Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIFT DISTRIBUTION - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Aerodynamic Rotor Design for a 25 MW Offshore Downwind Turbine

Continuously increasing offshore wind turbine scales require rotor designs that maximize power and performance. Downwind rotors offer advantages in lower mass due to reduced potential for tower strike, and is especially true at large scales, e.g., for a 25 MW turbine. In this study, three 25 MW downwind rotors, each with different prescribed lift coefficient distributions were designed (chord, geometry, and twist) and compared to maximize power production at unprecedented scales and Reynolds numbers, including a new approach to optimize rotor tilt and coning based on aeroelastic effects. To achieve this objective the design process was focused on achieving high power coefficients, while maximizing swept area and minimizing blade mass. Maximizing swept area was achieved by prescribing pre-cone and shaft tilt angles to ensure the aeroelastic orientation when the blades point upwards was nearly vertical at nearly rated conditions. Maximizing the power coefficient was achieved by prescribing axial induction factor and lift coefficient distributions which were then used as inputs for an inverse rotor design tool. The resulting rotors were then simulated to compare performance and subsequently optimized for minimum rotor mass. To achieve these goals, a high Reynolds number design space was developed using computational predictions as well as new empirical correlations for flatback airfoil drag and maximum lift. Within this design space, three rotors of small, medium and large chords were considered for clean airfoil conditions (effects of premature transition were also considered but did not significantly modify the design space). The results indicated that the medium chord design provided the best performance, producing the highest power in Region 2 from simulations while resulting in the lowest rotor mass, both of which support minimum LCOE. The methodology developed herein can be used for the design of other extreme-scale (upwind and downwind) turbines.

downwind rotors↗
DOE OSTI2024

On optimizing the sensor spacing for pressure measurements on wind turbine airfoils

This research article presents a robust approach to optimizing the layout of pressure sensors around an airfoil. A genetic algorithm and a sequential quadratic programming algorithm are employed to derive a sensor layout best suited to represent the expected pressure distribution and, thus, the lift force. The fact that both optimization routines converge to almost identical sensor layouts suggests that an optimum exists and is reached. By comparing against a cosine-spaced sensor layout, it is demonstrated that the underlying pressure distribution can be captured more accurately with the presented layout optimization approach. Conversely, a 39 %–55 % reduction in the number of sensors compared to cosine spacing is achievable without loss in lift prediction accuracy. Given these benefits, an optimized sensor layout improves the data quality, reduces unnecessary equipment and saves cost in experimental setups. While the optimization routine is demonstrated based on the generic example of the IEA 15 MW reference wind turbine, it is suitable for a wide range of applications requiring pressure measurements around airfoils.

17 WIND ENERGY↗
DOE OSTI2024

Hydrodynamic fluctuations near a Hopf bifurcation: Stochastic onset of vortex shedding behind a circular cylinder

Here, we investigate hydrodynamic fluctuations in the flow past a circular cylinder near the critical Reynolds number Re c for the onset of vortex shedding. Starting from the fluctuating Navier-Stokes equations, we perform a perturbation expansion around Re c to derive analytical expressions for the statistics of the fluctuating lift force. Molecular-level simulations using the direct simulation Monte Carlo method support the theoretical predictions of the lift power spectrum and amplitude distribution. Notably, we have been able to collect sufficient statistics at distances Re ⁡/ Re c – 1 = O ⁡(10 –3 ) from the instability that confirm the appearance of non-Gaussian fluctuations, and we observe that they are associated with intermittent vortex shedding. These results emphasize how unavoidable thermal-noise-induced fluctuations become dramatically amplified in the vicinity of oscillatory flow instabilities and that their onset is fundamentally stochastic.

