SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
"Fastener Design Manual", written to provide design engineers with single source assisting in choosing appropriate fasteners for their designs. Gives practical information on selection of fastener materials, platings, lubricants, galvanic corrosion, embrittlement by hydrogen, locking methods, inserts, washers, types and classes of threads, fatigue loading, and fastener torque.
This paper describes a modular packaging system for logistics that can be reconfigured into internal outfitting for a lunar outpost, including desks, chairs, partitions, cabinets, and radiation shielding. Logistics include clothes, equipment, food, and other consumables needed to sustain the crew for the duration of the mission. A significant mass penalty is required for the packaging and handling of logistics for re-supply of short to long-term space missions that must be brought out of the gravity well on a launch vehicle. Once the supplies have been exhausted, the packaging material is typically of no further use and is discarded. If a scheme can be developed that reuses the logistics packaging, the mass penalty can be reduced. In this research, a modular packaging system has been devised as a kit-of-parts that can be used for both handling logistics supplies, and then reconfigured into desks, chairs, partitions, cabinets, and radiation shielding. The system is derived from a standard International Space Station (ISS)-type Cargo Transfer Bag (CTB), using soft, unfoldable box-like containers with stiff metal inserts. The empty hydrogen-impregnated CTBs can be used as-is for cabinets, opened up for use as partitions, or draped over the habitat as layers of radiation shielding. Stiff metal inserts can be reconfigured into desks and other useful outfitting.
The structures assembly model (SAM) was installed, and wind tunnel systems were checked out. The first run, with hydrogen cooling and SAM inserted in the wind tunnel stream (M = 7.7, P sub TOTAL = 900 psia, T sub TOTAL = 2500 deg R), was accomplished. The condition of the SAM after the run was satisfactory, with no visible signs or data indications of overheating or overloading.
The underlying physical processes that liquid fuel sprays undergo in rotating detonation engines, particularly breakup and combustion, are not well understood nor are the coupling effects between the detonation and the spray. In this work, a single liquid jet of liquid fuel is inserted into a hydrogen-air RDC in order to study repetitive-one way coupled detonation interactions. High speed laser induced fluorescence of Jet-A at 300 kHz is used to visualize the dynamic processes inside the RDC for up to 10 ms per test. The employed imaging schemes allowed for unique insight into the spreading of liquid fuel in the azimuthal-axial directions via volumetric laser illumination. The Jet-A velocity field was estimated using OpenOpticalFlow and the impulse events observed colloquially agree with prior work on this test platform.
The underlying physical processes that liquid fuel sprays undergo in rotating detonation engines, particularly breakup and combustion, are not well understood nor are the coupling effects between the detonation and the spray. In this work, a single liquid jet of liquid fuel is inserted into a hydrogen-air RDC in order to study repetitive-one way coupled detonation interactions. High speed laser induced fluorescence of Jet-A at 300 kHz is used to visualize the dynamic processes inside the RDC for up to 10 ms per test. The employed imaging schemes allowed for unique insight into the spreading of liquid fuel in the azimuthal-axial directions via volumetric laser illumination. The Jet-A velocity field was estimated using OpenOpticalFlow and the impulse events observed colloquially agree with prior work on this test platform.
The arcjet assembly from a flight model system was modified with a new thoriated tungsten nozzle insert and has been tested with hydrogen-nitrogen mixtures simulating the decomposition products of ammonia and hydrazine. Arcjet power consumption ranged from 0.7 to 1.15 kW depending on low rate, input current, and mixture composition. At a nominal 1 kW power level the ammonia mixtures thrust efficiency was about 0.31 at specific impulse values ranging between 460 and 500 sec. Hydrazine mixtures gave similar thrust efficiencies at the same power level with specific impulse values between 395 and 430 sec. Large, spontaneous voltage mode changes were not observed once the thruster had passed a period of instability immediately following start up. This period of instability, and the startup at low pressure, were seen as major causes of constrictor damage during the tests.
The arcjet assembly from a flight model system was modified with a new thoriated tungsten nozzle insert and has been tested with hydrogen-nitrogen mixtures simulating the decomposition products of ammonia and hygrazine. Arcjet power consumption ranged from 0.7 to 1.15 kW depending on low rate, input current, and mixture composition. At a nominal 1 kW power level the ammonia mixtures thrust efficiency was about 0.31 at specific impulse values ranging between 460 and 500 sec. Hydrazine mixtures gave similar thrust efficiencies at the same power level with specific impulse values between 395 and 430 sec. Large, spontaneous voltage mode changes were not observed once the thruster had passed a period of instability immediately following start up. This period of instability, and the startup at low pressure, were seen as major causes of constrictor damage during the tests.
