Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPELLANT TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Quasi-steady testing approach for high-power Hall thrusters

Hall effect thrusters operating at power levels in excess of several hundreds of kilowatts have been identified as enabling technologies for applications such as lunar tugs, large satellite orbital transfer vehicles, and solar system exploration. These large thrusters introduce significant testing challenges due to the propellant flow rate exceeding the pumping speed available in most laboratories. Even with proposed upgrades in mind, the likelihood that multiple vacuum facilities will exist in the near future to allow long duration testing of high-power Hall thrusters operating at power levels in excess of 100 kW remains extremely low. In this article, we numerically explore the feasibility of testing Hall thrusters in a quasi-steady mode defined by pulsing the mass flow rate between a nominal and a low value. Here, our simulations indicate that sub-second durations available before the chamber reaches critical pressure are sufficiently long to achieve the steady-state current and flow field distributions, allowing us to characterize thruster performance and the near plume region.

42 ENGINEERING↗
DOE OSTI2022

5.1.6 Demo #6: NanoStitch (NAWAStitch) Multifunctional Composites Trade Validation

The overall objective of the NanoStitch Multifunctional Composites Trade Validation Demonstration project was to determine the value proposition of adding NanoStitch to rapid-cure composite systems for structures used in the expanding sector of advanced air mobility (AAM) and specifically electric vertical take-off and landing (eVTOL) aircraft. The expected value proposition was stronger composite parts, with new multifunctional attributes, that are lower cost to fabricate and maintain. NanoStitch is a new composite innovation where a contiguous vertically aligned carbon nanotube (VACNT) forest is located between each ply of a laminate composite resulting in improved mechanical properties as well as other multifunctional properties such as enhanced thermal and electrical conductivity. NanoStitch was originally distributed by N12, later acquired by NAWA Technologies, now called NAWAStitch, and henceforth referred to in this document as NAWAStitch. Two significant evaluations were framed to help meet the overall objective. First, was Task 1 to evaluate the effects that adding NAWAStitch to a rapid cure material system would have on the mechanical and processing properties of the material. Second, was Task 2 to evaluate the workability of adding NAWAStitch to practical flight demonstration articles. From previous research, it was already known that the application of NAWAStitch to a composite structure can enhance the mechanical properties of that structure. However, this project will help the engineering community understand those benefits and the basic structural strength values to apply when incorporating NAWAStitch material into composite structure that utilizes a rapid-cure resin system, which is novel. Testing showed that by adding NAWAStitch to the prepreg, most material properties were improved because the VACNTs strengthened the resin to fiber interface, and the interface itself, between plies. For example compression strength improved by more than 20%, and erosion resistance by more than 50%. The UDRI team identified two flight demonstration articles through discussions with Aurora Flight Sciences (Aurora) and reviewing literature on air mobility and the eVTOL market. The demonstration articles were a thin skin honeycomb panel and a section from an eVTOL propeller blade. The manufacturing and testing trials of the demonstration articles were as follows: • NAWAStitch added no manufacturing complexity or detriment to the article physical qualities, while at the same time added multifunctional properties such as enhanced rain erosion and electrothermal de-icing besides enhanced mechanical properties • VACNTs did not increase or hurt the mechanical properties of the interface between honeycomb core materials and the thin skin face sheet • Demonstrated successful de-icing function in an eVTOL propeller meeting real-world specifications in uniformity and endurance • Multifunctional eVTOL propeller cost analysis showed a cost savings of at least 67 % for a single propeller blade with multifunctional de-icing capability and improved mechanical properties which equates to a potential savings of $10,116 per eVTOL aircraft with six three-bladed propellers Overall, the results of this project can provide additional tools for the composite industry to optimize energy efficiency through faster and stronger composite parts that are lower cost to fabricate and maintain. Additionally, the results of this effort can help US industry like NAWA America set the stage for rapid growth and establishment of a manufacturing facility in Ohio. The project has given NAWA America the basic understanding of how the addition of VACNTs to a composite structure can affect the mechanical properties and hence point them to potential commercial applications. The project has also provided Teijin Carbon US with another potential material application for their rapid cure materials that are manufactured at the Renegade facility in Miamisburg, OH.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Prototype High-Voltage Pulsed Power Supply for Control of the ITER Shattered Pellet Injection System Flyer Plate Valve

