Search NASA⌕ Search

SEARCH · Search NASA

Results for “Energy dependence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Energy-dependent and Energy-integrated Two-moment General-relativistic Neutrino Transport Simulations of a Hypermassive Neutron Star

Abstract We compare two-moment-based energy-dependent and three variants of energy-integrated neutrino transport general-relativistic magnetohydrodynamics simulations of a hypermassive neutron star. To study the impacts due to the choice of the neutrino transport schemes, we perform simulations with the same setups and input neutrino microphysics. We show that the main differences between energy-dependent and energy-integrated neutrino transport are found in the disk and ejecta properties, as well as in the neutrino signals. The properties of the disk surrounding the neutron star and the ejecta in energy-dependent transport are very different from the ones obtained using energy-integrated schemes. Specifically, in the energy-dependent case, the disk is more neutron-rich at early times and becomes geometrically thicker at later times. In addition, the ejecta is more massive and, on average, more neutron-rich in the energy-dependent simulations. Moreover, the average neutrino energies and luminosities are about 30% higher. Energy-dependent neutrino transport is necessary if one wants to better model the neutrino signals and matter outflows from neutron star merger remnants via numerical simulations.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2016

Energy Dependence of Fission Product Yields from {sup 235}U, {sup 238}U and {sup 239}Pu for Incident Neutron Energies Between 0.5 and 14.8 MeV

Fission Product Yields (FPY) have historically been one of the most observable features of the fission process. They are known to have strong variations that are dependent on the fissioning species, the excitation energy, and the angular momentum of the compound system. However, consistent and systematic studies of the variation of these FPY with energy have proved challenging. This is caused primarily by the nature of the experiments that have traditionally relied on radiochemical procedures to isolate specific fission products. Although radiochemical procedures exist that can isolate all products, each element presents specific challenges and introduces varying degrees of systematic errors that can make inter-comparison of FPY uncertain. Although of high importance in fields such as nuclear forensics and Stockpile Stewardship, accurate information about the energy dependence of neutron induced FPY are sparse, due primarily to the lack of suitable monoenergetic neutron sources. There is a clear need for improved data, and to address this issue, a collaboration was formed between Los Alamos National Laboratory (LANL), Lawrence Livermore National Laboratory (LLNL) and the Triangle Universities Nuclear Laboratory (TUNL) to measure the energy dependence of FPY for {sup 235}U, {sup 238}U and {sup 239}Pu. The measurements have been performed at TUNL, using a 10 MV Tandem Van de Graaff accelerator to produce monoenergetic neutrons at energies between 0.6 MeV to 14.8 MeV through a variety of reactions. The measurements have utilized a dual-fission chamber, with thin (10-100 μg/cm2) reference foils of similar material to a thick (100-400 mg) activation target held in the center between the chambers. This method allows for the accurate determination of the number of fissions that occurred in the thick target without requiring knowledge of the fission cross section or neutron fluence on target. Following activation, the thick target was removed from the dual-fission chamber and gamma-ray counted using shielded HPGe detectors for a period of 1-2 months to determine the yield of various fission products. To the extent possible all irradiation and counting procedures were kept the same to minimize sources of systematic errors. FPY have been determined at incident neutron energies of 0.6, 1.4, 2.4, 3.5, 4.6, 5.5, 8.9 and 14.8 MeV.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2019

Collision system and beam energy dependence of anisotropic flow fluctuations

New measurements of elliptic flow from two- and four-particle correlations are used to investigate flow fluctuations in collisions of U+U at √ s NN = 193 GeV, Cu+Au at √ s NN = 200 GeV and Au+Au at several beam energies. These measurements highlight the dependence of these fluctuations on the event shape, system size and beam energy and indicate a dominant role for initial-state-driven fluctuations. These measurements could provide further constraints for initial-state models, as well as for precision extraction of the temperature-dependent specific shear viscosity η/s( T ).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2018

Isolation of Physiologically Active Thylakoids and Their Use in Energy-Dependent Protein Transport Assays

Chloroplasts are the organelles in green plants responsible for carrying out numerous essential metabolic pathways, most notably photosynthesis. Within the chloroplasts, the thylakoid membrane system houses all the photosynthetic pigments, reaction center complexes, and most of the electron carriers, and is responsible for light-dependent ATP synthesis. Over 90% of chloroplast proteins are encoded in the nucleus, translated in the cytosol, and subsequently imported into the chloroplast. Further protein transport into or across the thylakoid membrane utilizes one of four translocation pathways. Here, we describe a high-yield method for isolation of transport-competent thylakoids from peas (Pisum sativum), along with transport assays through the three energy-dependent cpTat, cpSec1, and cpSRP-mediated pathways. We report these methods enable experiments relating to thylakoid protein localization, transport energetics, and the mechanisms of protein translocation across biological membranes.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Band Energy Dependence of Defect Formation in the Topological Semimetal Cd3As2

