Search NASA⌕ Search

SEARCH · Search NASA

Results for “SILICON JUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Fundamental limitations imposed by high doping on the performance of pn junction silicon solar cells

Fundamental limitations imposed on the performance of silicon junction solar cells by physical mechanisms accompanying high doping are described. The one-dimensional mechanisms divide into two broad categories: those associated with band-gap shrinkage and those associated with interband transition rates. By extending the traditional method of analysis and comparing with measurement, it is shown that the latter kind of mechanism dominates in determining the open-circuit voltage in a one-dimensional model of a 0.1 ohm-cm cell at 300 K. As an alternative dominant mechanism, a three-dimensional model involving thermodynamically stable clusters of impurities in the highly-doped diffused layer is suggested.

Lindholm, F. A.↗
NASA NTRS1977

Developments in vertical-junction silicon solar cells

Non-reflective vertical junction silicon cells provide high conversion efficiency radiation-resistant solar cells. New techniques of oxidation growth and the use of photolithography enable the use of an orientation dependent etch producing grooves 5 to 10 microns wide over 100 microns deep. These silicon wafers are then processed into solar cells with all of the processes performed at temperatures compatible with producing high efficiency solar cells. Most of the photogenerated carriers are created in the walls where they are within a few microns of the collecting junction. Consequently, degradation of carrier diffusion length due to radiation has a considerably reduced effect on collection efficiency. These 2 cm x 2 cm vertical junction silicon solar cells have exceeded 13% AMO efficiency and have shown superior radiation resistance.

Lindmayer, J.↗
NASA NTRS1987

Excimer laser annealing: A gold process for CZ silicon junction formation

A cold process using an excimer laser for junction formation in silicon has been evaluated as a way to avoid problems associated with thermal diffusion. Conventional thermal diffusion can cause bulk precipitation of SiOx and SiC or fail to completely activate the dopant, leaving a degenerate layer at the surface. Experiments were conducted to determine the feasibility of fabricating high quality p-n junctions using a pulsed excimer laser for junction formation at remelt temperature with ion-implanted surfaces. Solar-cell efficiency exceeding 16 percent was obtained using Czochralski single-crystal silicon without benefit of back surface field or surface passivation. Characterization shows that the formation of uniform, shallow junctions (approximately 0.25 micron) by excimer laser scanning preserves the minority carrier lifetime that leads to high current collection. However, the process is sensitive to initial surface conditions and handling parameters that drive the cost up.

Wong, David C.↗
NASA NTRS1977

Measurement of material parameters that limit the open-circuit voltage in P-N-junction silicon solar cells

The greatest gains in solar energy conversion efficiency of p-n-junction silicon solar cells come from increasing the open-circuit voltage V sub OC; it is important to understand and characterize the material parameters that limit the V sub OC. Strong experimental evidence exists to support the assertion that either an anomalously large minority carrier charge storage or an anomalously small minority carrier lifetime in the quasi-neutral emitter region limits the open circuit voltage. A method is presented for measuring charge storage and effective lifetime. Static and transient measurements are analyzed using physical models of the solar cell characteristics. This analysis yields the emitter charge storage and life-time, which then can be related to the various physical mechanisms, such as energy band gap shrinkage, that have been proposed earlier as responsible for limiting V sub OC.

Lindholm, F. A.↗
DOE OSTI2020

Electroluminescence Characterization of Recombination in Back Junction Silicon Heterojunction Test Structures: Role of the Inversion Layer

Electroluminescence (EL) characterization technique is used to quantify recombination properties in back junction silicon (Si) heterojunction (HJ) solar cell test structures with interdigitated back contact (IBC) emitters and metal contacts. These test structures are three terminal devices that allow the selective biasing and injection of minority carriers into spatially isolated emitter strips having different widths. This allows the study of minority carriers' current transport, flow, and recombination in these regions, which can, then, be applied to full IBC cells. EL is used to verify that emission is proportional to the minority carriers' concentration in the corresponding regions of the device, thus providing information relevant to minority carriers' collection when compared with laser beam induced current technique in considerably less time and with a higher spatial resolution. Current transport through the inversion layer that occurs due to the band bending at the n crystalline Si and p amorphous Si interface is discussed relying on the distance that minority carriers travel in different configurations and on their diffusion length. Laser defect spots (LDS) were, then, introduced in the emitter regions to analyze the spatial profile of minority carriers as they recombine at the LDS due to their high surface recombination velocity. Ideality factors in different configurations are spatially mapped from EL before and after introducing LDS and are used to show the effect of the inversion layer on the different recombination mechanisms. Current transport through the inversion layer is studied at different biasing conditions and correlated with current transport after LDS.

42 ENGINEERING↗
NASA NTRS1979

The importance of surface recombination and energy-bandgap narrowing in p-n-junction silicon solar cells

Experimental data demonstrating the sensitivity of open-circuit voltage to front-surface conditions are presented for a variety of p-n-junction silicon solar cells. Analytical models accounting for the data are defined and supported by additional experiments. The models and the data imply that a) surface recombination significantly limits the open-circuit voltage (and the short-circuit current) of typical silicon cells, and b) energy-bandgap narrowing is important in the manifestation of these limitations. The models suggest modifications in both the structural design and the fabrication processing of the cells that would result in substantial improvements in cell performance. The benefits of one such modification - the addition of a thin thermal silicon-dioxide layer on the front surface - are indicated experimentally.

