Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

The Fabrication of All-Solid-State Lithium-Ion Batteries via Spark Plasma Sintering

Spark plasma sintering (SPS) has been successfully used to produce all-solid-state lithium-ion batteries (ASSLibs). Both regular and functionally graded electrodes are implemented into novel three-layer and five-layer battery designs together with solid-state composite electrolyte. The electrical capacities and the conductivities of the SPS-processed ASSLibs are evaluated using the galvanostatic charge-discharge test. Experimental results have shown that, compared to the three-layer battery, the five-layer battery is able to improve energy and power densities. Scanning electron microscopy (SEM) is employed to examine the microstructures of the batteries especially at the electrode–electrolyte interfaces. It reveals that the functionally graded structure can eliminate the delamination effect at the electrode–electrolyte interface and, therefore, retains better performance.

25 ENERGY STORAGE↗

Tritium Transport Modeling at the Pore Scale in Ceramic Breeder Materials Using TMAP8

Fusion reactors depend on the blanket material to breed and release tritium at the same rate or faster than it is consumed by the fusion reaction. Cellular ceramic breeders (CCBs) are dense materials that can maintain a high tritium breeding ratio while promoting tritium release because of highly connected pores. Assessing the tritium breeding capabilities of these materials requires a combination of extensive experimental and modeling efforts. In this work, we develop and calibrate a multiphysics model of tritium transport. This novel model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. We perform a sensitivity analysis and calibrate the model by comparing its predictions against experimental measurements of deuterium absorption. The calibrated model is then used to model tritium absorption in samples with different pore microstructures to investigate the effect of pore interconnectivity on tritium absorption. The model is part of the development of the multiscale, multiphysics framework for tritium transport [i.e., the Tritium Migration Analysis Program (TMAP8)], which is itself built on top of the finite-element multiphysics framework multiphysics object-oriented simulation environment (MOOSE). This study demonstrates some of TMAP8’s capabilities and is the first step toward assessing the tritium breeding capabilities of ceramic breeder material designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

X-ray Micro-Computed Tomography for Structural Analysis of All-Solid-State Battery at Pouch Cell Level

Characterizing the microstructure of all-solid-state batteries (ASSBs) during fabrication and operation is vital for their advancement, particularly as scaling to pouch cell levels introduces challenges in probing large-scale microstructural evolution. This work highlights the potential of synchrotron X-ray micro-computed tomography (sXCT) as a nondestructive, rapid (<30 min), and high-resolution technique for visualizing and quantifying key microstructural features, including overhang, porosity, contact loss, active surface area, and tortuosity, in all-solid-state pouch cells. The large field of view (up to millimeters) of sXCT enables detailed analysis at an industry-relevant scale, bridging the gap between laboratory research and commercial applications. Furthermore, integrating realistic sXCT-derived 3D models into multiphysics simulations could provide insights into chemo-mechanical degradation, particularly at the edges of the pouch cells, offering a pathway for designing robust, high-performance ASSBs. This perspective establishes sXCT as an indispensable tool for advancing both the understanding and the engineering of next-generation energy storage systems.

25 ENERGY STORAGE↗

Computational Design and Discovery of Ni-Based Alloys and Coatings: Thermodynamic Approaches Validated by Experiments

This project developed computational tools that can complement and support experimental efforts in order to enable discovery and more efficient development of Ni-base structural materials and coatings. The project goal was reached through an integrated computation-predictive and experimental-validation approach, including first-principles calculations, thermodynamic CALPHAD (CALculation of PHAse Diagram), and experimental investigations on compositions relevant to Ni-base superalloys and coatings in terms of oxide layer growth and microstructure stabilities. The developed description included composition ranges typical for coating alloys and, hence, allow for prediction of thermodynamic properties for these material systems. The calculation of phase compositions, phase fraction, and phase stabilities, which are directly related to properties such as ductility and strength, was a valuable contribution, along with the collection of computational tools that are required to meet the increasing demands for strong, ductile and environmentally-protective coatings. Specifically, a suitable thermodynamic description for the Ni-Al-Cr-Co-Si-Hf-Y system was developed for bulk alloy and coating compositions. Experiments were performed to validate and refine the thermodynamics from the CALPHAD modeling approach. Additionally, alloys produced using predictions from the current computational models were studied in terms of their oxidation performance. Finally, results obtained from experiments aided in the development of a thermodynamic modeling automation tool called ESPEI/pycalphad - for more rapid discovery and development of new materials.

