Search NASA⌕ Search

SEARCH · Search NASA

Results for “Chromium doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Effective gain measurements in chromium-doped forsterite

Effective gain cross section in tetravalent chromium-doped forsterite laser crystal was measured over the 1180-1330 nm spectral range. The experiment was performed using two collinear laser beams in a pump-and-probe arrangement. The peak-gain cross section from this measurement is estimated to be 1.9 x 10 to the -19th sq cm at 1215 nm, which is comparable to the value of about 2 x 10 to the -19th sq cm predicted by fluorescence linewidth and lifetime measurements. These results indicate that excited-state absorption is not a major loss mechanism in tetravalent chromium-doped forsterite.

Petricevic, V.↗
NASA NTRS1993

Femtosecond pulses generated from a synchronously pumped chromium-doped forsterite laser

Kerr lens mode-locking (KLM) has become a standard method to produce femtosecond pulses from tunable solid state lasers. High power inside the laser resonator propagating through the laser-medium with nonlinear index of refraction, coupled with the stability conditions of the laser modes in the resonator, result in a passive amplitude modulation which explains the mechanism for pulse shortening. Recently, chromium doped forsterite was shown to exhibit similar pulse behavior. A successful attempt to generate femtosecond pulses from a synchronously pumped chromium-doped forsterite laser with intracavity dispersion compensation is reported. Stable, transform limited pulses with duration of 105 fs were routinely generated, tunable between 1240 to 1270 nm.

Seas, A.↗
NASA NTRS1992

Generation of sub-100-fs pulses from a CW mode-locked chromium-doped forsterite laser

Generation of femtosecond pulses from a continuous-wave mode-locked chromium-doped forsterite laser is reported. The forsterite laser was actively mode locked by using an acoustooptic modulator operating at 78 MHz with two Brewster high-dispersion glass prisms for intracavity chirp compensation. Transform-limited sub-100-fs pulses were routinely generated in the TEM(00) mode with 85 mW of continuous power (with 1 percent output coupler), tunable over 1230-1280 nm. The shortest pulses measured had a 60-fs pulse width.

Seas, A.↗
NASA NTRS2000

The Preparation Conditions of Chromium Doped ZnSe and Their Effect on the Infrared Luminescence Properties

We report the investigation by photoluminescence lifetime measurements of the near-IR emissions from a series of chromium-doped ZnSe samples, correlated to their preparation conditions. The samples were polycrystalline or single crystals prepared by post growth diffusion doping or single crystals doped during growth by the physical vapor transport method. Room temperature lifetime values between 6 and 8 micro seconds were measured for samples with Cr2+ from low 10(exp 17) to high 10(exp 18) / cubic cm range. Lifetime data taken down to 78 K was found to be rather temperature independent, reconfirming previous reports indicating a quantum yield of the corresponding emission of close to 100% at room temperature. A strong decrease in the room temperature lifetime was found for chromium concentrations higher than 10(exp 19) / cubic CM.

Burger, A.↗
NASA NTRS2000

The Preparation Conditions of Chromium Doped ZnSe and Their Effect on The Infrared Luminescence Properties

We report the investigation by photoluminescence lifetime measurements of the near-IR emissions from a series of chromium-doped ZnSe samples, correlated to their preparation conditions. The samples were polycrystalline or single crystals prepared by post growth diffusion doping or single crystals doped during growth by the Physical Vapor Transport method. Room temperature lifetime values between 6 and 8 microseconds were measured for samples with Cr (2+) concentrations from low 10 (exp 17) to high 10 (exp 18) per cubic centimeter range. Lifetime data taken down to 78 K was found to be rather temperature independent, reconfirming previous reports indicating a quantum yield of the corresponding emission of close to 100% at room temperature. A strong decrease in the room temperature lifetime was found for chromium concentrations higher than 10 (exp 19) per cubic centimeter.

