Search NASA⌕ Search

SEARCH · Search NASA

Results for “Antimony”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Pyrolyzer Assisted Vapor Transport Deposition of Antimony-Doped Cadmium Telluride

In this study, we developed a new method for in situ Sb doping of CdTe thin films combining vapor transport deposition with a Group V pyrolyzer to address Sb doping concentration and doping efficiency. The Sb doped CdSeTe (CdSeTe:Sb) films were deposited in solar cell structures under variations of Sb dopant source heater, vapor pyrolyzer temperature, and Cd vapor excess. Results indicate that although these parameters do not affect the CdTe morphology or crystal structure, they critically influence doping efficiency and trap concentration. Capacitance-voltage measurements show that a higher dopant heater (TD) or pyrolyzer (TP) temperature leads to higher net carrier concentration, achieving a net carrier concentration of 1016 cm-3 and 20% doping efficiency with a TD/TP combination of 600 degrees C/1100 degrees C. By tuning the Cd/Sb flux ratio during CdSeTe:Sb deposition, the lowest defect concentration is achieved at Cd/Sb of 1.4:1, which produced the best VOC CdSeTe:Sb cell. This demonstrates a path to produce high net carrier concentration polycrystalline CdTe thin film with a low concentration of dopant-induced defects.

14 SOLAR ENERGY↗
DOE OSTI2025

Effect of growth dynamics on the structural, photophysical and pseudocapacitance properties of famatinite copper antimony sulphide colloidal nanostructures (including nanosheets)

Facile phase selective synthesis of copper antimony sulphide (CAS) nanostructures is important because of their tunable photoconductive and electrochemical properties. In this study, off-stoichiometric famatinite phase CAS (fCAS) quasi-spherical and quasi-hexagonal colloidal nanostructures (including nanosheets) of sizes, 2.4–18.0 nm were grown under variable conditions of temperature (60–200 °C), time and oleylamine capping ligand concentration using copper(II) acetylacetonate and antimony(III) diethyldithiocarbamate precursors. Data from powder X-ray diffraction, Raman spectroscopy and high-resolution scanning/transmission electron microscopy confirm the tetragonal structure of the famatinite phase. X-ray photoelectron spectroscopy, transmission electron microscopy and scanning electron microscopy-energy dispersive X-ray spectroscopy data suggest a correlation of particle size, morphology and composition of the off-stoichiometric fCAS nanostructures with growth temperature and time, and oleylamine concentration. The off-stoichiometric Cu 3-a Sb 1+b S 4±c (a, b, c – mole fractions) nanostructures being severely copper-deficient and antimony-rich, exhibit shallow-lying acceptor copper vacancy states, deep-lying donor states of antimony interstitials, sulphur vacancies and antimony-copper antisites and shallow-lying acceptor surface trapping states. Further, these electronic states are likely implicated in tunable UV-visible absorption and bandgaps between 2.3 and 2.8 eV, and broad visible-NIR photoluminescence with fast recombination of radiative lifetimes between 0.2 and 6.2 ns, confirmed from absorption, steady-state and time-resolved photoluminescence spectroscopies. Additionally, cyclic voltammetry and electrochemical impedance spectroscopy confirm that electrodes of the fCAS nanostructures display slightly variable pseudocapacitance of charge-storage primarily via possible sodium ion intercalation with a high specific capacitance of ~84 F g -1 obtained at a scan rate of 5 mV s -1 . Overall, these results show the influence of composition, in particular point defects, phase quality and morphology on the optical and pseudocapacitance properties of fCAS nanostructures, suitable as solar absorbers or electrodes for energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Concentration transient analysis of antimony surface segregation during Si(100) molecular beam epitaxy

