Search NASA⌕ Search

SEARCH · Search NASA

Results for “Doped Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Compression-ignition engine performance with undoped and doped fuel oils and alcohol mixtures

Several fuel oils, doped fuel oils, and mixtures of alcohol and fuel oil were tested in a high-speed, single-cylinder, compression-ignition engine to determine power output, fuel consumption, and ignition and combustion characteristics. Fuel oils or doped fuel oils of high octane number had shorter ignition lags, lower rates of pressure rise, and gave smoother engine operation than fuel oils or doped fuel oils of low octane number. Higher engine rotative speeds and boost pressures resulted in smoother engine operation and permitted the use of fuel oils of relatively low octane number. Although the addition of a dope to a fuel oil decreased the ignition lag and the rate of pressure rise, the ensuing rate of combustion was somewhat slower than for the undoped fuel oil so that the effectiveness of combustion was practically unchanged. Alcohol used as an auxiliary fuel, either as a mixture or by separate injection, increased the rates of pressure rise and induced roughness. In general, the power output decreased as the proportion of alcohol increased and, below maximum power, varied with the heating value of the total fuel charge.

Moore, Charles S↗
DOE OSTI2026

PWR Core Analysis for Cycle Extension and Uprates with LEU+ Accident Tolerant Fuel and 80 GWd/Tonne Burnup Limit

The U.S. Nuclear Regulatory Commission has recently drafted a rule enabling fuel burnup increase in light water reactors up to 80 GWd/t. In conjunction with use of fuel enrichment up to 10%, and accident tolerant fuel (ATF), this is anticipated to facilitate 24-month cycles in PWRs, along with further power uprates. In this paper, PWR core analysis is performed for 20% increased PWR power output along with cycle extension up to 24 months, in combination with use of chromia-doped fuel and chromium-coated clad, considered to be the most near-term ATF concepts. In combination, these lead to challenging conditions with a core average discharge burnup of up to ~74 GWd/t, challenging even the 80 GWd/t burnup limit. Analysis is performed using the 2-step method with POLARIS (within SCALE) used for the lattice calculations and PARCS for the core calculations. Core designs are first baselined for current operating conditions (LEU, 62 GWd/t discharge burnup limit) and then derived that meet cycle constraints on power distribution and the updated lead pin discharge burnup limit while maintaining at least two batches of fuel in the core. Gadolina loadings in fuel pins of up to 8% are used, with enrichment zoning both within the core and, to a limited extent, within assemblies. Here, doped fuel with coated cladding can utilize the same core designs as the reference UOX cores, exhibiting slightly lower burnup due to higher fuel density, which also offsets the slight reactivity penalty from the doping and coating. For the analysis performed here, doped fuel enabled a core with 24-month cycle and 20% uprate to stay within the 80 GWd/t lead pin discharge burnup limit.

LEU+↗
DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Chromium-doped uranium dioxide fuels: A review

UO 2 doped with parts per million CR 2 O 3 powder is considered a potential near term accident tolerant fuel candidate. Here, the results of decades of industry and academic research into Cr-doped UO 2 are analyzed and their shortcomings are critiqued. Focusing on the incorporation mechanisms of Cr into the fuel matrix, we explore a mechanistic understanding of the characteristic properties of Cr-doped UO 2 , notably, enhanced fission gas retention attributed to enlarged grain sizes following sintering, along with marginal improvements in the thermophysical properties. The findings of recent X-ray Adsorption Near Edge Spectroscopy studies were compared and put into conversation with historic data regarding the incorporation of Cr in UO 2 . On the basis of defect mechanisms, the case is made for the substitutional incorporation of Cr governing the lattice solubility but not the enhanced U diffusivity. Instead, Cr/CR 2 O 3 redox chemistry in a well-defined oxygen potential explains the differences in the U diffusivity and O/M ratio. The primary mechanism of doping enhanced grain growth is found to be liquid assisted sintering due to a CRO (1) eutectic phase at the grain boundaries. The role of inhomogeneities in Cr concentration in UO 2 at various length scales across the materials microstructure is highlighted and connected to promising experimental and modeling work to fill in the gaps in the current understanding of Cr-doped UO 2 . The review considers both the open scientific questions and engineering applications to illustrate the deep connections between the practice and theory in the design of accident tolerant nuclear fuels. In conclusion, the review ends with an outline of future works that combine meticulous irradiation studies and high resolution experiments with next generation modeling and simulations techniques empowered by machine learning advances to accelerate the fabrication and adoption of Cr-doped UO 2 light water reactors.

