Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Thermal oxidation of nuclear graphite and pyrolytic carbon coatings

The oxidation of pyrolytic carbon (PyC) deposited via fluidized bed chemical vapor deposition was characterized and compared with that of standard nuclear-grade graphite. The materials were heated at 700 to 1000 °C in a thermogravimetric analysis system under 20% v/v O 2 flow, allowing for direct comparison of dynamic oxidative mass change in each material. Further, three different PyC samples fabricated under different conditions exhibited variation in total mass loss and mass loss rate, varying by as much as 709 mg/cm 2 in total mass loss and 14.2 (mg/cm 2 )/min in mass loss rate at a single temperature. These variations highlight the correlation between PyC microstructure/defect density and oxidation susceptibility. Additionally, changes in the microstructure and composition between PyC and graphite were characterized via scanning electron microscopy and correlated to the mass loss results. The results of this work have implications toward the safety of tristructural isotropic (TRISO) and other coated particle fuels, especially under off-normal conditions, given the limited information that exists about the oxidation behavior of PyC.

36 MATERIALS SCIENCE↗

Examination of the α-ω two-phase shock-induced microstructure in zirconium and titanium

Omega (ω) phase is formed in alpha (α) zirconium during dynamic loading and can be retained in the recovered material. The pathway for the α to ω change (or the reverse transformation) is not well understood. Zirconium was shock-loaded and the resulting two-phase microstructure was examined. Electron backscatter diffraction (EBSD) was used to characterize the orientation relationships and habit planes between phases to understand the pathways between α and ω phases and compare to Molecular Dynamics (MD) simulations. Based on key microstructural features, a significant amount of α phase appears to have originated from the reverse transformation from ω-Zr on unloading. Results of microstructural analysis will be discussed, along with implications toward phase transformation pathways.

36 MATERIALS SCIENCE↗

Notch Tensile Behavior of the Mg-Zn-Gd-Zr Alloy

The Mg-Zn-Gd-Zr alloy is one of the important aerospace alloys in the aircraft gearbox applications. The complex geometry of the gearbox introduces several stress concentration points with various intensities. These regions are susceptible to catastrophic failure under mixed loading condition. Therefore, it is important to understand the deformation and failure mode of this alloy for various plastic constraint conditions. In the present work, Mg-4%Zn-1.5%Gd-0.5%Zr alloys were prepared with four different increasing notch root radii (1, 2, 4 and 8 mm). These samples were tested for tensile properties and compared with the smooth condition. In addition, notch sensitivity was determined analytically. The microstructure and fracture samples of the alloy were characterized with the aid of an optical/scanning electron microscope. Tensile test results show that the alloy is notch sensitive and shows notch-strengthening effects. The notch strength ratio increases with the decrease in the notch root radius due to the strong plastic constraint. The predicted and experimental results of the fracture strain with the notch root radius are in qualitative agreement. The void growth rate prediction is qualitatively in agreement with the tensile and fractography results and suggests that the notch geometry has a significant influence on the plastic strain of the alloy. The microstructure of the alloy has equiaxed grains of 74 ± 24 µm with the grain boundary eutectic. The eutectic is composed of Gd-rich Mg phase. The fracture surface has a distinct change from mixed mode to complete cleavage with the increasing notch root radius. The fractography results show that the fracture mode is predominantly intergranular for all the cases.

36 MATERIALS SCIENCE↗

Predicting Fracture Toughness of TRIP 800 using Phase Properties Characterized by In-Situ High Energy X-Ray Diffraction

TRansformation Induced Plasticity (TRIP) steel is a typical representative of 1st generation advanced high strength steel (AHSS) which exhibits a combination of high strength and excellent ductility due to its multiphase microstructure. In this paper, we study the crack propagation behavior and fracture resistance of a TRIP 800 steel using a microstructure-based finite element method with the various phase properties characterized by in-situ high energy Xray diffraction (HEXRD) technique. Uniaxial tensile tests on the notched TRIP 800 sheet specimens were also conducted, and the experimentally measured tensile properties and R-curves (Resistance curves) were used to calibrate the modeling parameters and to validate the overall modeling results. The comparison between the simulated and experimentally measured results suggests that the micromechanics based modeling procedure can well capture the overall complex crack propagation behaviors and the fracture resistance of TRIP steels. The methodology adopted here may be used to estimate the fracture resistance of various multiphase materials.