Cadmium Arsenide (Cd3As2) is a prototypical Dirac semimetal that manifests topological properties in a 3D bulk material. In defect-free Cd3As2, the Fermi level lies at a minimum in the density of states at the Dirac point, but experimentally it forms with excess electron carriers and an elevated EF, thereby masking the topological features. To computationally study the self-doping of Cd3As2, we combine density functional theory (DFT) calculations for defect formation energies with quasi-particle self-consistent GW (QSGW) electronic structure calculations. We demonstrate an innate dependence of the point defect formation energies on carrier concentrations and use the QSGW calculated density of states to extrapolate formation energies to arbitrary electron concentrations. This approach allows the quantitative modeling of thermodynamic defect equilibria in topological semimetals and is used to predict how Cd3As2 growth conditions affect the position of EF relative to the Dirac point.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS↗
DOE OSTI2016

Beam Energy Dependence of the Third Harmonic of Azimuthal Correlations in Au+Au Collisions at RHIC

In this paper, we present results from a harmonic decomposition of two-particle azimuthal correlations measured with the STAR detector in Au + Au collisions for energies ranging from √sNN = 7.7 to 200 GeV. The third harmonic v$2\atop{3}${ 2 } = , where Φ1 - Φ2 is the angular difference in azimuth, is studied as a function of the pseudorapidity difference between particle pairs Δη = η1-η2 . Nonzero v$2\atop{3}${ 2 } is directly related to the previously observed large- Δη narrow- ΔΦ ridge correlations and has been shown in models to be sensitive to the existence of a low viscosity quark gluon plasma phase. For sufficiently central collisions, v$2\atop{3}${ 2 } persist down to an energy of 7.7 GeV, suggesting that quark gluon plasma may be created even in these low energy collisions. In peripheral collisions at these low energies, however, v$2\atop{3}${ 2 } is consistent with zero. Finally, when scaled by the pseudorapidity density of charged-particle multiplicity per participating nucleon pair, v$2\atop{3}${ 2 } for central collisions shows a minimum near √sNN = 20 GeV .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Free Energy Dependencies for Interfacial Electron Transfer from Tin-Doped Indium Oxide (ITO) to Molecular Photoredox Catalysts

John B. Goodenough proposed that interfacial electron transfer kinetics from main group metal oxides should be fundamentally different from that of transition metal oxides, an expectation that has not been widely tested. Herein, the kinetics for interfacial electron transfer from mesoporous transparent conductive oxide Tin-doped Indium Oxide (ITO) to four photoredox catalysts (PCs) were characterized in acetonitrile electrolytes. The photocatalysts had the form: [Ru(4,4ʹ-R 2 -2,2′-bipyridine) 2 (4,4ʹ-(PO 3 H 2 ) 2 -2,2′-bipyridine)] 2+ , where R was H, methoxy, tert -butyl, and Br. The impact of the surface binding group was characterized with [Ru(2,2′-bipyridine) 2 (4,4ʹ-(CO 2 H) 2 -bpy)] 2+ . The interfacial electron transfer reaction ITO(e − )∣PC + → ITO∣PC was quantified by nanosecond absorption spectroscopy as a function of the applied potential (and hence ‒Δ G °). Specific conditions of applied potential were identified where the kinetics were sensitive to the incident irradiance. A layer-by-layer method was used to insert ionic methylene bridge(s) between the PC and the oxide surface. Marcus-Gerischer analysis of the kinetic data indicates non-adiabatic interfacial electron transfer with total reorganization energies that increase when bridges were placed between the photocatalyst and the ITO surface.

Bangle, Rachel E.↗
DOE OSTI2017

Invariant-mass and fractional-energy dependence of inclusive production of dihadrons in e + e - annihilation at s = 10.58 GeV

The inclusive cross sections for dihadrons of charged pions and kaons ( e + e - → h h X ) in electron-positron annihilation are observed and reported on. They are obtained as a function of the total fractional energy and invariant mass for any di-hadron combination in the same hemisphere as defined by the thrust event-shape variable and its axis. Since same-hemisphere dihadrons can be assumed to originate predominantly from the same initial parton, di-hadron fragmentation functions are probed. Moreove, these di-hadron fragmentation functions are needed as an unpolarized baseline in order to quantitatively understand related spin-dependent measurements in other processes and to apply them to the extraction of quark transversity distribution functions in the nucleon. The di-hadron cross sections are obtained from a 655 fb - 1 data sample collected at or near the Υ ( 4 S ) resonance with the Belle detector at the KEKB asymmetric-energy e + e - collider.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2016

