Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxidation resistant coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Environmental barrier coatings on SiC without a silicon bond coating: oxidation resistance, failure modes, and future improvements

Environmental barrier coatings (EBCs) are used to mitigate chemical reactions between SiC ceramic matrix composite (CMC) components and the H 2 O in combustion gas in turbine hot sections. CMCs are currently temperature-limited by the Si-bond coating, which melts at ~ 1414 °C. This work explores EBCs where the bond coating was removed to achieve higher operating temperatures. Various versions of enhanced roughness SiC were utilized to improve EBC adhesion to the substrates prior to 1 h furnace cycle testing in steam at 1250–1425 °C. The enhanced SiC roughness resulted in short coating lifetimes as the roughness was oxidized away with SiO 2 formation. Further, isothermal furnace exposures at 1400–1600 °C showed Yb 2 Si 2 O 7 /Yb 2 SiO 5 EBC microstructural changes, resulting in premature debonding from the substrates. Finally, this work provides baseline requirements for the development of both next-generation EBCs and bond coating strategies to overcome the current limitation of the Si-bond coating melting temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Uncertainty-Based Design: Finite Element and Explainable Machine Learning Modeling of Carbon–Carbon Composites for Ultra-High Temperature Solar Receivers

Design under uncertainty has significantly grown in research developments during the past decade. Additionally, machine learning (ML) and explainable ML (XML) have offered various opportunities to provide reliable predictable models. The current article investigates the use of finite element modeling (FEM), ML and XML predictions, and uncertain-based design of carbon-carbon (C-C) composites for use in ultra-high temperatures. A C-C composite concentrating solar power (CSP) as a microvascular receiver is considered as a case study. These C-C composites are fiber composites with directly integrated carbonized microchannels to form a lightweight, high-absorptivity material that includes an embedded microvascular network of channels. The topology of these microchannels is engineered to optimize heat transfer to a supercritical carbon dioxide (sCO2) heat transfer fluid. The mechanical characterization of C-C composites is highly challenging. Thus, designing every component made of C-C composites for ultra-high temperature applications needs an uncertainty-based analysis. As a part of a comprehensive project on the development of a novel carbonized microvascular C-C composite, this paper explores C-C composite sensitivity analysis, FEM, ML prediction, and XML analysis. The resulting composite can then be carbonized and coated with an oxidation-resistant coating to form a thermally efficient and mechanically robust C-C composite. An ANSYS 3-D-FE model was used to analyze the CSP’s stress/strain. To consider the variability in the mechanical and thermal properties of C-C composites, various mechanical properties are considered as the ANSYS FEM’s input. A synthetic dataset from 730 ANSYS runs was produced to feed into the ML and XML algorithms for uncertainty analysis and prediction. The ML and XML algorithms could accurately predict the CSP stresses/strains.

Daghigh, Vahid (ORCID:0000000298941620)↗
DOE OSTI2023

Computational fluid dynamics investigations of flow, heat transfer, and oxidation in heat recovery steam generator

Modern heat recovery steam generators (HRSGs) operate at elevated temperatures, leading to the formation of oxides inside the tubes of heat exchangers (HXs). This oxide growth reduces the heat recovery efficiency. Moreover, after reaching a certain critical thickness, some oxide scales detach from the tube surface (exfoliation), causing erosion damage to the components downstream. Predicting the metal temperature distribution and associated oxide thickness in the HXs of an HRSG can aid in mitigating these problems. Here, a computational fluid dynamics (CFD) model was developed within the commercial code STAR-CCM+ for the prediction of fluid flow, conjugate heat transfer, and associated oxidation in HRSGs. Moreover, a new Porous Media Model (PMM) method was developed to model the fin effect on the heat transfer in HX, which can substantially reduce the prohibitive computational costs of fin meshes. The developed CFD model was used to conduct a high-fidelity simulation of a real-scale HRSG to investigate flow, heat transfer, and oxide growth. The calculated oxide thickness on different tubes can be used to identify HX regions that require oxide-resistant coatings to prevent exfoliation and ensuing damages. Furthermore, this CFD framework can serve as a reference for future studies that intend to model and investigate high-temperature oxidation in HXs used for any applications.