A high-voltage pulsed power supply (HVPPS) has been designed, prototyped, and tested for driving an eddy current actuated propellant valve for the International Thermonuclear Experimental Reactor (ITER) disruption mitigation system. The high-voltage (HV) dc supply output voltage is software programmable, and the energy storage capacitor bank can be readily reconfigured as 200, 400, 600, and 800 μ F, enabling testing and optimization of both the valve drive and valve systems. Multiple system parameters are monitored before, during, and after each firing of the valve. The system parameters are both displayed and stored for further analysis. Control of the setup, firing sequence, and data collection is automated using a LabVIEW-based control program. The programmability and reconfigurability of this system collectively provide a flexible and robust platform for system refinement and optimization. In this article, a summary of the system will be provided including operational sequences, HV switching and associated triggering methods and circuits, and results measured while firing a solid frozen pellet. Additionally, planned refinement activities toward meeting all requirements for ITER integration will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Design and out-of-pile testing of a novel irradiation experiment vehicle to support qualification of nuclear thermal propulsion components

Fission power systems have demonstrated higher thermal energy density per unit mass than chemical systems. High mass specific energy density offers advantages in space thermal propulsion applications. In the 1960s, nuclear thermal propulsion (NTP) development included the ROVER/NERVA program, in which full-scale prototype reactors were tested on the ground using hydrogen as the reactor coolant and propellant. NTP systems are being revisited, with expectations of improved performance resulting from improved fuel materials, allowing propellant temperatures near 2,800 K and over 20 thermal propulsion cycles. An apparatus has been developed to test NTP fuel materials in a research reactor at temperature and in a radiation environment typical of the NTP application. Here, this paper presents the design constraints, preliminary scoping thermal analysis, and basic thermal qualification testing for the out-of-pile experiment set apparatus, or OUTSET.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Study of the Design and Characteristics of a Modified Pulsed Plasma Thruster with Graphite and Tungsten Trigger Electrodes

The paper presents experimental results for a modified pulsed plasma thruster (PPT) with solid propellant, using a coaxial anode–cathode design. Graphite from pencil leads served as propellant, and a tungsten trigger electrode was tested to reduce carbonization effects. Experiments were performed in a vacuum chamber at 0.001 Pa, employing diagnostics such as discharge current/voltage recording, power measurement, ballistic pendulum, time-of-flight (TOF) method, and a Faraday cup. Current and voltage waveforms matched an oscillatory RLC circuit with variable plasma channel resistance. Key discharge parameters were measured, including current pulse duration/amplitude and plasma channel formation/decay dynamics. Impulse bit values, obtained with a ballistic pendulum, reached up to 8.5 μN·s. Increasing trigger capacitor capacitance reduced thrust due to unstable “pre-plasma” formation and partial pre-discharge energy loss. Using TOF and Faraday cup diagnostics, plasma front velocity, ion current amplitude, current density, and ion concentration were determined. Tungsten electrodes produced lower charged particle concentrations than graphite but offered better adhesion resistance, minimal carbonization, and stable long-term performance. The findings support optimizing trigger electrode materials and PPT operating modes to extend lifetime and stabilize thrust output.