Antimony surface segregation during Si(100) molecular beam epitaxy (MBE) was investigated at temperatures T(sub s) = 515 - 800 C using concentration transient analysis (CTA). The dopant surface coverage Theta, bulk fraction gamma, and incorporation probability sigma during MBE were determined from secondary-ion mass spectrometry depth profiles of modulation-doped films. Programmed T(sub s) changes during growth were used to trap the surface-segregated dopant overlayer, producing concentration spikes whose integrated area corresponds to Theta. Thermal antimony doping by coevaporation was found to result in segregation strongly dependent on T(sub s) with Theta(sub Sb) values up to 0.9 monolayers (ML): in films doped with Sb(+) ions accelerated by 100 V, Theta(sub Sb) was less than or equal to 4 x 10(exp -3) ML. Surface segregation of coevaporated antimony was kinematically limited for the film growth conditions in these experiments.

Markert, L. C.↗
NASA NTRS1996

Epitaxial Silicon Doped With Antimony

High-purity epitaxial silicon doped with antimony made by chemical vapor deposition, using antimony pentachloride (SbCI5) as source of dopant and SiH4, SiCI2H2, or another conventional source of silicon. High purity achieved in layers of arbitrary thickness. Epitaxial silicon doped with antimony needed to fabricate impurity-band-conduction photodetectors operating at wavelengths from 2.5 to 40 micrometers.

Huffman, James E.↗
DOE OSTI2024

Rh → Sb Interactions Supported by Tris(8-quinolyl)antimony Ligands

The study of ambiphilic systems combining L-type and Z-type ligands within the same construct has emerged as a field of active investigation, especially in the cases of ligands containing a group 13 element as a σ-acceptor for transition metals. (1) Parallel to these developments, several groups have investigated more atypical systems in which the Z-type ligand is a group 15 element. (2) Our contributions to this area have focused on the use of phosphinostibine ligands for the generation of transition metal complexes in which the antimony moiety acts as a Z-type ligand. (1d,3) We have shown that the magnitude of the resulting M → Sb interaction can be readily modulated by the oxidation state of the antimony atom (4) as well as its charge which can be manipulated by abstraction of anionic ligands. (5) Our work has also shown that these effects can be leveraged to enhance the catalytic properties of the transition metal center. (4,5) Some of the simplest systems that we have investigated are those resulting from the reaction of platinum dichloride with the bis- or tris-phosphinostibines ClSb(o-dppp) 2 and Sb(o-dppp) 3 , respectively (o-dppp = o-(Ph 2 P)C 6 H 4 ). These reactions proceed by oxidative insertion of the stibine into a Pt- Cl bond to produce complexes A and B, (6) respectively (Chart 1). Reasoning that the properties of these complexes may also be influenced by the nature of the L-type buttresses, we have now questioned whether stibines featuring nitrogen donor ligands could also display the redox noninnocence of their phosphine counterparts and support the formation of such complexes. Following up on some of our work with ambiphilic tellurium-quinoline ligands, (7) we now report on the reaction of tris-(8-quinolyl)stibines (8) toward (MeCN) 3 RhCl 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Kinetic control of phase evolution and defect-mediated recombination in AACVD-grown copper antimony sulphide thin films

