Search NASA⌕ Search

SEARCH · Search NASA

Results for “Joint strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of die design on microstructure and mechanical joint strength in friction self-piercing riveted AA7055-T76 and AA7055-T76

In the present study, a unique friction self-piercing riveting (F-SPR) was applied to join high-strength, low-ductility aluminum alloy (AA) 7055-T76 and AA7055-T76 to mitigate a cracking issue. Also, the effect of die design on both joint formation and the mechanical joint performance were investigated. A crack-free joint was achieved when joining AA7055-T76 and AA7055-T76 by F-SPR. As the bottom diameter of the die increased, the mechanical interlocking distance initially increased then became almost saturated. At the same time, the solid-state bonding gradually disappeared, and the lap-shear fracture changed from bottom aluminum fracture to rivet pull-out with partial bottom aluminum fracture. The average maximum lap-shear joint strength of 11.57 kN and cross tension of 5.65 kN were achieved from the D2 die design owing to the combined contributions from high mechanical interlocking distance and good solid-state bonding at the joint interface. Ultrafine grain refinement was observed at the region next to the rivet shank outer surface and along the materials flow line between the top and bottom aluminum sheet in the rivet cavity. Further, because of the same joint-process parameters, the hardness profile at the joints made by different dies did not show obvious differences. As the distance from the base metal to the rivet outer surface decreased, frictional heat caused the hardness to initially decrease from 190 to 150 HV in the heat-affected zone. Hardness increased up to 175 HV in the thermomechanical affected zone (TMAZ-I) owing to large plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Friction Self-piercing Riveting Process for 3T Configuration of AA7075-AA7075-AA6022

Friction self-piercing riveting (F-SPR), as a solid-state joining process that generates frictional heat during the process, was utilized to join a 3 T configuration of low-ductility AA7075-AA7075-AA6022 sheets. A multi-step F-SPR process was employed to precisely control the mechanical interlocking and solid-state joining, ensuring a strong joint formation. With control of the plunge depth when the transition from rivet penetration to rivet flaring, two joining conditions were developed to assess mechanical joint integrity: one bearing deep penetration with a smaller interlock, and the other yielding a shallow penetration with a larger interlock. Both strategies met the criteria for a sound rivet joint. Customized lap shear tensile configurations were designed to assess the joint strength at interface between first and second layers, as well as between second and third layers. Both conditions demonstrated great joint strength between the first and second layers, while deeper penetration approach showed stronger solid-state joint, leading to improved joint strength between the second and third layers.

Wang, Tianzhao [ORNL] (ORCID:0000000315337602)↗
DOE OSTI2024

Exploring Failure of Adhesively-Bonded Joints with Different Void Sizes at the Same Void Volume Fraction through A Micro-scale Numerical Modeling

This paper studied the effects of void sizes on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicate that large void sizes with increased distances between them at the same void volume fraction can alleviate the reduced joint strength of a weaker adherend-adhesive interface caused by interfacial voids. However, this is not the case for an adherend-adhesive interface with the interfacial tensile strength being sufficiently higher than the adhesive strength, showing the negligible effect on the joint strength due to various void sizes and the amount of interfacial voids. This preliminary investigation provides insightful information for scaling up the void size in the macro-scale computational modeling of joints, and enhances the understanding of the micro-mechanical adhesion in adherend-adhesive interfaces with different levels of bonding.

