plays a fundamental role in determining the distribution of the reinforcement in the matrix. Composites with extremely uniform microstructures can be produced by these methods.

Morel, Donald E.↗