Cleveland, Mack Wesley [Massachusetts Inst. of Tec↗
DOE OSTI2025

Accelerated and heterogeneous corrosion of Cr-doped uranium nitride fuel pellets

The steam oxidation of Cr-doped UN fuel pellets is analyzed during sequential isothermal holds up to 720 °C. In situ neutron diffraction results show how Cr is accommodated in a secondary U 2 CrN 3 phase, leading to the formation of a duplex UN/U 2 CrN 3 microstructure. Under corrosion, the oxidation of the two phases begins at 400 °C for UN and 430 °C for U 2 CrN 3 , respectively. Because the UN phase is preferentially oxidized in the presence of U 2 CrN 3 , addition of Cr in UN based nuclear fuel is found to accelerate the corrosion rate. At 430 °C the oxidation of UN in the UN/U 2 CrN 3 microstructure is ~ 5 times faster than pure UN, increasing to ~19 times faster at 460 °C. The oxidation of U 2 CrN 3 produces UO 2 via the formation of two transient intermediate phases. In situ neutron diffraction enables oxidation processes of UN and U 2 CrN 3 components to be followed separately within the two-phase system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan details the strategy, mission, scope, and goals—both near-term and long-term—along with the structure and organization of nuclear fuels and materials research, development, and demonstration (RD&D) activities within the Fuel Cycle Technologies (FCT) program. The FCT program, tasked by the U.S. Department of Energy (DOE), employs a science-based approach to advance fuel technologies. This approach integrates theory, experiments, and multi-scale modeling and simulation (M&S) to develop a predictive understanding of fuel fabrication processes and fuel/cladding performance under irradiation, moving beyond traditional empirical methods. The long-term goals of the AFC are guided by the AFC Strategic Plan and align with the DOE Office of Nuclear Energy (NE) Roadmap [1], which outlines a multi-decade vision for demonstrating and qualifying advanced fuel forms to support diverse fuel cycle options. Near-term goals focus on enhancing accident tolerant fuels (ATF) for Light Water Reactors (LWR), a significant challenge that demands balancing immediate objectives with ongoing progress toward advanced reactor missions. Accelerating the traditional fuel qualification process to meet ATF objectives is another critical challenge. A detailed set of 5-year goals, summarized below, has been developed in line with the overarching science-based fuel development approach: • Advanced LWR Fuel Technologies: By 2027, support the development of advanced LWR fuel technologies with improved performance and enhanced accident tolerance. This includes high burnup (HBu), low enriched uranium (LEU)+, coated cladding, and doped fuel, aimed at complementing industry-led significant LWR uprates and plant refurbishments. • Tristructural Isotropic (TRISO) Fuel: Achieve qualification by 2028 and develop improved designs for emerging markets. • Metal Fuel: Achieve qualification by 2028 and develop improved designs for emerging markets. • Molten Salt Fuel: By 2027, deploy a robust program that enables fuel salt qualification technologies needed to support fuel salt research and development (R&D), focusing on emergent needs to derisk fuel salt production and utilization in advanced reactors. • Long-Term ATF: Develop fuel technologies that enable significant power uprates (~50%) in refurbished or new LWRs while optimizing fissile material utilization and waste disposal. The 5-year milestones in the AFC Execution Plan are contingent on an assumed budget. This Execution Plan will be updated annually to reflect actual funding profiles as budget guidance becomes available, ensuring milestones are adjusted accordingly. In summary, the AFC Execution Plan presents a comprehensive strategy to advance nuclear fuel technologies through a science-based approach, addressing both near-term and long-term goals while adapting to funding realities.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1983

Critical research and advanced technology (CRT) support project

A critical technology base for utility and industrial gas turbines by planning the use of coal-derived fuels was studied. Development tasks were included in the following areas: (1) Combustion - investigate the combustion of coal-derived fuels and methods to minimize the conversion of fuel-bound nitrogen to NOx; (2) materials - understand and minimize hot corrosion; (3) system studies - integrate and focus the technological efforts. A literature survey of coal-derived fuels was completed and a NOx emissions model was developed. Flametube tests of a two-stage (rich-lean) combustor defined optimum equivalence ratios for minimizing NOx emissions. Sector combustor tests demonstrated variable air control to optimize equivalence ratios over a wide load range and steam cooling of the primary zone liner. The catalytic combustion of coal-derived fuels was demonstrated. The combustion of coal-derived gases is very promising. A hot-corrosion life prediction model was formulated and verified with laboratory testing of doped fuels. Fuel additives to control sulfur corrosion were studied. The intermittent application of barium proved effective. Advanced thermal barrier coatings were developed and tested. Coating failure modes were identified and new material formulations and fabrication parameters were specified. System studies in support of the thermal barrier coating development were accomplished.