Qiao, Yao↗
DOE OSTI2025

Current-Activated Reactive Ultrafast Joining (CARUJ)

We have demonstrated Current Activated Reactive Ultrafast Joining (CARUJ) as a novel approach for rapid fabrication of similar and dissimilar materials, such as ceramic-ceramic and ceramic-metal joint assemblies. The CARUJ technology utilizes resistive heating of carbon-based materials to apply localized heat at, (through or around) joint zones at rates of 10 1 -10 2 ˚C/min, enabling joining at time scales considerably shorter (several minutes as opposed to hours) than conventional approaches for similar systems. Herein, we present our findings while evaluating the CARUJ concept. Three methods of heat application were evaluated: (i) using carbon joule heating elements to apply heat directly through the joint interface; (ii) using flexible joule heating elements to locally apply heat around the assembly interface; and (iii) non-contact heating of the joint assembly using inductive power. Schemes (ii) and (iii) proved to be the most effective in producing mechanically sound reliable joints. We demonstrated single-step fabrication of dense SiC-SiC joints with a Si- SiC interface using minimal pressure (1–2 MPa) in under 30 minutes. Measured average joint strengths of about 15 MPa are initially achieved for joined bodies when tested in single lap offset (SLO) compressive shear, while tuning of the interfacial composition along with a reduction in interlayer thickness, results in improved joint strengths of approximately 43 MPa. We further demonstrated SiC-SiC joining using Active Brazing Alloys (ABAs) proof of concept joining of tubular geometries. The versatility of CARUJ is demonstrated by utilizing non-contact heating via induction, to join dissimilar materials systems of SiC, SS316 and MAX phase ceramics with ABA interlayers. The localized and rapid heat application realizes a versatile material joining technique that can be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scale-Up of Friction Self-piercing Riveting Process for Multi-material Joints

A single-class joining process known as “friction self-piercing riveting (F-SPR)” has been developed for joining various low-ductility lightweight materials on a laboratory scale. The frictional heat generated during the F-SPR process improved local ductility, resulting in crack-free joints and robust mechanical performance. This innovative joining technology was further advanced through the scale-up of the process using a new system with several key features (e.g., automatic rivet feeding and clamping system, vacuum system) toward industry readiness. The new integrated F-SPR systems were effectively demonstrated for joining different material combinations (e.g., carbon fiber composite to 7075 Al alloy, 7075 Al alloy to 7075 Al alloy, and 7075 Al alloy to casting Al Aural 5) with a unified technique. Crack-free joint with adequate mechanical interlocking resulted in good mechanical joint strength for each material combination. Then, the process was successfully scaled up by producing multiple joints without any cracks on larger CFC-Al and Al-Al components by the new integrated system, bringing it closer to industrial application.

Lim, Yong Chae [ORNL] (ORCID:0000000321773988)↗
DOE OSTI2025

Current activated reactive ultrafast joining (CARUJ) of silicon carbide

In this work we propose and demonstrate a novel approach for rapid fabrication of ceramic-ceramic joint assemblies, using sintered Silicon Carbide (SiC) as an initial example. Current Activated Reactive Ultrafast Joining (CARUJ) utilizes resistive heating of carbon-based materials to apply localized heat at or around the joint zone at heating rates of 101– 103 °C/min. CARUJ is used to fabricate SiC-SiC joints with a Si-SiC interface using minimal pressure (1–2 MPa) at time scales considerably shorter (several minutes opposed to hours) than conventional approaches for similar systems. The reaction of an interfacial precursor based on elemental silicon and carbon leads to in-situ SiC formation to produce a continuous and dense bond in a single step. Measured average joint strengths of roughly 15 MPa are achieved when tested in single lap offset (SLO) compressive shear. Optional additions of refractory metals such as molybdenum can be utilized to introduce secondary inclusions such as MoSi 2 within the joint interface. We further demonstrate SiC-SiC joining using Active Brazing Alloys (ABA) and proof of concept joining of tubular geometries. The localized and rapid heat application realizes a versatile material joining technique that could be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Using machine learning to jointly harness the strength of microscopic, fundamental-science driven and macroscopic, application-driven experiments

The PARADIGM project aims at accelerating progress in science by quantitatively answering the following question: What is the optimal combination of fundamental-science and application driven experiments to maximally reduce pertinent data uncertainties? Hence, we are bridging between microscopic experiments and data, and macroscopic simulations and experiments. Answering this question entails solving a high-dimensional and complex optimization problem which we solve with machine learning techniques.