Burger, A.↗
NASA NTRS1993

Self-mode-locked chromium-doped forsterite laser generates 50-fs pulses

Stable transform-limited (delta nu-delta tau = 0.32) femtosecond pulses with a FWHM of 50 fs were generated from a self-mode-locked chromium-doped forsterite laser. The forsterite laser was synchronously pumped by a CW mode-locked Nd:YAG (82 MHz) laser that generated picosecond pulses (200-300 ps) and provided the starting mechanism for self-mode-locked operation. Maximum output power was 45 mW for 3.9 W of absorbed pumped power with the use of an output coupler with 1 percent transmission. The self-mode-locked forsterite laser was tuned from 1240 to 1270 nm.

Seas, A.↗
NASA NTRS1988

Laser action in chromium-doped forsterite

This paper reports on pulsed laser operation obtained in chromium-activated forsterite Cr(3+):Mg2SiO4 at room temperature. The spectrum of the free-running laser peaks at 1235 nm and a bandwidth of about 22 nm. The spectral range of the laser emission is expected to extend from 850 to 1300, provided the parasitic impurity absorption may be minimized by improved crystal growth techique.

Petricevic, V.↗
NASA NTRS2008

Tetravalent chromium doped laser materials and NIR tunable lasers

A method is described to improve and produce purer Cr.sup.4+-doped laser materials and lasers with reduced co-incorporation of chromium in any other valence states, such as Cr.sup.3+, Cr.sup.2+, Cr.sup.5+, and Cr.sup.6+. The method includes: 1) certain crystals of olivine structure with large cation (Ca) in octahedral sites such as Cr.sup.4+:Ca.sub.2GeO.sub.4, Cr.sup.4+:Ca.sub.2SiO.sub.4, Cr.sup.4+:Ca.sub.2Ge.sub.xSi.sub.1-xO.sub.4 (where 0<x<1), and/or 2) high-temperature solution growth techniques that enable the growth of the crystals below the temperature of polymorphic transitions by using low melting point solvent based on oxide, fluoride and/or chloride compounds. Purer Cr.sup.4+-doped laser materials are characterized by a relatively high concentration of Cr.sup.4+-lasing ion in crystalline host that makes these materials suitable for compact high power (thin disk/wedge) NIR laser applications.

Alfano, Robert R.↗
DOE OSTI2025

Chromium-doped uranium dioxide fuels: A review

UO 2 doped with parts per million CR 2 O 3 powder is considered a potential near term accident tolerant fuel candidate. Here, the results of decades of industry and academic research into Cr-doped UO 2 are analyzed and their shortcomings are critiqued. Focusing on the incorporation mechanisms of Cr into the fuel matrix, we explore a mechanistic understanding of the characteristic properties of Cr-doped UO 2 , notably, enhanced fission gas retention attributed to enlarged grain sizes following sintering, along with marginal improvements in the thermophysical properties. The findings of recent X-ray Adsorption Near Edge Spectroscopy studies were compared and put into conversation with historic data regarding the incorporation of Cr in UO 2 . On the basis of defect mechanisms, the case is made for the substitutional incorporation of Cr governing the lattice solubility but not the enhanced U diffusivity. Instead, Cr/CR 2 O 3 redox chemistry in a well-defined oxygen potential explains the differences in the U diffusivity and O/M ratio. The primary mechanism of doping enhanced grain growth is found to be liquid assisted sintering due to a CRO (1) eutectic phase at the grain boundaries. The role of inhomogeneities in Cr concentration in UO 2 at various length scales across the materials microstructure is highlighted and connected to promising experimental and modeling work to fill in the gaps in the current understanding of Cr-doped UO 2 . The review considers both the open scientific questions and engineering applications to illustrate the deep connections between the practice and theory in the design of accident tolerant nuclear fuels. In conclusion, the review ends with an outline of future works that combine meticulous irradiation studies and high resolution experiments with next generation modeling and simulations techniques empowered by machine learning advances to accelerate the fabrication and adoption of Cr-doped UO 2 light water reactors.