42 ENGINEERING↗
DOE OSTI2023

High-Sensitivity Low-Energy Ion Spectroscopy with Sub-Nanometer Depth Resolution Reveals Oxidation Resistance of MoS 2 Increases with Film Density and Shear-Induced Nanostructural Modifications of the Surface

For decades, density has been attributed as a critical aspect of the structure of sputter-deposited nanocrystalline molybdenum disulfide (MoS 2 ) coatings impacting oxidation resistance and wear resistance. Despite its importance, there are few examples in the literature that explicitly investigate the relationship between the density and oxidation behaviors of MoS 2 coatings. Aging and oxidation are primary considerations for the use of MoS 2 coatings in aerospace applications as they inevitably experience prolonged storage in water and oxygen-rich environments prior to use. Oxidation that is either limited to the first few nanometers or through the bulk of the coating can result in seizure due to high initial coefficients of friction or component failure from excessive wear. High-sensitivity low-energy ion spectroscopy (HS-LEIS) and Rutherford backscattering spectrometry (RBS) are both used to understand the extent of oxidation throughout the first ~10 nanometers of the surface of pure sputtered nanocrystalline MoS 2 coatings after high-temperature aging and how it is impacted by the density of coatings as measured by RBS. Results show that low-density coatings (ρ = 3.55 g/cm 3 ) exhibit a more columnar microstructure and voiding, which act as pathways for oxidative species to penetrate and interact with edge sites, causing severe surface and subsurface oxidation. Furthermore, HS-LEIS of surfaces sheared prior to oxidation reveals that the oxidation resistance of low-density MoS 2 coatings can be significantly improved by shear-induced reorientation of the surface microstructure to a basal orientation and elimination of pathways for oxygen into the bulk through compaction of surface and subsurface voids.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxidation Activities

Slides for Oxidation Activities, oxidation rate, penetration/lathing, and strength after oxidation work. Also includes recent and current oxidation studies, background for rate behavior, strength behavior, density profile, and penetration measurements, oxidation resistant graphite coating development, and irradiated and unirradiated graphite oxidation rate behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Alloy designs for high temperature Mo-base systems

For high temperature applications Mo base alloy requirements include both superior structural performance and environmental resistance. To address these requirements alloys in the Mo-Si-B system and refractory multi-principal element alloys (RMPEA) are being developed that exhibit a promising potential, but also have some remaining challenges to improve ductility, lower density and enhance environmental resistance. In the Mo-Si-B system microstructures with a Mo solid solution (Moss) Mo 3 Si and Mo 5 SiB 2 (T2) phases have been the focus of attention. However, the Si solubility in the Moss phase diminishes the ductility and toughness. In order to address this issue a new design based upon Moss, Mo 2 B and T 2 phases lowers the Si solubility in the Moss to improve ductility while the T 2 phase maintains the oxidation performance. Selected additions of Al and Ti enable a density reduction to below 8 g/cm 3 . The RMPEA designs for Mo-rich alloys provide for excellent structural performance, but the complex oxidation products provide no protection. However, in this case a new coating design has been introduced that provides the required environmental resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A comparative review on cold sprayed cermet coatings and their applications in high temperature corrosion, oxidation and wear resistance

This review article explores the properties and bonding mechanisms specific to cold sprayed cermet coatings, highlighting its contrast with that of pure metals, and pure ceramics. The general cost structure of cold spraying is compared with other thermal spray techniques and the advantages are highlighted. Several cold sprayed cermet coatings with good corrosion, oxidation and wear resistance behavior in elevated temperatures show convincing potential for applications in power generation industries. The important factors that are attributed to producing highly functional cold sprayed cermet coatings are discussed. A strategic approach involving material, equipment, and application specific optimization of the cold spray process is currently relevant and of utmost importance to meet the coating requirements in several industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robust Dissimilar Metal Friction Welded Spool for Enhanced Capability for Steam Power Components (Final Program Report)

