Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dissolution Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Aluminum Alloy (6061-O, 5052-O, and 1100) Dissolution Rate Testing

The dissolution rates of two aluminum alloys (6061-O and 5052-O) were tested to determine which would be able to replace an aluminum alloy that was difficult to procure (6063-T6). The findings of this memo conclude that the dissolution rates of 6061-O and 5052-O are two orders of magnitude slower than 6063-T6. Therefore, it is unlikely that 6061-O and 5052-O would be adequate replacements for 6063-T6 based on similar dissolution rates in a Hg-catalyzed, nitric acid solution. Another area of interest was how temperature variation would influence the dissolution rate of an aluminum alloy (specifically 1100). This separate study found that the dissolution rate of the aluminum alloy below 86 °C was approximately 0.0014 % of the dissolution rate at 94.5°C and above. Therefore, at or below 86 °C the dissolution rate reduces significantly which translates to much longer dissolution times.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Predicting the Dissolution Rate of Borosilicate Glasses using QSPR analysis based on molecular dynamics simulations

Quantitative Structure Property Relationship (QSPR) analysis based on molecular dynamics (MD) simulations is a promising approach for establishing the composition-property relationships of glass and other materials with complex structures. A series of 20 borosilicate and boroaluminosilicate glasses have been modeled by using MD simulations with recently developed effective potentials. Short- and medium-range structures of these glasses were analyzed and, based on these structural information, QSPR analysis of the initial dissolution rate (r0) was made and compared with measured r0 at 90°C and pH 9 using various structural descriptors such as percentage of bridging oxygen species, network connectivity and average ring size. The structural descriptors, Fnet, containing energetic information such as single bond strength and other structural information were also used. It was found that overall network connectivity, average ring size and Fnet give reasonable predictions of the r0 of studied glasses, given the conditions that the glasses are homogeneous and dissolve congruently. Modifying glass compositions to account preferential release of modifiers gives a better prediction for incongruently dissolving glasses. The results were compared with our recent work of predicting glass dissolution behavior from compositions using the topological-constraints-based models.

Du, Jincheng↗
DOE OSTI2021

238 PuO 2 In Vitro Lung Dissolution Rate and Particle Size Determination for Material Involved in the June 8, 2020 Incident at the Los Alamos National Laboratory PF-4 Facility

As part of the LANL response to the June 8, 2020 238 PuO 2 inhalation exposure incident in PF-4, the Nuclear and Radiochemistry Group (C-NR) was asked to assist in determining the lung dissolution rate and particle size distribution of the airborne material. These material characteristics, along with urine and fecal bioassay data, are used by the Radiation Protection Services (RP-SVS) internal dosimetrists to refine dose estimates for exposed workers. Similar to previous studies, an in vitro lung dissolution rate study was performed to assess how fast 238 Pu is cleared from the lungs. Given that PuO 2 is a relatively insoluble material, it dissolves very slowly and requires in vitro studies of 100 or more days to estimate dissolution rates. This report details the results of a 100 day in vitro dissolution rate study and the particle size characteristics of 238 PuO 2 collected on an air filters during the incident. Results show that the 238 PuO 2 involved in this incident has behavior comparable to PuO 2 from previous in vitro studies, with approximately 1% of material dissolving quickly, and 99% of the material dissolving very slowly, with a half-time of approximately 120 years. This is somewhat slower than what was determined in a previous study of LANL 238 PuO 2 , which had an experimental dissolution half-time of 3 years, but significantly faster than 3000 years measured for 239 PuO 2 . Particle size distribution measurements indicate that particle sizes range from 0.10 µm – 6 µm, with most < 2 µm, which is reasonable based on our understanding of the process history of the 238 PuO 2 . Particle size, specific surface area, calcining temperature, specific activity, and age all are known factors that can impact the dissolution rate of refractory materials, however, there are too few studies to quantify the exact influence of these parameters on a measured dissolution rate. The results of this study add to that knowledge base, and provide new insights into the dissolution rates for this LANL process-specific 238 PuO 2 material.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Incorporation of trace metals in Hanford waste boehmite mineral phases and dissolution rate impacts

Abstract Data from radioactive Hanford tank waste samples was analyzed to assess whether trace metals present were incorporated into the bulk boehmite matrix or were simply intermingled with the bulk material and subsequent impacts to the boehmite dissolution rate. Results suggest that chromium is primarily blended into the bulk boehmite, with a small fraction present on the surface of the solids. However, increasing the level of chromium incorporation 30‐fold decreased the dissolution rate of boehmite by only 8%, suggesting incorporation of chromium into these samples had a minimal impact on the dissolution rate. Iron was also found to be incorporated in the boehmite solids. Silicon appears to be simply intermingled and not blended into the boehmite crystals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Can a simple topological-constraints-based model predict the initial dissolution rate of borosilicate and aluminosilicate glasses?