36 MATERIALS SCIENCE↗

Electronic Durability of Flexible Transparent Films from Type-Specific Single-Wall Carbon Nanotubes

The coupling between mechanical flexibility and electronic performance is evaluated for thin films of metallic and semiconducting single-wall carbon nanotubes (SWCNTs) deposited on compliant supports. Percolated networks of type-purified SWCNTs are assembled as thin conducting coatings on elastic polymer substrates, and the sheet resistance is measured as a function of compression and cyclic strain through impedance spectroscopy. The wrinkling topography, microstructure and transparency of the films are independently characterized using optical microscopy, electron microscopy, and optical absorption spectroscopy. Thin films made from metallic SWCNTs show better durability as flexible transparent conductive coatings, which we attribute to a combination of superior mechanical performance and higher interfacial conductivity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

L2 Milestone 5433: Characterization of Dynamic Behavior of AM and Conventionally Processed Stainless Steel (316L and 304L)

For additive manufacturing (AM) of metallic materials, the certification and qualification paradigm needs to evolve as there currently exists no broadly accepted “ASTM- or DIN-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, design, manufacture, and thereafter implementation and insertion of AM materials to meet engineering applications requires detailed quantification of the constitutive (strength and damage) properties of these evolving materials, across the spectrum of metallic AM methods, in comparison/contrast to conventionally-manufactured metals and alloys. This report summarizes the 316L SS research results and presents initial results of the follow-on study of 304L SS. For the AM-316L SS investigation, cylindrical samples of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS was characterized in both the “as-built” Additively Manufactured state and following a heat-treatment designed to obtain full recrystallization to facilitate comparison with annealed wrought 316L SS. The dynamic shock-loading-induced damage evolution and failure response of all three 316L SS materials was quantified using flyer-plate impact driven spallation experiments at peak stresses of 4.5 and 6.35 GPa. The results of these studies are reported in detail in the first section of the report. Publication of the 316L SS results in an archival journal is planned. Following on from the 316L SS completed work, initial results on a study of AM 304L SS are in progress and presented herein. Preliminary results on the structure/dynamic spallation property behavior of AM-304L SS fabricated using both the directed-energy LENS and an EOS powder-bed AM techniques in comparison to wrought 304L SS is detailed in this Level 2 Milestone report.

316L SS↗

Microstructure and Property Evolution in Advanced Cladding and Duct Materials Under Long-Term and Elevated Temperature Irradiation: Modeling and Experimental Investigation

The in-service degradation of reactor core materials is related to underlying changes in the irradiated microstructure. During reactor operation, structural components and cladding experience displacement of atoms by collisions with neutrons at temperatures at which the radiation-induced defects are mobile, leading to microstructure evolution under irradiation that can degrade material properties. At the doses and temperatures relevant to fast reactor operation, the microstructure evolves by dislocation loop formation and growth, microchemistry changes due to radiation-induced segregation, radiation-induced precipitation, destabilization of the existing precipitate structure, and in some cases, void formation and growth. These processes do not occur independently; rather, their evolution is highly interlinked. Radiation-induced segregation of Cr and existing chromium carbide coverage in irradiated alloy T91 track each other closely. The radiation-induced precipitation of Ni-Si precipitates and RIS of Ni and Si in alloys T91 and HCM12A are likely related. Neither the evolution of these processes nor their coupling is understood under the conditions required for materials performance in fast reactors (temperature range 300-600°C and doses beyond 200 dpa). Further, predictive modeling is not yet possible as models for microstructure evolution must be developed along with experiments to characterize these key processes and provide tools for extrapolation. To extend the range of operation of nuclear fuel cladding and structural materials in advanced nuclear energy and transmutation systems to that required for the fast reactor, the irradiation-induced evolution of the microstructure, microchemistry, and the associated mechanical properties at relevant temperatures and doses must be understood. Predictive modeling relies on an understanding of the physical processes and also on the development of microstructure and microchemical models to describe their evolution under irradiation. This project will focus on modeling microstructural and microchemical evolution of irradiated alloys by performing detailed modeling of such microstructure evolution processes coupled with well-designed in situ experiments that can provide validation and benchmarking to the computer codes. The broad scientific and technical objectives of this proposal are to evaluate the microstructure and microchemical evolution in advanced ferritic/martensitic and oxide dispersion strengthened (ODS) alloys for cladding and duct reactor materials under long-term and elevated temperature irradiation, leading to improved ability to model structural materials performance and lifetime. Specifically, we propose four research thrusts, namely Thrust 1: Identify the formation mechanism and evolution for dislocation loops with Burgers vector of a<100> and determine whether the defect microstructure (predominately dislocation loop/dislocation density) saturates at high dose. Thrust 2: Identify whether a threshold irradiation temperature or dose exists for the nucleation of growing voids that mark the beginning of irradiation-induced swelling, and begin to probe the limits of thermal stability of the tempered Martensitic structure under irradiation. Thrust 3: Evaluate the stability of nanometer sized Y- Ti-O based oxide dispersion strengthened (ODS) particles at high fluence/temperature. Thrust 4: Evaluate the extent to which precipitates form and/or dissolve as a function of irradiation temperature and dose, and how these changes are driven by radiation induced segregation and microchemical evolutions and determined by the initial microstructure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Microstructure and Property Evolution in Advanced Cladding and Duct Materials Under Long-Term Irradiation at Elevated Temperature: Critical Experiments

