Search NASA⌕ Search

SEARCH · Search NASA

Results for “MASS SPECTROSCOPY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The sweeper spectrometer for neutron invariant-mass spectroscopy at FRIB

Neutron invariant-mass spectroscopy (NIMS) is a key technique for studying unbound and weakly bound nuclei at the limits of stability. At the Facility for Rare Isotope Beams (FRIB), such measurements are performed using the Sweeper spectrometer, a large-gap, high-rigidity dipole system coupled to the MoNA-LISA neutron detector arrays. To meet the demands imposed by higher beam energies (>130 MeV/u) and the broad cocktail-beam selection available at FRIB, the spectrometer has recently been upgraded to improve particle-identification and detection performance. Upstream of the reaction target, a plastic scintillator with Silicon photomultiplier (SiPM) readout provides the global trigger and time reference, two parallel plate avalanche counters (PPACs) track the trajectories of incoming beam particles, and a silicon PIN detector measures the energy loss, ΔE, for charge (Z) identification. After the Sweeper magnet, the trajectories of the reaction products are tracked by two micro-pattern drift chambers (MPDCs), their charge (Z) is identified by a Frisch-grid ionization chamber (FG-IC), and their mass-to-charge ratio (A/Q) is deduced by time-of-flight measurement using a fast plastic scintillator read out by an array of photomultiplier tubes (PMTs). The detection system also incorporates the Modular Neutron Array (MoNA) for neutron detection and the CAESium-iodide scintillator ARray (CAESAR) for high-efficiency γ-ray measurements to enable full kinematic reconstruction. Performance was evaluated using a cocktail beam around 37 Al accelerated at E ≈ 130 MeV/u during the first FRIB campaign, demonstrating the readiness of the upgraded system for future studies of nuclei at and beyond the neutron drip line.

Particle identification methods↗
DOE OSTI2024

Evolution of shell gaps in the neutron-poor calcium region from invariant-mass spectroscopy of 37,38 Sc, 35 Ca, 34 K

A fast secondary beam of 37 Ca impinged on a 9 Be target resulting in a set of reactions populating proton-rich nuclei including 35 Ca and the first observations of 37,38 Sc and 34 K. Invariant-mass spectroscopy, used to reconstruct proton decays for these nuclei, yielded three new ground-state masses and information on their low-lying structures. The newly measured mass excesses are: ΔM( 37 Sc) = 3500(410) keV, ΔM( 38 Sc) = –4656(14) keV, and ΔM( 34 K) = –1487(17) keV. These nuclei straddle the well-known Z = 20 shell closure as well as the N = 16 subshell closure. Furthermore, trends in separation energies help elucidate how nuclear structure evolves showing a fading of the Z = 20 shell gap for N ≥ 18 and indications of a N = 16 subshell gap.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Self-Inhibition Phenomena in Cu 3 Pt Oxidation by CO 2

Here, this study investigates the oxidation behavior of Cu 3 Pt(100) in CO 2 using a combination of ambient-pressure X-ray photoelectron spectroscopy, mass spectroscopy, and density functional theory modeling. Our in situ measurements reveal the simultaneous oxidation and reduction of Cu 2 O due to the opposing effects of atomic oxygen and CO generated from dissociative CO 2 adsorption, leading to a dynamic equilibrium state of simultaneously occurring redox reactions. Complementary atomistic calculations elucidate the inhibitory effects of subsurface Pt enrichment and the counteracting roles of CO 2 and CO in surface oxidation and reduction. These results provide mechanistic insights into the dissociative pathway of CO 2 molecules and dynamic evolution of surface composition and reactivity of Cu-based alloy catalysts in CO 2 -rich environments, with broader implications for tuning gas–surface reactions by manipulating gas reactants or solid surface composition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Cascade CO 2 Insertion in Carbanion Ionic Liquids Driven by Structure Rearrangement