42 ENGINEERING↗
DOE OSTI2020

Shear-induced lift force on spheres in a viscous linear shear flow at finite volume fractions

Several studies have shown a significant increase in drag on a distribution of solid spherical particles within a fluid with increasing particle volume fraction. As a result, many empirical drag laws accounting for the dependence on the Reynolds number and volume fraction can be found in the literature. This study investigates the possibility of a similar effect of the particle volume fraction on the mean hydrodynamic lift force on randomly distributed spherical particles in a linear shear flow. Particle-resolved direct numerical simulations are performed to evaluate the mean lift force, and the results are compared with the case of an isolated particle in a linear shear flow for the same Reynolds number and shear rate. The mean lift force acting on the particles appears to remain nearly the same as that on an isolated particle. However, due to the influence of neighboring particles, there is a substantial force variation in transverse directions on each individual particle, whose magnitude is comparable to the mean drag force. The distribution of drag force in a linear shear flow is shown to be nearly the same as in a uniform flow at the same volume fraction and Reynolds number. A simple stochastic model based on a Gaussian distribution is presented for the lift force variation, and its performance is compared to the prediction of the deterministic pairwise interaction extended point-particle model.

42 ENGINEERING↗
DOE OSTI2022

Resilient cooling through geothermal district energy system

Decarbonization and resilience to heat waves have recently become high priorities for building and district energy systems. Geothermal coupled district heating and cooling systems that operate a water loop near ground temperature gain increasing adoption to support decarbonization. In these systems, vapor-compression machines, distributed in the energy transfer stations, lift the temperature up or down to the needs of the particular building. In principle, these systems can provide low-power, free cooling from the geothermal bore field during heat waves when electricity is often scarce. However, the performance of such a resilience operation mode and its implication on the energy system configuration and the sizing of the bore field and HVAC equipment is not yet understood. Consequently, we are assessing their resilience, power use and design implications under a scenario of a heat wave on five working days during which chillers are switched off to reduce electrical consumption. Our analysis is based on high-fidelity, coupled dynamic models of district energy, building-side HVAC and actual control logic, with whole building energy simulation used to assess thermal conditions in a 2004 vintage multi-zone office building in Chicago, IL. The results show that relying only on waterside economizer cooling, the indoor thermal conditions can be maintained in a tolerable range for the majority of the building zones with half the electrical energy compared to standard chiller operation. Thermal comfort in the hottest zones can be further improved by oversizing the cooling coil. However, the waterside economizer has significant implications on the system configuration and sizing: The geothermal bore field needs to be sized about 30% larger than the upper limit of the range observed for conventional geothermal systems. Nevertheless, if a central chiller plant is added, the bore field can be downsized to the typical design range. The latter configuration still allows compressor-less cooling during the heat wave with peak power reduced by 60% compared to the standard design and chiller operation.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Verification of an improved equation-free projective integration method for neoclassical plasma-profile evolution in tokamak geometry

A brute-force, long-time gyrokinetic simulation of plasma profile evolution in magnetic fusion devices is not desirable due to large computational resource requirements and a possible accumulation of numerical error. The equation-free projective integration method of Keverekidis et al. [Commun. Math. Sci. 1(4), 715–762 (2003)] is one of the outstanding candidates in projecting micro-scale simulations to a longer timescale. However, its application to tokamak plasma has not been fruitful due to the appearance of spurious transient oscillations in the lifting process, which are present when the kinetic simulations are initialized with a simplified model distribution function and which make the kinetic simulations to deviate from the desired paths. In this work, a kinetically informed lifting algorithm is added to the equation-free projective integration method, which is then verified in the electrostatic gyrokinetic particle-in-cell code XGCa [R. Hager and C. S. Chang, Phys. Plasmas 23, 042503 (2016)] for a neoclassical ion heat transport problem with adiabatic electrons. This new lifting operator is demonstrated to control spurious transients, enabling an over four-times reduction in the overall computing time in the time-evolution of the ion temperature profile in an axisymmetric toroidal plasma. Further reduction in the computing time is found to be limited due to the stability properties of the linear least squares projective integrator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Weak-charge form-factor determination at the electron-ion collider