SU-F-T-52: Study of Energy Dependent Effect of Dosimetry Systems Used in Therapeutic Soft X-Ray Energy Range

Purpose: To investigate energy dependent effects of different dosimetry systems which can be used as in vivo dosimetry monitoring for intraoperative radiotherapy in therapeutic soft x-ray energy range. Methods: Three dosimetry systems were evaluated in therapeutic soft x-ray energy range: optically stimulated luminescent dosimeter (OSLD) nanoDots, radiochromic EBT2 and EBT3 films. The x-ray photons were produced by a Zeiss Intrabeam 50 kV x-ray radiotherapy system. Solid water and bolus slabs with different thicknesses were used in the process of irradiation. An aluminum filter set was used to measure HVLs of X-rays. Calibration curves were made at different depth of boluses. Results: Half Value Layers at depths of 0, 3, 10, and 20 mm of solid water were measured to represent the energy change versus depth, yielding 0.306, 0.482, 0.865 and 0.901 respectively and indicating nearly unchanged HVL beyond 1 cm depth. The responses of each system at different depths were normalized to the response at 2 cm depth. In film dosimetry, the response is calculated as optical density (OD). The results show that there is nearly the same energy dependence for EBT2 and EBT3. At a HVL of 0.482 mm Al, the relative responses of nanoDots and EBT3 are 0.85 ± 0.04 and 0.89 ± 0.03 compared to those at 0.901 mm Al HVL, respectively, indicating no obvious difference between those two systems within the measurement uncertainty. Conclusion: It was observed that the studied dosimeter response increases about 13% from the x-ray energy of 0.48 mm Al to 0.90 mm Al. Therefore, caution should be exercised in using an appropriate calibration curve, and x-ray beam hardening effect has to be taken into account.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2016

Energy dependent response of plastic scintillation detectors to photon radiation of low to medium energy

Purpose: Plastic scintillation detectors are promising candidates for the dosimetry of low- to medium-energy photons but quantitative knowledge of their energy response is a prerequisite for their correct use. The purpose of this study was to characterize the energy dependent response of small scintillation detectors (active volume <1 mm{sup 3}) made from the commonly used plastic scintillator BC400. Methods: Different detectors made from BC400 were calibrated at a number of radiation qualities ranging from 10 to 280 kV and at a {sup 60}Co beam. All calibrations were performed at the Physikalisch-Technische Bundesanstalt, the National Metrology Institute of Germany. The energy response in terms of air kerma, dose to water, and dose to the scintillator was determined. Conversion factors from air kerma to dose to water and to dose to the scintillator were derived from Monte Carlo simulations. In order to quantitatively describe the energy dependence, a semiempirical model known as unimolecular quenching or Birks’ formula was fitted to the data and from this the response to secondary electrons generated within the scintillator material BC400 was derived. Results: The detector energy response in terms of air kerma differs for different scintillator sizes and different detector casings. It is therefore necessary to take attenuation within the scintillator and in the casing into account when deriving the response in terms of dose to water from a calibration in terms of air kerma. The measured energy response in terms of dose to water for BC400 cannot be reproduced by the ratio of mean mass energy-absorption coefficients for polyvinyl toluene to water but shows evidence of quenching. The quenching parameter kB in Birks’ formula was determined to be kB = (12.3 ± 0.9) mg MeV{sup −1} cm{sup −2}. Conclusions: The energy response was quantified relative to the response to {sup 60}Co which is the common radiation quality for the calibration of therapy dosemeters. The observed energy dependence could be well explained with the assumption of ionization quenching as described by Birks’ formula. Plastic scintillation detectors should be calibrated at the same radiation quality that they will be used at and changes of the spectrum within the application need to be considered. The authors results can be used to evaluate the range of validity of a given calibration.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Energy Dependence in the Neutrino Scattering Data of MINERvA