The in-service degradation of reactor core materials is related to underlying changes in the irradiated microstructure. During reactor operation, structural components and cladding experience displacement of atoms by collisions with neutrons at temperatures at which the radiation-induced defects are mobile, leading to microstructure evolution under irradiation that can degrade material properties. At the doses and temperatures relevant to fast reactor operation, the microstructure evolves by microchemistry changes due to radiation-induced segregation, dislocation loop formation and growth, radiation induced precipitation, destabilization of the existing precipitate structure, as well as the possibility for void formation and growth. These processes do not occur independently; rather, their evolution is highly interlinked. Radiation-induced segregation of Cr and existing chromium carbide coverage in irradiated alloy T91 track each other closely. The radiation-induced precipitation of Ni-Si precipitates and RIS of Ni and Si in alloys T91 and HCM12A are likely related. Neither the evolution of these processes nor their coupling is understood under the conditions required for materials performance in fast reactors (temperature range 300-600°C and doses to 200 dpa and beyond). Further, predictive modeling is not yet possible, as models for microstructure evolution must be developed along with experiments to characterize these key processes and provide tools for extrapolation. To extend the range of operation of nuclear fuel cladding and structural materials in advanced nuclear energy and transmutation systems to that required for the fast reactor, the irradiation-induced evolution of the microstructure, microchemistry, and the associated mechanical properties at relevant temperatures and doses must be understood. This project builds upon joint work at the proposing institutions, under a NERI-C program that is scheduled to end in September, to understand the effects of radiation on these important materials. The objective of this project is to conduct critical experiments to understand the evolution of microstructural and microchemical features (loops, voids, precipitates, and segregation) and mechanical properties (hardening and creep) under high temperature and full dose range radiation, including the effect of differences in the initial material composition and microstructure on the microstructural response, including key questions related to saturation of the microstructure at high doses and temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Figure the impact of steel microstructure and heat treatment on the formation of white etching cracks

White etching crack (WECs) associated macro-pitting is a dominant mode of damage within wind turbine gearbox bearings. This damage is characterized by broadly branching crack networks surrounded by local regions of microstructural alterations. The definitive cause of WECs in the field is unknown; therefore, the implementation of effective mitigation techniques has proven difficult. The current work utilized an accelerated benchtop testing technique in order to quantify differences in performance between through-hardened AISI 52100 steel and carburized AISI 3310 steel. It was found that the carburized AISI 3310 steel demonstrated a more than twofold increase in the time elapsed until WEC macro-pitting damage occurred compared to the through-hardened AISI 52100 steel samples.

