Search NASA⌕ Search

SEARCH · Search NASA

Results for “BASE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Passive Acoustic Detection of Wind Turbine In-Flow Conditions for Active Control and Optimization

Wind is a significant source of energy; however, the human capability to produce electrical energy still has many hurdles to overcome. One of these is the unpredictability of the winds in the atmospheric boundary layer (ABL). The ABL is highly turbulent in both stable and unstable conditions (based on the vertical temperature profile) and the resulting fluctuations can have a dramatic impact on wind turbine operation. Any method by which these fluctuations could be observed, estimated, or predicted could provide a benefit to the wind energy industry as a whole. Based on the fundamental coupling of velocity fluctuations to pressure fluctuations in the nearly incompressible flow in the ABL, This work hypothesizes that a ground-based array of infrasonic pressure transducers could be employed to estimate the vertical wind profile over a height relevant for wind turbines. To analyze this hypothesis, experiments and field deployments were conducted. Wind tunnel experiments were performed for a thick turbulent boundary layer over a neutral or heated surface. Surface pressure and velocity probe measurements were acquired simultaneously. Two field deployments yielded surface pressure data from a 49 element array. The second deployment at the Reese Technology Center in Lubbock, TX, also included data from a smaller aperture, 96-element array and a 200-meter tall meteorological tower. Analysis of the data successfully demonstrated the ability to estimate the vertical velocity profile using coherence data from the pressure array. Also, dynamical systems analysis methods were successful in identifying and tracking a gust type event. In addition to the passive acoustic profiling method, this program also investigated a rapid response Doppler SODAR system, the optimization of wind turbine blades for enhanced power with reduced aeroacoustic noise production, and the implementation of a wireless health monitoring system for the wind turbine blades. Each of these other objectives was met successfully. The use of phase unwrapping applied to SODAR data was found to yield reasonable results for per-pulse measurements. A health monitoring system design analysis was able to demonstrate the ability to use a very small number of sensors to monitor blade health based on the blade's overall structural modes. Most notable was the development of a multi-objective optimization methodology that successfully yielded an aerodynamic blade design that produces greater power output with reduced aerodynamic loading noise. This optimization method could be significant for future design work.

17 WIND ENERGY↗

Investigation of the influence of frictional viscosity regularization on quasi-static gas-solid flow predictions in a conical spouted bed with non-porous draft tube

The stress in the quasi-static particle flow is often modeled through the Mohr-Coulomb failure criterion. In the extension to complex three-dimensional flows, a granular viscosity is introduced through a tensorial rheology and the deviatoric frictional stress tensor is assumed aligned with the strain rate tensor. This granular viscosity is singular as the shear rate approaches zero, regardless of the local rheology. We discuss the influence of regularizing such a frictional viscosity on the particle circulation rate and other measured characteristics in a laboratory scale draft tube spouted bed. Here, the friction between particles is modeled either with a constant Coulomb rheology or using a local particle pressure and strain-rate based friction known as μ ( I )-rheology. The predictions appear very dependent on the regularization parameter introduced by the method. The mean properties of the flow (e.g. circulation and pressure drop) monotonically converge towards the measurements when the regularization parameter tends to zero. In other respects, the two regularization models regarded in this study induced similar hydrodynamics within the spouted bed of interest. But the analysis of the conditional averages of the inertial number and the fraction of the solids in the quasi-static regime shows that the extent and staticity of the quasi-static region is sensitive to changes to the regularization parameter or regularization function.