36 MATERIALS SCIENCE↗

Multi-scale simulation of reaction, transport and deactivation in a SBA-16 supported catalyst for the conversion of ethanol to butadiene

Effective design of heterogeneous catalytic systems requires careful coordination of physiochemical phenomena that span orders or magnitude in length and time scales. Multiscale modelling and simulation tools can provide useful insight for understanding and improving the performance of such systems. Mesoporous silica catalyst support materials present a versatile platform wherein support attributes may be tuned to control transport phenomena throughout the system. In this study we develop an integrated multiscale modelling approach for the conversion of ethanol to butadiene over a SBA-16 mesoporous silica supported catalyst. We use molecular dynamics simulations to calculate domain specific diffusivities of reactants and products in the various domains of SBA-16's nanostructure. This is used to calculate a resultant effective diffusivity through its microstructure using finite element method (FEM) models of the tessellated unit cell. The resultant intraparticle effective diffusivity enables the development of a reduced-order reactor level FEM model that is able to implicitly account for the SBA-16's transport effects without the explicit consideration of its detailed geometry. Experimental bench-scale conversion data for the ethanol to butadiene process over SBA-16 is used to extract intrinsic kinetic rate constants for a simplified reaction mechanism using this reduced order bench-scale reactor FEM model. The model is able to reproduce experimental trends in conversion and activity lifetimes. The impact of varying key support attributes such as pore-size and particle size on catalytic activity lifetimes is then explored. We demonstrate the utility of this multi-scale modelling strategy in guiding catalyst design for the development of rational strategies to improve the performance of heterogeneous supported catalytic systems.

09 BIOMASS FUELS↗

Self‐Assembly of 0D/3D Perovskite Bi‐Layer from a Micro‐Emulsion Ink

Abstract 2D/3D bilayer perovskite synthesized using sequential deposition methods has shown effectiveness in enhancing the stability of perovskite solar devices. However, these approaches present several limitations such as uncontrolled chemical processes, disordered interfacial states, and microscale heterogeneities that can chemically, structurally, and electronically compromise the performance of solar modules. Here, this work demonstrates an emulsion‐based self‐assembly approach using natural lipid biomolecules in a nonionic solution system to form a 0D/3D bilayer structure. The new capping layer is composed of 0D‐entity nanoparticles of perovskite encapsulated by a hydrophobic lipid membrane, analogous to a cell structure, formed through a molecular self‐assembly process. This 0D layer provides a strong water repellent characteristics, optimum interface microstructure, and excellent homogeneity that drives significant enhancement in stability. Solar modules with a large active area of 70 cm 2 fabricated using films comprising of 0D/3D bilayer structure are found to show consistent efficiency of >19% for 2800 h of continuous illumination in the air (60% relative humidity). This emulsion‐based self‐assembly approach is expected to have a transformative impact on the design and development of stable perovskite‐based devices.

0D/3D bilayers↗

Novel pore size-controlled, susceptibility matched, 3D-printed MRI phantoms

We report the design concept and fabrication of MRI phantoms, containing blocks of aligned microcapillaires that can be stacked into larger arrays to construct diameter distribution phantoms or fractured, to create a “powder-averaged” emulsion of randomly oriented blocks for vetting or calibrating advanced MRI methods, that is, diffusion tensor imaging, AxCaliber MRI, MAP-MRI, and multiple pulsed field gradient or double diffusion-encoded microstructure imaging methods. The goal was to create a susceptibility-matched microscopically anisotropic but macroscopically isotropic phantom with a ground truth diameter that could be used to vet advanced diffusion methods for diameter determination in fibrous tissues. Two-photon polymerization, a novel three-dimensional printing method is used to fabricate blocks of capillaries. Double diffusion encoding methods were employed and analyzed to estimate the expected MRI diameter. Susceptibility-matched microcapillary blocks or modules that can be assembled into large-scale MRI phantoms have been fabricated and measured using advanced diffusion methods, resulting in microscopic anisotropy and random orientation. This phantom can vet and calibrate various advanced MRI methods and multiple pulsed field gradient or diffusion-encoded microstructure imaging methods. We demonstrated that two double diffusion encoding methods underestimated the ground truth diameter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Rapid discovery of high hardness multi-principal-element alloys using a generative adversarial network model

