Search NASA⌕ Search

SEARCH · Search NASA

Results for “dielectric solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effective Dielectric Passivation Scheme in Area-Selective Front/Back Poly-Si/SiOx Passivating Contact Solar Cells

Explored different dielectric passivation schemes on lifetime samples after removing poly-Si completely. Showed that SiNx/Al2O3 had the best passivation properties on SiOx/n+ c-Si in diffused surface. Applied SiNx/Al2O3 stack on poly-Si/SiOx passivating contact device and showed large improvement in Jsc, with best device efficiency of 21.8%. Future work: CV measurement of dielectric stacks to obtain Qf and Dit.

dielectric↗
DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV Voc Si Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the loss analysis of silicon solar cells with polysilicon on locally-etched dielectric passivating contacts with Voc=729.0 mV and efficiency=22.6% has been presented. Experimentally, nano-pinholes were introduced in SiO x (2.2 nm) and SiO x /SiN y (2.2 nm/8nm) stack using metal-assisted chemical etching (MACE). SunSolve and Quokka3 were used to simulate the experimental solar cell and investigate the optical and electrical power losses. Simulations suggest maximum power loss occurs due to recombination and resistive losses in the bulk (~0.76 mW/cm2) followed by power loss due to rear contact recombination (~0.35 mW/cm2). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and hence, efficiency has been investigated. Further, advanced structures have been proposed to minimize recombination and parasitic absorption to achieve higher Voc and Jsc of the solar cells with locally-etched dielectric passivating contacts.

contacts↗
DOE OSTI2022

Room Temperature, Dip Coating Organic Passivation for c-Si Surfaces

Surface passivation of crystalline Si (c-Si) to reduce recombination rate is crucial to obtain high-efficiency c-Si solar cells. A fast passivation technique that can be performed at room temperature is needed when studying the degradation behaviors using various characterization methods to not destroy the degraded states. In this contribution, we explore Nafion via dip coating on n-type Cz wafers. We show that both the Nafion concentration and the conditions of surface and edge affect the passivation quality, and we achieve excellent passivation quality of iVoc of 716 mV, with a saturation current density (J0) of 7 fA/cm2. Additionally, electron paramagnetic resonance (EPR) shows Nafion can be used under cryogenic temperature and reveals the reduction of Si dangling bond after Nafion treatment.

dielectric solar cell↗
DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV VocSi Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the performance analysis of a 22.5% efficient polysilicon on silicon oxide (poly-Si/SiOx) passivated contact solar cells with deliberately introduced pinholes using metal-assisted chemical etching (MACE) has been performed with the help of optical analysis using Sunsolve and electrical analysis using Quokka3. The power loss is maximum due to recombination and resistive losses in the bulk (~0.76 mW/cm2 ) followed by power loss due to rear contact recombination (~0.35 mW/cm2 ). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and efficiency has been investigated.

MACE↗
DOE OSTI2020

On the hydrogenation of Poly-Si passivating contacts by Al 2 O 3 and SiN x thin films

Doped polycrystalline silicon (poly-Si), when coupled with a thin SiO 2 interlayer, is of large interest for crystalline silicon ( c -Si) solar cells due to its outstanding passivating contact properties. To reach high levels of surface passivation, it is pivotal to hydrogenate the poly-Si and the underlying c -Si/SiO 2 interface. This can be done by capping the poly-Si with a hydrogen-containing dielectric layer such as Al 2 O 3 or SiN x , followed by a thermal anneal. On the basis of recent research, this work addresses several aspects of such hydrogenation by dielectric materials, including the effect of the annealing ambient, the thermal stability and reversibility of hydrogenation, the poly-Si doping level and c -Si surface texture. Additionally, the implementation of hydrogenation of poly-Si by dielectric materials in solar cells is discussed.

