Multiscale stress-strain characterization of outer onion epidermal peel tissue in wet and dry states
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Residual strain in electrodeposited Li films may affect safety and performance in Li metal battery anodes, so it is important to understand how to detect residual strain in electrodeposited Li and the conditions under which it arises. To explore this Li films, electrodeposited onto Cu metal substrates, were prepared under an applied pressure of either 10 or 1000 kPa and subsequently tested for the presence or absence of residual strain via sin 2 (ψ) analysis. X-ray diffraction (XRD) analysis of Li films required preparation and examination within an inert environment; hence, a Be-dome sample holder was employed during XRD characterization. Results show that the Li film grown under 1000 kPa displayed a detectable presence of in-plane compressive strain (–0.066%), whereas the Li film grown under 10 kPa displayed no detectable in-plane strain. Here, the underlying Cu substrate revealed an in-plane residual strain near zero. Texture analysis via pole figure determination was also performed for both Li and Cu and revealed a mild fiber texture for Li metal and a strong bi-axial texture of the Cu substrate. Experimental details concerning sample preparation, alignment, and analysis of the particularly air-sensitive Li films have also been detailed. This work shows that Li metal exhibits residual strain when electrodeposited under compressive stress and that XRD can be used to quantify that strain.
The identification of leaks in the vicinity of reservoirs is critical to determining the feasibility of long-term geologic storage of CO2, methane, wastewater and other fluids. We have established a series of basic reservoir leakage scenarios and performed numerical analysis to characterize the associated pressure and strain fields created from injection into these leaky reservoir settings, as well from ambient loads, such as barometric pressure and earth tides. The end-member conceptual models evaluated include injection and ambient loads applied to: 1) a thin, horizontal layer with no leakage pathways (baseline), 2) a thin layer with a vertical conduit to the surface (e.g., a leaky fault or abandoned well) and 3) a thin layer with a conduit to an overlying aquifer. The pressure and strain fields are sensitive to the reservoir and confining unit geometry, material properties, the distribution, composition and compressibility of the pore fluid and the type of applied load (e.g., constant vs. cyclical injection, barometric pressure fluctuations, earth tides, etc.). Initial results from the numerical analyses indicate that an induced pressure change of 1 MPa in a formation at 1 km depth with a Young’s modulus of 10 GPa is sufficient to create vertical and horizontal strain signals as high as 2 με at a depth of 100 m. The signals predicted from leaky conditions compared to an intact reservoir differ by as much as 0.2 με in magnitude and evolve at different rates. We have developed instruments capable of measuring vertical and horizontal strain at a resolution of better than 5 nε and have recorded repeatable strain signals at 30 m depth in response to wastewater injection into the Avant field in Oklahoma. Based on these findings, strain signals predicted in the shallow subsurface (< 100 m) with numerical analysis are expected to be measurable, and this signal may be inverted to characterize the location and magnitude of leaks, as well as to characterize the geometry and hydromechanical properties of the formation and overlying confining units. This suggests that shallow strain measurements could be a cost effective method for characterizing and monitoring gas storage projects.
This study undertook strain analysis on fin-shaped field effect transistor structures with epitaxial Si{sub 1−x}Ge{sub x} stressors, using nano-beam electron diffraction and finite elements method. Combining the two methods disclosed dynamic strain distribution in the source/drain and channel region of the fin structure, and the effects of dimensional factors such as the stressor thickness and fin width, offering valuable information for device design.