Faraday cup↗
DOE OSTI2023

Advanced Compact Generation Module with Fish Safe Runner Technology

Hydropower is an important contributor of stable, load-leveling renewable energy to our national grid. Increasingly, the development of new hydropower facilities or the retrofit of existing ones hinges not only on minimizing costs but also environmental impact. In this report, the analysis and testing of a modular and scalable low-head hydropower generation design using Natel Energy’s Restoration Hydro Turbine is described. This design leverages many established industry approaches for compactness and efficiency while simultaneously allowing for safe downstream fish passage through the turbines themselves. This unique approach reduces overall hydropower facility costs and enables a simpler inclusive method of project design and operation. To assess this design, mechanical and fluid computational analyses were used to study and optimize key parameters. Passage tests of important migratory species (salmonids, American eel) were conducted through representative turbines. The unique propeller geometry of the fish-safe Restoration Hydro Turbine was subjected to detailed design and testing using advanced manufacturing composite techniques. Comprehensive module cost models were developed and assessed alongside hydraulic efficiency. The results of this project show promising and economical applications for downstream passage offish through Restoration Hydro Turbine modules.

13 HYDRO ENERGY↗
DOE OSTI2024

Modifications to the JET Shattered Pellet Injector to Optimize Disruption Mitigation Experiments for Supporting ITER’s DMS Design

Shattered pellet injection (SPI) experiments on Joint European Torus (JET) are an important element in determining the physics basis for mitigating disruptions in ITER. Here, the initial design of the JET SPI system included three barrels to produce pellets with diameters of 4.5, 8.1, and 12.5 mm. The variability of the pellet speed by operating with and without a mechanical punch was limited and led to poor pellet integrity, so the mechanical punch was removed. Fragment size distribution is a function of pellet speed and the desire to change the resulting fragment size distribution was not originally a requirement. After the first set of SPI experiments on JET, different pellet sizes were considered to enable dual injection experiments with identical pellet diameters. It was also determined that speed control is necessary to improve experimental repeatability and to determine how the fragment size distribution impacts mitigation performance. Two barrels were fabricated to form pellets of 10 mm diameter and a third to form an 8.1 mm diameter pellet. New propellant valves were also fabricated and characterized to improve repeatability and overall performance. To have fine control of pellet speed, inserts to reduce the breech volume were fabricated and installed. Laboratory testing was conducted to ensure pellet release and provide a comparison of propellant gas delivered versus pellet speeds for a range of pellet types and mixtures. This article will also discuss how lessons learned from the JET SPI modifications can be applied to other SPI systems, such as the ITER SPI system, as controlling pellet release with the least amount of propellant gas is essential for optimal SPI effectiveness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

The Plant Microbiome: From Ecology to Reductionism and Beyond

Methodological advances over the past two decades have propelled plant microbiome research, allowing the field to comprehensively test ideas proposed over a century ago and generate many new hypotheses. Studying the distribution of microbial taxa and genes across plant habitats has revealed the importance of various ecological and evolutionary forces shaping plant microbiota. In particular, selection imposed by plant habitats strongly shapes the diversity and composition of microbiota and leads to microbial adaptation associated with navigating the plant immune system and utilizing plant-derived resources. Reductionist approaches have demonstrated that the interaction between plant immunity and the plant microbiome is, in fact, bidirectional and that plants, microbiota, and the environment shape a complex chemical dialogue that collectively orchestrates the plantmicrobiome. Finally, the next stage in plant microbiome research will require the integration of ecological and reductionist approaches to establish a general understanding of the assembly and function in both natural and managed environments.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Analysis of the Shattered Pellet Injection Fragment Plumes Generated by Machine Specific Shatter Tube Designs