36 MATERIALS SCIENCE↗

A shock tube study of ignition delay times in diluted methane, ethylene, propene and their blends at elevated pressures

Ignition delay times (IDT) of small hydrocarbons at elevated pressures provide a valuable constraint for the refinement of the core small-hydrocarbon sub-mechanisms used in all combustion kinetics. Current knowledge of these core mechanisms is based largely on low-pressure data, with only limited high-pressure data available. To remedy this, here the present study focuses on ignition delay times in methane, ethylene, propene and their blends at elevated pressures. IDT measurements were performed in 4% O 2 , balance Ar mixtures, over the temperature range of 950–1800 K, at pressures of 14–60 atm and equivalence ratios of 1 and 2. IDT was determined from recorded sidewall pressure, OH* emission measurements and fuel time-histories measured using laser absorption at 3.39 μm. These measurements extend the test conditions of earlier studies, with the advantage that they have all been performed at similar conditions and with the same facility and should provide a uniform set of kinetics targets for the evaluation of core small-hydrocarbon mechanisms. This dataset also allowed the temperature variation of the pressure and equivalence ratio scaling for methane and ethylene IDT to be investigated.

42 ENGINEERING↗

Cubic boron nitride as a primary calibrant for a high temperature pressure scale

We present results establishing a new high pressure scale at high temperature based on the thermal equation of state and elastic properties of cubic boron nitride (cBN). This scale is derived from simultaneous measurements of density and sound velocities at high pressure and temperature independent of any previous pressure scale. The present results obtained at room temperature to 27 GPa suggest the validity of the current ruby scale (within {+-}4% at 100 GPa). At high temperature, data obtained at 16 GPa to 723 K are in fair agreement with the thermal equation of state of cBN reported in our previous work. We have also shown that cBN can serve as a convenient pressure gauge in X-ray and optical studies using the laser heated diamond anvil cell.

36 MATERIALS SCIENCE↗

Elemental Surface Analysis at Ambient Pressure

The development of a portable surface elemental analysis tool based on the excitation of characteristics x-rays at ambient pressure with an electron beam is described.

atmospheric electron x-ray spectrometer XRF EDX ED↗

Noninvasive measurement of pulsatile intracranial pressure using ultrasound

The present study was designed to validate our noninvasive ultrasonic technique (pulse phase locked loop: PPLL) for measuring intracranial pressure (ICP) waveforms. The technique is based upon detecting skull movements which are known to occur in conjunction with altered intracranial pressure. In bench model studies, PPLL output was highly correlated with changes in the distance between a transducer and a reflecting target (R2 = 0.977). In cadaver studies, transcranial distance was measured while pulsations of ICP (amplitudes of zero to 10 mmHg) were generated by rhythmic injections of saline. Frequency analyses (fast Fourier transformation) clearly demonstrate the correspondence between the PPLL output and ICP pulse cycles. Although theoretically there is a slight possibility that changes in the PPLL output are caused by changes in the ultrasonic velocity of brain tissue, the decreased amplitudes of the PPLL output as the external compression of the head was increased indicates that the PPLL output represents substantial skull movement associated with altered ICP. In conclusion, the ultrasound device has sufficient sensitivity to detect transcranial pulsations which occur in association with the cardiac cycle. Our technique makes it possible to analyze ICP waveforms noninvasively and will be helpful for understanding intracranial compliance and cerebrovascular circulation.

NASA Center ARC↗

Deflagration Rate Measurements of Three Insensitive High Explosives: LLM-105, TATB, and DAAF

The pressure dependent deflagration rates of LLM-105, DAAF and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. One DAAF formulation, two different formulations of LLM-105, and four formulations of TATB were studied; results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating DAAF and TATB formulations causes the deflagration rate to accelerate. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparison of Corcos-based and experimentally-derived coherence factors for BFFs estimation

