Waste derived polysulphide coating on fly ash as fillers in plastic composite
Not provided.
Construction & Building Technology↗
SEARCH · Search NASA
Results for “Plastic filler”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Control of volume resistivity in inorganic organic separators
Control of resistivity in NASA inorganic-organic separators is achieved by incorporating small percentages of high surface area, fine particle silica with other ingredients in the separator coating. The volume resistivity is predictable from the surface area of filler particles in the coating. The approach is applied to two polymer- plasticizer -filler coating systems, where the filler content of each is below the generally acknowledged critical pigment volume concentration of the coating. Application of these coating systems to 0.0254 cm thick (10-mil) fuel cell grade asbestos sheet produces inexpensive, flexible, microporous separators that perform as well as the original inorganic-organic concept, the Astropower separator.
Sheibley, D. W.↗
Control of volume resistivity in inorganic-organic separators
Control of resistivity in NASA inorganic-organic separators is achieved by incorporating small percentages of high surface area, fine-particle silica with other ingredients in the separator coating. The volume resistivity appears to be predictable from coating composition, that is, from the surface area of filler particles in the coating. The approach has been applied to two polymer-'plasticizer'-filler coating systems, where the filler content of each is below the generally acknowledged critical pigment volume concentration of the coating. Application of these coating systems to 0.0254 cm thick (10 mil) fuel-cell grade asbestos sheet produces inexpensive, flexible, microporous separators that perform at least as well as the original inorganic-organic concept, the Astropower separator.
Sheibley, D. W.↗
Hovering Performance of a Helicopter Rotor Using NACA 8-H-12 Airfoil Sections
A helicopter rotor employing an NACA 8-H-12 airfoil section has been tested on the Langley helicopter test tower. Two blade surface conditions were investigated, first with a filled blade which was within 0.002 inch of true airfoil shape obtained by use of plastic filler, and second with the filler removed resulting in a surface condition within 0.020 inch of true airfoil shape. Tests were conducted for the two sur-face conditions at a tip speed of 455 feet per second and over a tip-speed range from 455 to 650 feet per second for the blades with filler removed. The NACA 8-H-12 blades with the filled surface showed an aver-age reduction of 6 to 7 percent in total torque coefficients.
Robert D Powell, Jr↗
Effect of matrix plasticizing conditions and filler interfacial properties on the percolation threshold of polymer-carbon composites
Explore the source record for details and available documents.
electronic nose polymer-carbon composite molecular↗
Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites
In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.
01 COAL, LIGNITE, AND PEAT↗
In situ investigation of high-pressure hydrogen-induced swelling in elastomers and its correlation with material properties
The resistance of elastomeric materials to high-pressure hydrogen-induced damage is essential for ensuring the reliability of hydrogen infrastructure. Here, in this study, we systematically investigated the swelling behavior and hydrogen transport properties of four elastomer types – EPDM, NBR, FKM, and HNBR – using a custom in-situ view cell system capable of real-time monitoring during decompression from pressures up to 96.5 MPa. Each elastomer was formulated with and without fillers and plasticizers to assess the effects of formulation on swelling response. Thermal desorption analysis (TDA) was employed to determine equilibrium hydrogen content and diffusion coefficients, providing insight into gas uptake and mobility within each material. Correlation analyses using Pearson and Spearman coefficients revealed that the diffusion coefficient showed a stronger relationship with swelling behavior than hydrogen content, highlighting the dominant role of hydrogen mobility. Filled elastomers, particularly those with carbon black, consistently showed reduced swelling due to enhanced stiffness and reduced diffusivity. These results deepen our understanding of diffuso-mechanical interactions in elastomers and support the rational design of sealing materials for high-pressure hydrogen systems.
EPDM↗
Alkaline battery, separator therefore
An improved battery separator for alkaline battery cells has low resistance to electrolyte ion transfer and high resistance to electrode ion transfer. The separator is formed by applying an improved coating to an electrolyte absorber. The absorber, preferably, is a flexible, fibrous, and porous substrate that is resistant to strong alkali and oxidation. The coating composition includes an admixture of a polymeric binder, a hydrolyzable polymeric ester and inert fillers. The coating composition is substantially free of reactive fillers and plasticizers commonly employed as porosity promoting agents in separator coatings. When the separator is immersed in electrolyte, the polymeric ester of the film coating reacts with the electrolyte forming a salt and an alcohol. The alcohol goes into solution with the electrolyte while the salt imbibes electrolyte into the coating composition. When the salt is formed, it expands the polymeric chains of the binder to provide a film coating substantially permeable to electrolyte ion transfer but relatively impermeable to electrode ion transfer during use.