As we prepare for lower neutrino energy beams where physics is highly energy-dependent, it is important to isolate factors that can contribute largely to these low energy neutrino experiments. The world of neutrino oscillation experiments uses a wide range of energies: from 0.7 GeV beam of T2K and MicroBooNE, 2 GeV beam of NOvA, to the 0.6 to 6.0 GeV beam produced by DUNE in the future. MINERvA’s data are currently the best place to test the upper end of the range for DUNE and can be extrapolated into both DUNE’s and NOvA’s oscillation maximum. The goal of the research is to constrain energy dependence in the neutrino scattering experiment using data from MINERvA and then determine what factors contribute to the observed energy dependence. The research is divided into two parts. First, I will analyze different theoretical models in different channels of interaction, such as the quasi-elastic and delta resonance channels, in terms of neutrino energy dependence. The goal is to study the models at the level of the structure functions, which emphasizes the W2 structure function (the C function for QE) dominates the MINERvA data, but the W3 is increasingly important for NOvA and DUNE. The second half of the research is data-driven and focuses on the different detectors and systematic effects. An experimental effect, the angle acceptance, is larger than the structure function effects. However, it is a detector geometry effect and is well measured and well modeled. Other effects such as the muon energy scale are small and localized. Additionally, the research will determine if the MINERvA GENIE model correctly predicts all of the energy dependence seen in the data, and identify the remaining unmodeled energy dependence between the MINERvA data and its best simulation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Energy Dependence Analysis of Neutrino-Nucleus Interactions in Scintillator for MINERvA

This thesis is on the intrinsic energy dependence in neutrino-nucleus interaction models, especially quasielastic scattering and 2p2h process, and the implications for understanding data from MINERvA, NOvA, and DUNE. Neutrino-nucleus interactions are modeled using fve structure functions, W1, W2, W3, W4 and W5, and each structure function contributes diferently to the energy dependence once it enters the cross-section calculations. The energy independent term in the calculations contains only W2 and the next lower order term (of the order 1/E) contains W3 also. In this thesis, we show that W2 is good enough to describe MINERvA data and energy dependence coming from the cross-section directly is small. However, W3 will be signifcant for lower energy experiments such as NOvA and DUNE (especially at and below the oscillation maximum). We have also developed a method to extract structure functions directly from MINERvA data though we find that systematic uncertainties present in the data are too big to successfully determine 1/E Term. In addition to this, we have applied muon angle cuts on MINERvA data and MC, which have their own energy dependent effects. An apparent energy dependent discrepancy comes from known shortcomings especially in the pion production model. Finally, because the energy dependence analysis has similarities to the low-$\nu$ method, we have evaluated discrepancies between the data and MC in light of diferent fux constraint techniques. The results suggest including MINERvA s low-$\nu$ method constraint is an improvement.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2016

SU-F-I-70: Investigation of Gafchromic EBT3 Film Energy Dependence Using Proton, Photon, and Electron Beams

Purpose: To investigate the energy dependence of Gafchromic EBT3 film over a range of clinically used proton, photon and electron energies. Methods: Proton beam energies of 117 and 204 MeV, corresponding respectively to ranges in water of 10 cm and 27 cm from a Mevion S250 double scatter system unit were used. Electron energies of 6 and 20 MeV and photon energies of 6 and 18 MV from a Varian Clinac 21EX Linac were used. Two pieces of film (5×5 cm{sup 2}) were irradiated sequentially for doses of 100, 500, and 1000 cGy for all energies and modalities. Films were placed on the central beam axis for a 10×10 cm{sup 2} field size in the middle of spread out Bragg peak (SOBP) for proton and in respective dmax for photon and electron energies. Films were scanned on a flatbed Epson Expression 10000 XL scanner on the central region of the scanning window using 48-bit, 300 dpi, and landscape orientation after 48 hours post-irradiation of film to account for optical density (OD) stabilization. Film analysis of the red channel was performed using ImageJ 1.48v (National Institutes of Health). Results: The energy dependency of EBT3 among all energies and modalities for all doses studied was small within measurement uncertainties (1σ = ± 4.1%). The mean net OD in red channel for films receiving the same dose in the same energy modality had standard deviations within 0.9% for photons, 4.9% for electrons and 1.8% for protons. It was observed that film pieces were activated during proton irradiation, e.g., 7 mR/hr at surface after 30 minutes of irradiation, lasting for 2 hours post irradiation. Conclusion: EBT3 energy dependency was evaluated for clinically used proton, photon, and electron energies. The film self-activation may have contributed to fog and negligible dose.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2016

Reproducing the observed energy-dependent structure of Earth's electron radiation belts during storm recovery with an event-specific diffusion model