This project successfully demonstrated the feasibility and advantages of producing durable, friction-welded dissimilar-metal spools, both with and without transition pieces, as well as the use of advanced oxidation-protective coatings for steam power applications. The work encompassed the optimization and full-scale production of NFA tubing, overcoming manufacturing and processing challenges to achieve enhanced strength, creep, and fatigue properties validated by extensive microstructural characterization. Optimized welding techniques were developed and refined for joining dissimilar materials, resulting in defect-free welds optimized for both low- and high-pressure boiler circuits. Systematic evaluation of welding parameters, coupled with heat treatments, ensured reliable performance and minimized weld defects such as banding and cracking. Comprehensive mechanical and non-destructive testing, including tensile, bend, fatigue, and CT scanning, confirmed the superior integrity and durability of the friction-welded joints under representative service conditions. To address oxidation-related degradation, a range of protective alloy coatings—such as IN625, APMT, Duplex 2507, and FeCrAlY—were selected and evaluated for their ability to counteract oxide notch formation at dissimilar metal interfaces. These coatings demonstrated improved oxidation resistance and long-term stability under thermal cycling, thereby extending weld service life. Thermal cyclic testing and long-term studies captured the phase stability and diffusion behavior of coated and uncoated configurations. Validated models for low-cycle fatigue (LCF), creep, and thermal mechanical fatigue (TMF) were developed to predict component life and failure modes. These models confirmed that friction-welded configurations exhibited significantly enhanced performance compared to conventional gas-tungsten arc welding (GTAW), with up to 7× improvement in creep resistance and at least 2× enhancement in fatigue properties. The introduction of a tailored transition piece further reduced thermally induced strains, enhancing fatigue life. The results demonstrate a robust pathway for retrofitting existing steam fleet components and upgrading future equipment to deliver substantially improved cold-start cycling behavior and reduction of unplanned outages due to premature weld failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

An impermeable copper surface monolayer with high-temperature oxidation resistance

Despite numerous efforts involving surface coating, doping, and alloying, maintaining surface stability of metal at high temperatures without compromising intrinsic properties has remained challenging. Here, we present a pragmatic method to address the accelerated oxidation of Cu, Ni, and Fe at temperatures exceeding 200 °C. Inspired by the concept that oxygen (O) itself can effectively obstruct the pathway of O infiltration, this study proposes the immobilization of O on the metal surface. Through extensive calculations considering various elements (C, Al, Si, Ge, Ga, In, and Sn) to anchor O on Cu surfaces, Si emerges as the optimal element. The theoretical findings are validated through systematic sputtering deposition experiments. The introduction of anchoring elements to reinforce Cu–O bonds enables the formation of an atomically thin barrier on the Cu surface, rendering it impermeable to O even at high temperatures (400 °C) while preserving its intrinsic conductivity. This oxidation resistance, facilitated by the impermeable atomic monolayer, opens promising opportunities for researchers and industries to overcome limitations associated with the use of oxidizable metal films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Environmental Protection Coating System for Refractory Metal Alloys (EPCS for RMAs)

As part of ARPA-E’s Ultra High Temperature Impervious Materials Advancing Turbine Efficiency (UITIMATE) program, this project aims to develop an environmental protection coating system (EPCS) for refractory metal alloys (RMAs) – which will provide radical improvement in long term protection for ultra-high temperature refractory metal components in harsh gas-turbine environments. The drive for higher fuel efficiency and higher core power of gas turbines used in electric power generation and in aircraft propulsion requires higher peak operation temperatures. The temperature capability of state-of-the-art materials cannot meet the new requirements. Refractory metal alloys have desirable capabilities for achieving the required peak temperatures, but most of them are subject to oxidation in the gas turbine environment. Thus, there is a strong need to develop novel environmental protective coatings that enable the refractory metals to operate in an ultra-high temperature engine environment. This project is composed of four major technical innovations that can provide a potentially transformational solution in providing environmental protection for refractory metal alloys over a wide range of temperature. 1) Multi-layer self-healing environmental barrier coating (EBC) that provides protection against combustion gas environment. 2) Oxidation resistant diffusion barrier (DB) on the alloy surface to enhance coating stability. 3) Synergistic integration of the multi-layer self-healing EBC with the diffusion barrier to extend coating life. 4) Guidance of physics-based modeling to accelerate coating development and optimization. Our team has successfully developed a multi-layer self-healing environmental protection coating system (EPCS) that can provide oxidation protection for commercially available molybdenum based refractory metal alloys over a wide temperature range of up to 1600 °C for fuel-efficient gas turbine applications. The team also developed a multi-layer high temperature coating design tool to accelerate coating development and optimization based on physics-based modeling. The team also engaged RTX business unite, notable Pratt and Whitney, for future commercialization of this technology. The successful completion of this Phase I effort led to the selection of performing Phase II of the program. In Phase II, the team plans to apply the EPCS in the protection of a newly discovered molybdenum-based metal alloy which has the potential of superior high temperature properties to the commercial products. Th coating will be evaluated under test conditions and environment that mimic gas turbine operation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Holistic comparison of environmental barrier coating material candidates through design of a figure of merit