14 SOLAR ENERGY↗
DOE OSTI2021

Effective Dielectric Passivation Scheme in Area-Selective Front/Back Poly-Si/SiOx Passivating Contact Solar Cells

Despite the high efficiencies reached by heavily doped poly-Si/SiO x passivating contact solar cells, challenges like the high front parasitic absorption still limit their performance. Previously, we showed a wet etching technique using self-aligned metal grids to remove the front poly-Si in the non-metallized region. Here, we focus on the effective dielectric passivation on this tunneling oxide/n + in-diffused region. The effect of poly-Si thickness was studied to balance between the passivation quality and the current gain. We then compared various dielectric passivation schemes using SiN x , Al 2 O 3 , and stacks thereof via injection-level dependent lifetime and the transfer length method. We demonstrate a SiN x /Al 2 O 3 stack yielded the best passivation performance within device process limitation and obtained an improved front/back poly-Si/SiO x passivating contact device, with a short circuit current density of 41.8 mA/cm 2 and an efficiency of 21.8%.

anisotropic wet etching↗
DOE OSTI2025

Dielectric constant engineering of nonfullerene acceptors enables a record fill factor of 83.58% and a high efficiency of 20.80% in organic solar cells

Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) surpassing 20%, but their development remains hindered by the inherently low dielectric constant (εr) of organic semiconductors, which limits charge transport and contributes to serious recombination losses. Herein, we present a comprehensive strategy to overcome the challenge by engineering the dielectric properties of nonfullerene acceptors (NFAs). Two Y-series NFAs of BTP-N3F and BTP-C3F have been synthesized featuring trifluoromethyl (CF 3 ) end-capped alkyl side chains. This molecular design significantly enhances the dipole moment and ε r (up to ∼5.9) when compared to the reference acceptor Y6 (∼3), reducing the exciton binding energy (E b ) and improving charge transport. Furthermore, the incorporation of a high-εr polymer additive, poly(pentafluorostyrene) (PPFS), synergistically improves the active layer morphology and dielectric properties, enabling efficient charge extraction and reduced recombination losses. Devices based on the optimized D18-Cl/BTP-C3F system have achieved a record-high fill factor (FF) of 83.58% and an impressive PCE of 20.80%, setting a new benchmark for OSCs. Finally, our results underscore the pivotal role of ε r in enhancing device performance and establish a versatile pathway for advancing OSC efficiency and stability through molecular and morphological optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of Charge Transport Layers on Capacitance Measured in Halide Perovskite Solar Cells

Capacitance-based techniques were previously used to measure the electrical properties of halide perovskite solar cells (PSCs) such as defect activation energy and density, carrier concentration, and dielectric constant, which provide key information for evaluating the device performance. Herein, we show that capacitance-based techniques cannot be used to reliably analyze the properties of defects in the perovskite layer or at its interface, since the high-frequency capacitance signature is due to the response of charge carriers in the hole-transport layer (HTL). For HTL-free PSCs, the high-frequency capacitance can be considered as the geometric capacitance for analyzing the dielectric constant of the perovskite layer, since there is no trapping and de-trapping of charge carriers in the perovskite layer. We also find that the low-frequency capacitance signature can be used to calculate the activation energy of the ionic conductivity of the perovskite layer, but the overlapping effects with charge transport materials must be avoided.

14 SOLAR ENERGY↗
DOE OSTI2020

3,4‐Dicyanothiophene—a Versatile Building Block for Efficient Nonfullerene Polymer Solar Cells

Abstract In this contribution, a versatile building block, 3,4‐dicyanothiophene (DCT), which possesses structural simplicity and synthetic accessibility for constructing high‐performance, low‐cost, wide‐bandgap conjugated polymers for use as donors in polymer solar cells (PSCs), is reported. A prototype polymer, PB3TCN‐C66, and its cyano‐free analogue polymer PB3T‐C66, are synthesized to evaluate the potential of using DCT in nonfullerene PSCs. A stronger aggregation property in solution, higher thermal transition temperatures with higher enthalpies, a larger dipole moment, higher relative dielectric constant, and more linear conformation are exhibited by PB3TCN‐C66. Solar cells employing IT‐4F as the electron acceptor offer power conversion efficiencies (PCEs) of 11.2% and 2.3% for PB3TCN‐C66 and PB3T‐C66, respectively. Morphological characterizations reveal that the PB3TCN‐C66:IT‐4F blend exhibits better π–π paracrystallinity, a contracted domain size, and higher phase purity, consistent with its higher molecular interaction parameter, derived from thermodynamic calculations. Moreover, PB3TCN‐C66 offers a higher open‐circuit voltage and reduced energy loss than most state‐of‐the‐art wide‐bandgap polymers, without the need of additional electron‐withdrawing substituents. Two additional polymers derived from DCT also demonstrate promising performance with a higher PCE of 13.4% being achieved. Thus, DCT represents a versatile and promising building block for constructing high‐performance, low‐cost, conjugated polymers for application in PSCs.

