Results for “HiCAM”

To meet the future demand of the commercial aircraft market, composite aircraft manufacturing rates must significantly increase. NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses this need to advance aircraft composite manufacturing technologies. Thermoplastic composites offer a promising solution to these manufacturing demands and present an opportunity for Northrop Grumman to bring the benefits of its Automated Stiffener Forming (ASF) technology to thermoplastic processing. Within HiCAM, Northrop Grumman is evolving the ASF technology for ply-by-ply, in-situ processing of thermoplastic composite materials. The modular process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for thermoplastics, heating technologies and roller compaction processes were investigated by manufacturing flat test coupons. These panels were evaluated by photo-microscopy, non-destructive inspection, and short beam shear tests and results were compared against baseline autoclave coupons. The results of the laminates fabricated via ASF are presented.

out of autoclave↗

NASA NTRSDate not supplied

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

thermoplastic composites↗

NASA NTRSDate not supplied

Improved Method for Increased-Rate Stitched Composites Manufacturing

Stitched composites, as defined herein, are created by stitching a dry preform, infusing the preform with resin and curing the resin. Stitched composites have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. However, conventional stitched composite structure production is very time and manual-labor intensive, and therefore is not conducive for high-rate production of commercial aircraft main structure. The National Aeronautics and Space Administration (NASA) Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project has the objective to increase the manufacturing rate for future composite aircraft. Stitched resin infused (SRI) composites are one of the technologies being considered under the HiCAM Project, but to be viable, production rates must be increased (i.e., production time reduced). Previous work has shown that it is possible to reduce the time required to stitch a dry composite preform, such as a skin with integral stiffeners, but the stitching process is a small portion of the total time required to produce a stitched preform. To significantly reduce overall stitched preform production time, a study was undertaken to examine a new stitching method that would yield time reduction in the pre- and post-stitching activities that include all portions of a stitched preform production with the exception of the actual stitching process. The new method resulted in significant reduction in production time, from 27% to 40%, while at the same time reducing the costs associated with fabricating a stitched preform by eliminating stations within the production line, simplifying tooling, reducing labor, and reducing consumables.

Stitching↗

NASA NTRSDate not supplied

Improved Method for Increased-Rate Stitched Composites Manufacturing

Stitched composites, as defined herein, are created by stitching a dry preform, infusing the preform with resin and curing the resin. Stitched composites have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. However, conventional stitched composite structure production is very time and manual-labor intensive, and therefore is not conducive for high-rate production of commercial aircraft main structure. The National Aeronautics and Space Administration (NASA) Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project has the objective to increase the manufacturing rate for future composite aircraft. Stitched resin infused (SRI) composites are one of the technologies being considered under the HiCAM Project, but to be viable, production rates must be increased (i.e., production time reduced). Previous work has shown that it is possible to reduce the time required to stitch a dry composite preform, such as a skin with integral stiffeners, but the stitching process is a small portion of the total time required to produce a stitched preform. To significantly reduce overall stitched preform production time, a study was undertaken to examine a new stitching method that would yield time reduction in the pre- and post-stitching activities that include all portions of a stitched preform production with the exception of the actual stitching process. The new method resulted in significant reduction in production time, from 27% to 40%, while at the same time reducing the costs associated with fabricating a stitched preform by eliminating stations within the production line, simplifying tooling, reducing labor, and reducing consumables.