LANSCE↗
DOE OSTI2025

Macro-level mechanical interlocking: A rapid joining approach for additively manufactured compression molded composite panels

Composite joining typically involves multiple steps, such as drilling and surface treatment, as part of the manufacturing process, which leads to low throughput and long cycle times. In the present study, we demonstrated a macro-level mechanical interlocking (MI) based, rapid joining technique to assemble additively manufactured compression molded (AMCM) panels, enabling the production of parts larger than the mold dimensions. Composite panels made of 20 wt% short carbon fiber reinforced acrylonitrile butadiene styrene (CF/ABS) were joined using MI features of various geometries, namely tree (TR), dovetail (Dov), rectangle 2 (Rect2), and rectangle 1 (Rect1), and their in-plane strength was evaluated. The resultant strength of the tested MI joints reached up to 74 % of the baseline tensile strength (i.e., the ‘no joint’ case). Observations from optical and scanning electron microscopy revealed inadequate polymer diffusion between the adherends, indicating that the joint strength was primarily derived from mechanical interlocking. Additionally, the fracture surfaces exhibited stress-whitening marks, which were characterized using differential scanning calorimetry (DSC). The increase in melting enthalpy suggested local stretching of polymer chains due to MI. Finite element analysis (FEA) indicated that the Rect1 MI feature, which generated the lowest stress concentration, outperformed the others in terms of joint strength, achieving 42 MPa. As a demonstration of the MI joining method, a battery box tray measuring 108 cm × 34 cm using a mold with an effective dimension of 36 cm × 34 cm successfully manufactured, resulting in a part with an area three times larger than the mold. In conclusion, this study presents a promising approach to improving composite joining techniques while minimizing production complexities.

In-plane joining↗
DOE OSTI2024

Microstructural Coarsening Kinetics and Mechanical Property Changes in Long-Term Aged Sn–Pb–Sb Solder Joints

Tin-lead-antimony (50Sn–47Pb–3Sb wt.%) soldered assemblies were mechanically tested approximately 30 years after initial production and found to have solder joints of reduced strength. The microstructure of this solder alloy exhibits a ternary eutectic structure with Sn-rich, Pb-rich, and SnSb phases. Accelerated aging was performed to evaluate solder microstructural coarsening and associated strength of laboratory solder joints to correlate these properties to the “naturally aged” solder joints. Isothermal aging was conducted at room temperature, 55, 70, 100, and 135 °C and aging times that ranged from 0.1 to 365 days. The coarsening kinetics of the Pb-rich phase were determined through optical microscopy and image analysis methods established in previous studies on binary Sn–Pb solder. A kinetic equation was developed with time exponent n of 0.43 and activation energy of 24000 J/mol, suggesting grain boundary diffusion or other fast diffusion pathways controlling the microstructural evolution. Compression testing and Vickers microhardness showed significant strength loss within the first 20–30 days after soldering; then, the microstructure and mechanical properties changed more slowly over long periods of time. Further, by combining accelerated aging data and the microstructure-based kinetics, strength predictions were made that match well with the properties of the actual soldered assemblies naturally aged for 30 years. However, aging at the highest temperature of 135 °C produced anomalous behavior suggesting that extraneous aging mechanisms are active. Therefore, data obtained at this temperature or higher should not be used. Overall, the combined microstructural and mechanical property methods used in this study confirmed that the observed reduction in strength of ~ 30-year-old solder joints can be accounted for by the microstructural coarsening that takes place during long-term solid-state aging.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Equivalent Properties of Interfacial Void Defects at the CFRTP-adhesive Interface and Their Detrimental Effects on the Bonding Performance of Metal-CFRTP Dissimilar Joints

This paper revealed the detrimental effects of micro-scale air interfacial voids on the debonding at the interface of carbon-fiber-reinforced polyphthalamide (CFRPPA) and thermoset adhesive, representing a weak adherend-adhesive interface, within a dissimilar joint made of an aluminum alloy and a CFRPPA. The reduced lap shear strength of the joint, due to different void area fractions at the CFRPPA-adhesive interface, can be computationally described by using equivalent interfacial properties in the modeling to avoid the explicit modeling of the micro-scale interfacial voids. Such equivalent interfacial properties (e.g., interfacial normal strength, etc.) was found to have a non-linear relationship with respect to interfacial void area fraction as well as lap shear strength. This work has practical applications by utilizing equivalent interfacial properties for the analytical and/or computational design(s) of adhesively bonded joints.