Here, we present dynamic simulations of energy-dependent losses in the radiation belt “slot region” and the formation of the two-belt structure for the quiet days after the 1 March storm. The simulations combine radial diffusion with a realistic scattering model, based data-driven spatially and temporally resolved whistler-mode hiss wave observations from the Van Allen Probes satellites. The simulations reproduce Van Allen Probes observations for all energies and L shells (2–6) including (a) the strong energy dependence to the radiation belt dynamics (b) an energy-dependent outer boundary to the inner zone that extends to higher L shells at lower energies and (c) an “S-shaped” energy-dependent inner boundary to the outer zone that results from the competition between diffusive radial transport and losses. We find that the characteristic energy-dependent structure of the radiation belts and slot region is dynamic and can be formed gradually in ~15 days, although the “S shape” can also be reproduced by assuming equilibrium conditions. The highest-energy electrons (E > 300 keV) of the inner region of the outer belt (L ~ 4–5) also constantly decay, demonstrating that hiss wave scattering affects the outer belt during times of extended plasmasphere. Through these simulations, we explain the full structure in energy and L shell of the belts and the slot formation by hiss scattering during storm recovery. We show the power and complexity of looking dynamically at the effects over all energies and L shells and the need for using data-driven and event-specific conditions.

58 GEOSCIENCES↗
DOE OSTI2016

Sci-Sat AM: Radiation Dosimetry and Practical Therapy Solutions - 03: Energy dependence of a clinical probe-format calorimeter and its pertinence to absolute photon and electron beam dosimetry

Purpose: To evaluate the intrinsic and absorbed-dose energy dependence of a small-scale graphite calorimeter probe (GPC) developed for use as a routine clinical dosimeter. The influence of charge deposition on the response of the GPC was also assessed by performing absolute dosimetry in clinical linac-based electron beams. Methods: Intrinsic energy dependence was determined by performing constant-temperature calorimetry dose measurements in a water-equivalent solid phantom, under otherwise reference conditions, in five high-energy photon (63.5 < %dd(10){sub X} < 76.3), and five electron (2.3 cm < R{sub 50} < 8.3 cm) beams. Reference dosimetry was performed for all beams in question using an Exradin A19 ion chamber with a calibration traceable to national standards. The absorbed-dose component of the overall energy dependence was calculated using the EGSnrc egs-chamber user code. Results: A total of 72 measurements were performed with the GPC, resulting in a standard error on the mean absorbed dose of better than 0.3 % for all ten beams. For both the photon and electron beams, no statistically-significant energy dependence was observed experimentally. Peak-to-peak, variations in the relative response of the GPC across all beam qualities of a given radiation type were on the order of 1 %. No effects, either transient or permanent, were attributable to the charge deposited by the electron beams. Conclusions: The GPC’s apparent energy-independence, combined with its well-established linearity and dose rate independence, make it a potentially useful dosimetry system capable measuring photon and electron doses in absolute terms at the clinical level.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2020

A generalized forward fit for neutron detectors with energy-dependent response functions

To date, most analysis of neutron time-of-flight data from inertial confinement fusion experiments has focused on the relatively small range of energies corresponding to the primary neutrons from DD and DT fusion, and have therefore employed instrument response functions (IRF’s) corresponding to monoenergetic 2.45-MeV or 14.03-MeV neutrons. For analysis of time-of-flight signals corresponding to broader ranges of neutron energies, accurate treatment of the data requires the use of an energy-dependent IRF. Here, this work describes interpolation of the IRF for neutrons of arbitrary energy, construction of an energy-dependent IRF, and application of this IRF in a forward fit via matrix multiplication. As an example of the application of this method, an analysis of synthetic data relevant to TT fusion experiments at the Omega Laser Facility is discussed. This example is used to illustrate the differences between a forward fit that uses an energy-dependent IRF and a forward fit that uses a monoenergetic IRF. Use of the energy-dependent IRF is shown to result in accurate inference of the fit parameters of interest.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Probing the Boundary between Classical and Quantum Mechanics by Analyzing the Energy Dependence of Single-Electron Scattering Events at the Nanoscale

The relation between the energy-dependent particle and wave descriptions of electron–matter interactions on the nanoscale was analyzed by measuring the delocalization of an evanescent field from energy-filtered amplitude images of sample/vacuum interfaces with a special aberration-corrected electron microscope. The spatial field extension coincided with the energy-dependent self-coherence length of propagating wave packets that obeyed the time-dependent Schrödinger equation, and underwent a Goos–Hänchen shift. The findings support the view that wave packets are created by self-interferences during coherent–inelastic Coulomb interactions with a decoherence phase close to Δφ = 0.5 rad. Due to a strictly reciprocal dependence on energy, the wave packets shrink below atomic dimensions for electron energy losses beyond 1000 eV, and thus appear particle-like. Consequently, our observations inevitably include pulse-like wave propagations that stimulate structural dynamics in nanomaterials at any electron energy loss, which can be exploited to unravel time-dependent structure–function relationships on the nanoscale.

36 MATERIALS SCIENCE↗