Cleveland, Mack Wesley [Massachusetts Inst. of Tec↗
DOE OSTI2021

Enhanced extreme ultraviolet high-harmonic generation from chromium-doped magnesium oxide

High-order harmonic generation (HHG) from crystals is emerging as a new ultrashort source of coherent extreme ultraviolet (XUV) light. Doping the crystal structure can offer a new way to control the source properties. Here, we present a study of HHG enhancement in the XUV spectral region from an ionic crystal, using dopant-induced vacancy defects, driven by a laser centered at a wavelength of 1.55 μm. Our numerical simulations based on solutions of the semiconductor Bloch equations and density-functional theory are supported by our experimental observations and demonstrate an increase in the XUV high harmonic yield from doped bulk magnesium oxide (MgO) compared to undoped MgO, even at a low defect concentration. The anisotropy of the harmonic emission as a function of the laser polarization shows that the pristine crystal's symmetry is preserved. Our study paves the way toward the control of HHG in solids with complex defects caused by transition-metal doping.

36 MATERIALS SCIENCE↗
NASA NTRS1997

Chromium Diffusion Doping on ZnSe Crystals

Chromium doped zinc selenide crystal have recently been demonstrated to be a promising material for near-IR room temperature tunable lasers which have an emission range of 2-3 micrometers. In this study a new diffusion doping process has been developed for incorporation of Cr(+2) ion into ZnSe wafers. This process has been successfully performed under isothermal conditions, at temperatures above 800 C. Concentrations in excess of 10(exp 19) Cr(+2) ions/cu cm, an order of magnitude larger than previously reported in melt grown ZnSe material, have been obtained by diffusion doping, as estimated from optical absorption measurements. The diffusivity was estimated to be about 10(exp -8) sq cm/sec using a thin film diffusion model. Resistivity was derived from current-voltage measurements and in the range of 10(exp 13) and 10(exp 16) omega-cm. The emission spectra and temperature dependent lifetime data will also be presented and discussed.

Journigan, Troy D.↗
DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2014

Temperature and Pressure Sensors Based on Spin-Allowed Broadband Luminescence of Doped Orthorhombic Perovskite Structures

Systems and methods that are capable of measuring pressure or temperature based on luminescence are discussed herein. These systems and methods are based on spin-allowed broadband luminescence of sensors with orthorhombic perovskite structures of rare earth aluminates doped with chromium or similar transition metals, such as chromium-doped gadolinium aluminate. Luminescence from these sensors can be measured to determine at least one of temperature or pressure, based on either the intense luminescence of these sensors, even at high temperatures, or low temperature techniques discussed herein.

Eldridge, Jeffrey I.↗
NASA NTRS1997

Cr(+2) Diffusion Doping in ZnSe

Chromium doped zinc selenides crystals have recently been demonstrated to be a promising material for near-IR room temperature tunable lasers which has an emission range of 2-3 pm. In this study, a new diffusion doping process has been developed for incorporation of Cr(+2) ion into ZnSe wafers. This process has been successfully performed under isothermal conditions, at temperatures above 800 degrees Celsius. Concentrations in excess of 10(exp 19) Cr(+2) ions/cu cm, an order of magnitude larger than previously reported in melt grown ZnSe material, have been obtained. The diffusivity was estimated to be about 10-* sq cm/sec using a classical diffusion model. Resistivity was derived from current-voltage measurements and in the 107-10(exp 16) Ohms-cm and increased as function of Cr concentration.

Journigan, Troy D.↗
NASA NTRS1992

Novel Cr(4+)-based tunable solid-state lasers

Spectroscopic and laser properties of chromium-doped forsterite (Cr:Mg2SiO4) are reviewed and future directions in development of other Cr(4+)-doped tunable solid-state lasers are discussed. The unique property of chromium-doped forsterite is that the lasing center was identified as tetravalent chromium (Cr(4+)) substituting for tetrahedrally coordinated Si(4+). Development of chromium-doped forsterite laser may stimulate the generation of a new class of tunable solid state lasers based on tetravalent chromium as a laser active ion for the near-IR eyesafe spectral range. The criteria for the development of new Cr(4+)-based tunable solid-state laser crystals are discussed. We also present current research efforts to identify potential low field host crystals, such as silicates, titanites, and germanates, that may be doped with Cr(4+) as an active ion. These new laser materials are expected to cover the wavelength region from 1 - 2 microns, which may be of great technological importance.