Determining the weak charge form factor, 𝐹 𝑊 ⁡(𝑄 2 ), of nuclei over a continuous range of momentum transfers, 0 ≲ 𝑄 2 ≲ 0.1 GeV 2 , is essential for mapping out the distribution of neutrons in nuclei. The neutron density distribution has significant implications for a broad range of areas, including studies of nuclear structure, neutron stars, and physics beyond the Standard Model. Currently, our knowledge of 𝐹 𝑊 ⁡(𝑄 2 ) comes primarily from fixed target experiments that measure the parity-violating asymmetry in coherent elastic electron-ion scattering. Fixed target experiments, such as CREX and PREX-1,2, have provided high-precision weak charge form factor extractions for the 48 Ca and 208 Pb nuclei, respectively. However, a major limitation of fixed target experiments is that they each provide data only at a single value of 𝑄 2 . With the proposed electron-ion collider (EIC) on the horizon, we explore its potential to impact the determination of the weak charge form factor. While it cannot compete with the precision of fixed target experiments, it can provide data over a wide and continuous range of 𝑄 2 values, and for a wide variety of nuclei. We show that with data corresponding to an integrated luminosity of ℒ ∼ 500/𝐴 fb −1 , where 𝐴 is the nucleus atomic weight, the EIC can significantly impact constraints by lifting degeneracies in theoretical models of the neutron density distribution. Ensuring EIC detector coverage at low 𝑄 2 and large negative pseudorapidities will be essential for such 𝐹 𝑊 ⁡(𝑄 2 ) measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Housing Energy Connection Project (Final Technical Report)

This project expanded existing medium-voltage distribution to 33 households, a daycare, a mechanical shop, irrigation pumps, and a sewer lift station, all of which previously received electric service from the local electric utility. As part of the project, automatic meter reading (AMR) and advanced metering infrastructure (AMI) was installed to allow the Tribe to set up its own electric metering like a utility. The primary objective of this project was to expand the Tribe-owned electrical distribution to provide highly reliable electrical service to these existing loads. The objective was successfully met after project completion. The project reduced high costs for electric energy previously supplied by the utility, by supplanting utility-supplied electric power with Tribe-generated electric power. The project gave the Tribe greater independence from traditional power sources and provided jobs for the community.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Raman studies of hydrogen trapped in As 4 O 6 ·2H 2 at high pressure and low temperature

In this work, Raman spectroscopic measurements of the arsenolite–hydrogen inclusion compound As 4 O 6 ·2H 2 were performed in diamond anvil cells at high pressure and variable temperature down to 80 K. The experimental results were complemented by ab initio molecular dynamics simulations and phonon calculations. Observation of three hydrogen vibrons in As 4 O 6 ·2H 2 is reported in the entire temperature and pressure range studied (up to 24 GPa). While the experiments performed with protium and deuterium at variable temperatures allowed for the assignment of two vibrons as Q 1 (1) and Q 1 (0) transitions of ortho and para spin isomers of hydrogen trapped in the inclusion compound, the origin of the third vibron could not be unequivocally established. Low-temperature spectra revealed that the lowest-frequency vibron is actually composed of two overlapping bands of A g and T 2g symmetries dominated by H 2 stretching modes as predicted by our previous density functional theory calculations. We observed low-frequency modes of As 4 O 6 ·2H 2 vibrations dominated by H 2 “librations,” which were missed in a previous study. A low-temperature fine structure was observed for the J = 0 → 2 and J = 1 → 3 manifolds of hydrogen trapped in As 4 O 6 ·2H 2 , indicating the lifting of degeneracy due to an anisotropic environment. A non-spherical distribution was captured by molecular dynamics simulations, which revealed that the trajectory of H 2 molecules is skewed along the crystallographic $\langle$111$\rangle$ direction. Last but not least, low-temperature synchrotron powder x-ray diffraction measurements on As 4 O 6 ·2H 2 revealed that the bulk structure of the compound is preserved down to 5 K at 1.6 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dual Orbital Degeneracy Lifting in a Strongly Correlated Electron System

The local structure of NaTiSi 2 O 6 is examined across its Ti-dimerization orbital-assisted Peierls transition at 210 K. An atomic pair distribution function approach evidences local symmetry breaking preexisting far above the transition. The analysis unravels that, on warming, the dimers evolve into a short range orbital degeneracy lifted (ODL) state of dual orbital character, persisting up to at least 490 K. The ODL state is correlated over the length scale spanning ~ 6 sites of the Ti zigzag chains. Results imply that the ODL phenomenology extends to strongly correlated electron systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Deep learning interfacial momentum closures in coarse-mesh CFD two-phase flow simulation using validation data