The first figure of merit for environmental barrier coating (EBC) materials was designed through a ranking system for material properties pertaining to established EBC failure modes in service. Seven past, present, and novel EBC candidate materials were used in the figure of merit design: SiO 2 , Ba 0.75 Sr 0.25 Al 2 Si 2 O 8 (BSAS), HfSiO 4 , Yb 2 Si 2 O 7 , Yb 2 SiO 5 , Yb 2 O 3 , and YbPO 4 . Utilizing compiled data from the literature, the presented figure of merit verified Yb 2 Si 2 O 7 as the state-of-the-art candidate with optimal EBC properties and inferred that YbPO 4 should be considered as a potentially viable EBC material candidate. Further, the figure of merit allows for a holistic comparison of EBC candidates and informs experimental and computational search efforts for next-generation complex EBCs. Clear knowledge gaps found through this work include CaO–MgO–Al 2 O 3 –SiO 2 (CMAS)-resistant coatings, EBC lifetimes before delamination, and oxidant diffusion rates in relevant EBC microstructures. It was shown that while some materials show promise for solving a single key failure mode for EBCs (i.e., CMAS reactivity), a community-wide goal should be placed on materials development to achieve acceptable resistance against all major failure modes, which are interconnected. Novel compositionally complex EBC materials, in addition to layered EBC architectures, show promise for the optimization of material properties for long-lifetime EBCs in combustion environments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Effect of Sulfuric Acid Anodization on the Electrochemical Properties of Aluminum Alloy AlSi 10 Mg Prepared by Selective Laser Melting

Aluminum alloy, AlSi 10 Mg, prepared by selective laser melt (SLM) fabrication was anodized in 9.8% sulfuric acid (Type II) at 15 V for a total of 23 min. Experiments were performed to study the potentiostatic anodization process and its effects on the oxide coating morphology, thickness, and electrochemical properties of the alloy. Prior to anodization, the alloy microstructure is composed of aluminum cells encapsulated in a silicon network. Anodizing the abraded and polished AlSi 10 Mg surface produced a porous oxide layer with a thickness of 5μm. The oxide coating weight was 698 ± 29 mg/ft 2 . The oxide coating forms in the aluminum cells that are isolated from one another by the silicon eutectic phase. In electrochemical tests, the anodic and cathodic potentiodynamic polarization currents were suppressed by factors of 15× and 215×, respectively, as compared to the unanodized controls. The data indicate the anodic oxide coating suppresses the cathodic more than the anodic reaction rate. Linear polarization resistance (R p ) values increased by 279× after anodization. The corrosion current density values (j corr ) decreased by 133× after anodization. Taken together, the electrochemical data indicate the anodic oxide coating (unsealed) increases the corrosion resistance of the SLM alloy by two orders of magnitude.