Copper antimony sulphide (CAS) is a multinary chalcogenide semiconductor in which small deviations from stoichiometry can drive phase competition and strong defect-mediated modulation of optoelectronic properties. However, the systematic roles of copper precursor fraction and deposition time in governing phase evolution, off-stoichiometry, and recombination dynamics in aerosol-assisted chemical vapour deposition (AACVD)-grown undoped CAS thin films remain insufficiently understood. In this work, undoped CAS thin films were deposited by AACVD using Cu(dedtc)2 and Sb(dedtc)3 single-source precursors at 550 °C and a carrier gas flow rate of 150 sccm, while the Cu(dedtc)2 mole fraction (x = 0.15 – 0.55) and deposition time (1 – 2 hours) were systematically varied to probe how growth kinetics influence phase composition, microstructure, and defect-mediated optical properties without post-deposition annealing or extrinsic doping. Increasing copper precursor content drives phase evolution toward tetrahedrite-dominant CAS films at intermediate Cu(dedtc)2 mole fractions, with the film deposited at x = 0.35 exhibiting the strongest tetrahedrite character within the parameter space examined. The films are also copper-rich, antimony-poor, and sulphur-deficient, consistent with off-stoichiometric growth and intrinsic defect formation, plausibly including copper interstitials, Cu-on-Sb antisites, and sulphur vacancies. These growth-dependent compositional deviations are accompanied by tunable indirect optical bandgaps of approximately 1.60 – 2.18 eV and weak visible photoluminescence governed by defect-mediated recombination. Time-resolved photoluminescence reveals bi-exponential decay behaviour with lifetimes of approximately 0.1 – 3.6 ns, with emission dominated by slower donor–acceptor pair recombination and a smaller contribution from faster trap-assisted pathways. Collectively, these results establish an explicit kinetic process–structure–defect–property relationship for AACVD-grown CAS thin films and provide a growth–structure–property framework relevant to future optimization of CAS-based optoelectronic and energy materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Metal ion dopant-induced famatinite to chalcostibite phase transformation of copper antimony sulphide colloidal nanostructures: effect on photophysical and pseudocapacitance properties

Here, the strategic doping of transition metal ions into copper antimony sulphide (CAS) semiconducting nanostructures can significantly influence their photophysical and pseudocapacitive properties, for which there are few reports and therefore is the focus of this study. Accordingly, highly crystalline metal ion (Mn 2+ , Fe 2+ , Co 2+ , Ni 2+ and Zn 2+ ) doped off-stoichiometric copper rich/poor, antimony-rich/poor, and sulphur-poor CAS nanostructures (10–23 nm) were grown via colloidal (hot-injection) synthesis using metal diethyldithiocarbamate precursors. Importantly, metal ion doping significantly influences the structure and composition of the off-stoichiometric CAS nanostructures. Data from powder X-ray diffraction, Raman spectroscopy, high-resolution scanning/transmission electron microscopy, and energy dispersive X-ray spectroscopy confirm that the heavier metal ion dopants induce a novel phase transformation from famatinite (fCAS) to chalcostibite (cCAS) nanostructures. The influence of the metal ion dopants is also observed in the optical properties of as-synthesized nanostructures. This involves blue-shifted ultraviolet-visible absorption, reduced Urbach tailing, and tunable bandgaps between 2.17 and 2.38 eV. Also, the doped nanostructures display broad visible-near infrared photoluminescence via a triple radiative pathway with relatively short decay lifetimes between 0.2 and 6.1 ns. This is mediated by electronic transitions involving intrinsic (copper/antimony/sulphur interstitial) and extrinsic (metal ion interstitial) defect states. Additionally, electrodes prepared from Mn 2+ -doped fCAS nanostructures show enhanced pseudocapacitance via Na+ surface adsorption and intercalation relative to undoped fCAS electrodes, while Zn 2+ -doped cCAS electrodes exhibit pseudocapacitance via a combination of Na+ surface adsorption, intercalation, and redox reactions. These electrodes exhibit reduced charge transfer resistance, improved electronic conductivity and notably enhanced specific capacitance (∼222 F g −1 ), and charge transport, as measured in 1 M Na 2 SO 4 electrolyte via cyclic voltammetry and electrochemical impedance spectroscopy. To this end, the discovery of the metal ion-induced phase transformation presents a new avenue for optimizing the functional properties of fCAS and cCAS nanostructures, highlighting the critical role of metal ion-related defects in controlling the optical and electrochemical properties, towards potential solar absorption and energy storage applications.