Qiao, Yao↗
DOE OSTI2026

Elucidating microstructural evolution and hardness variation across friction self-piercing riveted Al-7055 using synchrotron X-ray scattering and advanced microscopy techniques

Friction self-piercing riveting (FSPR) is a unique hybrid joining technique that combines the advantages of mechanical interlocking, frictional heat, and solid-state joining (if metallurgically compatible) to produce crack free joints in high strength and/or low-ductility alloys at room temperature. Here, in the current study, Al-7055 sheets were joined using FSPR for lightweight automotive applications and significant microhardness variations were observed across the joint cross-section. A detailed microstructural characterization at multiple length scales was carried out using advanced electron microscopy and X-ray scattering techniques to provide a fundamental understanding of the process-structure-property relationships. The relative contributions of microstructural characteristics at various length scales (i.e., grain size, dislocation density, solute concentration, precipitate nature) to strengthening were estimated using existent formulations (i.e., Hall-Petch, Taylor, precipitate bypass/shear equations) and correlated to the observed microhardness values across different regions. Small-angle X-ray scattering and scanning transmission electron microscopy revealed significant changes in the size and volume fraction of precipitate species, i.e., GP-I Zones, η′, and Mg/Zn solute co-clusters, depending on the process region. It was observed that the dissolution of the small η′/GP-I zones (T ∼ 150–200 °C) in the heat-affected zone were the key reason for the hardness drop. Further, it was shown that solid-solution, dislocation, grain size and solute co-cluster strengthening played a key role in the thermo-mechanically affected zone and grain-refined zone (GRZ). Finally, these observations were leveraged along with the Zener-Holloman relationship and grain size in the GRZ to estimate the peak joining temperature of the GRZ (∼ 350 °C) near the steel rivet.

aluminum 7xxx alloy↗
DOE OSTI2025

Fast-rate joining of thermoplastic composites using integrated additive manufacturing and compression molding process

The integration of additive manufacturing (AM) technology with compression molding (CM), has emerged as a high-performance composite manufacturing technology in recent years. In the AM-CM process, quickly deposited AM preform on a mold undergoes a rapid compaction cycle to fabricate structurally robust composite parts due to highly controlled fiber alignment (from AM) and reduced porosity (from CM). Currently, AMCM-based part size is limited by the size of the mold volume, thus posing a challenge to manufacture scalable parts. Here, this work focuses on joining techniques developed to enable fast rate joining of short fiber-reinforced thermoplastic composite parts using the AM-CM process. Acrylonitrile butadiene styrene resin reinforced with 20 wt% short carbon fiber composites was printed onto a flat mold and pressed under a hydraulic press. Fabricated panels were joined by the (a) mechanical impression at the joining interface and (b) over-molded continuous carbon fiber (CCF) sheet. Tensile tests were performed to characterize the joining strength of both mechanical impression-based joints and CCF over molded joints. Among the mechanical impression-based joints, a U-shape channel allowed the fibers to flow between two joint parts, and 280 % increased mechanical properties were observed. The continuous carbon fiber-based over molded joint CCF showed 350 % increase in tensile strength compared to the butt joints.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Control of wetting and uniformity via ZrSi x formation in ceramic-to-metal joints fabricated using Ag-Zr brazes