Screening microalgae strains under static light and temperature flask conditions cannot directly quantify the biomass productivities of algae growing in the dynamically fluctuating light and temperature conditions of outdoor ponds. In this effort, we describe a testing pipeline that screens for productivity under climate simulated conditions. A validated, miniaturized Laboratory Environmental Algae Pond Simulator (mini-LEAPS) photobioreactor was used to determine optimal medium salinities and biomass productivities of cold-tolerant microalgae collected from Arctic, subarctic, Antarctic, and subalpine habitats. Strains characterized in this effort include: Chlorella antarctica UTEX1959, Chlorella sp. UTEXSNO69, Chloromonas rosae UTEXSNO11, Phaeodactylum tricornutum UTEX646, and Stichococcus minutus CCALA727. Observed productivities of the characterized strains ranged from 1.74 ± 0.25 to 8.18 ± 0.81 g m –2 day –1 (as ash-free dry weight). For each strain, a temperature tolerance profile was generated to identify the most appropriate season (s) for cultivation. The two most promising strains, Chlorella sp. UTEX SNO69 and P. tricornutum UTEX646, were tested alongside the DISCOVR winter benchmark strain Monoraphidium minutum 26B-AM in outdoor open ponds at the PNNL Algae Testbed (PAT) in Arizona. Further, under cold-season outdoor pond conditions, Chlorella sp. UTEXSNO69 achieved average areal biomass productivities of 8.21 ± 0.50 g m –2 day –1 , not significantly different from that of the benchmark strain (8.52 ± 0.43 g m –2 day –1 , p > 0.05). Under spring outdoor pond conditions, P. tricornutum UTEX646 achieved average areal biomass productivities 10.34 ± 0.27 g m –2 day –1 , not significantly different from that of the benchmark (10.07 ± 0.50 g m –2 day –1 ) under the tested conditions (p > 0.05). The streamlined pipeline was thus demonstrated to successfully characterize productive microalgae strains for outdoor deployment by weeding out algae strains that were not productive under the tested dynamic light and temperature conditions.
Not Available
Explore the source record for details and available documents.
Abstract not provided.
We induced periodic biaxial tensile strain in polycrystalline graphene by wrapping it over a substrate with repeating pillar-like structures with a periodicity of 600 nm. Using Raman spectroscopy, we determined to have introduced biaxial strains in graphene in the range of 0.4% to 0.7%. Its band structure was characterized using photoemission from valance bands, shifts in the secondary electron emission, and x-ray absorption from the carbon 1s levels to the unoccupied graphene conduction bands. It was observed that relative to unstrained graphene, strained graphene had a higher work function and higher density of states in the valence and conduction bands. Furthermore, we measured the conductivity of the strained and unstrained graphene in response to a gate voltage and correlated the changes in their behavior to the changes in the electronic structure. From these sets of data, we propose a simple band diagram representing graphene with periodic biaxial strain.
Photoreflectance (PR), using a uv (374 nm) diode laser probe beam, and Raman spectroscopy, using a multi-wavelength Ar{sup +} laser coupled to a high-resolution multi-wavelength spectrometer, were used to characterize the strain relaxation of Si top layers grown on a graded and relaxed SiGe buffer stack with a final Ge concentration of 20%. The Si top layer thicknesses ranged from 1.6 to 18 nm. Considerable radial variation in the strain relaxation was seen in all sampled wafers, highlighting the need for rapid, local strain characterization. Strong correlation between shift in the Si layer dielectric response, measured by uv-PR, and the Si top layer strain, measured by Raman, is reported.
Abstract This paper introduces an experimental procedure aiming at performing a consistent mechanical characterization of textile composites behavior, under static and dynamic loadings, and particularly their macroscopic strain rate‐dependent mechanisms. The procedure includes the design and validation of a reduced specimen adapted to dynamic testing, which guarantees the consistency of the identified macroscopic properties under a wide range of strain rates. An interrupted high speed tensile apparatus was also developed to investigate the strain rate sensitivity of the nonlinear constitutive behavior from = 10 − 4 s − 1 to 10 2 s − 1 . The originality of this experimental device lies in its ability to stop high speed loadings before ultimate failure, at adjustable, accurate strain levels. Finally, an extensive characterization campaign was performed. Results reveal a high strain rate dependency of the linear and nonlinear behavior. The procedure therefore generates consistent characterization data that may trustworthily be used for modeling purposes.
For an investigation of problems of composites at high strain rates with dominant wave propagation effects, such as dynamically loaded composite jet engine blades, the longitudinal, transverse, and in-plane shear properties of unidirectional SP 288/AS graphite/epoxy were measured at various strain rates ranging from quasi-static to over 500/s. The test specimens were rings 10.16 cm in diameter, 2.54 cm long, 6 to 8 plies thick, and with fibers at 0, 90, and 10 deg off-axis. Quasi-static testing was conducted in a fixture which applies hydraulic pressure to the ring specimens, and dynamic testing was conducted by applying an internal pressure pulse through a liquid in a special fixture. Dynamic stress-strain curves are presented. For the 0-deg specimens, the modulus increases with strain up to 20 percent of the static value. The modulus and strength increase sharply in the 90-deg rings with strain rate reaching values two to three times the corresponding static rate.