25 ENERGY STORAGE↗
NASA NTRS1975

Alkali oxide-tantalum, niobium and antimony oxide ionic conductors

The phase equilibrium relations of four systems were investigated in detail. These consisted of sodium and potassium antimonates with antimony oxide and tantalum and niobium oxide with rubidium oxide as far as the ratio 4Rb2O:llB2O5 (B=Nb, Ta). The ternary system NaSbO3-Sb2O4-NaF was investigated extensively to determine the actual composition of the body centered cubic sodium antimonate. Various other binary and ternary oxide systems involving alkali oxides were examined in lesser detail. The phases synthesized were screened by ion exchange methods to determine mobility of the mobility of the alkali ion within the niobium, tantalum or antimony oxide (fluoride) structural framework. Five structure types warranted further investigation; these structure types are (1) hexagonal tungsten bronze (HTB), (2) pyrochlore, (3) the hybrid HTB-pyrochlore hexagonal ordered phases, (4) body centered cubic antimonates and (5) 2K2O:3Nb2O5. Although all of these phases exhibit good ion exchange properties only the pyrochlore was prepared with Na(+) ions as an equilibrium phase and as a low porosity ceramic. Sb(+3) in the channel interferes with ionic conductivity in this case, although relatively good ionic conductivity was found for the metastable Na(+) ion exchanged analogs of RbTa2O5F and KTaWO6 pyrochlore phases.

Roth, R. S.↗
NASA NTRS1983

Composite thin-foil bandpass filter for EUV astronomy Titanium-antimony-titanium

Thin metallic foils of antimony and titanium have been investigated in an attempt to develop an EUV filter with a bandpass from 350 to 550 A. A composite filter has been developed composed of antimony sandwiched between two titanium foils. The transmissions of sample composite foils and of pure titanium foils from 130 to 1216 A are presented. The absorption coefficients of anatimony and titanium and the effect of titanium oxide on the transmission are derived. The composite filter has been found to be quite stable and mechanically rugged. Among other uses, the filter shows substantial promise for EUV astronomy.

Jelinsky, P.↗
DOE OSTI2024

Facile Access to Organostibines via Selective Organic Superbase Catalyzed Antimony‐Carbon Protonolysis

The selective formation of antimony-carbon bonds via organic superbase catalysis under metal- and salt-free conditions is reported. Here, this novel approach utilizes electron-deficient stibine, Sb(C 6 F 5 ) 3 , to give upon base-catalyzed reactions with weakly acidic aromatic and heteroaromatic hydrocarbons access to a range of new aromatic and heteroaromatic stibines, respectively, with loss of C 6 HF 5 . Also, the significantly less electron-deficient stibines, Ph 2 SbC 6 F 5 and PhSb(C 6 F 5 ) 2 smoothly underwent base-catalyzed exchange reactions with a range of terminal alkynes to generate the stibines of formulae PhSb(C≡CPh) 2 , and Ph 2 SbC≡CR [R=C 6 H 5 , C 6 H 4 -NO 2 , COOEt, CH 2 Cl, CH 2 NEt 2 , CH 2 OSiMe 3 , Sb(C 6 H 5 ) 2 ], respectively. These formal substitution reactions proceed with high selectivity as only the C 6 F 5 groups serve as a leaving group to be liberated as C 6 HF 5 upon formal proton transfer from the alkyne. Kinetic studies of the base-catalyzed reaction of Ph 2 SbC 6 F 5 with phenyl acetylene to form Ph 2 SbC≡CPh and C 6 HF 5 suggested the empirical rate law to exhibit a first-order dependence with respect to the base catalyst, alkyne and stibine. DFT calculations support a pathway proceeding via a concerted σ-bond metathesis transition state, where the base catalyst activates the Sb-C 6 F 5 bond sequence through secondary bond interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Antimony stable isotope fractionation during adsorption onto birnessite: A molecular perspective from X-ray absorption spectroscopy and density functional theory