36 MATERIALS SCIENCE↗

Microstructure Evolution During Continuous Cooling in AISI 5140 Steel Processed by Induction Heating Chromizing

In this study, induction heating chromizing (IHC) and box-type furnace heating chromizing (BFHC) were conducted on commercial AISI 5140 steels, respectively. Microstructure, microhardness and wear resistance of the chromized samples were characterized. The results show that the IHC samples have thicker Cr coating layer and stronger interface bond due to pre-compressive stress among the packed powders. Three kinds of microstructures including alloyed cementite (AC-layer), fine pearlite zone (FP-zone) and carbon-poor zone (CP-zone) are formed near the interface in the IHC samples. The main reason given for this is that different contents of Cr and C have different effects on pearlite phase and morphology. The IHC sample shows better wear properties due to its stronger interface bonding strength than that of the BFHC sample. The formation mechanism of CP-zone and its influences on microhardness and wear resistance are also discussed.

36 MATERIALS SCIENCE↗

Effect of processing parameters on the formation of C{sub f}/LAS composites/Ag−Cu−Ti/TC4 brazed joint

C{sub f}/LAS composites were successfully jointed to TC4 alloy with Ag−Cu−Ti filler by vacuum brazing. The interfacial microstructure of TC4/C{sub f}/LAS composites joints was characterized by employing scanning electron microscope (SEM), energy dispersive spectrometer (EDS), X-diffraction (XRD) and transmission electron microscopy (TEM). The determination of the thin interfacial reaction layer (TiSi{sub 2} + TiC layer) was realized by TEM. The effect of holding time on the interfacial microstructure and shear strength were investigated. With the increasing holding time, the thickness of diffusion layer, Ti{sub 3}Cu{sub 4} layer, and TiSi{sub 2} + TiC layer increased obviously, on the contrary, that of Ti−Cu intermetallic compound layers decreased gradually. Besides, blocky Ti{sub 3}Cu{sub 4} phase was coarsened when the joint was brazed at 890 °C for 20 min, which deteriorated the mechanical properties of the joint dramatically. The interfacial evolution of TC4/C{sub f}/LAS composites joint and the formation of TiSi{sub 2}, TiC, Ti{sub 3}Cu{sub 4}, TiCu and Ti{sub 2}Cu phases were expounded. The maximum shear strength of 26.4 MPa was obtained when brazed at 890 °C for 10 min. - Highlights: •The thin interface reaction layer was determined to be TiSi{sub 2} + TiC layer by TEM. •Holding time had influence on the interfacial microstructure and joint properties. •Microstructural evolution mechanism and reactions of brazed joints were expounded.

36 MATERIALS SCIENCE↗

High Energy X-ray Applications for the Characterization of Metallic Uranium Alloys

Uranium-based metallic alloys are both candidates for fuels in high performance research and test reactors, as well as in fast spectrum reactors as nuclear transmutation fuels that can be utilized to burn long-lived minor actinides and fission products. Uranium-molybdenum (UMo) alloys are under development for the use in research and test reactors. Whereas, uranium-zirconium (U-Zr) alloys represent one of the types of fuels that are under consideration for use within the fast spectrum reactors. Both of these types of metallic fuels have been studied for over five decades in various types of reactors. Many of the previous studies had focused on performance-based aspects. However, recent advances in characterization tools and techniques, as well as short-term (low fluence) neutron irradiation facilities have contributed to a more in-depth understanding of nuclear fuel and material behavior following irradiation. This knowledge is crucial to the enhancement of current modeling and simulation techniques, particularly with respect to parameterization and validation. This paper focuses on the use of high energy x-rays to characterize metallic nuclear fuel. The specimens were composed of depleted uranium (DU) alloyed with either Zr or Mo, where DU-xZr (x = 10, 15, or 20 wt.%) and DU-yMo (y = 7 or 10 wt.%). The geometries of the specimens were 3 mm TEM disks that were ∼200 μm in thickness. The fuel alloys were initially prepared via an arc melting process. The samples were irradiated at the Advanced Test Reactor at Idaho National Laboratory (INL) using the hydraulic rabbit system. The hydraulic rabbit system allows for well-controlled, short term irradiations (less than one cycle), hence resulting in low fluences. The U-based alloys were irradiated to doses of 0.01 and 0.1 dpa. The irradiation temperature of the specimens ranged from 150 deg. C to 800 deg. C. Synchrotron characterization techniques can be used to provide insight into material microstructure ranging a multitude of spatial scales, from the atomic scale to the macroscale. High-energy x-rays at the National Synchrotron Light Source II (NSLS II) and the Advanced Photon Source (APS) have been utilized to understand the microstructural changes in these metallic alloys, specifically with respect to phase identification, phase fractions, chemical bonding, strain, and dislocation density through the use of diffraction and X-ray Absorption Spectroscopy (XAS). These experiments utilized a robot for specimen exchange during the diffraction measurements, allowing for remote handling of radioactive materials. This is an example of another recent advancement in characterization techniques that enables research with nuclear materials. Detailed results of the analyses of the microstructural changes are pending.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

