SEARCH · Search NASA
Results for “FPU”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Yield stress and flow behavior of enzyme liquefied slurries from corn cobs and corn stover pellets
With the increase in population, the world will depend on renewable sources to meet the increasing energy needs. The use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to thresholds for energy demand while reducing greenhouse gases by 90% when compared with fossil fuels. However, limitations in feeding and flow within biorefineries is encountered when system plugging occurs due to biomass compaction and a high yield stress for slurries formed during its processing, thereby preventing transport of biomass materials between plant unit operations. In some cases, this leads to unexpected plant shutdowns increasing industrial operational costs. As an alternative, enzyme-assisted liquefaction for slurry creation from corn stover at solids loadings up to 30% is reported in this work. Two different kinds of biomass (pelleted corn stover and cobs) were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU or 3 FPU per gram of dry solids in 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a pre-defined fed-batch protocol over the first 5 hours until reaching 30% of solids loading. After 6, 24 and 96 hours, samples were taken and characterized with respect to their sugar composition, rheology and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both assessed enzymes. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU,Celluclast 1.5L) for corn cobs at 24 hours. Yield stress decreased when residence time increased with an enhanced fluidity noted for higher enzyme concentrations. A profile for 6, 24 and 96h of yield stress measurements is presented.
High Solids Loading Aqueous Slurry Formation of Corn Stover Before Pretreatment in a Fed-batch Bioreactor
With the increase on population the world will depend on renewable sources to meet the increasingly energy needs. Use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to achieve the threshold on energy demand while reducing greenhouse gases in 90% when compared with fossil fuels (Wang et al., 2007, 2012). However, the processing of biomass encounters limitations in feeding and flow within biorefineries due to the system plugging by compaction and slurry high yield stress, preventing transport of biomass materials and in some cases unexpected plant shutdowns that results in high operational costs (dos Santos et al., 2021; Ximenes et al., 2021). Different solutions for biomass handling and slurry formation from densified materials like pellets have been studied. Cellulosic biomass residues are typically processed in pretreatment reactors to which acid or base is added (Humbird et al., 2002). Other pretreatments such as liquid hot water (LHW) and steam explosion that act without the addition of chemicals use pressures above the saturation vapor of water, to disrupt biomass structure (Ruiz et al., 2021). Although these methods are widely known, the use of pretreatments like acid digestion and LHW present challenges like waste disposal and could be energy inefficient (Mosier et al., 2005). Alternatively other approaches like enzymatic liquefaction have been applied for biomass transformation into slurries with promising results and without the use of pretreatments (dos Santos et al., 2021). Nevertheless, enzymatic liquefaction implementation faces difficulties due to the recalcitrant properties of biomass, its variability, and the release of enzyme inhibitors. While it has been proven that chemical composition properties in biomass have effects on enzyme inhibition (Huang et al., 2022; Kim et al., 2011; Zhai et al., 2018), hindering the efficiency of the liquefaction, not ample research has been conducted in understanding the physical properties as particle size, porosity, water adsorption retention and their effect in the ability to form a slurry at high solids concentration (Yan et al., 2020). In order to improve lignocellulosic biomass handling and formation of biomass slurries, enzyme assisted liquefaction for slurry creation from corn stover at solids loadings up to 30% is reported in this work. Two different kinds of biomass (pelleted corn stover and cobs) were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU or 3 FPU per gram of dry solids in 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a predefined fed-batch protocol over the first 5 hours until reaching 30% of solids loading. After 6, 24 and 96 hours, samples were taken and characterized with respect to their sugar composition, rheology and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both assessed enzymes. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours. Yield stress decreased when residence time increased with an enhanced fluidity noted for higher enzyme concentrations. A profile for 6, 24 and 96h of yield stress measurements is presented.