Considering the range of functions proteins perform, it is surprising they fold into a relatively small set of structures or "folds" that facilitate such function. One explanation is that only a minority were fit enough to emerge from Darwinian selection during the early evolution of life. Alternatively, perhaps only a fraction of all possible folds were trialed. Understanding proto-catalyst selection will aid understanding of the origins and early evolution of life. To investigate which explanation is correct, we study a protein evolved in vitro to bind ATP by Jack Szostak (Fig. 1). This protein adopts a fold which is absent from nature. We are testing whether this fold would have possessed the capability to evolve that would have been essential to survive natural selection on early Earth. Folds that couldn't improve their fitness and evolve to perform new functions would have been replaced by rivals that could. To determine whether the fold is evolvable, we are attempting to change the function of the protein by rationally redesigning to bind GTP. Two design strategies in the region of the nucleobase have been implemented to provide hydrogen bonding partners for the ligand i) an insertion ii) a MET to ASN mutation. Redesigns are being studied computationally at Ames Research Center including free energy of binding calculations. Binding affinities of promising redesigns are to be validated by experimental collaborators at ForteBio using Super Streptavidin Biosensors. If the fold is found to be non-evolvable, this may suggest that many structures were trialed, but the majority were pruned on the basis of their evolvability. Alternatively, if the fold is demonstrated to be evolvable, it would be difficult to explain its absence from nature without considering the possibility that the fold simply wasn't sampled on early Earth. This would not only further our understanding of the origins of life on Earth but also suggest a common phe-nomenon of proto-catalyst evolution.
Commercially available silicon-diode temperature sensors used to detect interfaces between hydrogen liquid and hydrogen vapor at steady-state saturation conditions. Sensors mounted at short intervals along rod to form rake-like array. Array inserted in tank with rod oriented vertically, where it senses level of liquid hydrogen to resolution equal to interval between sensors. Basic idea to measure voltage across sensor while supplying small electric current that heats sensor. Because vapor cools sensor less effectively than liquid does, sensor's steady-state temperature greater when sensor surrounded by vapor than when immersed in liquid. Voltage output decreases as temperature increases for silicon diodes. Thus, temperature (voltage) reading used to determine whether liquid level above or below sensor.
Hand-operated plug insertion valve seals an evacuated insulation system for upper stage liquid hydrogen tanks on the launch pad. It is light in weight, demountable, and permits evacuation of the system plus sealing after evacuation.
Damage by radiation healed rapidly. Feature provides continuous, rapid recovery of devices from degradation caused by hot electrons, photons, and ionizing radiation. Several candidate sites for palladium film catalysts, inserted during manufacture as integral parts of devices. Paladium films made by evaporation, sputtering, or chemical-vapor deposition. If additional storage required, thick layer of palladium plated on inside of package surrounding device. Hydrogen stored by exposing palladium to hydrogen gas just before package sealed hermetically.
Catalytic purifier removes oxygen from hydrogen feedlines just upstream of fuel-cell stack. Purifier consists of layer of platinum sandwiched between two sheets of porous polytetrafluoroethylene (PTFE). Platinum and PTFE elements stacked and ready for pressing. Purifier cut to size, pleated and inserted into convenient length of metal tubing. Purifier is 90 percent efficient in removing oxygen from gas stream containing 2 percent oxygen in hydrogen.
A stowage system was conceived that consists of collapsible, reconfigurable stowage bags, rigid polyethylene or metal inserts, stainless-steel hooks, flexible photovoltaic materials, and webbing curtains that provide power generation, thermal stabilization, impact resistance, work/sleeping surfaces, and radiation protection to spaceflight hardware and crew members. Providing materials to the Lunar surface is costly from both a mass and a volume standpoint. Most of the materials that will be transferred to other planets or celestial bodies will not be returned to the Earth. In developing a plan to reconfigure pressurized logistics modules, it was determined that there was a requirement to be able to utilize the interior volume of these modules and transform them from Logistics Modules to Storage/Living Quarters. Logistics-to-living must re-utilize stowage bags and the structures that support them to construct living spaces, partitions, furniture, protective shelters from solar particle events, galactic cosmic radiation, and workspaces. In addition to reusing these logistics items for development of the interior living spaces, these items could also be reused outside the habitable volumes to build berms that protect assets from secondary blast ejecta, to define pathways, to stabilize high traffic areas, to protect against dust contamination, to secure assets to mobility elements, to provide thermal protection, and to create other types of protective shelters for surface experiments. Unique features of this innovation include hydrogen-impregnated nano fibers encapsulated in a polyethelyne coating that act as radiation shielding, flexible solar collection cells that can be connected together with cells from other bags via the webbing walls to create a solar array, and the ability to reconfigure each bag to satisfy multiple needs.