Petricevic, V.↗
NASA NTRS2024

Morphology and Luminescence Properties of Transition Metal Doped Zinc Selenide Crystals

Zinc selenide is an excellent matrix material to dope with rare-earth and transition metal to achieve mid-infrared luminescence to develop high power lasers. The luminescence, morphology and refractive index is significantly affected by the doping and defects generated due to size and valency of dopants, concentration, growth process and convection during the growth. The aim of the study is to investigate effect of point and line defects generated due to low doping of iron and chromium on the emission and morphology of the zinc selenide. Luminescence and morphological properties of large iron and chromium doped zinc selenide single crystals were studied to evaluate the effect of extremely low residual impurities and defects associated with the doping process. The emission properties following both short wavelength (i.e., ultraviolet; 350 – 370 nm) excitation and longer wavelength (i.e., near infrared; 850 – 870 nm) excitation were characterized. Luminescence emission bands were identified in both doped crystals. In addition to the primary emission bands, satellite peaks and intra-center transitions were also observed. Due to local population defects associated with the residual impurities (ppm to ppb) in the Fe-ZnSe and Cr-ZnSe crystals, peak emission wavelengths were observed to shift. Raman studies using 266 and 532 – nm excitation revealed different positions of longitudinal and transverse peaks for Fe-ZnSe and Cr-ZnSe crystals, associated with different levels of defects due to the different ion sizes. The emission bands were found to decrease in intensity due to recombination of residual impurity co-dopants and complex defects generated during growth and fabrication. Cryogenic temperature analyses revealed a very clean emission band due to freezing of some of the point and line defects. An emission band observed at 980 nm for both crystals at room temperature as well as cryogenic temperatures indicates a vibronic peak in ZnSe. The scanning electron microscopy (SEM) images of the local morphology support the conclusion that small crystallites in doped crystals are also present.

Zinc selenide↗
DOE OSTI2020

Grand potential sintering simulations of doped UO 2 accident-tolerant fuel concepts

Chromium-doped UO is a widely-studied near-term deployable accident-tolerant fuel concept because it results in a dense, large-grain structure that increases the fuel resistance to densification, swelling, and fission gas release. A new charged-interstitial mechanism was recently proposed to describe the behavior of dopants like chromium in sintered UO 2 . Based on that mechanism, manganese was suggested as an even stronger dopant than chromium. In the current work we use mesoscale sintering simulations in an effort to validate the new mechanism. We compare the relative behavior of Cr-doped and undoped UO 2 against experimental data in the literature. We also make predictions of the relative behavior of Mn-doped UO 2 . Simulations are done using the phase field-based grand potential sintering model. Dopants have two effects on sintered UO 2 . They marginally increase the densification rate and greatly increase the average grain size. Both of these effects are individually tested in small-scale simulations. Then large 3D sintering simulations are used to test the combined behavior of both effects. The results for the densification rate simulations are consistent with experiments for Cr-doped fuels. However, we note the grain growth rates are lower than what is found in the literature for Cr-doped fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1987

Ohmic contact formation in semi-insulating GaAs using shallow heavily doped p-type layers

The paper describes a simple, safe, and effective method for forming shallow zinc-doped p-type layers on chromium-doped semiinsulating GaAs, using an open-tube diffusion technique. The resulting peak dopant concentration for the 850-C diffusion was 10 to the 20th/cu cm. The contact resistance of ohmic contacts fabricated on these layers was found to be about 0.00005 ohm/sq cm. The variation of the contact resistance across the wafer reflected the variation of the doping concentration.

Bose, Amitava↗