Multi-principal element alloys (MPEAs) continue to gain research prominence due to their promising high-temperature microstructural and mechanical properties. Recently, machine learning (ML) and materials informatics have been used extensively for screening MPEAs, however, most of these efforts were focused on constructing classification and regression models for predicting phase stability and mechanical properties of known compositions. These approaches may accelerate the screening process but optimizing new compositions with desirable properties within a practical time frame from an infinitely large design space of MPEA systems remains a grand challenge. To tackle this composition optimization challenge, a generative adversarial network coupled with a neural-network ML model was utilized to design MPEAs by filtering compositions that have high hardness. Even in a high-dimensional space with 18 elements as descriptors, the ML model was able to generate optimized compositions from which one composition was found to have 10% higher hardness (941 HV) than the maximum in the training data (857 HV). Density-functional theory was used to provide thermodynamic and electronic insights to higher hardness of the new MPEA found. The present work can optimize compositions from a wide design space of 18 elements (including W, Ta and Nb) that presents an opportunity to synthesize new compositions for applications ranging from corrosion-resistant alloys to nuclear materials. Here the findings suggest that generative ML can greatly accelerate materials discovery by identifying novel compositions, which can serve as a data-informed tool to guide experiments.

36 MATERIALS SCIENCE↗

Light-Controlled Hierarchical Self-Assembly of Polyelectrolytes and Supramolecular Polymers

Dynamic control over supramolecular interactions using various stimuli continues to drive the development of smart materials. In this paper, we describe the extension of dynamic self-assembly to a self-assembled hierarchical structure. A peptide amphiphile (PA) was designed with a photocleavable nitrobenzyl ester component such that it would undergo a sphere-to-cylinder transition upon irradiation, as confirmed by cryogenic transmission electron microscopy and small-angle X-ray scattering (SAXS). The photocleavable PA was then tested in the formation of a macroscopic sac made through a complex hierarchical self-assembly process between PA and hyaluronic acid. The microstructure of the resulting sac has previously been noted to depend dramatically on the geometry of the PA nanostructure. Photolysis of the PA solution during sac formation led to a sac microstructure that displayed characteristics of sacs made with both cylinder-forming PAs and sphere-forming PAs, as measured by scanning electron microscopy and SAXS.

36 MATERIALS SCIENCE↗

Phase-field predictions of the influence of cooling rates during AM on the Evolution of Microstructures in Nickel-Based Single Crystal Superalloys

Additive manufacturing of single crystals made of Ni-based superalloys offers major cost savings for gas turbine engines with the inclusion of internal cooling channels. However, the lack of understanding of the effect of transient thermal conditions on solidification grain structure during additive manufacturing hinders the potential for process control to maintain the single crystal quality. The use of high-fidelity simulations through high performance computing to predict the evolution of the solidification microstructure will enhance the abilities to tailor the microstructures through process optimization. Phase field simulations are used to determine the effect local thermal conditions and defects on the stability of the solidification morphology, specifically with respect to the onset of columnar-to-equiaxed transition that results in the loss of the single crystal. The results are expected to be instrumental for developing future surrogate models to speed up the integration of design and manufacturing of turbine blades under the harsh in-service conditions.

36 MATERIALS SCIENCE↗

Topology and layout optimization of discrete and continuum structures

The basic features of the ground structure method for truss structure an continuum problems are described. Problems with a large number of potential structural elements are considered using the compliance of the structure as the objective function. The design problem is the minimization of compliance for a given structural weight, and the design variables for truss problems are the cross-sectional areas of the individual truss members, while for continuum problems they are the variable densities of material in each of the elements of the FEM discretization. It is shown how homogenization theory can be applied to provide a relation between material density and the effective material properties of a periodic medium with a known microstructure of material and voids.