The deposition of a 2.0 µm SiO 2 film on the alumina surface in Kovar TM /94% alumina joints enables the formation of a silicide reaction layer on the alumina during brazing with 97Ag2Zr1Cu. Additionally, the average and standard deviation of joint thickness decrease from 50 to 15 and 29 to 4 µm, respectively compared to joints without added SiO 2 . Finally, the average failure stress of these braze joints was 45 MPa, while that of similar joints without added SiO 2 was 90 MPa. Sessile drop experiments of 98Ag2Zr on SiO 2 and 99.6% Al 2 O 3 substrates show that the braze wets and spreads to 3x its original area on SiO 2 with a wetting angle near 0°, but remains the same area on 99.6% Al 2 O 3 with a wetting angle of 106.6°. Focused-ion-beam scanning electron microscopy analysis of a cross-section of the 98Ag2Zr sessile drop on the SiO 2 substrate has shown that Zr reacts with SiO 2 to form Zr oxide and silicide layers. Scanning transmission electron microscopy diffraction and energy dispersive X-ray spectroscopy analysis indicate this silicide layer contains tetragonal Zr 5 Si 4 . In conclusion, analysis shows the silicide layer enhances wetting and joint uniformity while unreacted SiO 2 embrittles the joint and degrades strength.

alumina↗
DOE OSTI2026

An Experimental and Numerical Study of Plasma Treatment Effects on Adhesive Joints of Metals, CFRTPs, and Metal–CFRTP Combinations

This work investigates the effects of plasma surface treatment on both the local adherend–adhesive interfacial strength and the global lap shear strength (LSS) of adhesively-bonded joints composed of metals, CFRTPs, and metal-CFRTP combinations, using AA6061 and CFRPPA as representative examples. Experimental and computational results show that plasma treatment improved the ratio of CFRPPA–adhesive interfacial normal strength to adhesive tensile strength (sint,n/scri,t,adhesive) from 0.59–1.00 to 0.91–1.73, leading to an average 90% increase in LSS for CFRPPA-related joints. In contrast, the LSS and sint,n/scri,t,adhesive values of AA6061–AA6061 joints (>=2.27) remained nearly unchanged after plasma treatment. The enhanced joint bonding was further supported by post-failure surface morphologies from three-dimensional profilometry and simulations, showing a transition from dominant interfacial failure to mixed modes involving interfacial, cohesive, and slight fiber-peeling failures. The LSS evolution with respect to sint,n/scri,t,adhesive was numerically established until the saturation of the LSS of various joints, and the behavior of AA6061–CFRPPA T-joints with varying interfacial strengths was also modeled. This study highlights the importance of local interfacial bonding strength, rather than global LSS, for understanding and optimizing the mechanical performance of adhesively-bonded composite–metal and composite-composite structures via different surface modification strategies.

Qiao, Yao (ORCID:0000000265867604)↗
DOE OSTI2024

Innovative Joining Method for Hybrid Composites with Tailored Performance

In various industries, such as renewables and aerospace, the demand for carbon fiber is rapidly growing to meet the requirements of high-performance applications with optimized designs. Traditionally, these optimized designs have been limited to single-material composites due to process constraints. However, this study aims to explore the feasibility of transitioning between two different fiber types for pultrusion and filament winding processes, thereby enhancing design flexibility, and optimizing performance. This research introduces a novel method of hybrid reinforcement through splicing techniques. By employing a splicing method, fibers are merged prior to infusion, resulting in a transition of higher strength compared to traditional joints. Moreover, this technique enables the creation of composites with variable compositions, allowing for the selective placement of properties in a process previously characterized by static properties. The objective of this paper is to evaluate the mechanical properties of dry fiber splicing and its impact on the resulting composite material. Through comprehensive analysis, we aim to provide insights into the feasibility and advantages of employing this innovative splicing technique in composite manufacturing processes.