Electrochemistry↗
DOE OSTI2025

High-Temperature Active Magnetic Bearing Development for Supercritical CO 2 Machinery Applications

Hermetic machinery utilizing gas bearings for MW-scale supercritical CO 2 (sCO 2 ) machinery applications can have significantly lower power loss and enable improved cycle efficiency compared to conventional machinery with oil-lubricated bearings. Active magnetic bearings (AMBs) are another option anticipated to have similar power loss and load capacity to gas bearings as well as offering larger mechanical tolerances, the ability to tune properties, and high reliability due to lack of mechanical wear. AMBs also have proven commercial experience at MW-scale, though environments for high-temperature sCO 2 power cycle machinery conditions are novel. Besides the potential impact of AMBs for sCO 2 turbomachinery, the technology also offers promising benefits for steam and gas turbines for power generation, compressors and expanders for industrial heat and power, and in other oil and gas and space applications. The goals of this project were to conceptual design an AMB and perform material testing. Conceptual designs for radial and thrust AMBs were produced based on a hermetically-sealed sCO 2 machinery waste-heat recovery (WHR) application for sizing and loads, and choosing a target design temperature of 540°C useful for high-temperature sCO 2 turbines for concentrating solar power (CSP) applications. Conceptual designs were initially developed for multiple radial and thrust AMBs with spreadsheet-based calculations before selecting one of each to develop further using higher-fidelity design methods for magnetic and structural performance. It was found that the radial AMB at 540°C was feasible, but the thrust AMB needed to be limited to 315°C for high-speed operation. The decision for a reduced-temperature thrust AMB was the result of several significant conclusions: 1) Hiperco 50A, originally chosen for good magnetic performance at high temperature, had insufficient strength for high-speed operation, so it was replaced with 17-4 PH. 2) The reduced magnetic performance from 17-4 PH yielded a larger bearing size, reducing the strength margin. 3) This ultimately led to a creative design implementing a more-compact E-core topology, compared to the original (conventional) C-core, and an integral shaft-disk with Hirth joint connection. These conceptual designs are unique for the size and temperature in CO 2 , relevant for MW-scale CSP applications. Long term, high temperature test data was generated for several materials, filling a void in the current body of literature. Corrosion and magnetic performance measurements were produced for PM materials (Alnico 5-7C, Alnico 9C, and SmCo) with and without nickel-coating for environments of high-temperature CO 2 up to 550°C at atmospheric pressure and 450°C at 103 bar for up to 6,000 hours. Corrosion measurements were also produced for Hiperco 50, a SM material relevant for AMB laminations, with and without C5 coating. Comparisons were also made for 450°C and 550°C, atmospheric pressure air exposures up to 5,000 hours. Results generally show that coatings can be effective at improving oxidation resistance of the bare materials, and Alnicos generally outperformed SmCo after high-temperature exposure. In addition to technical feasibility demonstrated by the design, economic feasibility was demonstrated by updating the TEA from the reference machine, re-evaluating it with CAPEX and OPEX to reflect estimated changes from process-lubricated bearings to AMBs. AMBs were shown to be comparable in performance to process-lubricated bearings, still showing a notable improvement over conventional machinery architecture with oil-lubricated bearings.

42 ENGINEERING↗
DOE OSTI2024

Advanced Coating Compositions and Microstructures to Improve Uptime and Operational Flexibility in Cyclic, Low-Load Thermal Utility Plants

GE, the University of Tennessee, and Oak Ridge National Laboratory collaborated from 2020 to 2023 developing two key technologies for improving the viability of fuel switching and load following in thermal utility plants: a) cost-effective weld overlay compositions for boiler tubing b) cathodic arc coatings that deliver improvements in both erosion resistance and oxidation resistance in high temperature steam for HP turbine blades The team worked through a robust, logical project map to de-risk these two technologies and advance them from TRL 3 to TRL 6. For the cost-effective weld overlay, the team developed a ferritic filler material which was fabricated at a vendor for 18% the average market cost of Inconel 625 wire, had a corrosion rate 3x lower in conditions simulating a biomass-fired superheater and 10x lower in conditions simulating a coal-fired superheater, and was fabricated into prototype overlaid tubing that passed ASME requirements including transverse bending, dye penetrant inspection, and ASTM G-76 evaluation. For the cathodic arc coatings applied to steam turbine blades, the team developed a novel composition that was successfully transferred to a qualified vendor. The vendor was able to produce coated prototypes with 4x the as-deposited erosion resistance and 10.4x the post-steam-exposure erosion resistance of the TiN coating the vendor currently applies on GE steam turbine components, without significantly increasing process cost. These coated prototypes also passed a GE inspection and showed favorable performance in high temperature erosion, nanoindentation, sliding wear, scratch adhesion, and high cycle fatigue testing. If successfully deployed by GE, it is anticipated that the technologies will enable the following: • 25%-50% increase in time between outages for both boilers and HP turbines. • 50% decrease in cost for weld overlay on a per foot basis relative to todays NiCr alloys. • Adequate oxidation resistance and erosion for HP turbine inlet steam at >620°C and >220 bar. • No need for changes in component supply chain or any notable Capital Expenditures. 5 Decreasing component cost, increasing performance, and extending time between outages represent direct value propositions to GE and their customers. For the American consumer, these objectives translate into increased grid reliability (fewer unexpected outages), decreased Levelized Cost of Electricity, and improved environmental health (low-loading/load following to accelerate penetration of renewables). The results also have implications for wear resistant tooling, wire arc additive manufacturing, more durable components for syngas cleanup, and deployment of more efficient thermochemical pathways for carbon negative fuel production