The CO 2 chemisorption in state-of-the-art sorbents based on oxide/hydroxide/amine moieties is driven by strong chemical bonding formation in the carbonate/bicarbonate/carbamate products, which in turn leads to high energy input in sorbent regeneration. In addition, the CO 2 uptake capacity was limited by the active sites’ utilization efficiency, with each active site incorporating one CO 2 molecule or less. In this work, a new concept and generation of sorbent was developed to achieve cascade insertion of multiple CO 2 molecules by leveraging structure rearrangement as the driving force, leading to in situ generation of extra CO 2 -binding sites and significantly reduced energy input for CO 2 release. The designed ionic liquids (ILs) containing carbanions with conjugated and asymmetric structure, deprotonated (methylsulfonyl)acetonitrile ([MSA]) anion, allowed the cascade insertion of two CO 2 molecules via consecutive C–C and O–C bond formations. The proton transfer and structure rearrangement of the carboxylic acid intermediates played critical roles in stabilizing the first integrated CO 2 and generating extra electron-rich oxygen sites for the insertion of the second CO 2 . The structure variation and reaction pathway were confirmed by operando spectroscopy, magnetic resonance spectroscopy (NMR), mass spectroscopy, and computational chemistry. The energy input in sorbent regeneration could be further reduced by harnessing the phase-changing behavior of the carbanion salts in ether solutions upon reacting with CO 2 , avoiding the energy consumption in heating the solvent. In conclusion, the fundamental insights obtained herein provide a promising approach to greatly improve the CO 2 sorption performance via sophisticated molecular-scale structural engineering of the sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fission gas trapped in Chornobyl fuel microparticles reveals details of reactor operations

The isotopic ratios of fission gas would provide important source information of a nuclear fuel sample found in the environment. However, it is believed that during a reactor accident like Chornobyl all fission gas is lost and that the radioactive particles found in the Chornobyl Exclusion Zone today are depleted in gases by the initial explosion and subsequent fire. We disprove this hypothesis by detection and analysis of trapped krypton and xenon in these particles. Our analysis of krypton and xenon isotopes by noble gas mass spectroscopy in combination with resonance ionization mass spectrometry establishes that important information about reactor operations like age, neutron flux and plutonium fission fraction can still be reconstructed from individual micrometer-sized particles even after decades of weathering in the environment.

Chornobyl↗
DOE OSTI2025

Characterization of Tank 9H Annulus Sample in Support of Residual Material Inventory Determinations

The Savannah River National Laboratory (SRNL) was requested by Savannah River Mission Completion (SRMC) to provide sample preparation and characterization of the Tank 9H annulus sample in support of Residual Material Inventory Determinations. One Tank 9H sample in three vials [HTF-9-25-13, HTF-9-25-14 and HTF-9-25-15], with each vial containing approximately 200 mL of the Tank 9H annulus salt solution, were delivered to the SRNL Shielded Cells for sample preparation and characterizations in February 2025. The density of the “as-received” solution contained in each of the three Tank 9H annulus sample vials were determined followed by a solid-liquid separation on each one using 0.45-micron Nalgene® nylon filter membranes. The resulting filtrates were combined to form the Tank 9H annulus sample with a total volume of about 600 mL. The combined wet solid fractions, about a total of 4.8 grams of salt material, remaining on the filter membranes were air-dried in the Shielded Cells for 72 hours. The total weight of the air-dried solids was 2.1 grams. These air-dried solids were washed with deionized water (DI water) at a phase ratio of 60 mL DI water/gram of solids to recover insoluble solids, if any. No visible or measurable quantity of insoluble solids were recovered after DI water washing of the air-dried solids because the air-dried solids completely dissolved in the DI water. The solid fraction-wash water was not combined with the 600 mL of the filtrate solution, and the resulting solution was not screened or analyzed for radionuclides. Aliquot sample volumes of the undiluted Tank 9H annulus sample were sent to the SRNL analytical services groups for radionuclides, elementals, anions and total mercury analysis by various methods including radiochemical separations/counting methods, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and special preparations. All sample analyses were performed in triplicate. This report presents the analytical characterization results for the Tank 9H annulus sample. The results are also reported where analytical methods yielded additional analytes, other than those requested by SRMC. In the characterization of the Tank 9H annulus sample, the detection limits for all the analytes, as specified in the Technical Task Request (TTR) and Task Technical and Quality Assurance Plan (TTQAP), were met.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Contrasting Effects of Catecholate and Hydroxamate Siderophores on Molybdenite Dissolution