Enzyme-assisted liquefaction for different fractions of corn stover pellets
With an increase in population, the world will depend on renewable sources to meet the increasing energy needs. The use of lignocellulosic biomass as a renewable source has been proven efficient for conversion to cellulosic ethanol and capable of contributing to thresholds for energy demand while reducing greenhouse gases by 90% when compared with fossil fuels. However, limitations in feeding and flow within biorefineries are encountered when system plugging occurs due to biomass compaction and a high yield stress for slurries formed during its processing. Furthermore, differences in the biomass source present a challenge to the continuity of operations and reliability in the process. This work explores enzyme-assisted liquefaction for solid loadings up to 30% as an alternative for the creation of slurry from two different types of biomass (pelleted corn stover and cobs) that were liquefied in a fed-batch process using commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids in a 10 mM sodium citrate buffer solution (pH 4.8). Pellets were fed into a 1 L stirred bioreactor according to a predefined fed-batch protocol during the first 5 hours until 30% solid loading was reached. After 6, 24 and 96 hours, samples were taken and characterized with respect to their composition, rheology, and water absorption. Successful slurry creation with dramatically reduced yield stress was achieved for corn stover for both enzymes assessed. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3 FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme. Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours. A profile for 6, 24 and 96h of yield stress measurements and sugar conversion is presented.
Liquefaction of different corn stover fractions assisted by enzyme-biomass deconstruction
Recalcitrant properties of different sources of lignocellulosic biomass represent challenges in materials processing within a biorefinery, as well as enzyme efficient deconstruction to fermentable sugars. Limitations include lignin derived enzyme inhibitors, enzyme inhibition by hydrolysis products, and resistance to mixing due to rheological properties of lignocellulosic particulates at high solids loadings. Consequently, we examined conditions that might be used to achieve liquid slurries (i.e., liquefaction) at solids loadings of 300 g/L before the material enters the biorefinery through a pretreatment step. This work explores enzyme-assisted liquefaction in a fed-batch process using the commercial enzymes Celluclast 1.5L or Ctec-2 at 1FPU/g or 3 FPU/g of dry solids, basis. Corn stover pellets were fed into a 1 L stirred bioreactor containing enzyme solution over a 5-hour period until reaching 30% solids loading (dry wgt / vol basis). After 6, 24 and 96 hours from the start of the run, samples were taken and characterized with respect to their sugar composition, rheology, water absorption and enzyme activity. Slurries with dramatically reduced yield stresses were achieved for corn stover. Yield stresses of 178±7 Pa (3 FPU, Celluclast 1.5L) and 79±6 Pa (3FPU, Ctec-2) were measured for corn stover at 24 hours, compared to 6,000 Pa for samples without enzyme.Yield stress was 155± 29 Pa (3FPU, Ctec-2) and 257 ± 72 Pa (1 FPU, Celluclast 1.5L) for corn cobs at 24 hours.A profile based on 6, 24 and 96h of yield stress measurements and sugar conversion is presented. Enzyme activity is measured and the impact of liquefaction on an integrated processing in a biorefinery operation is discussed.
New strategy for liquefying corn stover pellets
The movement of solid material into and between unit operations within a biorefinery is a bottleneck in reaching design capacity, with formation of biomass slurries needed to introduce feedstock. Corn stover slurries have been achieved from dilute acid, pretreated materials resulting in slurry concentrations of up to about 150 g/L, above which flowability is compromised. We report a new strategy to liquefy corn stover at higher solids concentration (300 g/L) by initially cooking it with the enzyme mimetic maleic acid at 40 mM and 150°C. This is followed by 6 h of enzymatic modification at 1 FPU (2.2 mg protein)/g solids, resulting in a yield stress of 171 Pa after 6 h and 58 Pa in 48 h compared to 6806 Pa for untreated stover. Mimetic treatment of corn stover pellets minimizes the inhibitory effect of xylo-oligomers on hydrolytic enzymes. Furthermore, this strategy allows for the delivery of solid lignocellulosic slurry into a pretreatment reactor by pumping, improving operability of a biorefinery.
Screening method for Enzyme-based liquefaction of corn stover pellets at high solids
Liquefaction of high solid loadings of unpretreated corn stover pellets has been demonstrated with rheology of the resulting slurries enabling mixing and movement within biorefinery bioreactors. However, some forms of pelleted stover do not readily liquefy, so it is important to screen out lots of unsuitable pellets before processing is initiated. This work reports a laboratory assay that rapidly assesses whether pellets have the potential for enzyme-based liquefaction at high solids loadings. Twenty-eight pelleted corn stover (harvested at the same time and location) were analyzed using 20 mL enzyme solutions (3 FPU cellulase/ g biomass) at 30 % w/v solids loading. Imaging together with measurement of reducing sugars were performed over 24-hours. Further, some samples formed concentrated slurries of 300 mg/mL (dry basis) in the small-scale assay, which was later confirmed in an agitated bioreactor. Also, the laboratory assay showed potential for optimizing enzyme formulations that could be employed for slurry formation.