Schmidt, George F.↗
Structure and Flow-Viscosity of Filled-Polymer-Based 3D Printing Ink: Exploration through Coarse-Grained Molecular Dynamics
The addition of nanofiller particles to a polymer matrix has long been known to enhance or modify the composite’s mechanical and rheological properties. However, quantitatively capturing such changes with molecular level simulations remains computationally challenging. Toward that goal, we performed coarse-grained molecular dynamics of a nanocomposite system at a fixed (25 vol %) filler loading under nonspecific, weak polymer–filler interactions representative of a broad class of technologically important materials. We report several interesting results, including: (1) the equilibrium chain-configuration remains Gaussian-like as in an unfilled melt; (2) smaller filler particles display a stronger tendency to cluster; (3) larger fillers act as plasticizers by reducing the entanglement density and accelerating the chain mobility; and (4) fillers enhance the tensile response modulus, with the effect being stronger for larger particles. We also simulate cluster breakup, yielding, and elongational flow under an applied time-linear tensile strain and study the flow viscosity as a function of filler-size and chain-length.
Materials science↗
Influence of functional additives, fillers, and pigments on thermal and catalytic pyrolysis of polyethylene for waste plastic upcycling
Pyrolysis offers a relatively green and economical method to convert waste plastics into valuable chemicals and fuels without the need for harmful solvents, toxic chemicals, or costly high-pressure reactors. Despite its popularity among chemical upcycling technologies, industrial adoption suffers from feedstock heterogeneity, low-quality products, and catalyst deactivation. Most plastics in our daily lives are formulated with functional additives, fillers, and colorants. These additives remaining in end-of-life waste streams increase feedstock heterogeneity, creating a challenging issue in recycling plastics. Still, the potential impacts of additives on the chemical upcycling of plastics have been poorly understood. In this study, polyethylene compounded with a range of widely used additives (antioxidants, stabilizers, pigments, fillers, slip agents, and flame retardants) was subjected to both thermal pyrolysis and catalytic pyrolysis in different catalyst-to-feedstock contact modes. It showed that many inorganic additives, such as talc, kaolin, CaCO 3 , TiO 2 , carbon black, and zinc stearate, facilitated polymer decomposition during pyrolysis, increasing light hydrocarbons while also promoting aromatic and carbon residue formation. Conversely, antioxidants and stabilizers inhibited depolymerization, favoring heavier hydrocarbons. During catalytic pyrolysis with HZSM-5 zeolite, additives strongly enhanced aromatic and catalytic coke formation, especially when there was direct contact between plastics and catalysts. Although certain additives seem beneficial in the short term by promoting polymer cracking and improving the selectivity of aromatics, the transport of the additives and their degradation products and increased carbon coking can contaminate products, deactivate or modify catalysts, and foul reactors. These findings address a critical knowledge gap in effectively converting waste plastics via a greener route.
42 ENGINEERING↗
Tunable structure and reinforcement of polyvinyl alcohol (PVA) hydrogels using fungal chitin particles
Polysaccharides, including chitin, are one of the most abundant biopolymers in nature and are increasingly recognized as a sustainable alternative to petroleum-derived plastics and synthetic fillers in polymer composites. Traditionally sourced from crustacean shells, chitin offers mechanical strength and biocompatibility with limitations also in processability and functionality. Fungal-derived chitin material represents a promising alternative, with advantages including scalable fermentation on low-cost substrates, absence of shellfish allergens, and tunable molecular architectures that vary by species, developmental stage, and growth environment. Here, in this study, we systematically examined chitinous materials obtained from taxonomically and functionally distinct fungi, Laccaria bicolor, Trichoderma reesei and Rhizopus oryzae, to assess their structural, chemical, and morphological properties as reinforcement agents in polymer composites. Mild alkaline pretreatment was employed to obtain mycelium chitin particles, thereby improving accessibility to chitin and co-occurring β-D-glucans while maintaining microparticle integrity. Comprehensive FTIR and solid-state NMR analyses revealed species-specific differences in chemical composition and microstructure, with R. oryzae exhibiting a unique spectral signature. These fungal-derived chitin were then incorporated into poly(vinyl alcohol) (PVA) hydrogels, where they acted as reinforcing fillers without the need for additional chemical crosslinkers. Comparative evaluation of hydrogel properties demonstrated that fungal chitin significantly enhanced mechanical performance, with all mycelium fillers mitigating the water weakening in PVA hydrogels. R. oryzae-derived composites tripled the hydrogel tensile strength while the submicron fibrous morphology in L. bicolor contributes to over 45 % tensile improvement in dry PVA composites. Our findings highlight the potential of fungal biomass as a tunable, sustainable platform for producing chitin-based reinforcing agents.