Bendsoe, Martin P.↗

Advanced Characterization Capabilities for Nuclear Materials via Nuclear Science User Facilities (NSUF)

Advanced post-irradiation examination (PIE) techniques are required to design new or improved nuclear materials, characterize, and understand in-core behavior of fuel and materials, and support the qualification of new reactor materials. The Nuclear Science User Facilities (NSUF) is the U.S. Department of Energy Office of Nuclear Energy's only designated nuclear science user facility. NSUF provides researchers access to PIE capabilities at Idaho National Laboratory and at a diverse mix of university, national laboratory and industrial partner institutions. The PIE capabilities include novel destructive and non-destructive techniques for radiation damage characterization, such as advanced diffraction techniques (X-ray, electron, or neutron) coupled to extreme environments; in-situ observation of microstructural evolution under irradiation; in-situ irradiation to monitor corrosive attack in coolant environments; in-situ irradiation and mechanical testing; and test methods for synergistic effects of superimposed extreme environments (temperature, irradiation, stress, corrosion) on materials behaviors. This talk will provide an overview of NSUF PIE capabilities.

36 MATERIALS SCIENCE↗

Effect of Silica and Mixing Time on Microstructures of Porous Polymer Composite by Emulsion Templating

Porous polymer composite with tailored porosity is applied in the myriads of areas such as energy storage, oil/water absorption, bioengineering, and advanced areas of material science. The emulsion templating technology is one of the most popular methods for synthesizing porous polymer composite. It involves solidifying a two-phase mixture of porogen and polymer, then removing porogen to create pores within the continuous emulsion phase by polymerization or curing. The surfactant plays a pivotal role in accomplishing a stable emulsion, a key factor in designing the internal porous structure. This study highlights the effect of silica filler and mixing time on pore morphology, i.e., shape, size, and distribution. on polydimethylsiloxane (PDMS) porous structure utilizing the water-in-oil emulsion templating method. Span® 80 is used as a surfactant to reduce the surface tension between water, silica, and PDMS and simultaneously create a strong foaming effect. Different weight concentrations of silica (1-10 wt%) were chosen while keeping the internal phase, i.e., water (50 wt%) constant. The designed porous structures were further characterized through scanning electron microscopy (SEM). Porous composite specimens fabricated with higher silica content and mixing time consistently exhibit smaller pore sizes than specimens fabricated with lower mixing time and silica content. A breakthrough of pore morphology is seen at silica content higher than 5wt% at 1 min mixing, however, pore morphology drastically changes when mixing time increases from 1 min to 6 min. Variation of finer mixing time beyond 1 min shows stepwise changes in pore morphology from a large single-phase porous structure to a bi-modal porous structure which eventually become a smaller single-mode porous structure. Thus, the emulsion templating technique, in combination with different filler content and mixing time, will effectively aid in designing engineered porous polymer composite with varying stiffness and pore morphology.

Porous polymer, Emulsion templating, Surfactant, P↗

All-alumina quarter-wave plate coatings fabricated by glancing angle deposition using serial bideposition

Anisotropic phase retarders, used in high power laser facilities to perform polarization smoothing, can be obtained by the glancing angle deposition (GLAD) coating process. Due to its high laser resistance, the coatings are mainly made of silica. Therefore, limited attention has been given to other dielectric materials. Here we present a study on alumina GLAD anisotropic coatings; a material with high laser resistance, higher birefringence and lower environmental sensitivity than silica. Since the anisotropy is related to the coatings microstructure through the deposition angle, samples were coated at angles varying from ± 68° to ± 82° using the serial bideposition technique. They were characterized by ellipsometry, polarimetry, spectrophotometry and electron microscopy. We showed that the highest birefringence is obtained at a deposition angle of ± 76° with an in-plane value of 0.053. Based on these results, a quarter-wave plate at 351 nm was designed as a multilayer with seven pairs of anisotropic layers deposited at ± 76° and isotropic layers deposited at 0°. The fabricated coating exhibited a uniform retardance of 88.51 ± 0.45 nm. The alumina GLAD wave plates presented here, open the door to new possibilities in the laser field and especially in the field of fusion energy.