Effect of pelleting on the enzymatic digestibility of corn stover
Pelleting of lignocellulosic biomass to improve its transportation, storage and handling impacts subsequent processing and conversion. Here, this work reports the role of high moisture pelleting in the enzymatic digestibility of corn stover prior to pretreatment, together with associated substrate characteristics. Pelleting increases the digestibility of unpretreated corn stover, from 8.2 to 15.5% glucan conversion, at 5% solid loading using 1 FPU Cellic® CTec2 per g solids. Compositional analysis indicates that loose and pelleted corn stover have similar non-dissolvable compositions, although their extractives are different. Enzymatic hydrolysis of corn stover after size reduction to normalize particle sizes and removal of extractives confirms that pelleting improves corn stover digestibility. Such differences may be explained by the decreased particle size, improved substrate accessibility, and hydrolysis of cross-linking structures induced by pelleting. These findings are useful for the development of processing schemes for sustainable and efficient use of lignocellulose.
Enhanced Softwood Cellulose Accessibility by H 3 PO 4 Pretreatment: High Sugar Yield without Compromising Lignin Integrity
Softwood lignocellulose is a potential feedstock for the production of biofuels and bioproducts. However, the highly cross-linked nature of softwood lignocellulose restricts enzyme access to its sugars. Thus, harsh pretreatment conditions (180–280 °C) and/or high enzyme loading are required to unlock sugars. These requirements negatively affect the economic viability of softwoods in biorefineries. Here we show that H 3 PO 4 pretreatment of pine and Douglas fir under a mild reaction temperature (50 °C) and atmospheric pressure enabled a high (~80%) glucan digestibility with low enzyme loading (5 filter paper units (FPU)/g glucan). The dissolution and regeneration of softwoods disrupted the hydrogen bonding between cellulose chains, thereby increasing the cellulose accessibility to cellulase (CAC) values by ~38-fold (from ~0.4 to 15 m 2 /g biomass). Examination of H 3 PO 4 -pretreated softwoods by cross-polarization/magic angle spin (CP/MAS), 13 C- nuclear magnetic resonance (NMR), and Fourier-transform infrared spectroscopy (FTIR) revealed that breaking of the orderly hydrogen bonding of crystalline cellulose caused the increase in CAC (higher than 11 m 2 /g biomass), which, in turn, was responsible for the high glucan digestibility of pretreated softwoods. The H 3 PO 4 pretreatment process was feedstock independent. Finally, 2D 13 C– 1 H heteronuclear single quantum coherence (HSQC) NMR showed that the lignin was depolymerized but not condensed; thus, the lignin can be available for producing high-value products.
Understanding the Influence of Water-Soluble Compounds from Unpretreated Corn Stover Pellets on Enzymatic Hydrolysis of Cellulose
Aqueous extractives are minor and non-structural compounds in biomass that can be extracted using solvents, while contributing significantly to lignocellulose characteristics. Yet their roles in enzyme-mediated processing of lignocellulosic biomass remain elusive. Here, we examine the composition and features of extractives derived from untreated pelleted corn stover as well as their effects on enzymatic hydrolysis. Unlike the observations described in previous reports, we find that water extractable material improves the enzymatic hydrolysis of extractive-free stover by 67% with a glucose yield increase from 12% to 20% with 6 FPU cellulase per g glucan, whereas the enzyme activities are diminished when using microcrystalline cellulose as a substrate. The different behavior of corn stover and microcrystalline cellulose is likely attributed to the presence of lignin, which may interact with inhibitory compounds such as phenolics, mitigating the detrimental impacts of soluble inhibitors or insoluble lignin or both. These findings advance our fundamental understanding of the intrinsic behavior of extractives and help to optimize the schemes for efficient and cost-competitive enzymatic conversion of lignocellulose.
