Search NASA⌕ Search

SEARCH · Search NASA

Results for “Warpage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A theory for predicting composite laminate warpage resulting from fabrication

Linear laminate theory is used with the moment-curvature relationship to derive equations for predicting end deflections due to warpage without solving the coupled fourth-order partial differential equations of the plate. Composite micro- and macrohyphenmechanics are used with laminate theory to assess the contribution of factors such as ply misorientation, fiber migration, and fiber and/or void volume ratio nonuniformity on the laminate warpage. Using these equations, it was found that a 1 deg error in the orientation angle of one ply was sufficient to produce warpage end deflection equal to two laminate thicknesses in a 10 inch by 10 inch laminate made from 8 ply Mod-I/epoxy. Using a sensitivity analysis on the governing parameters, it was found that a 3 deg fiber migration or a void volume ratio of three percent in some plies is sufficient to produce laminate warpage corner deflection equal to several laminate thicknesses. Tabular and graphical data are presented which can be used to identify possible errors contributing to laminate warpage and/or to obtain an a priori assessment when unavoidable errors during fabrication are anticipated.

Chamis, C. C.↗
NASA NTRS1975

A theory for predicting composite laminate warpage resulting from fabrication

Linear laminate theory is used in conjunction with the moment-curvature relationship to derive equations for predicting end deflections due to warpage without solving the coupled fourth-order partial differential equations of the plate. Using these equations, it is found that a 1 deg error in the orientation angle of one ply is sufficient to produce warpage end deflection equal to two laminate thicknesses in a 10 inch by 10 inch laminate made from 8-ply Mod-I/epoxy. From a sensitivity analysis on the governing parameters, it is found that a 3 deg fiber migration or a void volume ratio of three percent in some plies is sufficient to produce laminate warpage corner deflection equal to several laminate thicknesses. Tabular and graphical data are presented which can be used to identify possible errors contributing to laminate warpage and/or to obtain an a priori assessment when unavoidable errors during fabrication are anticipated.

Chamis, C. C.↗
NASA NTRS2002

Warpage of Large Curved Composite Panels due to Manufacturing Anomalies

This paper discusses the influences of a misaligned layer, a resin-rich slightly thicker layer, and a small thermal gradient on the thermally-induced deformations of large curved composite panels during cooldown from their cure temperature. The deformations represent warpage of the panels due to anomalies that occur during layup, consolidation, and cure. Two-dimensional finite element analyses are used The deformations are categorized as to their impact on circumferential and twist warpage metrics. The results are intended to highlight the sensitivity of manufactured panel shape to the various unwanted effects that can occur during manufacturing.

Starnes, James H., Jr.↗
NASA NTRS1977

Composite laminate warpage

Set of simplified equations predicts warpage that often occurs upon removal from fabrication mold. Equations predict corner deflection and are based upon micromechanics and macromechanics of composites, as well as laminate theory. Factors considered include ply misorientation, fiber migration, and void/volume ratio nonuniformity.

Chamis, C. C.↗
NASA NTRS1982

A proposed configuration for a stepped specimen to be used in the systematic evaluation of factors influencing warpage in metallic alloys being used for cryogenic wind tunnel models

A proposed configuration for a stepped specimen to be used in the system evaluation of mechanisms that can introduce warpage or dimensional changes in metallic alloys used for cryogenic wind tunnel models is described. Considerations for selecting a standard specimen are presented along with results obtained from an investigation carried out for VASCOMAX 200 maraging steel. Details of the machining and measurement techniques utilized in the investigation are presented. Initial results from the sample of VASCOMAX 200 show that the configuration and measuring techniques are capable of giving quantitative results.

Wigley, D. A.↗
NASA NTRS1969

Techniques for controlling warpage and residual stresses in welded structures

Thermal pattern alteration technique controls both distortion and residual stresses in aluminum weldments. Cryogenic liquids and auxiliary heat sources are used to produce contraction and expansion of metal in the vicinity of the weld in such a manner as to counterbalance expansion and contraction caused by welding.