Molybdenum (Mo) is essential for many enzymes but is often sequestered within minerals, rendering it not readily bioavailable. Metallophores, metabolites secreted by microorganisms and plants, promote mineral dissolution to increase metal bioavailability. However, interactions between metallophores and Mo-bearing minerals remain unclear. Here, in this study, catecholate protochelin and hydroxamate desferrioxamine B (DFOB) were utilized to examine their effects on dissolution of the common Mo-bearing mineral, molybdenite (MoS 2 ), under both oxic and anoxic conditions. Protochelin promoted molybdenite dissolution under oxic conditions with the formation of MoO 3 on the surface and Mo-siderophore complexes in solution. This was attributed to air-oxidation of both molybdenite and protochelin, as evidenced by lack of dissolution under anoxic conditions but enhanced dissolution by either pre-oxidized protochelin or pre-oxidized molybdenite. Liquid chromatography-mass spectroscopy (LC-MS), X-ray photoelectron spectroscopy (XPS), and Time-of-flight secondary ion mass spectrometry (ToF-SIMS) analyses revealed degradation of protochelin and adsorptions of its byproducts on molybdenite surface to promote dissolution. Conversely, DFOB inhibited molybdenite dissolution under both oxic and anoxic conditions, likely attributed to surface adsorption of DFOB and its weak complexation with Mo(VI) at the circumneutral pH. This work highlights the need to consider the balance between promoting and inhibitory effects of different metallophores on Mo-mineral dissolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Interaction of Molecular Hydrogen on α-Pu at 300 K: Nucleation of Hydrides and Pu-Catalyzed Carbides

An α-Pu sample was studied in its “as-received” and “sputtered” state by both X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectroscopy (ToF-SIMS). Analysis of the “as-received” surface indicated significant carbon and oxygen, with oxygen signal pertaining to plutonium dioxide (PuO 2 ) and sesquioxide (Pu 2 O 3 ). The “sputtered” clean metal surface was then dosed with hydrogen (H 2 ) gas at 300 K and found to nucleate hydride species (PuH x ). Interestingly, H 2 was observed to be critical for nucleation of carbides (Pu x C y ) by acting as a catalyst for Pu’s reaction with background gases. Because Pu metal has a high affinity for oxygen, reoxidation occurred under UHV, forming Pu x O y and disrupting both PuH x and Pu x C y growth. Observations from the experiments were modeled for the α-Pu(020) surface, illustrating the ability of H 2 to readily dissociate onto sputtered and speciated surfaces at 300 K. The projected density of states from these calculations were compared to experiments, showing good agreement between the Pu 5f, 6d, and 7s states and the H 1s, O 2p, and C 2p valence states. Overall, the above results indicated that the formed hydride layer is unstable at 300 K in UHV conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elucidating the corrosion mechanism of Ni-based superalloys in the presence of uranium-containing chloride molten salt

The United States Department of Energy (DOE) is committed to the advancement of nuclear reactor technology through initiatives such as the Advanced Reactor Development Program (ARDP), in an effort to diversify the United States energy portfolio towards more sustainable energy options. The ARDP includes demonstration by industry partners of molten chloride fast reactors (MCFRs). Construction of MCFRs requires qualified nuclear structural materials. Unfortunately, there are no current materials that are fully qualified by the Nuclear Regulatory Commission for the construction of molten salt reactors, including MCFRs. Adapting current structural material qualifications requires expansion of our current knowledgebase on the property-performance relationships regarding corrosion performance. In this investigation, we assess microstructural changes in a Ni-based superalloy after exposure to a UCl3¬-containing chloride salt eutectic mixture through a correlated multi-modal approach combining several advanced characterization techniques, including scanning electron microscopy/focused ion beam (SEM/FIB) and transmission electron microscopy (TEM). SEM/FIB analysis will illustrate changes in elemental composition, microstructure, and isotopic information acquired from energy x-ray dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), and secondary ion mass spectroscopy (SIMS), respectively. This information will then aid in identifying localized regions to elucidate the corrosion mechanism with TEM through a combination of electron diffraction, electron energy loss spectroscopy (EELS), and additional EDS. The findings from this investigation will further expand our assessment of the corrosion performance of structural materials in molten salt chloride systems, aiding to developing fully qualified materials for construction of MCFRs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Focused ion beam (FIB) milling is a commonly used tool for nanoscale material processing, such as for transmission electron microscopy (TEM) sample preparation, or the creation of fiducial markers prior to other processes and measurements. During milling, a high energy ion beam is used to remove material via sputtering. The expelled target material may return to the sample surface however, affecting subsequent measurements. Beam spreading or irradiation due to neutral gallium may also irradiate a larger area than intended. Extensive research has explored the effects of FIB milling on the prepared TEM sample, but few have looked at the effects of milling on the properties of the sample surrounding the milled region. We use multiple pump-probe laser-based techniques (time domain thermoreflectance and steady-state thermoreflectance) to measure the spatial extent of FIB-induced surface/subsurface changes on a series of silicon wafers milled at multiple currents and doses. We supplement these measurements with high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy, stylus profilometry, and time-of-flight secondary ion mass spectroscopy. We find a sample surface affected by the FIB up to 1 mm from where milling occurred, with a notable dependence on the ion beam current. We also note remarkably high sensitivity to surface defects using the thermoreflectance metrologies, including detection where other measurements failed.