Zhang, Bo↗
DOE OSTI2023

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗
DOE OSTI2022

Self-Aligned Selective Area Front Contacts on Poly -Si/SiO x Passivating Contact c -Si Solar Cells

We report both polarity poly-Si/SiO x passivating contacts in a front/back device configuration may represent the next solar cell architecture after tunnel oxide passivating contacts (TOPCon) cells, but high parasitic absorption in the front poly -Si layer often limits its performance. This work explores a wet etching technique to remove the front poly -Si in the nonmetallized regions using self-aligned metal grids as an etch mask. We systematically examine various dielectric layers (SiN x ,Al 2 O 3 , and stacks thereof) to study the repassivation of the etched n + surface, and find that an SiN x /Al 2 O 3 passivation stack can effectively repassivate the etched surface, which we attribute to field-effect passivation from the positive fixed charge from the SiN x layer, and excellent chemical passivation property from Al 2 O 3 in the form of atomic H. We demonstrate a front/back poly-Si/SiO x passivating contact device, with an open-circuit voltage (V oc ) of 690 mV, short-circuit current density (J sc ) of 39.8 mA/cm 2 , fill factor of 78%, and power conversion efficiency of 21.4%. Furthermore, simulations using SunSolve and Quokka 3 show good agreement with both the optical and electrical properties of the experimental device. The power loss analysis reveals improvements in the optical loss from the back Ti adhesion and front SiN x layers would lead to a 23.5% device. Lastly, a techno-economic model compares the production cost of this improved cell with the current TOPCon cells. Our results highlight that further cost reductions in single-sided doped poly -Si layers are needed to compete with mainstream passivated emitter and rear cell, and TOPCon technologies.

14 SOLAR ENERGY↗
DOE OSTI2022

Hydrogen Transport from Dielectrics to poly-Si/SiOx Passivating Contacts Measured by Mass Spectrometry and Vibrational Spectroscopy

We demonstrate the relationship between Si solar cell passivation and hydrogen content of various passivating films, including hydrogenated amorphous silicon (a-Si:H), aluminum oxide (Al2O3), silicon nitride (SiNx) and combinations thereof. Through isotopic studies using quadrupole mass spectrometry (QMS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy, we determine how hydrogen content and stability within each type of film relates to final passivation quality of solar cell test structures. Si solar cells using polycrystalline silicon on silicon oxide (poly-Si/SiOx) passivating contacts are at the forefront of Si solar cell research and emerging as top performers within industrial production. Performance of passivating contact Si solar cells is largely determined by a parameter known as the open-circuit voltage Voc, which directly relates to material quality within the bulk of the device and at surfaces. High Voc is achieved when defects within the bulk crystalline silicon (c-Si) and at interfaces are passivated, preventing them from acting as charge carrier recombination centers. One of the most important means of passivating defects within Si solar cells is via hydrogenation, injecting the cells with large amounts of H to satisfy dangling bonds in the bulk and at interfaces. Hydrogen is especially important in deactivating a prevalent defect in industrial p-type devices which leads to decreased device performance over long-term exposure to light, called light-induced degradation (LID). Some of the most common materials used to supply H to devices are a-Si:H, Al2O3, and SiNx, which can contain very large amounts of H. Upon annealing at elevated temperatures, the hydrogen becomes mobile enough to find and disable defect sites. However, too much hydrogen can also be problematic, sometimes leading to an effect called light and elevated temperature induced degradation (LeTID). It has been shown that these films passivate the interfaces of poly-Si passivating contacts differently, leading to differing performance. Though Al2O3 is a well-defined dielectric material, SiNx can have many different values of x depending on precursor gases and deposition conditions. We observe different FTIR and Raman spectra from different SiNx over a range of x values films to determine the bonding environments within them and further correlate the relative concentrations of Si, N, and H to the stability of H within SiNx and the passivation performance of each film. Because deuterium is chemically identical to hydrogen within these systems, but gives different signals in FTIR and Raman spectroscopy as well as in QMS, isotopic substitution can be used as an excellent tool to probe the H within films. In addition to measuring the H and D bonding within films using FTIR and Raman spectroscopy, we will use such isotopic experiments to observe H and D movement out of these hydrogenating films at elevated temperatures using QMS to determine the stability of H bonding within such systems. With these films characterized based on elemental composition, we will relate such measurements to passivation quality of these films and combinations thereof on poly-Si/SiOx contact structures using quasi-steady state photoconductance decay measurements to obtain implied open-circuit voltage (iVoc) and saturation current density J0 values. Such investigations into the performance of different passivating films and film stacks will lead to greater understanding of dielectrics in semiconductor devices, further improvements in passivated contact design, and eventually, greater proliferation of renewable solar energy worldwide.