Cole, D. Q.↗
NASA NTRS1983

Dimensional stability considerations for cryogenic metals

Work performed as part of an effort to identify, and where possible separate out, some of the factors that contribute to dimensional stability in cryogenic wind tunnel models is reported. Initial problems were encountered with two dimensional models made of 15-5 PH stainless steel, which warped significantly after being subjected to cryogenic testing in the 0.3 Meter Transonic Cryogenic Tunnel. Subsequently, an effort was undertaken to investigate the mechanisms that could cause model warpage during cryogenic testing. The two basic mechanisms that can lead to warpage are (1) metallurgical structural instability in which one phase transforms partially or fully into a second phase which has a different crystal structure and volume, and (2) deformation due to the creation, or relief, of unbalanced induced or residual stresses. In the case of the 15-5 PH airfoils, it is highly probable that metallurgical instability was responsible for most of the observed warpage. A particular specimen configuration was established for use in the systematic evaluation of the factors influencing warpage. Preliminary studies of a specimen made of VASCOMAX 200 suggest the possibility of manipulating the stresses in the surface layers by appropriate combinations of milling and grinding steps. This opens up the possibility of correcting or establishing the required surface profile of an airfoil.

Wigley, D. A.↗
NASA NTRS2006

Development of Laser Fabricated Ti-6Al-4V

Laser Engineered Net Shaping (LENS) depositions with Ti-6Al-4V gas-atomized powder were accomplished at five different temperatures, ranging from 30 to 400 C, imposed on the base plate. These base plate temperatures were employed in an effort to relieve stresses which develop during the deposition. Warpage of the base plate was monitored. Only a slight decline in warpage was observed as the base plate temperature was increased. Results indicate that substrate temperatures closer to the stress relief minimum of 480 C would relieve deposition stresses, though process parameters would likely need to be modified to compensate for the higher base plate temperature. The compositions of the as-received powder and the LENS deposited material were chemically analyzed. The oxygen content of the LENS material was 0.154 wt.% which is less than the maximum impurity limit of 0.2 percent for commercial Ti-6Al-4V alloys, but is over the limit allowed in ELI grade (0.13 percent). The level of oxygen in the commercial base plate used was only 0.0635 percent. Tensile specimens were machined from the LENS deposited material and tested in tension at room temperature. The ultimate and yield tensile stresses of the LENS material were about 1200 and 1150 MPa respectively, which is about 20 percent higher than the strengths of wrought Ti-6Al-4V. The higher strength of the LENS material was due to its fine structure and high oxygen content. The LENS deposits were not fully dense; voids were frequent at the interfaces between deposited layers. These dispersed sheets of voids were parallel to the longitudinal axis of the resulting tensile specimens. Apparently there was sufficient continuous, fully dense material longitudinally to enable the high strengths. Ductility was low in the LENS material. Percent elongation at failure in the LENS material was near 4 percent, which is less than half of what is usually expected from Ti-6Al-4V. The low ductility was caused by high oxygen levels, and the presence of voids. It is likely that the relatively high scan speeds used in our depositions contributed to the lack of full density in our LENS material.

deGroh, Henry C., III↗
NASA NTRS1966

Plug replaces weld filler as seal in complex casting

Expandable metal plug is inserted to provide a seal to support the mold core with small blocks, referred to as chaplets, during the casting of a complex volute. Weld-warpage and multiple X ray inspection are eliminated by use of this technique.

Goundrey, R. L.↗
NASA NTRS1967

Stabilizing stainless steel components for cryogenic service

Warpage and creep in stainless steel valve components are decreased by a procedure in which components are machined to a semifinish and then cold soaked in a bath of cryogenic liquid. After the treatment they are returned to ambient temperature and machine finished to the final drawing dimensions.

Holden, C. F.↗
NASA NTRS1967

Precision metal molding

Method provides precise alignment for metal-forming dies while permitting minimal thermal expansion without die warpage or cavity space restriction. The interfacing dowel bars and die side facings are arranged so the dies are restrained in one orthogonal angle and permitted to thermally expand in the opposite orthogonal angle.

Townhill, A.↗
NASA NTRS1968

Asbestos and Inconel combined to form hot-gas seal

Hot-gas seal prevents warpage tendencies in large flange joints exposed to high temperatures, such as those present in large space vehicle engine exhausts. Two Inconel wire mesh cores are held in place by an asbestos cloth cover that acts as a spacer to form the seal.

Wooster, C. W., Jr.↗
NASA NTRS1973

Performance of a 15 cm ion thruster with dished grids

Increases in grid perveance through reductions in grid spacings without the attendant tendency toward arcing and shorting between grids at close spacing are shown to be achievable through substitution of higher-perveance dished grids for flat grids. Such dished grids can be spaced more closely than flat grids without exhibiting a propensity for shorting because their thermal warpage characteristics are more uniform and predictable.

Wilbur, P. J.↗