defects↗
DOE OSTI2026

Co-templating of polyoxoniobates and silicate/germanate trimer-rings in crystals and inorganic gels

Polyoxometalate (POM) supramolecular gels are a growing family of materials, both for understanding fundamental self-assembly and fabricating flexible monolithic materials that retain the function of metal oxides. Here, we exploited the pH-dependent speciation of polyoxoniobates (PONbs), targeting the formation of PONb-containing supramolecular gels that contain other low molecular weight components (silicate, germanate, phosphate, and carbonate). The introduction of gaseous CO 2 into aqueous hexaniobate solutions resulted in the formation of both new crystalline phases and highly transparent gels. The crystalline phases, formulated Cs 24 [Nb 7 O 22 (NbO(CO 3 ) 2 ) 9 (Si 3 O 9 )]·19.6H 2 O and Cs 21 Na 3 [Nb 7 O 22 (NbO(CO 3 ) 2 ) 9 (Ge 3 O 9 )]·33.6H 2 O are templated by a rare planar [X 3 O 9 ] 6− (X = Si, Ge) ring. Crystalline phases were not obtained with phosphate; instead, the gels contain a mixture of phosphate-centred PONbs and network-forming phosphate. POM speciation within the gels, physical properties, and assembly mechanisms were benchmarked by solution and solid-state nuclear magnetic resonance (NMR) spectroscopy, vibrational spectroscopies, small-angle X-ray scattering (SAXS), and thermogravimetry-mass spectroscopy. Optical analysis and dielectric behavior of the gels confirmed that they are highly transparent ionic and electronic conductors. The alkali and hydroxide concentration controls the formation of crystalline materials or supramolecular gels while maintaining the same network building blocks, providing a rare opportunity to describe the molecular-level structure of inorganic amorphous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Rigor and Reproducibility in Electrocatalysis: Best Practices for Operando Studies

Operando measurements have rapidly expanded the scope of electrocatalysis by enabling direct observation of catalytic interfaces under working conditions and by linking structural, compositional, and spectroscopic observables to activity and selectivity. However, the growth of operando methods has outpaced the adoption of broadly shared experimental standards, creating persistent challenges in reproducibility, interpretation, and comparison across laboratories and platforms. This perspective synthesizes discussions from the 2025 National Science Foundation Workshop on Rigor and Reproducibility in Electrocatalysis and outlines a practical framework for the rigorous use of operando measurements in electrocatalysis. We highlight three recurring needs: careful implementation of complex methods to avoid overinterpretation; recognition that (subtle) differences in reactor architecture, hydrodynamics, and electrical boundary conditions can alter apparent kinetics and selectivity; and transparent reporting standards that enable meaningful cross-comparison without constraining measurement-specific cell innovation. Focusing on widely used techniques (including X-ray and vibrational spectroscopies, mass spectrometry, and electron microscopy), we discuss technique-specific pitfalls, cross-validation strategies, and recurring platform-agnostic considerations such as mass transport, current distribution, temporal-resolution mismatches, and catalyst evolution. This Perspective aims to strengthen the mechanistic inference and improve the reproducibility, comparability, and predictive value of operando electrocatalysis research.