Guzorek, Steven↗
DOE OSTI2025

Porous Interlayers that Getter Surface-Segregating Species for Improved Silver Wetting, Adhesion, and Electrical Contact on Stainless Steel SOFC Components

Here, porous nickel interlayers or porous platinum interlayers were shown to promote the wetting, spreading, and adhesion of silver on alumina-forming ferritic stainless steel (AFFSS) and chromia-forming ferritic stainless steel (CFFSS). These interlayers resulted in dense, crack-free AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints that, after 300 h in 650 °C air, displayed shear strengths up to 70 MPa similar to, or larger than, those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. Similarly, after exposure to 25 cycles of (50 switches between) 12 h of 650 °C air and 12 h of 650 °C 4%H 2 –96%N 2 , AFFSS|Ag-Ni|CFFSS and AFFSS|Ag-Pt|CFFSS braze joints displayed shear strengths significantly larger than those of AFFSS|Ag-CuO|CFFSS or AFFSS|Ag|CFFSS joints subjected to identical treatment. In addition, nickel and platinum were found to chemically getter surface-segregating steel constituents, particularly Al from the AFFSS. As a result, Ag-Ni and Ag-Pt electrical contact resistances on AFFSS and CFFSS substrates were several orders of magnitude lower than those of conventional Ag-CuO reactive air brazes or Heraeus C8710 Ag contact pastes. Together, these results suggest that Ag-Pt and especially Ag-Ni may be useful for the fabrication of durable joints, seals, and/or electrical contacts in electrical/electrochemical devices exposed to high temperatures and/or variable oxygen partial pressure environments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Gas tungsten arc welding and post weld heat treatment effects on microstructure and mechanical property of castable nanostructured alloy steel

Here, this paper details the first study of castable nanostructured alloy (CNA) steel gas tungsten arc weldability and the post-weld heat treatment (PWHT) effects. Effects of welding heat input, thermal cycles, and PWHT on microstructures, microhardness distributions, room temperature tensile properties, and fracture characteristics are discussed. Results show that CNA steel exhibits excellent weldability (i.e., no indication of welding defects and reasonable tensile properties). The welded joint exhibited heterogeneous microstructures with δ-ferrite as well as large microhardness variation and fluctuation. The welded joint yield and ultimate tensile strengths were similar to those of the base metal, but the elongations decreased by 30 %. However, with normalization and tempering PWHT, the δ-ferrite was eliminated, microstructure was modified, hardness was unified, and joint ductility was restored. The study indicated that the CNA reduced-activation ferritic-martensitic steel owns excellent weldability, and PWHT is needed for the industrial application of welded structures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Testing and modeling of CLT-to-CLT joints made using hardwood dowels and screws with varying spacing

With the increasing popularity of mass timber, utilizing large-diameter wood screws and hardwood dowels can offer an easy and cost-efficient way to join structural elements. However, the existing research on hardwood dowels is limited to single fastener joints under monotonic loading. No research is available on the group effects of joints with multiple hardwood dowels. Here, this paper presents the results of 96 monotonic and cyclic single-shear plane CLT-to-CLT joint tests with hardwood dowels (Red Oak and Yellow Birch, 25.4 mm diameter) and self-tapping wood screws (8 mm diameter) in Grand-Fir CLT, where screws were inserted both perpendicular and at a 45-degree angle to the grain for comparison to hardwood dowels. The study evaluated the mechanical properties of the joints by changing fastener spacing. Mechanical properties such as yielding and peak strength, displacement, elastic and yielding stiffness, and ductility were evaluated. The results showed equal strength and stiffness properties for hardwood dowels comparable with large-diameter screws. Additionally, the hardwood dowel joints demonstrated moderate ductility properties. The strength and stiffness of the tested joints were compared with analytical equations found in the literature by considering the group action factor of the fasteners. Lastly, a nonlinear force-displacement model was presented and compared to the experimental results and analytical calculations, which gives the possibility to predict and optimize the mechanical behavior of hardwood dowel and screw joints with varying numbers and spacing between fasteners.

36 MATERIALS SCIENCE↗