Multiphase flow phenomena have been widely observed in the industrial applications while it remains a challenging yet unsolved problems. Three-dimensional computational fluid dynamics (CFD) approaches resolve the flow fields on a finer special and temporal scales which can complement the dedicated experimental study. However, closures have to be introduced to reflect the underlying physics in multiphase flow. Among them, the interfacial forces, including drag, lift, turbulent dispersion and wall lubrication forces, play in important role on the bubble’s distribution and migration in liquid-vapor two-phase flow. Development of those closures traditionally rely on the experimental data and analytical derivation with simplified assumptions which usually cannot deliver a universal solution across wide range of flow conditions. In this paper, a data-driven approach, named as Feature Similarity Measurement (FSM), is developed and applied to improve the simulation capability of two-phase flow with coarse-mesh CFD approach. Interfacial momentum transfer in adiabatic bubbly flow serves as the focus of the present study. Both a mature and a simplified set of interfacial closures are taken as the low fidelity data. Experimental data and fine mesh CFD simulations results are adopted as high-fidelity data. Qualitative and quantitative analysis are performed in this paper which reveals that FSM can substantially improve the prediction of coarse mesh CFD model regardless of the choice of interfacial closures and it provides scalability and consistency across discontinuous flow regimes. Furthermore, it demonstrates that data-driven method can aid the multiphase flow modeling by exploring the connections between local physical features and simulation errors.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Film Cooling Performance Prediction for Air and Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing supercritical CO 2 . The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. Herein, a computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state Reynolds-averaged Navier–Stokes equations were solved along with the (shear-stress transport) SST k–ω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness are presented at different operating conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Film Cooling Performance Predictions For Air And Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling geometries. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing a supercritical fluid. The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. A computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state RANS equations were solved along with the SST kω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness will be presented at different operating conditions. Recommendations for future studies will be given wherever applicable.

42 ENGINEERING↗
DOE OSTI2020

Nanoscale degeneracy lifting in a geometrically frustrated antiferromagnet

The local atomic and magnetic structures of the compounds A MnO 2 (A = Na, Cu), which realize a geometrically frustrated, spatially anisotropic triangular lattice of Mn spins, have been investigated by atomic and magnetic pair distribution function analysis of neutron total scattering data. Relief of frustration in CuMnO 2 is accompanied by a conventional cooperative symmetry-lowering lattice distortion driven by Néel order. In NaMnO 2 , however, the distortion has a short-range nature. A cooperative interaction between the locally broken symmetry and short-range magnetic correlations lifts the magnetic degeneracy on a nanometer length scale, enabling long-range magnetic order in the Na derivative. The degree of frustration, mediated by residual disorder, contributes to the rather differing pathways to a single, stable magnetic ground state in these two related compounds. This study demonstrates how nanoscale structural distortions that cause local-scale perturbations can lift the ground-state degeneracy and trigger macroscopic magnetic order.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Incorporating an Interactive Fire Plume-Rise Model in the DOE's Energy Exascale Earth System Model Version 1 (E3SMv1) and Examining Aerosol Radiative Effect

The vertical distribution of biomass burning aerosol (BBA) is important in regulating their impacts on weather and climate. The plume-rise process affects the injection height of BBA and interacts with the air parcel lifting and cloud processes. However, these processes are not represented in most global climate models. In this study, we replaced the fixed vertical profiles of monthly BBA emissions in the Department of Energy's Energy Exascale Earth System Model version 1 (E3SMv1) with an interactive fire plume-rise model. The vertical distribution of BBA emissions was calculated as a function of ambient thermodynamic conditions from the host E3SMv1, with distributions of fire sizes and sensible heat fluxes derived from the observations. The maximum fire radiative power (FRP) technique was used to determine the fire size. Scaling-FRP technique is used to calculate the wildfire heat release. Daily BBA emission, superimposed with a fire diurnal cycle retrieved from the satellite observation, was included in model simulations. The model shows improved agreement with satellite retrievals and in situ measurement during the National Oceanic and Atmospheric Administration Wildfire Experiment for Cloud chemistry, Aerosol absorption, and Nitrogen campaign. The model-observation comparison demonstrates the importance of the plume-rise model and fire diurnal cycle assumption in determining the BBA fields. We also find that E3SMv1 with new features produces a larger carbonaceous aerosol burden, leading to 0.13 W m –2 warming at the top of atmosphere compared to the default E3SMv1. This highlights the importance of accurately representing the BBA injection height and indicates a no-linear nature in the BBA-induced radiative effect.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