Al2O3↗
DOE OSTI2023

Mechanism of Hydrogen Passivation in Passivated Contact Si Solar Cells

In this abstract, we discuss the mechanism of hydrogen passivation on symmetrical n-Si/ultra-thin SiO2/polySi structures. The hydrogen was introduced from different hydrogen-containing dielectric layers (AlOx:H and SiNx:H and their stacks), as well as by forming gas anneal (FGA). The effusion of hydrogen both from the dielectric layers and in the underlying poly-Si was explored using a quadrupole mass spectrometer (QMS) and FTIR spectroscopy. We show that the strength of hydrogen bonds depend on the deposition technique as well as hydrogenation mechanism. While a PECVD SiNx:H loses hydrogen at a peak temperature of ~450 degrees C, LPCVD SiNx:H, although having less hydrogen compared to PECVD, effuses at a peak temperature of ~850 degrees C. This becomes important to maintain passivation of passivated contacts after firing of metal contacts at high temperatures. On the other hand, it has been observed that SiNx:H provides larger amount of hydrogen to poly-Si after FGA compared to FGA treated AlOx:H, which acts as a capping layer and helps in retaining the hydrogen up to higher temperatures.

hydrogen bonding configuration↗
DOE OSTI2022

Deterministic fabrication of 3D/2D perovskite bilayer stacks for durable and efficient solar cells

Realizing solution-processed heterostructures is a long-enduring challenge in halide perovskites because of solvent incompatibilities that disrupt the underlying layer. By leveraging the solvent dielectric constant and Gutmann donor number, we could grow phase-pure two-dimensional (2D) halide perovskite stacks of the desired composition, thickness, and bandgap onto 3D perovskites without dissolving the underlying substrate. Characterization reveals a 3D–2D transition region of 20 nanometers mainly determined by the roughness of the bottom 3D layer. Thickness dependence of the 2D perovskite layer reveals the anticipated trends for n-i-p and p-i-n architectures, which is consistent with band alignment and carrier transport limits for 2D perovskites. Here we measured a photovoltaic efficiency of 24.5%, with exceptional stability of T 99 (time required to preserve 99% of initial photovoltaic efficiency) of >2000 hours, implying that the 3D/2D bilayer inherits the intrinsic durability of 2D perovskite without compromising efficiency.