Tuning glass composition to obtain targeted properties generally relies on empirical approaches. However, a deep understanding of the physical and chemical mechanisms linking glass composition to its structure and properties would enable developing reliable predictive models. Indeed, although empirical models are usually able to interpolate composition–property relationships within a given compositional envelope, they often fail at extrapolating predictions far from their training domain. Here, as an alternative route to empirical models, we show that a structural descriptor based on the number of topological constraints per atom can be used to predict the initial dissolution rate of aluminosilicate and borosilicate glasses after being parameterized on different families of glasses (specific series of borosilicate glasses). Sixteen glasses belonging to these families were studied and their initial dissolution rates were determined at 90 °C and pH 90 °C = 9, covering rates spanning over 5 orders of magnitude. The model based on topological constraints was trained based on seven select borosilicate glasses (R 2 = 0.997) and used to predict the dissolution rate of nine additional borosilicate and aluminosilicate glasses. We show that, provided that corrections are made for high alkali content glasses that dissolve incongruently (preferential release of Na), the model gives reasonable predictions, even far from its training domain.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Geo‐Structurally Based Correction Factor for Apparent Dissolution Rates in Fractured Media

Abstract Field measurements of apparent geochemical weathering reaction rates in subsurface fractured porous media are known to deviate from laboratory measurements by multiple orders of magnitude. To date, there is no geologically based explanation for this discrepancy that can be used to predict reaction rates in field systems. Proposed correction factors are typically based on ad hoc characterizations related to geochemical kinetic models. Through a series of high‐fidelity reactive transport simulations of mineral dissolution within explicit 3D discrete fracture networks, we are able to link the geo‐structural attributes with reactive transport observations. We develop a correction factor to linear transition state theory for the prediction of the apparent dissolution rate based on measurable geological properties. The modified rate law shows excellent agreement with numerical simulations, indicating that geological structure could be a primary reason for the discrepancy between laboratory and field observations of apparent dissolution rates in fractured media.

58 GEOSCIENCES↗
DOE OSTI2022

Predicting initial dissolution rates using structural features from molecular dynamics simulations

Predicting chemical durability of glass materials is important for various applications from daily life such as drink glass and kitchen ware to advanced technologies such as nuclear waste disposal and biomedicine. In this work, we explored prediction of initial dissolution rate through structural features from molecular dynamics (MD) simulations for a wide range of glass compositions (total 28) including borosilicate and aluminosilicate glasses, ZrO 2 -containing and V 2 O 5 -containing boroaluminosilicate glasses. The initial dissolution rates (r 0 ) measured experimentally at 90 °C with varying solution conditions were correlated with structural features (e.g., polyhedral linkages and non-bridging oxygen species) obtained from MD simulations, either from this study or from literature. Since hydrolysis of the glass network through breaking of the network former linkages (e.g., Si-O-Si, Si-O-Al, etc.) is a critical step of network glass dissolution, the statistics of these linkages obtained from MD were correlated to r0 through linear regression, where the coefficient of determination (R 2 ) and root mean square error are found to be 0.949 and 0.681, respectively. This model was compared and discussed with existing models developed by various approaches including machine learning, the kinetic rate equation, topological constraint theory, and other descriptors from MD simulations. The discussion provides insights on future model improvements to predict glass dissolution. In addition, the impact of V 2 O 5 on the glass dissolution was examined in detail, implicating that the impact is not the same across all glass compositions and test conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solubility and Dissolution Rate of LiCl-KCl-NaCl

This work aims to determine the potential risk of directly storing waste salt from the electrorefining process of used nuclear fuel in a geologic repository. To accomplish this, the solubility limit and dissolution rate of four representative chloride salt mixtures (solutes) in water and two brine solutions (solvents) are observed and documented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Anodic Dissolution Rates Accelerate with Decreasing MoS 2 Nanoflake Thickness