Stitching↗

NASA NTRS2022

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

laser heating↗

NASA NTRSDate not supplied

Impact of Thermoplastic Composites: Testing and Modeling

Thermoplastic Composites (TPCs) are being increasingly considered for aerospace applications given their faster manufacturing cycles and lower cost. The NASA High-Rate Composite Aircraft Manufacturing (HiCAM) project aims to evaluate and mature thermoplastic manufacturing technologies to achieve a 4X – 6X increase in the production rate of Next Generation Single Aisle (NGSA) commercial aircraft. Within the purview of the NASA HiCAM project, this work investigates the response of thermoplastic composites under High Energy Dynamic Impact (HEDI) conditions. HEDI tests were conducted on panels fabricated with a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK) material system. A blunt metal projectile was chosen as the impactor which impacted the T700/LMPAEK panels over a range of impact velocities imparted by a gas gun test setup. As expected, lower velocity impacts caused the projectile to rebound, whereas higher velocity impacts resulted in the projectile penetrating the test panels. For the test cases in which the projectile rebounded, the predominant damage modes recorded with Ultrasonic (UT) scans included interlaminar delaminations which exhibited a “rotating fan” like structure when viewed in the through-thickness direction. Additionally, the dynamic deflection of the center point of the back face of the test panels and the velocity of the projectile was also measured during the test. Finite element models were developed to model a test case in which the projectile rebounded. These models were developed using LS-DYNA® wherein the primary objective was to evaluate the ability of the material model MAT299 to capture the dynamic response and damage modes in the T700/LMPAEK test panels. MAT299 is a Deformation Gradient Decomposition (DGD) based Continuum Damage Mechanics (CDM) material model. The interlaminar delaminations were modeled using the cohesive contact formulation available within LS-DYNA, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. The above-mentioned modeling methods have mostly been applied to thermoset composites and adapting them to TPCs involves addressing challenges associated with appropriately representing material behavior. Therefore, the proposed paper would discuss the systematic approach taken to adapt thermoset composites modeling practices for applications to TPCs, while appropriately addressing material behavior. The proposed paper would show that the predicted back face center point deflection correlated reasonably well with experimental data and the peak deflection was predicted to be within 5% of the experimental measurements. The projectile rebound velocity, while predicted to be higher than the experimental measurement, was within reasonable bounds. Additionally, it will be shown that the predicted delamination shapes were in reasonable agreement with experimental data.

Composite Materials↗

NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗

NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗

NASA NTRSDate not supplied

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

NASA NTRSDate not supplied

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

NASA NTRSDate not supplied

Design for Manufacturing of Structures with Automated Fiber Placement via Integration of Analysis and Process Planning

Under the Design for Manufacturing (DFM) task in the NASA HiCAM program, significant process has been made towards establishing a fully automated optimization process that spans the structural analysis, design, and manufacturing process planning for Automated Fiber Placement (AFP) structures. Previous efforts in this area established the data formats and mapping processes needed to exchange data between disciplines. The software tools used in the framework are HyperX (structural optimization), CAPP (process planning), and VCP (AFP path generation). The work has culminated with automation of data exchanges and an optimization process that drives the three software toward convergence. Within this framework, HyperX is used to generate mass-optimum composite designs which are iterated with VCP and CAPP to improve manufacturability of the designs. As the ply manufacturing process is adjusted by CAPP and VCP, HyperX continually re-assesses the structural integrity of the part and makes adjustments to the laminate as needed. For example, the position of fiber steering and tow overlaps/gaps can necessitate changes to the laminate design. Once the design converges, the end result is a stack of plies that meets both structural and manufacturing requirements. This paper presents the details of the framework and demonstrations the automated process on several parts with significant double-curvature.

HiCAM↗

NASA NTRSDate not supplied

Thermal Response of Thermoplastic Composite Tape During In-situ Consolidation Automated Fiber Placement Using a Laser Heat Source

Composite materials have tremendous potential in the design and manufacture of commercial aircraft due to their high strength-to-weight and stiffness-to-weight properties. However, the use of composite materials is currently limited by high cost and long manufacturing time. The National Aeronautics and Space Administration (NASA) initiated the Hi-rate Composite Aircraft Manufacturing (HiCAM) project to investigate promising composite processing technologies with a goal of vastly improving composite commercial aircraft manufacturing rate (4-6x faster than current production rates). Laser assisted automated fiber placement (AFP) of thermoplastics is a key technology that could increase speed of composite manufacturing, but the technology has not been fully developed. In-situ consolidation AFP of thermoplastics (ICAT) could reduce time and cost even further by eliminating the time and equipment required for post-consolidation. In this work, the thermal response of laser heated ICAT was investigated using forward looking infrared (FLIR) and embedded thermocouples (TCs) to better understand fusion between layers (autohesion). Detailed explanation of the algorithm to combine FLIR and TC data will be presented. In addition, the effect of robot speed on time above melting temperature was quantified.

Laser Heating↗