Shattered pellet injector systems have been installed on DIII-D, JET, and KSTAR and used to experimentally determine the effectiveness of the shattered pellet injection (SPI) process in mitigating the deleterious effects of a tokamak plasma disruption. Pellets are fired, and before entering the plasma, strike a bent tube known as a shatter tube causing the pellet to shatter. The process of pellet fragmentation is a chaotic process that can be described in terms of fragment size distribution through a statistical model that incorporates the effects of the pellet material and impact characteristics. In addition to the fragment size distribution, the shatter plume has other characteristics of interest, such as a fragment velocity distribution and temporal mass evolution. The fragment velocity distribution is important because it is needed to accurately model the spread and location of the ablation and the deposition of impurities in the plasma over time. The temporal mass evolution is necessary to determine the time-resolved delivery of mass to the plasma.Due to installation constraints, the shatter tube currently installed on JET has a unique geometry with a modest S-bend followed by a 20-deg bend at the end of the tube. The DIII-D and KSTAR shatter tube design is a simple tube bent through an angle of 20 deg followed by a straight section. The resulting shatter sprays from the JET shatter tube and a 20-deg miter bend shatter tube were experimentally characterized for various pellet materials and speeds. Laboratory testing of these shatter tubes allows for the use of fast cameras to capture the fragment spray traveling through a large vacuum chamber. These high-speed videos of the shatter plumes allow the fragment size distribution, temporal mass evolution, and velocity distribution of the fragments within the plume to be determined. Overall, this paper presents a comparison of the unique geometry of the JET shatter tube to the miter bend geometries used for shattering and some insight into the variables that may be adjusted to produce the optimal shatter spray. The impact of entrained propellant gas on the resulting shatter spray was examined during testing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Impact Testing Theories and Techniques Employed at the TA-III Mechanical Shock Complex

We present theories and techniques to support safe, predictable, and efficient impact testing at the Sandia National Laboratories TA-III Mechanical Shock Complex (MSC), located in Building 6570. The two testing instruments used at the MSC are the 20-inch actuator, which is a launcher that propels sleds down an indoor track, and an indoor 6-in bore compressed-gas powered cannon. The theories and techniques presented derive from basic mechanical engineering principles but are significantly informed and validated by testing experience at the MSC.

42 ENGINEERING↗
DOE OSTI2022

Sugar loading is not required for phloem sap flow in maize plants

We report phloem transport of photoassimilates from leaves to non-photosynthetic organs, such as the root and shoot apices and reproductive organs, is crucial to plant growth and yield. For nearly 90 years, evidence has been generally consistent with the theory of a pressure-flow mechanism of phloem transport. Central to this hypothesis is the loading of osmolytes, principally sugars, into the phloem to generate the osmotic pressure that propels bulk flow. Here we used genetic and light manipulations to test whether sugar import into the phloem is required as the driving force for phloem sap flow. Using carbon-11 radiotracer, we show that a maize sucrose transporter1 (sut1) loss-of-function mutant has severely reduced export of carbon from photosynthetic leaves (only ~4% of the wild type level). Yet, the mutant remarkably maintains phloem pressure at ~100% and sap flow speeds at ~50–75% of those of wild type. Potassium (K+) abundance in the phloem was elevated in sut1 mutant leaves. Fluid dynamic modelling supports the conclusion that increased K+ loading compensated for decreased sucrose loading to maintain phloem pressure, and thereby maintained phloem transport via the pressure-flow mechanism. Furthermore, these results suggest that sap flow and transport of other phloem-mobile nutrients and signalling molecules could be regulated independently of sugar loading into the phloem, potentially influencing carbon–nutrient homoeostasis and the distribution of signalling molecules in plants encountering different environmental conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultra-light antennas via charge programmed deposition additive manufacturing

Abstract The demand for lightweight antennas in 5 G/6 G communication, wearables, and aerospace applications is rapidly growing. However, standard manufacturing techniques are limited in structural complexity and easy integration of multiple material classes. Here we introduce charge programmed multi-material additive manufacturing platform, offering unparalleled flexibility in antenna design and the capability for rapid printing of intricate antenna structures that are unprecedented or necessitate a series of fabrication routes. Demonstrating its potential, we present a transmitarray antenna composed of an interconnected, multi-layered array of dielectric/conductive S-ring unit cells, reducing 94% mass of conventional antenna configurations. A fully printed circular polarized transmitarray system fed by a source and a Risley prism antenna system operating at 19 GHz both show close alignment between testing results and numerical simulations. This printing method establishes a universal platform, propelling discovery of new antenna designs and enabling data-driven design and optimizations where rapid production of antenna designs is crucial.