CIGEN
CIGEN is a tool that finds input ranges that cause high compiler-induced numerical inconsistencies in numerical programs written in a compiled language. Numerical program behavior may diverge when they are compiled and ran differently. Many factors, such as different hardware architectures (for example, the x87 FPU with its 80-bit registers), different compilers, or different optimization flags may cause the results of floating-point computations to become inconsistent. This kind of inconsistencies are known as compiler-induced numerical inconsistencies. Given a program with floating-point inputs and an output,
Analytical Modeling of Biomass Transport and Feeding Systems
The processing of biomass solids in a biorefinery consists of pretreatment, enzyme hydrolysis / concurrent fermentation of sugars to ethanol, product recovery, and drying. Sustainable operation requires a front end that transforms wet solids into a pumpable slurry. Otherwise the biorefinery will suffer unscheduled shut-downs and inefficient operation due to solids that obstruct pumps and other equipment and resist mixing in a bioreactor. Downtime in pioneer biorefineries due to interruptions from materials handling problems has been 50% or more, leading to unsustainable manufacturing processes. This work addresses new technology, predictive computational models, and definition of operational conditions that result in formation of slurries of corn stover at up to 300 g/L using low enzyme loadings (1 to 3 FPU cellulase/g) before the biomass (corn stover) enters the pretreatment step. A team of researchers from Purdue University, Idaho National Laboratory (INL), Forest Concepts, AdvanceBio, Argonne National Laboratory, and DOE BETO have combined their knowledge in agricultural and biological engineering, bioprocess engineering, mechanical engineering, chemical engineering, agricultural economics, materials engineering and enzyme and microbial technology to address the challenge of making lignocellulose flow. This team effort has resulted in the development and validation of conditions that employ low levels of commercial enzyme in an agitated bioreactor to which corn stover pellets are added resulting in formation of slurries at high solids loadings, before pretreatment. This approach overcomes challenges caused by handling of dry, particulate biomass materials at the front end of the biorefinery. The subsequent materials handling issues cause obstruction at pumps, pipes and valves. Formation of high loadings slurries with low yield stress, as reported here, significantly decreases the potential for process interruption and enhances plant operability. Key advances in the knowledge of how slurry formation occurs is reported here and in recently published journal papers. We found that pellets are needed to achieve high solids loading, and that commercial enzymes are effective in forming slurries of corn stover particles from pellets that have not been pretreated. Our work has resulted in models that predict solids behavior for formation of compressed solids and pellets that in turn facilitate slurries made of high concentrations of corn stover particles. A computational model was developed that gives mechanistic insights into properties of particles and mixing process that gives the slurry rheology needed to facilitate pumping. Hence, the corn stover may be pumped into a pretreatment reactor in place of auguring in solids against high pressure which is a root cause of interruptions at the front end of a biorefinery. Subsequent mixing in enzyme and microbial bioreactors results in conversion of lignocellulose to sugars in a biorefinery in agitated bioreactors, with flows in and out of the vessels being less likely to be interrupted due to plugging or materials handling problems. The obtained data coupled to process models, techno-economic assessment (TEA) and Life Cycle Analysis (LCA) were used to assess whether this approach is practical. These results are based on a foundation of laboratory characterization and pilot runs. The NREL biochemical sugar model was utilized to carry out techno-economic analysis of enzyme catalyzed liquefaction followed by enzyme hydrolysis. The minimum sugar selling price was between 17.5 and 18.3 ¢/pound or about the same as calculated by the NREL model for dilute acid pretreatment followed by enzyme hydrolysis. Life cycle analysis (LCA) based on Argonne’s Greet Model showed the enzyme catalyzed route had the lowest greenhouse gas emissions of the three combinations studied (i.e., enzyme, enzyme mimetic, and enzyme + mimetic combined). GHG emissions for enzyme-based corn stover liquefaction step, alone, were about 21 g CO 2 -equivalent/kg of liquefied slurry. We believe this approach will further enhance operability of a pioneer biorefinery, and bring large-scale conversion of lignocellulosic biomass to low carbon footprint biofuels closer to implementation.
MIT Capstone Project Assignment 1 - Existing System Design
“FPU in 5”: The National Nuclear Security Administration (NNSA) and upper management at Lawrence Livermore National Lab (LLNL) have informally set a long-term goal of decreasing the development cycle of new systems to five years or less. The driver is to be able to respond to emerging situations which require new capabilities more quickly. There are numerous approaches to solve the problem, and any single improvement is likely insufficient. Our capstone project focuses on modernizing the design development processes, production development processes, and communication between design agencies (DAs) and production agencies (PAs) to decrease the timeline from conceptual study to first production unit. Our project’s system problem statement (SPS) is below: TO decrease the time from conceptual study to first production unit BY centralizing design development, production development, and information exchange USING digital engineering techniques.