In this paper, high-spatial-resolution unsteady Pressure Sensitive Paint (uPSP) data are utilized to compare two methods for panel Buffet Forcing Functions (BFF) estimation for the Space Launch System (SLS). Such methods are based on discrete pressure measurements within a panel but employ coherence factors to account for partially-correlated fluctuating pressures across the whole panel. In one method, coherence factors are derived based on the Corcos model, whereas the second method utilizes experimentally-derived coherence factors. To simulate discrete measurements using uPSP data, suitable subsets of the data are extracted. When full uPSP resolution is retained, uPSP data provide a benchmark to assess discrete-measurements-based methods. The analysis focuses on the peak SLS buffet environment located downstream of the Forward Attachment Hardware (FAH) between the core stage and solid rocket boosters. Trends of Corcos-based and experimentally-derived coherence factors are in reasonable agreement with the benchmark. However, at certain frequencies, experimentally-derived coherence factors are sensitive to the separation distance between pressure measurements utilized to compute coherence lengths. Such sensitivity originates from deviation of the experimental-based coherence function from an exponential decay assumption. On the other hand, the present implementation of the Corcos model fails to capture certain non-turbulent boundary layer related environments, such as a subharmonic of FAH vortex-shedding. For all methods presented in this paper, at near transonic conditions, increased pressure coherence and spatial nonuniformity lead to BFF overestimation and sensitivity to the pressure measurement location within the panel.

transonic buffet↗

Equilibrium and non-equilibrium effects in high pressure phase transformations of carbon

The behavior of carbon in the range 1–100 GPa and 1–10 kK is central to problems in planetary interiors, inertial confinement fusion targets, and high-pressure synthesis of carbon-based materials, but experiments in this regime are difficult and often provide only indirect constraints on phase behavior. As a result, phase boundary loci, structure, and limits of metastability at high pressure remain uncertain. In this work, machine-learning enhanced atomistic simulations are used to address this knowledge gap. We determine the melt line up to 100 GPa, the graphite-diamond phase boundary up to the melt line, and analyze structure of the coexisting phases. We show that the coexisting liquid evolves smoothly with pressure without evidence for a first-order liquid–liquid transition. Orientation-resolved graphite melting simulations indicate that basal-plane interfaces develop a dewetting layer and undergo layer-by-layer melting, producing kinetic hysteresis and an apparent orientation dependence of the melt line. Non-equilibrium quenches from the melt are used to construct a kinetically limiting graphite–diamond phase boundary for rapid quenches from above the melt line, and show that graphite is metastable at pressures of up to ≈ 25 GPa. These results provide bounds on equilibrium and metastable behavior in carbon relevant for interpreting high-pressure experiments and for designing synthesis pathways to specific carbon microstructures.

Lyu, Yanjun [Department of Materials Science and E↗

Analytical Assessment of the Reciprocating Feed System

A preliminary analysis tool has been created in Microsoft Excel to determine deliverable payload mass, total system mass, and performance of spacecraft systems using various types of propellant feed systems. These mass estimates are conducted by inserting into the user interface the basic mission parameters (e.g., thrust, burn time, specific impulse, mixture ratio, etc.), system architecture (e.g., propulsion system type and characteristics, propellants, pressurization system type, etc.), and design properties (e.g., material properties, safety factors, etc.). Different propellant feed and pressurization systems are available for comparison in the program. This gives the user the ability to compare conventional pressure fed, reciprocating feed system (RFS), autogenous pressurization thrust augmentation (APTA RFS), and turbopump systems with the deliverable payload, inert mass, and total system mass being the primary comparison metrics. Analyses of several types of missions and spacecraft were conducted and it was found that the RFS offers a performance improvement, especially in terms of delivered payload, over conventional pressure fed systems. Furthermore, it is competitive with a turbopump system at low to moderate chamber pressures, up to approximately 1,500 psi. Various example cases estimating the system mass and deliverable payload of several types of spacecraft are presented that illustrate the potential system performance advantages of the RFS. In addition, a reliability assessment of the RFS was conducted, comparing it to simplified conventional pressure fed and turbopump systems, based on MIL-STD 756B; these results showed that the RFS offers higher reliability, and thus substantially longer periods between system refurbishment, than turbopump systems, and is competitive with conventional pressure fed systems. This is primarily the result of the intrinsic RFS fail-operational capability with three run tanks, since the system can operate with just two run tanks.