X-ray absorption spectroscopy↗
DOE OSTI2024

Exploring constituent redistribution in irradiated U-19Pu-14Zr fuel via electron probe microanalysis

Here, the phenomena of constituent redistribution, wherein a previously homogeneous metallic fuel forms discrete, radially concentric compositional zones upon irradiation was investigated by examining an irradiated U-19Pu-14Zr fuel (where numbers represent wt. %) with a burnup of 11.5 at.% with electron probe microanalysis (EPMA) and quadruple inductively coupled plasma mass spectroscopy (Q-ICP-MS). EPMA-generated U, Pu, and Zr compositional data obtained from a diameter traverse of the sample was converted to mass and was used to: 1) compare the overall fuel element analysis results between the two methods, 2) determine the number of compositionally distinct zones forming as a result of constituent redistribution; and 3) quantify the post-irradiation loss or gain of U, Pu, and Zr atoms in each distinct compositional zone. Weight percent concentrations of U, Pu, and Zr for the overall cross section compare favorably between the two analytical methods, suggesting that the spatially resolved EPMA analysis complements bulk chemical analysis. Among the four identified compositional zones, post-irradiation quantification of U, Pu, and Zr elemental atom content changes shows that the quantity of U atoms lost from the innermost zone is slightly less than the quantity of U atoms gained by the middle two zones, and the quantity of Zr atoms lost from the high-U third zone is slightly less than is gained by the two innermost zones. Pu is lost from all four zones, although the innermost zone and the high-U third zone lose a significantly higher percentage (> 22 %) of their initial Pu atoms than the other two zones. For all three elements, EPMA cannot distinguish between atoms lost due to transport to a different zone from atoms lost due to nuclear processes; however, the insight gained from using this process can be used to experiment with new modeling techniques to predict constituent redistribution in U-Pu-Zr fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

New Insights into Nonthermal Plasma-Assisted Poly(vinyl alcohol) Depolymerization Catalyzed by TiO 2

Here, in this study, we investigated the solid residual poly(vinyl alcohol) (PVA) and TiO 2 after nonthermal air, CO 2 , and N 2 plasma depolymerization in the absence and presence of TiO 2 . Scanning electron microscopy studies showed the absence of highly viscous tar and carbonaceous residues on the surfaces of PVA and TiO 2 . In the absence of TiO 2 , PVA particles exhibited micron-sized holes on their surfaces, whereas in the presence of TiO 2 , the surface roughness of PVA particles was observed at the submicron scale. These observations suggest that TiO 2 facilitates the even distribution of nonthermal plasma at a submicron scale, leading to a more uniform depolymerization of PVA surfaces. Raman, Fourier transform infrared spectroscopy, and X-ray absorption spectroscopy showed that (i) the surface of residual PVA contains mainly ketone functional groups and less C-H bonds than the pristine PVA and (ii) further confirmed the absence of highly viscous tar and carbonaceous residues on both used TiO 2 and residual PVA. The nuclear magnetic resonance and mass spectroscopy suggested that the PVA is growing back to poly polyvinyl acetate by the esterification reaction, and the ethers are produced by the acetal reaction between PVA and aldehyde. The transmission electron microscopy and X-ray diffraction analysis indicated no major crystal structural change of the TiO 2 catalyst after the plasma reactions. This study demonstrates that nonthermal plasma-assisted depolymerization is a viable alternative to thermal depolymerization, offering the unique advantage of converting polymer wastes into gaseous small organic molecules without generating recalcitrant viscous tar and carbonaceous residues on the surfaces of the polymer and TiO 2 catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

In situ molecular imaging of ion clusters reveals the acid gas capture capacity and mechanism of water-lean ionic liquids