14 SOLAR ENERGY↗
DOE OSTI2025

Microwave Annealing for Fast and Effective Hydrogen Activation in Polycrystalline Silicon Passivating Contacts

Hydrogenation is a crucial step in the fabrication of high-efficiency silicon solar cells. In this study, the effectiveness of hydrogen activation is demonstrated via microwave annealing of hydrogen-rich dielectrics coated on poly-Si passivating contacts. This method is compared with conventional hydrogenation techniques, such as annealing in N2 in the presence of a hydrogen-rich source (such as hydrogenated aluminum oxide (AlOx:H), hydrogenated silicon nitride (SiNy:H), or a AlOx:H/SiNy:H stack). Key improvements observed include a reduction in J0 from 30 to <5 fA cm-2, an increase in iVoc from 690 to >730 mV, and an enhancement in effective lifetime (teff) from 0.6 to ~3.5 milliseconds on phosphorus-doped poly-Si/SiO2 passivating contact samples. With a very short annealing time of ~1-2 min, the samples passivated by AlOx:H, SiNy:H, or the stack show similar performance to samples subjected to 30 min of nitrogen annealing. Photoluminescence (PL) spectra corroborate the findings regarding the hydrogenation of the poly-Si layer and the c-Si substrate, with an increase in PL intensity after microwave annealing. Ultimately, this work suggests that microwave annealing could be a promising addition, offering flexibility to traditional firing hydrogenation processes.

hydrogenation↗
DOE OSTI2025

Self‐Assembled Monolayer Templating for Engineered Nanopinholes in Passivated Contact Solar Cells

We present a novel self-assembled monolayer (SAM)-based technique to make nanopinhole-enabled passivated contacts on silicon solar cells by tuning the SAM coverage area and etch selectivity. We deposit trimethyl-silyl Si(CH 3 ) 3 groups using hexamethyldisilazane (HMDS) as the precursor over passivating dielectric layers and their stacks (SiO 2 , SiN x , SiO 2 /SiN x ) and interrupt the HMDS attachment chemistry shortly before a full monolayer is formed on its surface. Subsequent etching in dilute HF produces pinholes through the dielectric layers due to the higher etch resistance of the SAM to HF etching. The pinhole areal density (10 4 –10 8 /cm 2 ) and size (10–1000 nm) can be tuned both by duration of HMDS attachment and HF etch time. Pinholes were characterized by atomic force microscopy, tetramethylammonium hydroxide (TMAH) selective etch, and Ag decoration by electroless plating. Polysilicon (poly-Si) passivated contacts enabled by pinholes were formed by subsequent deposition of doped amorphous silicon (a-Si:H) followed by thermal crystallization and dopant drive-in. At optimal areal pinhole density ≈10 7 /cm 2 , contacts exhibit both passivation and carrier transport via pinholes as evidenced by electron beam induced current, transmission line measurements, and carrier lifetime measurements. Solar cells based with these pinhole contacts show V oc = 723 mV and FF = 80.3%. The remaining SAM layer does not affect device performance.

14 SOLAR ENERGY↗
DOE OSTI2025

Poly-Si Passivating Contacts Hydrogenation by Microwave Annealing

Hydrogenation is a crucial step in the fabrication of high-efficiency silicon solar cells. In this study, we demonstrate the for the first time effectiveness of hydrogen activation via microwave annealing of hydrogen-rich dielectrics coated on poly-Si passivating contacts. This method is compared with conventional hydrogenation techniques, such as annealing in N2 in the presence of a hydrogen-rich source (such as hydrogenated aluminum oxide (AlOx:H), hydrogenated silicon nitride (SiNy:H), or a AlOx:H/SiNy:H stack). Key improvements observed include a reduction in J0 from 30 to <5 fA/cm2, an increase in iVoc from 690 to >730 mV, and an enhancement in effective lifetime (teff) from 0.6 to ~3.5 milliseconds on phosphorus-doped poly-Si/SiO2 passivating contact samples. With a very short annealing time of ~1-2 minutes, the samples passivated by AlOx:H, SiNy:H, or the stack show similar performance to samples subjected to 30 minutes of nitrogen annealing. Photoluminescence (PL) spectra corroborate our findings regarding the hydrogenation of the poly-Si layer and the c-Si substrate, with an increase in PL intensity after microwave annealing. Ultimately, our work suggests that microwave annealing could be a promising addition, offering flexibility to traditional firing hydrogenation processes.

14 SOLAR ENERGY↗