Electrochemical gating of 2D transition metal dichalcogenide (TMD) electrodes is an emerging frontier in the field of semiconductor electrochemistry. In this approach, an applied bias modifies the charge carrier concentration of the 2D TMD, causing band edge shifts and drastic changes in charge transfer rates. However, leveraging this effect for (photo)electrocatalysis is practically limited by the stability of the TMD material under gating conditions. Gerischer showed anodic dissolution of bulk TMD electrodes can occur in the dark and hypothesized that the reaction proceeds via an electron tunneling mechanism from surface states to the TMD conduction band [H. Gerischer, D. Ross, and M. Lubke, Z. Physickalische Chem., 139, 1 (1984)]. Here we investigate this possibility in single MoS 2 nanoflakes using in situ optical microscopy and explore whether Gerischer’s electron tunneling mechanism can explain anodic dissolution rates of thin 2D semiconductors. Here, spatially resolved measurements show anodic dissolution initiates at perimeter edge sites and accelerates exponentially with decreasing layer thickness, consistent with Gerischer’s tunneling mechanism. Interestingly, single layer MoS 2 is impervious to anodic dissolution at applied potentials >200 mV more positive than those required to drive dissolution in bulk and multilayer-thick nanoflakes.

2D semiconductor↗
DOE OSTI2022

Alternate Analysis of an In Vitro Solubility Study on the Lung Dissolution Rate of 238PuO2 Material Involved in the 2020 Incident at Los Alamos National Laboratory

Here this work presents an alternate analysis of an in vitro solubility study on the lung dissolution rate of 238 PuO 2 material involved in a recent inhalation incident at Los Alamos National Laboratory (LANL). The original dataset used in this work was retrieved from a recently published report. The present work shows an analysis of the same dataset by modeling the dissolution in separate time intervals rather than modeling the cumulative dissolution.

238Pu↗
DOE OSTI2021

Manganese uptake by red maples in response to mineral dissolution rates in soil

Manganese (Mn) is an essential plant micronutrient that influences photosynthesis, ecosystem productivity, and soil carbon storage. Our objective was to quantify how Mn uptake by forest vegetation relates to Mn release into soil solution through mineral dissolution. In this work, a greenhouse pot experiment was conducted to quantify Mn uptake by red maple saplings as a function of mineral solubility to test whether Mn uptake was limited by the supply of Mn to soil solution. Differences in soil microbial community composition between treatments, particularly amongst Mn cycling bacteria and fungi, were also evaluated to assess potential microbial impacts on observed Mn fluxes. Plant Mn uptake was highest in systems supplied with dissolved Mn(II) because it was not kinetically limited by mineral weathering. Mn uptake was also higher in systems supplied with a fast-weathering substrate (shale containing Mn(II)-bearing pyrite) than a slow-weathering substrate (Mn(IV)-oxide). However, vegetation accumulated a decreasing proportion of available Mn with increasing solubility, indicating that uptake was tempered relative to solubility. The presence of bacterial phyla containing known Mn-oxidizing bacteria indicates the potential for Mn-oxidizing bacteria to influence Mn solubility within Mn-oxide and dissolved Mn treatments. A relatively low abundance of these bacteria points to their limited capacity to oxidize and retain Mn in the shale treatments, consistent with substantial Mn leaching. We conclude that Mn uptake was primarily controlled by dissolution rates of Mn-bearing minerals but modified by biological processes. The quantitative framework presented here can guide understanding of how biogeochemical processes control element cycling between plants and soils.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

On the dissolution of a borosilicate glass with the use of isotopic tracing – Insights into the mechanism for the long-term dissolution rate

An understanding of the mechanisms responsible for controlling the long-term corrosion rate of nuclear waste glass is paramount if reliable glass dissolution models are to be used to calculate the controlled release of radionuclides from nuclear waste glass under geologic disposal conditions. Additionally, understanding silicate glass dissolution is also important for natural glasses to understand the role from the dissolution of these glasses has on the composition of natural aquatic systems. Two general mechanisms appear to be responsible for the elemental release from glass to the surrounding biosphere - ion exchange (release principally of alkalis) and matrix dissolution (release of the structural components of the glass). Key unknowns related to these mechanisms are the impact of surface layers on the altered glass and how these layers participate in corrosion. To better understand the impact of these layers on glass corrosion, we made two glasses of the same elemental composition, but with selected elements enriched in specific isotopes, e.g. more 10 B than 11 B. We reacted these glasses for 1 y then the solutions from each were exchanged and the chemistry of the solutions and the solids were followed for another 2 y and in some cases 3 y. This allowed us to follow changes in the glasses with respect to these elements and how these elements were transported through the alteration layers with time and, for at least one element, into the glass. Results from these experiments demonstrate that the release behavior of different elements is strongly dependent on their structural role in the glass (e.g. network formers and modifiers), but, more importantly, the role of water transport and subsequent ion exchange has in the long-term dissolution of the glass studied here. In this article, we highlight the behavior of four elements: lithium, sodium, silicon, and boron. Lithium and sodium, network modifying elements, have similar chemistries. The behavior of Li could be tracked in more detail by following both 6 Li and 7 Li; Li penetrates through the gel layer in both directions without hinderance and into and released from the glass deeper than sodium. Silicon, a network forming element, reacts with the silica-rich alteration layer. Boron, a network forming element, does not accumulate in the gel or the pristine glass and has a very sharp elemental profile between the pristine glass and alteration layer. Boron, lithium, and sodium elemental profiles suggest that there is little if any transport control within the alteration layer. The correlation between the Li and Na profiles and that of a water species suggest that the limiting release is a steady state between the diffusion of a water species and matrix dissolution that results in a low release rate for alkali and this provides a steady driving force for the long-term dissolution of glass.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Metallurgical Analysis of the High Flux Isotope Reactor (HFIR) Carrier Lifting Bails (Rev.1)