Science & Technology - Other Topics↗
DOE OSTI2020

Operability of a Natural Gas–Air Rotating Detonation Engine

A combustor was developed to operate with natural gas and air as the primary propellants at elevated chamber pressures and air preheat temperatures representative of land-based power generation gas turbine engines. Detonation dynamics were studied to characterize the operability of rotating detonation-based pressure gain combustion systems for this application. Measurements of chamber wave dynamics were performed using high-frequency pressure transducers and high-speed imaging of broadband combustion chemiluminescence. The rotating detonation engine was tested with two injector configurations across a broad range of mass flux (200–500 kg/m 2 /s), equivalence ratio (0.85–1.2), and oxygen mass fraction (23.2–35%) conditions to determine the effect of operating parameters on the propagation of detonation waves in the combustor. Wave propagation speeds of up to 70% of the mixture Chapman–Jouguet detonation velocity and chamber pressure fluctuations greater than 4 times the mean chamber pressure were observed. Supplementing the air with additional oxygen, varying the equivalence ratio, and enriching the fuel with hydrogen revealed that combustor operability is sensitive to the chemical kinetics of the propellant mixture. Comparing the operational trends of the two injector configurations suggests that one design mixes the incoming propellants more effectively. Although most test conditions exhibited counter-rotating detonation waves within the chamber, the injector design with superior mixing characteristics was able to support single-wave propagation.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Novel Segregated Solid Propulsion System with Separately Stored Fuel and Oxidizer

Abstract The development and experimentation of a solid propulsion concept consisting of separate hydrogen‐rich solid propellant and solid oxidizer grains is presented. This system consists of an extremely fuel‐rich solid propellant, which, once ignited, undergoes a self‐sustaining decomposition to release fuel‐rich product gases, which are particularly rich in hydrogen gas. These relatively high‐temperature gases subsequently react with a solid oxidizer grain stored downstream. Progress in high‐nitrogen materials has allowed for the synthesis of fuel‐rich compounds that can store significant amounts of hydrogen, with little or no bound oxygen. With these new developments in propellant chemistry, a unique segregated propulsion system has been developed, creating an all‐solid propulsion system that combusts analogously to a reverse hybrid rocket system. Because of the physical separation of fuel and oxidizer, a higher level of safety is achieved which concurrently allows for the utilization of higher energy ingredients without the penalty of higher sensitivity. Theoretical performance calculations and experimental data have shown the potential for this system to compete with existing composite rocket propellants while having significant benefits in terms of safety, toxicity, and mission space. This paper presents a detailed overview of the conception, development, and testing of this propulsion system.

42 ENGINEERING↗
DOE OSTI2023

Post-irradiation examination of the Sirius-1 nuclear thermal propulsion fuel test

Nuclear Thermal Propulsion (NTP) systems hold promise in reducing transit times for exploration of the solar system by both crewed and uncrewed missions. NTP systems currently under investigation include a once-through high-temperature gas-cooled fission reactor to provide thermal energy to heat the coolant, which also serves as the propellant. The fuel system consists of angular UN fuel particles dispersed in a matrix of W/Re, creating a ceramic and metallic composite or cermet, which has been irradiated in Idaho National Laboratory's (INL) Transient Reactor Test Facility (TREAT). This enabled evaluation of these materials under representative nuclear heating rates (~95 K/s) and peak surface temperatures (~2527 K). Further, these surface conditions were indicative of achievement of the target peak internal temperature of approximately 2850 K. These tests named Sirius-1 (UN–W/Re), have been irradiated and this paper will present post-irradiation examination results. The Sirius-1 test produced minor, stable cracks in the fuel specimen and spalling of surface material. Volatilized uranium ‘soot’ was found deposited on the inner wall of the irradiation capsule indicating loss of some fissile material from the fuel specimen. Spalling from the surfaces was also noted upon visual inspection. Uranium diffusion from the fuel particles resulted in the formation of U/Re phases and the production of a laminar microstructure on the edge of the fuel system. Overall, the specimen was stable and remained within a coolable geometry upon conclusion of multiple thermal cycles to prototypical operating temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