Furman, E. R.↗
DOE OSTI2023

Engine Operating Conditions, Fuel Property Effects, and Associated Fuel–Wall Interaction Dependencies of Stochastic Preignition

This work for the Coordinating Research Council (CRC) explores dependencies on the opportunity for fuel to impinge on internal engine surfaces (i.e., fuel–wall impingement) as a function of fuel properties and engine operating conditions and correlates these data with measurements of stochastic preignition (SPI) propensity. SPI rates are directly coupled with laser–induced florescence measurements of dye-doped fuel dilution measurements of the engine lubricant, which provides a surrogate for fuel–wall impingement. Literature suggests that SPI may have several dependencies, one being fuel–wall impingement. However, it remains unknown if fuel-wall impingement is a fundamental predictor and source of SPI or is simply a causational factor of SPI. In this study, these relationships on SPI and fuel-wall impingement are explored using 4 fuels at 8 operating conditions per fuel, for 32 total test points. The fuels were directly injected at two different injection timings: an earlier injection timing that initially targets the piston crown and a later injection timing that targets the cylinder liner. At each injection timing, the engine was operated at both 90°C and 70°C coolant and lubricant temperatures, and 185 and 200 kPa absolute intake manifold pressure. This work serves as an exploratory effort to down select conditions and provide initial fuel properties of interest for a secondary study to explore fuel property specific effects on fuel-wall interaction and SPI propensity. Significant findings from this initial operating condition and fuel property exploratory work are: 1. reduced engine operating coolant and lubricant temperatures, along with 2. retarded injection timings were required to increase SPI propensity. Moreover, at these conditions some fuel specific effects were also observed; specifically, increased ethanol content increased measured dye–wall (i.e., fuel–wall) interaction. However, despite increased dye–wall interaction, the increased volatility of the ethanol containing fuels also reduced the estimated fuel retention in the top-ring zone and associated measured SPI propensity. Thus, the findings of this unique approach to explore relationships between fuel-wall impingement and SPI highlight that SPI propensity is more directly proportional to retained fuel, and not simply fuel–wall impingement. Furthermore, fuel retention was found to be directly influenced by complex fuel property and engine operating condition relationships. Either retarded injection timings and/or increased fuel volatility increased fuel wall-impingement, while less volatile fuels and/or reduced coolant temperatures increased fuel retention. Therefore, for a given operating condition, the data highlights that greater volatile fuels exhibit increased fuel wall impingement without increased fuel retention or SPI propensity, while less volatile fuels could exhibit reduced fuel-wall impingement but increased fuel retention and SPI propensity rates.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1981

The effects of trace impurities in coal-derived liquid fuels on deposition and accelerated high temperature corrosion of cast superalloys

The effects of trace metal impurities in coal-derived liquids on deposition, high temperature corrosion and fouling were examined. Alloys were burner rig tested from 800 to 1100 C and corrosion was evaluated as a function of potential impurities. Actual and doped fuel test were used to define an empirical life prediction equation. An evaluation of inhibitors to reduce or eliminate accelerated corrosion was made. Barium and strontium were found to limit attack. Intermittent application of the inhibitors or silicon additions were found to be effective techniques for controlling deposition without losing the inhibitor benefits. A computer program was used to predict the dew points and compositions of deposits. These predictions were confirmed in deposition test. The potential for such deposits to plug cooling holes of turbine airfoils was evaluated. Tests indicated that, while a potential problem exists, it strongly depended on minor impurity variations.

Lowell, C. E.↗
DOE OSTI2022

Sooting tendencies of terpenes and hydrogenated terpenes as sustainable transportation biofuels

Terpenes are a diverse group of molecules that are synthesized by plants and microorganisms through combining units of isoprene (2-methyl-1,3-butadiene). They typically contain rings and methyl branches, which gives them high energy densities and low freezing points and makes them appealing candidates for sustainable transportation biofuels. Between the original biosynthesis and upgrading options such as hydrogenation, they have a large degree of freedom of structures, e.g., different carbon skeletons, positions of double bonds, and functional groups. Therefore, structure-property data is needed to downselect potential fuel candidates. Here, we measured the sooting tendencies of 17 C10 monoterpenes and 7 of their hydrogenated analogues. The hydrogenated compounds were custom synthesized, so the quantities were too small for conventional smoke point measurements. Thus, the sooting tendencies were quantified with yield sooting index (YSI), which is based on the soot yield in a fuel-doped non-premixed methane flame. Derived smoke points (DSPs) were estimated from a correlation between YSI and smoke point for other hydrocarbons. The YSI of terpenes and their derivatives varies widely from 85.6 to 248.5. The YSI follows the trend: terpenes > dihydroterpenes > tetrahydroterpenes. The DSPs of all the tetrahydroterpenes and some dihydroterpenes are higher than that of a Jet-A fuel sample, suggesting that they offer soot reduction benefits. Further, the YSIs depend strongly on molecular structure; for example, α-pinene and β-pinene have identical carbon skeletons and differ only in the position of one carbon-carbon double bond, but the YSI of α-pinene is 34% higher than that of β-pinene. Detailed decomposition analysis via density functional theory (DFT) suggests that compared with β-pinene, α-pinene requires fewer steps to form the first aromatic ring and the process is more thermodynamically favorable. The YSI difference between the pinenes is mainly affected by the identity of the products from the dominant decomposition pathways.