The dissolution rates of the aluminum alloys in the High Flux Isotope Reactor (HFIR) element carriers and the Material Test Reactor (MTR) L-bundles in the H-Canyon facility have been identified as the possible cause of extended dissolutions that result in significant time and financial expenditures. A study, carried out by Savannah River National Laboratory (SRNL) to determine relationships between the dissolution rates and the metallurgical properties of the aluminum alloy materials of construction of the HFIR carriers and the L-bundles, considered the dissolution rates of aluminum alloy (AA) series 1100, 6061, and 6063. The study determined that the aluminum alloy compositions played a principal role in the dissolution rate of the carrier/bundle components. Higher dissolution rates were correlated with lower concentrations of the minor element additions in the alloys and with specific element concentrations. Aluminum alloys 1100 and 6063 were found to have similar dissolution rates that were approximately two orders of magnitude (100X) greater than those of AA6061. Based on the results of the dissolution behavior study, a Technical Assistance Request (TAR) was first issued to determine if the replacement of AA6061-T6 with AA6063-T6 is feasible for the HFIR carrier lifting bails. A Technical Task Request was then issued to consider AA6063-T5 as well as other alloys to improve possible supply chain issues. The metallurgical properties of the L-bundle (specifically the end caps) were not evaluated in this report because L-Bundle drawings already allow for the use of AA6063-T6 in all structural components. The HFIR carriers are composed of thin-walled components with significant surface areas that allow for relatively quick overall dissolution times. Conversely, the carrier lifting bails and the supporting constituents are composed of solid bars and thick plate regions with relatively small surface areas that experience longer overall dissolution times. While the MTR L-bundle design includes allowances for the materials of construction to be either AA6061-T6 or AA6063-T6, the HFIR carriers are specified to be constructed fully with AA6061-T6 alloy. This report analyzes the recommendations of the dissolution behavior study to replace the materials of construction of the HFIR carrier lifting bails. The analysis considers the operational requirements of the lifting bail and its supporting structures. To decrease dissolution times, the analysis considers direct replacement of the material as well as reductions in the thicknesses of the components to decrease the mass of the elements. Material reductions are considered on options for using either AA6061 and/or AA6063. The calculations are based on specifications from the American Society of Mechanical Engineer (ASME) and The Aluminum Association, Inc. design codes. The analysis finds that direct replacement of the lifting bail material of construction with AA6063-T6, and AA6063-T5 as well as reductions in the dimensions of the lifting bail components are acceptable. Note that this study considers the structural suitability of the alloys. It does not consider their dissolution rates in the dissolvers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Stability of plutonium oxide nanoparticles in the presence of montmorillonite and implications for colloid facilitated transport

The physical and chemical stability of PuO 2 nanoparticles (intrinsic colloids) in groundwater will control their transport and may affect the performance of high-level radioactive waste repositories. In this study, we examined the chemical stability of two types of PuO 2 nanoparticles at both 25 and 80 °C. The “alkaline” PuO 2 nanoparticles were prepared by neutralizing an acidic Pu(IV) solution with dilute NaOH to pH ~9.5. The “acidic” PuO 2 nanoparticles were precipitated from 0.1 M nitric acid by heating a Pu(IV) solution at 60–80 °C for 30 min. The chemical stability of these PuO 2 nanoparticles was tested in the presence of montmorillonite, a common mineral in the environment and potentially relevant backfill material in some nuclear waste repository designs. The “alkaline” PuO 2 nanoparticles were found to be unstable over a timescale of months at both 25 and 80 °C, with elevated temperature enhancing their dissolution rates and sorption to montmorillonite. PuO 2 nanoparticle dissolution rates decreased with increasing Pu concentration, consistent with solution saturation. The “acidic” PuO 2 nanoparticles appeared to remain stable for much longer than the “alkaline” PuO2 nanoparticles. The “alkaline” PuO 2 nanoparticle dissolution rate constants were as high as 10 -11.9±0.4 mol m -2 s -1 and 10 -11.2±0.2 mol m -2 s -1 at 25 and 80 °C, respectively, while the “acidic” PuO 2 nanoparticle dissolution rate at 80 °C was 10 -13.5 mol m -2 s -1 . Based on transmission electron microscopy, the “alkaline” and “acidic” PuO 2 nanoparticles were of similar size (2.5–4.5 and 2–3 nm nanoparticles, respectively). However, the “acidic” PuO 2 nanoparticles formed more ordered nanoparticle aggregates. Our results suggest that the specific conditions experienced during PuO 2 nanoparticle formation could significantly affect the stability of PuO 2 in the presence of competing sorption processes and, in turn, the relative importance of intrinsic versus pseudocolloid transport in the environment.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Effects of crystallographic orientation on calcite dissolution under alkaline conditions