Friction stir welding (FSW) is a solid state welding process with potential advantages for aerospace and automotive industries dealing with light alloys. Self-reacting friction stir welding (SR-FSW) is one variation of the FSW process being developed at the National Aeronautics and Space Administration (NASA) for use in the fabrication of propellant tanks. Friction plug welding is used to seal the exit hole that remains in a circumferential SR-FSW. This work reports on material properties and strain patterns developed in a SR-FSW with a friction plug weld. Specifically, this study examines the behavior of a SR-FSW formed between an AA 2014-T6 plate on the advancing side and an AA 2219-T87 plate on the retreating side and a SR-FSW (AA 2014-T6 to AA 2219-T87) with a 2219-T87 plug weld. This study presents the results of a characterization of the micro-hardness, joint strength, and strain field characterization of SR-FSW and FPW joints tested at room temperature and cryogenic temperatures.
The sensitivity and the precision of the Geometric Phase Analysis (GPA) method for strain characterization is a topic widely discussed in the literature and is usually difficult to quantify. Indeed, the GPA precision is intricately linked to the resolution of the strain maps defined when masking the periodic reflections in Fourier space. In this study an additional parameter, sampling, is proposed to be analyzed regarding the precision of GPA by developing the concept of a phase noise in the GPA equations. Both experimentally and theoretically, the following article demonstrates how the precision, and the sensitivity of the GPA method is improved when using a larger pixel spacing to record an electron micrograph in Scanning Transmission Electron Microscopy (STEM). In conclusion, the counterintuitive concept of increasing the field of view to improve the GPA precision results in an extension of the application of strain characterization methods in STEM towards low deformation levels.
Introduction Outbreak investigation of foodborne salmonellosis is hindered when the food source is contaminated by multiple strains of Salmonella , creating difficulties matching an incriminated organism recovered from patients with the specific strain in the suspect food. An outbreak of the rare Salmonella Adjame was caused by multiple strains of the organism as revealed by single-nucleotide polymorphism (SNP) variation. The use of highly discriminatory prophage analysis to characterize strains of Salmonella should enable a more precise strain characterization and aid the investigation of foodborne salmonellosis. Methods We have carried out genomic analysis of S. Adjame strains recovered during the course of a recent outbreak and compared them with other strains of the organism ( n = 38 strains), using SNPs to evaluate strain differences present in the core genome, and prophage sequence typing (PST) to evaluate the accessory genome. Phylogenetic analyses were performed using both total prophage content and conserved prophages. Results The PST analysis of the S. Adjame isolates showed a high degree of strain heterogeneity. We observed small clusters made up of 2-6 isolates ( n = 27) and singletons ( n = 11) in stark contrast with the three clusters observed by SNP analysis. In total, we detected 24 prophages of which only four were highly prevalent, namely: Entero_p88 (36/38 strains), Salmon_SEN34 (35/38 strains), Burkho_phiE255 (33/38 strains) and Edward_GF (28/38 strains). Despite the marked strain diversity seen with prophage analysis, the distribution of the four most common prophages matched the clustering observed using core genome. Discussion Mutations in the core and accessory genomes of S. Adjame have shed light on the evolutionary relationships among the Adjame strains and demonstrated a convergence of the variations observed in both fractions of the genome. We conclude that core and accessory genomes analyses should be adopted in foodborne bacteria outbreak investigations to provide a more accurate strain description and facilitate reliable matching of isolates from patients and incriminated food sources. The outcomes should translate to a better understanding of the microbial population structure and an 46 improved source attribution in foodborne illnesses.
Methanothermus fervidus Stetter 1982 is the type strain of the genus Methanothermus. This hyperthermophilic genus is of a thought to be endemic in Icelandic hot springs. M. fervidus was not only the first characterized organism with a maximal growth temperature (97°C) close to the boiling point of water, but also the first archaeon in which a detailed functional analysis of its histone protein was reported and the first one in which the function of 2,3-cyclodiphosphoglycerate in thermoadaptation was characterized. Strain V24S T is of interest because of its very low substrate ranges, it grows only on H2 + CO2. This is the first completed genome sequence of the family Methanothermaceae . Here we describe the features of this organism, together with the complete genome sequence and annotation. The 1,243,342 bp long genome with its 1,311 protein-coding and 50 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.