Eddleman, David E.↗

Pressure-Sensitive Paints Advance Rotorcraft Design Testing

The rotors of certain helicopters can spin at speeds as high as 500 revolutions per minute. As the blades slice through the air, they flex, moving into the wind and back out, experiencing pressure changes on the order of thousands of times a second and even higher. All of this makes acquiring a true understanding of rotorcraft aerodynamics a difficult task. A traditional means of acquiring aerodynamic data is to conduct wind tunnel tests using a vehicle model outfitted with pressure taps and other sensors. These sensors add significant costs to wind tunnel testing while only providing measurements at discrete locations on the model's surface. In addition, standard sensor solutions do not work for pulling data from a rotor in motion. "Typical static pressure instrumentation can't handle that," explains Neal Watkins, electronics engineer in Langley Research Center s Advanced Sensing and Optical Measurement Branch. "There are dynamic pressure taps, but your costs go up by a factor of five to ten if you use those. In addition, recovery of the pressure tap readings is accomplished through slip rings, which allow only a limited amount of sensors and can require significant maintenance throughout a typical rotor test." One alternative to sensor-based wind tunnel testing is pressure sensitive paint (PSP). A coating of a specialized paint containing luminescent material is applied to the model. When exposed to an LED or laser light source, the material glows. The glowing material tends to be reactive to oxygen, explains Watkins, which causes the glow to diminish. The more oxygen that is present (or the more air present, since oxygen exists in a fixed proportion in air), the less the painted surface glows. Imaged with a camera, the areas experiencing greater air pressure show up darker than areas of less pressure. "The paint allows for a global pressure map as opposed to specific points," says Watkins. With PSP, each pixel recorded by the camera becomes an optical pressure tap. "Instead of having 100 or 200 pressure taps, you can have in theory several million, up to whatever the resolution of your camera is." Watkins explains that typical wind tunnel testing requires two models: one with very little instrumentation, and a pressure model with a significant amount of sensors applied. "If you can make all of your measurements on one model with PSP, you've decreased your model costs by at least a factor of two and preferably your testing costs by about that much," he says. PSP technology has been around for almost 20 years, but a PSP solution for gathering instantaneous dynamic pressure data from surfaces moving at high speeds, such as rotor blades, was not available until a NASA partnership led to a game-changing innovation.

Source record↗

Deformation of binary and boron-doped Ni 3 Al alloys at high pressures studied with synchrotron x-ray diffraction

In situ x-ray synchrotron diffraction experiments were carried out on nickel-based high-strength superalloys under pressure to understand their deformation mechanism using a diamond anvil cell (DAC). Radial x-ray diffraction determines the room-temperature equations of state and yield strengths of binary Ni 3 Al alloy and 500 ppm boron-doped Ni 3 Al to pressures of 20 and 46 GPa, respectively. Crystallographic preferred orientations observed in these superalloys due to anisotropic stress field in DAC indicate the onset of plastic deformation. Inverse pole figure analysis reveals that the underlying deformation mechanisms change from an octahedral slip to a simultaneous activation of octahedral and cube slips upon doping with boron. The yield-strength values were found to increase with pressure and are comparable to those determined from axial diffraction experiments. The results indicate that the yield strength of Ni 3 Al:B is about 0.5 GPa higher (at pressures below 20 GPa) due to grain boundary strengthening by boron. It is shown that due to high elastic anisotropy of Ni 3 Al alloy, the yield-strength estimations from diffraction experiments strongly depend on the micromechanical model used to convert the measured elastic strains into stresses.