09 BIOMASS FUELS↗
DOE OSTI2021

Amines have lower sooting tendencies than analogous alkanes, alcohols, and ethers

While the sooting tendencies of regular hydrocarbons, oxygenates, and complex fuel mixtures have been well-studied, far less research has been devoted to analyzing the influence of fuel-nitrogen on soot formation. The effect of nitrogen on soot formation becomes relevant for diesel fuels with nitrogen-containing additives, as well as biomass or biomass-derived fuels, which can contain up to 30% nitrogen-containing compounds by dry weight. To begin closing these gaps in the literature, the sooting tendencies of 14 C4 and C6 amines were measured. Sooting tendencies were quantified by re-scaling relative soot concentrations measured in fuel-doped methane flames into Yield Sooting Indices (YSI). The relative soot concentrations were measured with line-of-sight spectral radiance, and validation experiments confirmed that the presence of nitrogen in the test compounds did not interfere with this diagnostic. All of these amines had lower sooting tendencies than the structurally analogous hydrocarbons and oxygenates. The sooting tendencies of amine isomers with the same chemical formula varied significantly. Secondary amines with linear substituents were found to offer the lowest sooting propensity, while primary amines with branched substituents were observed to yield the largest sooting tendencies. In conclusion, the relationship between sooting propensity and chemical structure of the amines hints at the complex nature of soot formation, and highlights an interesting and unexplored area of combustion chemistry for further studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Thermal-barrier coatings for utility gas turbines

The potential of thermal barrier coatings for use in utility gas turbines was assessed. Pressurized passage and ambient pressure doped fuel burner rig tests revealed that thermal barrier coatings are not resistant to dirty combustion environments. However, present thermal barrier coatings, such as duplex partially stabilized zirconia and duplex Ca2SiO4 have ample resistance to the thermo-mechanical stress and temperature levels anticipated for heavy duty gas turbines firing clean fuel as revealed by clean fuel pressurized passage and ambient pressure burner rig tests. Thus, it is appropriate to evaluate such coatings on blades, vanes and combustors in the field. However, such field tests should be backed up with adequate effort in the areas of coating application technology and design analysis so that the field tests yield unequivocal results.

Levine, S. R.↗
DOE OSTI2020

Mn-doped oxide nuclear fuel

A nuclear fuel includes uranium(IV) oxide (UO2) and manganese (Mn) as a dopant. The Mn dopant may be present in the fuel in an amount up to the solubility limit for Mn under a given set of conditions, for example, about 0.01 wt % to about 1 wt %. The nuclear fuel is substantially free of aluminum (Al). The nuclear fuel exhibits enhanced grain size development during sintering temperatures as low at 1400 K due to an increase in uranium sub-lattice vacancies induced by dissolution of the Mn dopant at interstitial defect sites. The Mn-doped nuclear fuel exhibits improved grain sizes at lower temperatures compared to Cr-, Al-, and undoped UO2, and therefore desirably exhibits lower fission gas release and higher plasticity, reducing the chances of fuel rod failure.

Cooper, Michael William Donald↗
DOE OSTI2020

Grand potential sintering simulations of doped UO 2 accident-tolerant fuel concepts

Chromium-doped UO is a widely-studied near-term deployable accident-tolerant fuel concept because it results in a dense, large-grain structure that increases the fuel resistance to densification, swelling, and fission gas release. A new charged-interstitial mechanism was recently proposed to describe the behavior of dopants like chromium in sintered UO 2 . Based on that mechanism, manganese was suggested as an even stronger dopant than chromium. In the current work we use mesoscale sintering simulations in an effort to validate the new mechanism. We compare the relative behavior of Cr-doped and undoped UO 2 against experimental data in the literature. We also make predictions of the relative behavior of Mn-doped UO 2 . Simulations are done using the phase field-based grand potential sintering model. Dopants have two effects on sintered UO 2 . They marginally increase the densification rate and greatly increase the average grain size. Both of these effects are individually tested in small-scale simulations. Then large 3D sintering simulations are used to test the combined behavior of both effects. The results for the densification rate simulations are consistent with experiments for Cr-doped fuels. However, we note the grain growth rates are lower than what is found in the literature for Cr-doped fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Documenting Development of Processing Parameters for Fabrication of Doped and Undoped Fuel Pellets (Summary Report)