Chitin↗
Effect of Fillers and of Mixing Procedure on the Strength of Plastic Materials
Explore the source record for details and available documents.
Kynoch, William↗
Inorganic-organic separators for alkaline batteries
A flexible separator is reported for use between the electrodes of Ni-Cd and Ni-Zn batteries using alkaline electrolytes. The separator was made by coating a porous substrate with a battery separator composition. The coating material included a rubber-based resin copolymer, a plasticizer and inorganic and organic fillers which comprised 55% by volume or less of the coating as finally dried. One or more of the filler materials, whether organic or inorganic, is preferably active with the alkaline electrolyte to produce pores in the separator coating. The plasticizer was an organic material which is hydrolyzed by the alkaline electrolyte to improve conductivity of the separator coating.
Sheibley, D. W.↗
Surface Modified Fly Ash for Value Added Products (SuMo Fly Ash)
The objective of this project is to develop a technology to encapsulate coal fly ash particles in sulfurized vegetable oil, enhancing physical and mechanical properties of the fly ash as a filler material when applied in commercial products. This project significantly advances the knowledge base and technology for synthesizing coated fly ash particles for application in different polymer matrices to increase cross-linking, compatibility, air-entrainment and to decrease the leaching potential of metals of concern. Specifically, the project focuses on (a) collection, and characterization of fly ash material from coal power plants; (b) development of Sulfurized Vegetable Oil (SVO) modified (SuMo) fly ash and their detailed characterization; (c) evaluation of the mechanical properties of the SuMo fly ash incorporated plastic and rubber composites for potential replacement of CaCO 3 or carbon black as filler materials with SuMo fly ash in plastic and rubber composites; (d) leaching potential of SuMo fly ash and SuMo fly ash-incorporated plastic and rubber composites to determine the rate of release of trace metals. The major findings of this project are: i) Sulfurized Vegetable Oil coated fly ash (SuMo fly ash) was successfully prepared with a particle size of ≤ 45 micron which exhibited hydrophobicity of contact angle > 90°; ii) the coating reduces leaching of metals (e.g., B, Cr) from fly ash when exposed to water; iii) incorporation of SuMo fly ash increases thermal stability and yield strength of plastics; iv) SuMo coating helps disperse fly ash particles into cured rubbers, natural rubber; (v) SuMo fly ash-incorporated plastic/cured rubbers compounds protects against leaching of toxic elements.
20 FOSSIL-FUELED POWER PLANTS↗
Pull Test Verifies Gap Loading
Thin plastic strip pulled away from gap by force gage to measure pressure applied on gap filler. Force necessary to initiate movement of thin plastic strip is measure of gap tightness. Procedure determines interface pressures or loads where conventional load-measuring equipment cannot be used. Used to check refrigerator-door seals.
Hagen, G. R.↗
Conductive plastics
Electrically conductive plastics fabrication and applications limitations, discussing plastic matrix materials loaded with various conductive fillers
Litant, I.↗
Material property characterization of 3D printed polypropylene wood plastic composites
Abstract Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.
Hwang, Sungjun↗
Advanced inorganic separators for alkaline batteries
A flexible, porous battery separator comprising a coating applied to a porous, flexible substrate is described. The coating comprises: (1) a thermoplastic rubber-based resin which is insoluble and unreactive in the alkaline electrolyte; (2) a polar organic plasticizer which is reactive with the alkaline electrolyte to produce a reaction product which contains a hydroxyl group and/or a carboxylic acid group; and (3) a mixture of polar particulate filler materials which are unreactive with the electrolyte, the mixture comprising at least one first filler material having a surface area of greater than 25 meters sq/gram, at least one second filler material having a surface area of 10 to 25 sq meters/gram, wherein the volume of the mixture of filler materials is less than 45% of the total volume of the fillers and the binder, the filler surface area per gram of binder is about 20 to 60 sq meters/gram, and the amount of plasticizer is sufficient to coat each filler particle. A method of forming the battery separator is also described.
Sheibley, D. W.↗