42 ENGINEERING↗

Lattice expansion and ligand twist during CO2 adsorption in flexible Cu bipyridine metal–organic frameworks

Flexible metal–organic frameworks (MOFs) can show exceptional selectivity and capacity for adsorption of CO 2 . The incorporation of CO 2 into flexible MOFs that have Cu 2+ coordination centers and organic pillar ligands is accompanied by a distortion of the framework lattice arising from chemical interactions between these components and CO 2 molecules. CO 2 adsorption yields a reproducible lattice expansion that is enabled by the rotation of the pillar ligands. The structures of Cu 2 (pzdc) 2 (bpy) and Cu 2 (pzdc) 2 (bpe), CPL-2 and CPL-5, were evaluated using in situ synchrotron X-ray powder diffraction at room temperature at CO 2 gas pressures up to 50 atm. The structural parameters exhibit hysteresis between pressurization and depressurization. The pore volume within CPL-2 and CPL-5 increases at elevated CO 2 pressure due to a combination of the pillar ligand rotation and the overall expansion of the lattice. Volumetric CO 2 adsorption measurements up to 50 atm reveal adsorption behavior consistent with the structural results, including a rapid uptake of CO 2 at low pressure, saturation above 20 atm, and hysteresis evident as a retention of CO 2 during depressurization. Finally, a significantly greater CO 2 uptake is observed in CPL-5 in comparison with predictions based on CO 2 pressure-induced expansion of the pore volume available for adsorption, indicating that the flexibility of the CPL structures is a key factor in enhancing adsorption capacity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transonic buffet behavior of Northrop F-5A aircraft

Flight tests were performed on an F-5A aircraft to investigate the dynamic buffet pressure distribution on the wing surfaces and the responses during a series of transonic maneuvers called wind-up turns. The conditions under which the tests were conducted are defined. The fluctuating buffet pressure data on the right wing of the aircraft were acquired by miniaturized semiconductor-type pressure transducers flush mounted on the wing. Processing of the fluctuating pressures and responses included the generation of the auto- and cross-power spectra, and of the spatial correlation functions. An analytical correlation procedure was introduced to compute the aircraft response spectra based on the measured buffet pressures.

Hwang, C.↗

Degradation of the lunar vacuum by a moon base

Several industrial processes requiring high and ultra-high vacuum similar to the lunar vacuum are outlined. The effects of a 20-person lunar base and a 250-person industrial facility on this vacuum are discussed. It is shown that exhaust from transport spacecraft and leakage from the habitat will be comparable to the daytime gas pressure for the 20-person base, and will degrade the vacuum to the range of 2 x 10 to the -9th torr for the use of 250-person facility. This will result in replacing the mostly nonreactive gases hydrogen, helium, and neon with more reactive gases containing carbon and oxygen. This vacuum is still good enough to perform many important vacuum processes such as plasma-deposition of amorphous silicon for solar cells, but processes such as molecular beam epitaxy or locating an intersecting beam accelerator on the moon will require additional vacuum pumping.

Landis, Geoffrey↗

New Possible Structure of Silicide Mg{sub 2}Si under Pressure

As a result of an evolutionary search based on the density functional theory, a new low-symmetry structure of silicide Mg{sub 2}Si under pressure was discovered. This structure can exist along with the known structures of the symmetry Pnma and P63/mmc and is stable at a pressure of about 20 GPa. The lattice parameters of the discovered structure are in better agreement with the experimental values than the lattice parameters of the known structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stochastic Estimation and Non-Linear Wall-Pressure Sources in a Separating/Reattaching Flow

Simultaneous wall-pressure and PIV measurements are used to study the conditional flow field associated with surface-pressure generation in a separating/reattaching flow established over a fence-with-splitter-plate geometry. The conditional flow field is captured using linear and quadratic stochastic estimation based on the occurrence of positive and negative pressure events in the vicinity of the mean reattachment location. The results shed light on the dominant flow structures associated with significant wall-pressure generation. Furthermore, analysis based on the individual terms in the stochastic estimation expansion shows that both the linear and non-linear flow sources of the coherent (conditional) velocity field are equally important contributors to the generation of the conditional surface pressure.