NASA’s Space Launch System (SLS) Program is poised in 2021 to shift its focus to the launch site with the completion of its last major integrated hardware and software test. SLS is NASA’s evolvable super heavy-lift launch vehicle for deep space exploration. Using proven propulsion technologies, SLS will be the most powerful launch vehicle in the world. That capability translates not only into more mass and volume to destinations but also simplified payload design and mission operations and greater opportunity for mission success. These capabilities will be important for the Artemis program, NASA’s plan to return humans to the Moon to stay in a sustainable way in order to develop and test technologies and operations needed for human missions to Mars and other destinations. SLS will anchor the transportation leg of an innovative, sustainable program of lunar exploration with commercial and international partners as the first step of human exploration of deep space. While all major hardware and software efforts made significant progress in 2020 and 2021, the most visible was the Green Run test series of the Artemis I core stage conducted at NASA’s Stennis Space Center (SSC) on the B-2 test stand. The series validated core stage design, performance, workmanship, and readiness for shipment to NASA Kennedy Space Center (KSC) for final processing, integration and launch. The core stage provides the backbone for SLS’ main propulsion system, consisting of two five-segment solid rocket boosters and four RS-25 liquid hydrogen (LH2)/liquid oxygen (LOX) engines. SLS also includes an Interim Cryogenic Propulsion Stage (ICPS) that will insert the Orion crew spacecraft into a lunar trajectory.
Lifetime of hydrogen-maser bulb is increased by replacing beam stop plate with thick fluorinated ethylene-propylene (FEP) plug inserted in hole opposite beam entrance stem of bulb.
Before the Artemis I mission launches on its way around the Moon, the launch team at Kennedy Space Center and supporting teams across the country will begin the launch countdown about two days before liftoff. The launch countdown contains "L Minus” and "T Minus" times. "L minus" indicates how far away we are from liftoff in hours and minutes and does not include built-in holds. “T minus” time is a sequence of events that are built into the launch countdown where counting and holds are inserted. The 730,000 gallons of propellants that will be loaded into the rocket are liquid oxygen (LO2) and liquid hydrogen (LH2). Pauses in the countdown, or "holds," are built into the countdown to allow the launch team to target a precise launch window, and to provide a cushion of time for certain tasks and procedures without impacting the overall schedule. For the Artemis I countdown, planned built-in holds vary in length and occur at the following times: L-8 hours, 40 minutes, and L-40 minutes.
Because of the disintegration of LaNi5 as the lattice expands on absorbing hydrogen, a nickel hydrogen cell similar to a nickel cadmium cell was designed. The positive electrode is wrapped in a microporous separator and the leads are insulated. A negative conducting grid is inserted and welded to the top of the can into an open ended container which is then turned upside down and filled so that LiNa5 powder occupies all the space not used by the rest of the components. The bottom of the can is then welded on. A fill tube is located either on the bottom or on the top of the can. When welded shut, the cell is put into a pressure bomb and the lanthanum nickel is activated at about 1,000 pounds of hydrogen. Electrolytes are added to the cell as well as whatever amount of hydrogen precharge desired, and the cell is sealed. Advantages and disadvantages of the cell are discussed.
The effects of inserting a spherical conducting model, large in comparison with the Debye length, into a free streaming high-energy 1 kV) unmagnetized hydrogen plasma are investigated in order to measure energies and compositions directly relevant to solar wind and astrophysical plasma phenomena. Holding the incident plasma parameters constant, transverse profiles of the net Langmuir probe current are plotted at various locations downstream in the model wake and are divided into three regions (the shadow, transition, and boundary). Results attributable to the use of a high-energy plasma show that enhancements in the shadow exist at downstream locations where the Mach ratio is less than one, and turbulence exists in the transition region on the shadow edges and outside in the boundary region. In addition, a small current enhancement is found in the boundary and can be attributed to the plasma/model interaction. It is concluded that many similar features observed by spacecraft downstream from planetary bodies are relatively permanent and are due to the intrinsic nature of the interaction between the solar wind plasma and the obstacle.