Water-lean solvents are a promising technology for capturing acid gases like carbon dioxide (CO 2 ). In situ liquid time-of-flight secondary ionization mass spectroscopy (ToF-SIMS) is used to study a representative solvent N-(2-ethoxyethyl)-3-morpholinopropan-1-amine (2-EEMPA) with different CO 2 loadings to reveal the complex solvent structure upon CO 2 capture. Characteristic peaks of 2-EEMPA, such as m/z – 215 C 11 H 23 N 2 O 2 – (deprotonated 2-EEMPA) and m/z + 217 C 11 H 25 N 2 O 2 + (protonated 2-EEMPA), are detected due to acid gas uptake. Also, solvent molecules and carboxylate ion pairs, such as m/z – 259 C 12 H 23 N 2 O 4 – [(deprotonated 2-EEMPA∙∙∙CO 2 )] and m/z + 261 C 12 H 25 N 2 O 4 + (protonated 2-EEMPA∙∙∙CO 2 ), are observed. Interestingly, more than one CO 2 molecule can be captured per each solvent molecule as evidenced in SIMS mass spectra, for example, m/z – 321 C 13 H 25 N 2 O 7 – [(deprotonated 2-EEMPA)∙∙∙2CO 2 ∙∙∙H 2 O], m/z + 305 C 13 H 25 N 2 O 4 + [(protonated 2-EEMPA)∙∙∙2CO 2 ], m/z – 389 C 17 H 29 N 2 O 8 – [(deprotonated 2-EEMPA)∙∙∙3CO 2 ∙∙∙3CH 2 ], and m/z + 373 C 16 H 25 N 2 O 8 + [(protonated 2-EEMPA)∙∙∙3CO 2 ∙∙∙2C]. However, the monomer of 2-EEMPA and CO 2 seems to be most prevalent. Furthermore, solvent clusters are detected in loaded solvents, for instance m/z + 433 C 22 H 49 N 4 O 4 + [(2-EEMPA)2∙∙∙H] and m/z + 646 [(2-EEMPA) 3 -2H], while capturing CO 2 at different amounts. Relative abundance of cluster ions provides a semi-qualitative venue to assess the free energies of gas capture energetics, indicating the relative stability trend within the same solvent system, previously impossible. These observed ion clusters are verified with molecular modeling, where dimer, trimer, and cluster ions are validated for their presence either due to weak molecular interactions or hydrogen bonds. In situ molecular imaging of ionic liquids and molecular modeling reveals that the acid gas capture mechanism by ionic liquids includes both physical adsorption and chemical bonding with multiple reaction pathways, engaging cluster formation and alteration of solvent structures.

Acid gas capture↗
DOE OSTI2024

A Scalable & Non-Destructive Characterization Strategy to Study Semiconductor/Dielectric Interfaces and Predict Wafer-Level Device Performance

The defect density present at the dielectric-semiconductor interface in an MOS structure directly influences the channel carrier characteristics in semiconductor devices, especially in wide bandgap material systems used in power devices. While these trap defects are typically quantified through electrical characterization of MOS-capacitor test structures, this treatment offers very little insight into the physical nature of interface defects. Such shortcomings demand a physical characterization strategy to guide fabrication optimization. X-ray photoelectron spectroscopy (XPS) is suggested as a viable technique to determine chemical data for dielectric interfaces formed using atomic layer deposition (ALD) on GaN substrates. Previously, 1-D XPS characterization has confirmed the presence of a Ga x O y interlayer between ALD dielectrics and the GaN substrate. In this work, XPS data is serially collected to form 2-D images of an ALD-Al 2 O 3 /GaN interface as a proof-of-concept experiment for in-situ XPS quality monitoring during ALD processing. The information provided by this work reveals some of the challenges for incorporating XPS characterization as an in-situ strategy during fabrication of GaN-based devices. Separately, electrical mapping of a 2-D array of ALD-Al 2 O 3 /GaN MOS-capacitor devices provide a means to quantify the spatial variations in interface quality across a single wafer. Physical characterization techniques, such as time-of-flight secondary ion mass spectroscopy, provide additional chemical information about the Al 2 O 3 /Ga x O y /GaN structure that complement the electrical mapping results. This analysis shows that a higher Ga x O y content correlates with higher interface state defects for trap energies deep in the band gap.