(U) MIT Capstone Project Assignment 2: Proposed System Design
“First Production Unit (FPU) in 5”: The National Nuclear Security Administration (NNSA) and upper management at Lawrence Livermore National Lab (LLNL) have set a long-term goal of decreasing the development cycle of new systems to five years or less. The driver is to be able to respond to emerging situations which require new capabilities more quickly. There are numerous approaches to solve the problem, and any single improvement is likely insufficient. We analyzed a variety of possible solutions at varying levels of specificity as shown in Figure 1. We chose to focus our scope on the optimization of existing documentation processes because it is the least likely to add additional risk and can be accomplished with lower investment than other potential solutions.
How does pelleting alter the enzymatic digestibility of corn stover?
Pelleting of lignocellulosic biomass facilitates its transportation, storage and handling and offers opportunities to improve the enzymatic digestibility of pelleted biomass. Here, we report the impact of pelleting on the enzymatic digestibility of corn stover prior to pretreatment and associated substrate characteristics. Pelleting almost doubles the digestibility of unpretreated corn stover, from 8.2 to 15.5% glucan conversion, at 5% solid loading using 1 FPU Cellic CTec2 per g solids. Compositional analysis indicates that loose and pelleted corn stover have similar non-dissolvable compositions, although their extractives are slightly different. Enzymatic hydrolysis of washed corn stover after size reduction to normalize particle sizes and removal of extractives confirms that pelleting improves corn stover digestibility. Such differences may be explained by the decreased particle size, increased specific surface area, improved cellulose accessibility, and reduction of the polymer length of cellulose induced by pelleting. These findings help to design processing schemes for sustainable and efficient use of lignocellulose.
Production and characterization of extracellular cellulases from a native strain of Trichoderma harzianum using wheat straw from the Mexicali valley as the carbon source. Producción y caracterización de celulasas Extracelulares a partir de cepa nativa de Trichoderma harzianum usando como fuente de Carbono paja de trigo del valle de Mexicali
The purpose of this study was to produce cellulase enzyme from a native strain Trichoderma harzianum, isolated from crop soil. Cellulase production was carried out by two different methods of fermentation, submerging and solid state fermentation. Mandels mineral medium was used as a source of nitrogen and ammonium sulfate. Dry and ground wheat straw was used in fermentation as a carbon source. Cellulase activity was determined using the 3,5-dinitrosalicylic acid (DNS) method. The results showed that wheat straw has the potential to be used as a substrate in the production of cellulases. Trichoderma harzianum showed enzymatic activity of 0.125 FPU / ml (filter paper units) and 1. 35 U / ml CMC (carboxymethyl cellulose units) by solid state fermentation (FSS) after 96 hours of fermentation. The optimum pH for the two substrates was determined by testing with citrate buffers (pH 4 to 6), phosphates (pH 6 to 7) and tris-HCL (pH 8 to 9). To determine the optimum temperature the range of 30 ° C to 80 ° C was investigated. Storage tests were performed every seven days over a period of 6 weeks. The optimum activity pH on paper and CMC was found to be 6. The optimum activity temperature is 70 ° C for PF and 80 ° C for CMC. El propósito de este estudio fue producir enzima celulasa a partir de una cepa nativa Trichoderma harzianum, aislada de suelo de cultivo. La producción de celulasa se realizó por dos métodos diferentes de fermentación, sumergida y fermentación en estado sólido. Se utilizó medio mineral Mandels y como fuentes de nitrógeno urea y sulfato de amonio. Se utilizó paja de trigo seca y molida en las fermentaciones como fuente de carbono. La actividad de la celulasa se determinó por medición de azúcares reductores al papel filtro y a la carboximetilcelulosa usando el método del ácido 3,5- dinitrosalicílico (DNS). Los resultados mostraron que la paja de trigo tiene el potencial para usarse como sustrato en la producción de celulasas. Trichoderma harzianum mostró actividad enzimática de 0.125 FPU/ml (unidades de papel filtro) y 1.35 U/ml a la CMC (unidades de carboximetilcelulosa) por fermentación en estado sólido (FSS) después de 96 horas de fermentación. El pH óptimo para los dos sustratos se determinó realizando pruebas con buffers de citratos (pH 4 a 6), de fosfatos (pH 6 a 7) y tris- HCL (pH 8 a 9). Para la determinación de la temperatura óptima se manejó el rango de 30°C a 80°C. Las pruebas de almacenamiento se realizaron cada siete días en un periodo de 6 semanas. Se encontró que el pH óptimo de actividad en papel y CMC es de 6. La temperatura óptima de actividad es de 70°C para PF y de 80°C para CMC.