Here, this study investigates the dissolution of calcite’s (104) and (100) surfaces under alkaline conditions (pH 8.8–13.1) using vertical scanning interferometry under flow-through conditions. The dissolution rate of (100) surfaces decreases with increasing pH. For example, the dissolution rate at pH 8.8 is more than 20 times higher than that at pH 13.1. In contrast, the dissolution rate of (104) surfaces is far less sensitive to pH. We explain these observations as being on account of the preferential adsorption of [OH – ] on (100) surfaces, inhibiting their dissolution. Particularly, this is because Ca-surface sites on (100) surfaces are less coordinated and have a stronger tendency for [OH – ] adsorption. As a result, (100) surfaces dissolve nearly twice as fast as (104) surfaces at pH 8.8, whereas (104) surfaces dissolved ~4.5 times faster than (100) surfaces at pH 13.1; indicating an inversion in dissolution behavior. The dissolution rate of (104) surfaces at pH 13.1 is 60 % of the rate at pH 10–12 because of the formation of slow dissolving microfacets of other orientations. The rhombohedral dissolution etch-pits formed on (104) surfaces, at lower pH’s, disappeared upon exposure to solutions with pH > 12 and were replaced by protrusions. The addition of up to 4m (molality) NaCl enhances the dissolution of (104) surfaces at pH 8.8–13.1 and (100) surfaces at pH 8.8–11.0, and inhibited the dissolution of (100) surfaces at pH = 12.0–13.1. In addition, the competing adsorption between OH – and CO 3 2– species mitigates the inhibition effects of CO 3 2– on both surfaces at pH 13.1 compared to pH 11, and the dissolution of (100) surfaces is far less affected by CO 3 2– than (104) surfaces. These results provide new insights into the rates and mechanisms of how crystallographic orientations affect calcite’s dissolution at alkaline pH conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Epsilon Metal: A Waste Form for Noble Metals from Used Nuclear Fuel

Epsilon metal (e-metal) is the metallic phase that forms as inclusions at the grain boundaries in the UO2 fuel during reactor operation. This metal is composed of Pd, Mo, Rh, Ru, and Tc. These metallic inclusions are insoluble in strong acid and remnants of these metallic inclusions have been found in the UO2 matrix that remains from the natural reactors in Gabon that were active 1.8 billion years ago, therefore e-metal should be an excellent waste form for the immobilization of the long-lived isotopes 107Pd (6.5 ? 106 a) and 99Tc (2.13 ? 105 a), with 99Tc being the isotope of interest for repository performance. Therefore, the chemical durability of this potential waste form is assessed in this study. Typically, corrosion rates for metallic materials are measured electrochemically because they are quick, inexpensive, and can reveal the mechanism by which a metal corrodes, at least initially. However, in a repository the waste form would be subjected to slowly flowing water without an applied electrical potential over long time periods. Therefore, the corrosion rates of e-metal specimens were measured with both electrochemical tests and the single-pass flow-through test (SPFT). Potentiodynamic and potentiostatic polarization results suggest that a thin passive film exists on the alloy surface, which seems to be responsible for its high corrosion resistance. Additionally, X-Ray photoelectron spectroscopic results suggest that Pd oxides are significantly enriched in the passive film Results from the SPFT show that the dissolution rates were weakly dependent on pH. Only Mo and Re were found in solution and were used for the calculation of the dissolution rates. In general, the electrochemically determined corrosion rates agree reasonably well with the initial dissolution rate measured with the SPFT test, but they are about one or two orders of magnitude higher than the steady state rates. The causes for this discrepancy are discussed.

epsilon-metal, nuclear waste form, corrosion, sing↗