Fossum, J. G.↗
NASA NTRS1986

Improved High/Low Junction Silicon Solar Cell

Method developed to raise value of open-circuit voltage in silicon solar cells by incorporating high/low junction in cell emitter. Power-conversion efficiency of low-resistivity silicon solar cell considerably less than maximum theoretical value mainly because open-circuit voltage is smaller than simple p/n junction theory predicts. With this method, air-mass-zero opencircuit voltage increased from 600 mV level to approximately 650 mV.

Neugroschel, A.↗
NASA NTRS1985

Fabrication and analysis of dot junction silicon solar cells

A design of solar cells with reduced junction area on the cell surface is investigated for reduction of saturation current and increase in open-circuit voltage. Equidiameter dot junctions distributed across the surface of the cell offer an efficient alternative, with variations in dot diameter and in the spacing between dots giving the required variations in the ratio of junctions area to total surface area. A simplified analysis for short-circuit current and other cell parameters, which enables cell design optimization, is presented. Efficiencies beyond 18 percent are obtainable in flat-plate terrestrial applications. Experimental solar-cell performance results, as functions of different area ratios, and bulk doping are presented. It is shown that saturation current reduction and open-circuit voltage increase is obtained by reduced junction area.

Crotty, G. T.↗
NASA NTRS1982

Photovoltaic investigation of minority carrier lifetime in the heavily-doped emitter layer of silicon junction solar cell

The results of experiments on the recombination lifetime in a phosphorus diffused N(+) layer of a silicon solar cell are reported. The cells studied comprised three groups of Czochralski grown crystals: boron doped to one ohm-cm, boron doped to 6 ohm-cm, and aluminum doped to one ohm-cm, all with a shunt resistance exceeding 500 kilo-ohms. The characteristic bulk diffusion length of a cell sample was determined from the short circuit current response to light at a wavelength of one micron. The recombination rates were obtained by measurement of the open circuit voltage as a function of the photogeneration rate. The recombination rate was found to be dependent on the photoinjection level, and is positive-field controlled at low photoinjection, positive-field influence Auger recombination at a medium photoinjection level, and negative-field controlled Auger recombination at a high photoinjection level.

Ho, C.-T.↗
NASA NTRS1981

Development of thin wraparound junction silicon solar cells

The state of the art technologies was applied to fabricate 50 micro thick 2x4 cm, coplanar back contact (CBC) solar cells with AMO efficiency above 12%. A requirement was that the cells have low solar absorptance. A wraparound junction (WAJ) with wraparound metallization was chosen. This WAJ approach avoided the need for very complex fixturing, especially during rotation of the cells for providing adequate contacts over dielectric edge layers. The contact adhesion to silicon was considered better than to an insulator. It is indicated that shunt resistance caused by poor WAJ diode quality, and series resistance from the WAJ contact, give good cell performance. The cells developed reached 14 percent AMO efficiency (at 25 C), with solar absorptance values of 0.73. Space/cell environmental tests were performed on these cells and the thin CSC cells performed well. The optimized design configuration and process sequence were used to make 50 deliverable CBC cells. These cells were all above 12 percent efficiency and had an average efficiency of -13 percent. Results of environmental tests (humidity-temperature, thermal shock, and contact adherence) are also given.

Ho, F.↗
NASA NTRS1986

Improved High/Low Junction Silicon Solar Cell

Air-mass-zero open-circuit voltage increased to 650 mV. Oxide-chargeinduced high/low emitter solar cell, electron accumulation layer induced by positive charge. High/low emitter suppresses dark emitter recombination current, resulting in power-conversion efficiencies significantly higher than previously achieved.

Neugroschel, A.↗
NASA NTRS2020

U309 N-Channel Silicon Junction Field Effect Transistor Total Ionizing Dose Characterization Report

The purpose of this testing was to characterize the InterFET Corporation U309 for total dose response. This test shall serve as the radiation lot acceptance test (RLAT) for the lot date code (LDC) tested. The U309 is a discrete Junction Field Effect Transistor (JFET). High dose rate (HDR) irradiations were performed in this test so that the device susceptibility to Total Ionizing Dose (TID) could be determined.

Total Ionizing Dose (TID)↗
NASA NTRS1972

Effects of 22 MeV protons on single junction and silicon controlled rectifiers

The effects of 22-MeV protons on various types of silicon single junction and silicon controlled rectifiers were investigated. The results show that low-leakage devices and silicon controlled rectifiers are the most susceptable to radiation damage. There are also differences noted between single junction rectifiers of the same type made by different manufacturers, which emphasizes the need for better selection of devices used in spacecraft.

Beatty, M. E., III↗
NASA NTRS1975

Studies of silicon PN junction solar cells

Silicon pn junction solar cells made with low-resistivity substrates show poorer performance than traditional theory predicts. The purpose of this research was to identify and characterize the physical mechanisms responsible for the discrepancy. Attention was concentrated on the open circuit voltage in shallow junction cells of 0.1 ohm-cm substrate resistivity. A number of possible mechanisms that can occur in silicon devices were considered. Two mechanisms which are likely to be of main importance in explaining the observed low values of open-circuit voltage were found: (1) recombination losses associated with defects introduced during junction formation, and (2) inhomogeneity of defects and impurities across the area of the cell. To explore these theoretical anticipations, various diode test structures were designed and fabricated and measurement configurations for characterizing the defect properties and the areal inhomogeneity were constructed.

Lindholm, F. A.↗