09 BIOMASS FUELS↗
DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dynamic oxidation of (Mn,Co) 3 O 4 -Coated interconnects for solid oxide electrolysis cells

Solid oxide electrolysis cell stacks are expected to experience dynamic conditions when using renewable electricity derived from wind or solar power. To address this scenario, (Mn,Co) 3 O 4 (MCO)-coated Crofer 22 APU interconnect coupons are subjected to thermal cycling, and intermittent current density, with gas compositions relevant to high-temperature electrolysis (elevated steam:hydrogen ratio and oxygen content). Defects are also intentionally introduced in the MCO coating, to assess whether the difference in oxidation properties of the adjacent coated and uncoated (defective) surfaces causes sufficient stress to damage the protective oxide scale. Specimens with defects are subjected to oxidation for 1000 h at 800 °C, or thermal cycling. Before thermal cycling, some specimens are pre-oxidized to create a thick oxide scale to mimic the scale thickness expected after ~30 kh operation. In all cases, the coating and oxide scale remain well adhered with no cracking observed. Area-specific resistance (ASR) is monitored in both single-atmosphere and dual-atmosphere conditions, and the ASR is stable and is not impacted by dynamic cycling of the current density. Finally, this work provides confidence that the MCO coated interconnect will function as needed in dynamic operation conditions, even with coating defects.

08 HYDROGEN↗
DOE OSTI2025

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗
DOE OSTI2025

The impact of chromium coatings on Zircaloy cladding deformation behavior under reactivity-initiated accident-like mechanical loading conditions

A reactivity-initiated accident (RIA) occurs when a control rod ejection or control blade drop causes an increase in the fission rate. The injection of energy results in an increase in fuel temperature which in turn causes rapid thermal expansion of the fuel pellet. This thermal expansion may result in pellet-cladding mechanical interaction (PCMI) in which the fuel imparts a mechanical strain to the cladding. PCMI may cause the cladding to fail, and thus, the mechanical response of cladding due to PCMI must be investigated when characterizing new cladding materials. Chromium-coated Zircaloy-4 is a near-term accident-tolerant fuel cladding that exhibits improved high-temperature oxidation resistance. Modified burst testing was utilized to experimentally simulate the effects of PCMI on both uncoated and chromium-coated Zircaloy cladding samples at hot zero power conditions. Samples were coated using either cold spraying or physical vapor deposition to understand the differences in behavior that the coating application method may cause. Digital image correlation was used to analyze images of the deforming specimens to extract the in-situ strain behavior of the cladding. The uncoated specimens burst at hoop strains ranging from 8.8 % to 17.2 %. The cold-spray chromium-coated Zircaloy specimens burst at hoop strains of 7.0 % to 11.0 %. The physical vapor deposition coated tubes burst at hoop strains of 9.1 % to 11.5 %. These results indicate that the chromium coating causes a loss in the ductility of the cladding. Furthermore, the higher burst hoop strains of the physical vapor deposition-coated samples relative to the cold-spray samples indicate that the cold-spraying technique causes more of a loss in ductility than physical vapor deposition. All samples burst at higher hoop strains than those expected to occur in an RIA for fresh cladding.

Accident-tolerant fuel↗