A view on the current and future impact of research reactors

Full text of publication follows. The current fleet of nuclear research reactors worldwide is nearly 70 years old. These reactors have proven to be extremely valuable tools of nuclear science and engineering with a broad and interdisciplinary impact. To date, research reactors are utilized as tools for understanding the physics, operations, and safety of nuclear fission systems. In addition, they are used as intense sources of radiation in support of irradiation testing and nondestructive examination of materials. As this fleet of reactors ages, an urgent need exists to establish new facilities that can propel the benefit of these reactors into the 21. century. In fact, an opportunity exists to build research reactors based on technology concepts that are being considered for nuclear energy reactors. This may include high temperature gas cooled and/or molten salt based advanced and micro reactor concepts. Such future reactors should be designed to maintain the broad utility of current reactors in research and education. However, modern research reactors can be purposefully designed and instrumented to access neutronic and thermal hydraulic information that would support the development and validation of reactor multi-physics modeling and simulation techniques. In this case, the entire phenomenological paradigm of the reactor may be captured to understand the neutronic multiscale and its impact on operations and safety. Moreover, the generated data can be channeled to drive anticipatory examination of the state of the reactor. In general, a symbiotic relation may be envisioned between the modern research reactor and power reactor fleets, which could facilitate the safe and efficient implementation of clean nuclear energy. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Shear and combustion characterization of printable ammonium perchlorate composite propellant formulations

Seven formulations of ammonium perchlorate composite propellant (APCP) are developed and their properties relevant for successful additive manufacture are characterized. Extrusion in a custom-built 3D printing system and spindle viscometry are used to collect viscosity measurements of curing primary and non-curing secondary versions of the formulations. The formulations that behave similarly to a Bingham plastic, with apparent viscosities between 4 and 8 thousand Pa*s at 30 minutes post-mix, are determined to be most suitable for printing applications. Measurements of one material show a yield stress of 1 kPa. Ambient pressure burn rates of 2.0–2.9 mm/s were measured for the compositions tested. All measured burn rates were comparable to the lower end of typical burn rates for APCP. In conclusion, the results of the characterization demonstrate a propellant suitable for use in a 3D printing system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Space Nuclear Power Autonomous Control Algorithm and Control Element Test Bed

Nuclear thermal rockets are currently NASA’s preferred option for use in a manned mission to Mars in the 2040s. The communication delay between an Earth ground station and a spacecraft heading toward Mars can be up to 20 min. Therefore, controlling the nuclear rocket engine would require either a full-time reactor operator on the mission or an autonomous control system for the reactor. The latter idea of making space nuclear reactors fully autonomous has drawn more interest from stakeholders, but such an autonomous control system must be rigorously tested and validated before it is certified for human use. The cost of a full ground test for a space nuclear reactor is tremendous, so a nonnuclear mock reactor test bed was created to test and validate control elements and control algorithms for space nuclear reactors. The test bed consists of control element hardware that inputs physical measurement data into a reactor emulator to produce the reactor’s performance under steady-state, transient, and fault conditions. The control element hardware consists of six full-sized control drums equipped with servo drives and motors and is instrumented with optical encoders, resolvers, and torque sensors for drum movement characterization. In addition to the drums, a two-phase flow loop was designed and built to mimic the valves and turbomachinery associated with the propellant flow through a nuclear thermal rocket engine; components such as pressure sensors, flow meters, thermocouples, and tachometers are instrumented throughout the loop to characterize the fluid flow, valve, and turbomachinery behavior of the system. The data from the physical hardware (e.g., drum position, propellant flow rates) are input to a nuclear reactor simulator to determine the actual nuclear reactor parameters, and the data are sent back to a control algorithm to complete the control loop. The ability to conduct numerous tests of the control systems and autonomous algorithms can help validate the instrumentation and control aspects for a space nuclear reactor for every possible fault situation.

Wilson, Brandon↗