42 ENGINEERING↗
DOE OSTI2026

Comparative Dissolution of Iron-Bearing Minerals by Catecholate and Hydroxamate Siderophores under Oxic and Anoxic Conditions

Siderophores play a crucial role in biological iron (Fe) acquisition and mobilization by promoting Fe mineral and rock weathering. While the effects of the hydroxamate siderophore desferrioxamine B (DFOB) have been extensively studied, the role of catecholates in the dissolution of Fe mineral and rock under varying redox conditions remain limited. Moreover, despite Fe being one of the most redox-active metals, the siderophore-mediated redox transformations of solid-phase Fe and their impact on mineral dissolution are not well understood. Herein, this study systematically investigated dissolution behavior of both Fe(II) and Fe(III)-bearing minerals and rocks (Fe(II)- bearing basalt and olivine, and Fe(III)- bearing nontronite and goethite), by two structurally distinct biological siderophores, catecholate protochelin and hydroxamate DFOB, under both oxic and anoxic conditions. Batch experiments quantified Fe and transition metals (Mn, Ni, Zn, Mo) released from the tested minerals in the presence of siderophores. Throughout the dissolution experiments, siderophore concentrations and Fe-siderophore complexation in solutions were measured using UV-vis spectrometry. Fe redox changes under oxic and anoxic conditions by siderophores were determined, and mineral surface alterations following siderophore treatments were characterized through scanning electron microscopy (SEM) and time-of-flight secondary ion mass spectroscopy (ToF-SIMS). Results revealed distinct interplays of dissolution mechanisms, including ligand-exchange promoted dissolution and reductive dissolution, along with Fe(III) reduction and Fe(II) oxidation, contributing to the Fe(II)- and Fe(III)-rich mineral weathering under varying redox conditions. Under oxic conditions, both protochelin and DFOB enhanced Fe release from Fe(II)-rich basalt and olivine more effectively than from Fe(III)-rich minerals. DFOB induced greater Fe(II)-mineral dissolution than protochelin. This difference was attributed to a higher level of Fe(II) oxidation by DFOB in contrast to protochelin, as well as the protochelin oxidation with the loss of Fe binding groups (catechols). Under anoxic conditions, both siderophores significantly reduced Fe(III) in nontronite and goethite, with protochelin demonstrating substantially stronger Fe(III) reduction capacity than DFOB. However, Fe(III) reduction negatively impacted Fe release from Fe(III)-rich minerals. Instead, Fe release from Fe(II)-rich minerals was enhanced under anoxic conditions due to the absence of Fe(II) oxidation and labile Fe(II). Variations in siderophore adsorption also contributed to dissolution differences. Beyond iron, the release of transition metals from tested minerals was influenced by elemental contents, mineral compositions, and siderophore types, revealing distinct metal- and siderophore-dependent patterns. This systematic investigation highlights the roles of siderophores in Fe redox cycling and metal mobilization, enhancing our understanding of different siderophore behaviors in siderophore-mediated microbial metal acquisition within redox-dynamic environments, with implications for bioleaching industries and applications in agriculture and climate change mitigation.

Guo, Dongyi↗
DOE OSTI2025

Development and characterization of an aerosol-generated multi-method analytical particle test material

Ceria (CeO 2 ) particles with low to ultra-low loading of nickel dopant were produced using an aerosol-based, droplet-to-particle synthesis via an in-line calcination technique. This aerosol-based synthesis method enables the production of particles with a monodisperse size distribution. These produced and well-characterized, multi-element, ceria-based particles demonstrate a material exemplar for multi-method analytical testing. They were prepared from a cerium nitrate feedstock where low loading nickel dopant was added at target Ni/(Ni + Ce) atomic percents of 1 %, 0.1 %, and 0.01 %, using a nickel nitrate spike. This methodology proved to produce ceria particles doped with a dynamic range of low to ultra-low loadings of nickel over a 24-h period, with consistent size distribution, morphology, and composition. The successful incorporation of nickel was demonstrated with bulk and single particle inductively coupled plasma mass spectroscopy and revealed notable particle-to-particle elemental homogeneity. X-ray photoelectron spectroscopy demonstrated the presence of a high concentration of nickel dopant incorporated preferentially toward the surface of the particles, and that this dopant aided oxidation of surface Ce(III) atoms to Ce(IV). These particle test materials were then validated through X-ray absorption near edge spectroscopy, comparing the ultra-low 0.01 % Ni and low 1 % Ni-doped ceria samples. This revealed a more-reduced oxidation state of the nickel with an increase in dopant concentration. Finally, this work demonstrates a synthesis and systematic characterization scheme to produce multi-method analytical test particulates.

36 MATERIALS SCIENCE↗