Early FY20 restructuring of the TREAT work package FT-20LA02020608 Enriched Fuel Fabrication for Safety Testing, and associated deliverables necessitated the rescoping of existing LANL deliverables. This rescoped carryover report summarizes work to date on doped and undpoped fuel pellet fabrication development of proceeding parameters. This summary also includes a status update of intended research activities that fall under the activity associated with this work package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1982

Gas turbine critical research and advanced technology (CRT) support project

The technical progress to provide a critical technology base for utility gas turbine systems capable of burning coal-derived fuels is summarized. Project tasks include the following: (1) combustion - to investigate the combustion of coal-derived fuels and the conversion of fuel-bound nitrogen to NOx; (2) materials - to understand and prevent the hot corrosion of turbine hot section materials; and (3) system studies - to integrate and guide the technological efforts. Technical accomplishments include: an extension of flame tube combustion testing of propane - Toluene Fuel Mixtures to vary H2 content from 9 to 18 percent by weight and the comparison of results with that predicted from a NASA Lewis General Chemical Kinetics Computer Code; the design and fabrication of combustor sector test section to test current and advanced combustor concepts; Testing of Catalytic combustors with residual and coal-derived liquid fuels; testing of high strength super alloys to evaluate their resistance to potential fuel impurities using doped clean fuels and coal-derived liquids; and the testing and evaluation of thermal barrier coatings and bond coatings on conventional turbine materials.

Furman, E. R.↗
NASA NTRS1989

NOx formation from the combustion of monodisperse n-heptane sprays doped with fuel-nitrogen additives

A series of experiments with simulated synthetic fuels were conducted in order to investigate the effect of droplet size on the conversion of fuel-nitrogen to NOx. Pyridine and pyrrole were added to n-heptane as nitrogen-containing additives and burned as monodisperse fuel droplets under various operating conditions in a spray combustion facility. The experimental results indicate that under stoichiometric and fuel-rich conditions, reducing the droplet size increases the efficiency of fuel-N conversion to NOx. This observation is associated with improved oxidation of the pyrolysis fragments of the additive by better oxygen penetration through the droplet flame zone. The dominant reactions by which fuel-N is transformed to NOx were also considered analytically by a premixed laminar flame code. The calculations are compared to the small droplet size results.

Sarv, Hamid↗
DOE OSTI2025

UO2 microstructural evolutions induced by Ni, Mo, and W dopants for intentional forensics

The concept of tagging nuclear fuel with a chemical barcode to enable forensics analysis across the nuclear fuel cycle is an area of active investigation, particularly to ensure fabrication viability without disrupting current fuel performance. This study explored the feasibility of using Ni, Mo, and W isotopic double-spikes as dopants in UO2 fuel from the perspective of fuel fabrication. Doped UO2 pellets were produced using conventional fuel fabrication processes, including powder mixing, sieving, pressing, and sintering in a reductive atmosphere. Two composition levels, 100 and 1000 ppm, were evaluated for each dopant element with isotopic double-spike configurations. For the Ni system, additional dopant concentrations of 250 and 500 ppm were produced with nonperturbed isotopic ratios. The results demonstrated that successful incorporation of Ni, Mo, and W double-spikes into UO2 pellets occurred with minimal shift in final density or dopant loss during pellet fabrication. Isotopic analysis confirmed the presence of the double-spike signature even when diluted with natural isotopic material in ratio of 1:5 in the fabrication process. Microstructural examinations revealed different impacts on grain size compared with undoped UO2. This study showed that Ni incorporation up to ∼500 ppm promoted moderate grain growth, whereas the Mo and W systems caused grain size reduction at all concentrations. Changes in the UO2 lattice parameter as a function of composition were detected exclusively for Ni up to 500 ppm, indicating that the Ni solid solution was the main factor for the observed grain growth. Insoluble (Mo and W) or supersaturated (Ni > 500 ppm) conditions produced grain size reduction. The Ni-doped pellets in the solution range resulted in a final microstructure within fuel specifications, demonstrating its potential benefits of employing complex dopant systems for potential nuclear forensic applications.

36 MATERIALS SCIENCE↗