MICROSTRUCTURE AND MECHANICAL PROPERTY PERFORMANCE OF COMMERCIAL GRADE API PIPELINE STEELS IN HIGH PRESSURE GASEOUS HYDROGEN

The continued growth of the world s developing countries has placed an ever increasing demand on traditional fossil fuel energy sources. This development has lead to increasing research and development of alternative energy sources. Hydrogen gas is one of the potential alternative energy sources under development. Currently the most economical method of transporting large quantities of hydrogen gas is through steel pipelines. It is well known that hydrogen embrittlement has the potential to degrade steel s mechanical properties when hydrogen migrates into the steel matrix. Consequently, the current pipeline infrastructure used in hydrogen transport is typically operated in a conservative fashion. This operational practice is not conducive to economical movement of significant volumes of hydrogen gas as an alternative to fossil fuels. The degradation of the mechanical properties of steels in hydrogen service is known to depend on the microstructure of the steel. Understanding the levels of mechanical property degradation of a given microstructure when exposed to hydrogen gas under pressure can be used to evaluate the suitability of the existing pipeline infrastructure for hydrogen service and guide alloy and microstructure design for new hydrogen pipeline infrastructure. To this end, the 2 Copyright 2010 by ASME microstructures of relevant steels and their mechanical properties in relevant gaseous hydrogen environments must be fully characterized to establish suitability for transporting hydrogen. A project to evaluate four commercially available pipeline steels alloy/microstructure performance in the presences of gaseous hydrogen has been funded by the US Department of Energy along with the private sector. The microstructures of four pipeline steels were characterized and then tensile testing was conducted in gaseous hydrogen and helium at pressures of 800, 1600 and 3000 psi. Based on measurements of reduction of area, two of the four steels that performed the best across the pressure range were selected for evaluation of fracture and fatigue performance in gaseous hydrogen at 800 and 3000 psi. This paper will describe the work performed on four commercially available pipeline steels in the presence of gaseous hydrogen at pressures relevant for transport in pipelines. Microstructures and mechanical property performances will be compared. In addition, recommendations for future work related to gaining a better understanding of steel pipeline performance in hydrogen service will be discussed.

08 HYDROGEN↗

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗

Optical, structural and aging properties of Al/Sc-based multilayers for the extreme ultraviolet

This manuscript presents the structural characterization of Al/Sc-based periodic multilayer coatings for the extreme ultraviolet (EUV) spectral range. Based on transmission electron microscopy and electron diffraction as well as grazing-incidence and large-angle x-ray diffraction, a model for the layer structure and the interfacial effects of Al/Sc coatings is built. The onset of crystallization in nanoscale Al and Sc layers as a function of thickness is also revealed in these characterizations. The Al/Sc layer model is validated and further refined by fitting in-band and out-of-band EUV reflectance measurements across 5 orders of magnitude in an extended wavelength range from 17 to 80 nm. Here, the same type of EUV reflectance measurements is used to test the Al/Sc aging properties and to demonstrate the spectral response of optimized two- and tri-material multilayers including Al/Sc, Al/Sc/SiC and Mo/Al/Sc.