Sorption of antimony (Sb) onto birnessite significantly influences the fate of Sb in oceanic and terrestrial environments and fractionates Sb isotopes. Nevertheless, little is known about Sb isotopic fractionation during its adsorption on birnessite. Here, in this study, we show the value of Δ 123 Sb adsorbed-aqueous increases from −0.398 to −0.332 ‰ in 1 h and then decreases and stabilizes at −0.384 ‰ in 72 h. The enrichment of the light Sb isotope is predominantly due to the distortion of the octahedral symmetry. X-ray absorption spectroscopy results indicate Sb first forms a double-corner-sharing complex on birnessite and then transforms to a double-edge-sharing complex during adsorption. The optimized bond distances for double-corner-sharing (3.37 Å) and double-edge-sharing (2.90 Å) complexes calculated using density functional theory (DFT) fits well with the structure (3.41 and 3.00 Å) revealed by X-ray absorption spectroscopy, respectively. The fractionation derived from reduced partition function ratios calculated using DFT aligns well with the experimental results. Therefore, the variation in Sb isotopic fractionation during adsorption is attributed to the evolving structure of Sb complexes on birnessite. Our results demonstrate the isotopic fractionation of Sb during adsorption on birnessite and provide a molecular-scale understanding of Sb behavior, contributing to the correct reconstruction of the Sb isotope composition of ancient seawater using ferromanganese crusts and nodules, and efforts to trace Sb migration in epigenetic mining environments.

Adsorption↗
DOE OSTI2025

Resistivity distribution and donor properties of antimony-doped n -type Czochralski silicon ingots

We investigate antimony (Sb)-doped Czochralski-grown silicon as an alternative n-type substrate for photovoltaic applications, and characterize their axial resistivity distribution, donor properties, and mechanical strength. We find that Sb-doped ingots can achieve a more uniform resistivity distribution along the axial direction compared to P-doped counterparts. Dopant concentration profiles in P-doped ingots can be accurately modelled using the standard Scheil's equation, accounting only for dopant segregation during solidification. In contrast, modelling Sb-doped ingots requires consideration of both dopant segregation and evaporation effects to fit the dopant distribution accurately. Using electron paramagnetic resonance spectroscopy at 9 K, we observe two hyperfine lines in P-doped samples, and six hyperfine lines for Sb 121 and eight for Sb 123 isotopes, with the number of hyperfine lines governed by the nuclear spins. We further identify two-atom Sb clustering in the Sb-doped wafers, confirmed through simulations of the additional weak electron paramagnetic resonance peaks. Finally, we find that 140 μm as-cut planar Sb-doped wafers exhibit slightly higher mechanical strength compared to P-doped wafers.

14 SOLAR ENERGY↗
DOE OSTI2025

Pnictogen-Bonding Catalysis: Copolymerization of CO 2 and Epoxides on Antimony(V) Platforms

The copolymerization of CO 2 and epoxides to access polycarbonates represents a promising strategy for CO 2 utilization and for the production of useful polymers. Aiming to explore alternative transition-metal-free approaches that support this chemistry, we have investigated a series of triaryl-catecholatostiboranes as pnictogen-bonding platforms for the copolymerization of CO 2 and cyclohexene oxide (CHO). Our survey of these antimony species has identified motifs that promote this polymerization reaction efficiently, provided that bis(triphenylphosphine)iminium chloride is administered as an activator. By coupling these polymerization studies with a careful assessment of the structure, electronic attributes and Lewis acidity of the catecholatostiboranes, this work shows that high activity is generally observed with the weakest pnictogen-bond donors or Lewis acids investigated. Mechanistic studies, which indicate that the polymerization reaction is first order in stiborane, reveal a nonlinear dependence on the CO 2 pressure. This nonlinear dependence could be satisfactorily modeled based on a pre-equilibrium process involving the reversible insertion of the gaseous monomer into the growing chain. Altogether these findings greatly expand the reach of pnictogen bond catalysis while also providing an entry for the use of heavy group 15 elements as competent platforms for CO 2 utilization.

antimony↗
NASA NTRS1966

Electronic spectrum of crystalline antimony.

Energy levels and interband oscillator strengths of antimony calculated in Brillouin zone by pseudopotential method, predicting polarization effects and spin-orbit splittings

BRILLOUIN ZONE↗