Naguib, A.↗

Validation of a Cephalad Fluid Shift Countermeasure

INTRODUCTION: This project will provide critical data required to objectively determine how an optimized thigh cuff could be incorporated into the NASA integrated physiological countermeasure suite. This project will determine if thigh cuffs used during simulated spaceflight impact intracranial pressure (ICP), ocular structure and function, and intraocular pressure (IOP) using state of-the-art techniques. Additionally, some of the same methods, hardware, and protocols will be employed in the present investigation to enable direct comparisons to the International Space Station (ISS) "Fluid Shifts" experiment with Chibis-Lower Body Negative Pressure (LBNP). This study will determine the temporal physiological responses of thigh cuff application and removal on ocular and cerebral variables (including invasive ICP) in a microgravity analog. Furthermore, this proposed study will determine tissue pressure distribution applied by thigh cuffs in order to improve comfort, mobility, and efficacy of the countermeasure. Our specific aim is to determine the efficacy of a novel thigh cuff device to mitigate cephalad fluid shifts. We hypothesize that a thigh cuff countermeasure employed in a microgravity analog will temporarily reverse or attenuate ocular and cerebral-volume-pressure variables, approaching normal Earth-based seated posture, the most frequent posture assumed in daily life. In addition, we hypothesize that the magnitude of fluid and pressure redistribution using a thigh cuff countermeasure may require a longer exposure time than that of Chibis-LBNP (using ground-based data from our "Fluid Shifts" project). This project directly addresses Critical Path Roadmap Risks and Questions regarding "Risk of Spaceflight-Induced Intracranial Hypertension/Vision Alterations," and IRP Gap VIIP13: We need to identify preventative and treatment countermeasures to mitigate changes in ocular structure and function and intracranial pressure during spaceflight. METHODS: Noninvasive measures and tissue pressure distributions beneath thigh cuffs The objectives of this study are to: 1) determine the distribution of skin surface pressures beneath the advanced thigh cuff in ten subjects, 2) calibrate the built-in pressure measurement system of the advanced thigh cuff using an industry standard device, and 3) collect subjective feedback and data on the new cuff design to allow for further adjustments prior to invasive studies. A Tekscan Industrial Sensing (I-Scan) system will measure the pressure distribution of the advanced thigh cuff against the skin. In addition, we will measure blood pooling in the thigh and record the circumference of the thigh using Hokanson strain gauge plethysmography. The advanced thigh cuff will be adjusted to obtain a skin contact pressure of 30-50 mmHg as visualized on the Tekscan system. The built-in advanced thigh cuff pressure monitor will be recorded simultaneously to allow direct comparison to the Tekscan measurements. The volunteer will then remove the thigh cuff and remain at rest for five minutes with no legging applied. The thigh cuff will be donned again and pressure measurements will be taken in the same manner for up to 10 repetitions to show reproducibility of pressure after donning. At the conclusion of the study, subjects will be asked to flex their knee, stand, walk, and sit with the thigh cuff activated. During each of these maneuvers the subject will rate their pain/comfort using a modified Borg scale. Effect of thigh cuffs on ICP during simulated microgravity Ommaya reservoir patients will be recruited from the John Wayne Cancer Institute. Ommaya reservoirs provide safe and direct access for the measurement of ICP. Subjects will be instrumented for continuous blood pressure, ECG, and invasive ICP measures. The subjects will be positioned in the upright sitting posture for a 10-minute stabilization period. After the 10-minute stabilization period, imaging measures [ICP, Optical Coherence Tomography, IOP, ocular and vascular ultrasound] will be performed. Following baseline seated measures, the subject will be positioned randomly in the supine, 15deg head-down-tilt, and 15deg head-down-tilt with thigh cuffs and measures repeated. DISCUSSION: Tests to down-select thigh cuff designs will occur in early 2016. Invasive ICP and noninvasive eye imaging tests will begin in spring 2016. Supported by NSBRI through NCC 9-58.

Macias, B.↗