36 MATERIALS SCIENCE↗

Discovery, Design, Synthesis and Testing of High Performance Structural Alloys (Final Technical Report)

The overarching goal of this project is to understand the phase stability and mechanical behavior of non-stoichiometric multi-principal element alloy (MPEA) materials. In order to identify suitable alloys, we plan to use a combinatorial thin film screening approach, in collaboration with scientists at Lawrence Berkeley National Laboratory who are performing computational work as well as complementary experimental work. Specific tasks within the scope of this project include the fabrication, using thin film deposition from six sputtering targets, of combinatorial samples with multi-dimensional gradients in composition and microstructure. These samples are studied to screen MPEA systems for promising candidate alloys with specific composition(s), based on characterization of composition, structure and mechanical behavior across the thin film. We want to produce single-phase MPEAs with chemical homogeneity in a given thin film region, simple grain structures, and no intermetallic phases present. Gradient films facilitate first-pass screening for desirable characteristics and inform the next stage of work that involves fabrication of bulk MPEA specimens for (tensile) mechanical testing and characterization. To make the bulk alloys, metal (elemental) pieces are melted to form MPEAs, followed by heat treatment to homogenize the composition and microstructure. A subset of alloys is also cast, using vacuum arc melting, to yield larger samples (diameter ~1 cm and length ~5-10 cm) and these allow us to assess viability of scale-up for the alloys in structural applications. Further processing plans include rolling and heat treatment to recrystallize selected bulk MPEAs and grow grains to different extents, in order to investigate size effects in the mechanical behavior of MPEAs. Microspecimen testing will be performed (primarily in tension) to assess the mechanical behavior over a range of temperatures. The deformation microstructure of mechanically tested alloys will be characterized using transmission electron microscopy (TEM) to provide a scientific basis for understanding the structure-property relationships in MPEA mechanical behavior.

36 MATERIALS SCIENCE↗

Annealing induced microstructure engineering of antimony tri-selenide thin films

Highlights: • Deposition of Sb{sub 2}Se{sub 3} thin films using thermal vapour deposition. • Films are deposited on substrates with concurrent heating and without heating. • Effect of post deposition annealing on the two types of films are investigated. • Influence of temperature and processing conditions on optical band gap are probed. • This Sb{sub 2}Se{sub 3} films can find application in solar cells and optoelectronic devices. - Abstract: The presented work demonstrates the effect of annealing on the structural, surface morphology and optical properties of Antimony Triselenide (Sb{sub 2}Se{sub 3}) thin films deposited by thermal evaporation. Two sets of thin films of Sb{sub 2}Se{sub 3} were grown on soda lime glass (SLG) substrates by thermal evaporation with and without substrate heating. Both sets of films were then annealed at three distinct temperatures (100 °C, 200 °C and 300 °C) to study the effects of annealing on the microstructure. Analysis using XRD (X-Ray Diffraction) characterization revealed that the as-deposited films without substrate heating exhibit an amorphous nature, whereas the films grown with concurrent substrate heating are polycrystalline with orthorhombic structure. The films annealed at high temperature with concurrent substrate heating possess smooth and continuous grain morphologies. The effect of annealing was also found to have significant impact on the band gap and optical properties of the Sb{sub 2}Se{sub 3} thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phase Behavior and Ionic Conductivity of Concentrated Solutions of Polystyrene-Poly(ethylene oxide) Diblock Copolymers in an Ionic Liquid

Concentrated solutions of poly(styrene-b-ethylene oxide) (PS-PEO) diblock copolymers were prepared using the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMI][TFSI] as the solvent. The self-assembled microstructures adopted by the copolymer solutions have been characterized using small-angle X-ray scattering. Lyotropic mesophase transitions were observed, with a progression from hexagonally packed cylinders of PEO, to lamellae, to hexagonally packed cylinders of PS upon increasing [EMI][TFSI] content. The change in lamellar domain spacing with ionic liquid concentration was found to be comparable to that reported for other block copolymers in strongly selective solvents. The ionic conductivity of the concentrated PS-PEO/[EMI][TFSI] solutions was measured via impedance spectroscopy, and ranged from 1 x 10{sup -7} to 1 x 10{sup -3} S/cm at temperatures from 25-100 C. Additionally, the ionic conductivity of the solutions was found to increase with both ionic liquid concentration and molecular weight of the PEO blocks. The ionic conductivity of PEO homopolymer/[EMI][TFSI] solutions was also measured in order to compare the conductivity of the PS-PEO solutions to the expected limit for a lamellar sample with randomly oriented microstructure grains.

36 MATERIALS SCIENCE↗