36 MATERIALS SCIENCE↗

High-Entropy Alloys for Accelerator Beam Window Applications

Development of novel high-entropy alloys (HEAs) is currently underway for potential use as beam windows in future multi-megawatt target systems at Fermilab. HEAs encompass a new class of materials with a vast design space allowing for material properties to be tailored for particular applications and to potentially offer improved resistance to beam-induced radiation damage and thermal shock effects. The alloy systems being studied consist of several compositions of AlCoCrMnTiV with 4 6 component elements. These alloys are all predicted by CALPHAD simulation to have a single-phase BCC crystal structure and low density, with some compositions displaying ordered, nanoscale precipitates. This presentation will briefly discuss alloy design and synthesis before giving a detailed description of the characterization studies of these HEAs in both the pristine state and post-irradiation by low-energy heavy ions to high damage levels. Electron microscopy techniques to quantify elemental homogeneity and composition, determine grain size, shape, and orientation, and quantify lattice parameters, defect structures and precipitate phases are all being used to study alloy microstructures. Mechanical properties of the alloys at the microscale will be reported. The evolution of these properties as a function of radiation damage will also be described. Bulk thermal characteristics of these HEAs have been tested to measure specific heat capacity and coefficient of thermal expansion as a function of temperature. To determine bulk tensile properties a miniature tensile testing apparatus is under development; it s commissioning will be covered briefly. The talk will conclude with our plans for alloy down-selection.

Burleigh, A. [Fermilab]↗

Investigation of the Formation of Topologically Close Packed Phase Instabilities in Nickel-Based Superalloy Rene N6

Topologically close packed (TCP) phase instability in third generation Ni-base superalloys is understood to hinder component performance when used in high-temperature jet engine applications. The detrimental effects on high temperature performance from these brittle phases includes weakening of the Ni-rich matrix through the depletion of potent solid solution strengthening elements. Thirty-four compositional variations of polycrystalline Rene N6 were defined from a design-of-experiments approach and then cast, homogenized, and finally aged to promote TCP formation. Our prior work reported on the results of the multiple retression modeling of these alloys in order to predict the volume fraction of TCP. This paper will present further regression modeling results on these alloys in order to predict the occurrence of TCP in third generation Ni-base superalloy microstructures. Kinetic results are also discussed.

Ritzert, Frank↗

Additive Manufactured Materials Studies

The production of additively manufactured (AM) materials, is a growing technology that potentially offers more cost effective ways to produce metallic components for various uses. Mechanical properties of some AM metals have been studied, but more work is needed to better understand their dynamic properties as a function of orientation. Due to the melting and reheating of molten metal during fabrication, these materials tend to have internal porosity and slightly different microstructures along the weldments and normal to the weldments that may cause the materials to behave differently than their forged counterparts. The AM process builds up a part layer by layer, which provides opportunities to tailor geometry and optimize structural performance in addition to minimizing the amount of material waste for oddly shaped parts, thereby reducing cost. These advanced materials hold great promise for revolutionizing design, fabrication, and assembly of engineered components and could be used for many NNSA-specific applications including armoring complex elements of nuclear weapons, and customized diagnostic components in subcritical experiments. We have conducted materials studies in collaboration with the University of Nevada, Las Vegas (UNLV) as well as Los Alamos National Laboratory (LANL) under our Site-Directed Research and Development program and the Nevada Science Initiative. We are currently placing emphasis on quantifying how dynamic properties are affected by directionality and porosity of the material. A study of dynamic failure events in forged, layered, and additive manufactured (AM) titanium alloy subject to hypervelocity impact was conducted in collaboration with UNLV. Experiments were conducted using a two stage light-gas gun, 0.22-caliber Lexan projectiles, and different types of titanium target plates. A four-channel Photonic Doppler Velocimetry (PDV) system was used to study the free surface velocities to provide an understanding of the different failure mechanisms in these materials. The experimental measurements were used to validate computational simulations, which describe the behavior of these materials under shock. It was determined that AM, forged titanium, and multi-layered stacks produce similar velocity profiles during the early stage of impact, with the AM targets exhibiting spall at lower velocities and the multi-layered stacks exhibiting vibrations between plates. Simulations of solid and layered forged materials provide a good match to experimental data.

36 MATERIALS SCIENCE↗