Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation slip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Plastic deformation of silicon dendritic web ribbons during the growth

The distribution of slip dislocations in silicon dendritic web ribbons due to plastic deformation during the cooling phase of the growth was studied. The results show the existence of two distinguishable stress regions across the ribbon formed during the plastic deformation stage, namely, shear stress at the ribbon edges and tensile stress at the middle. In addition, slip dislocations caused by shear stress near the edges appear to originate at the twin plane.

Cheng, L. J.↗
NASA NTRS2017

The Evolution of the Deformation Substructure in a Ni-Co-Cr Equiatomic Solid Solution Alloy

The equiatomic NiCoCr alloy exhibits an excellent combination of strength and ductility, even greater than the FeNiCrCoMn high entropy alloy, and also displays a simultaneous increase in strength and ductility with decreasing the testing temperature. To systemically investigate the origin of the exceptional properties of NiCoCr alloy, which are related to the evolution of the deformation substructure with strain, interrupted tensile testing was conducted on the equiatomic NiCoCr single-phase solid solution alloy at both cryogenic and room temperatures at five different plastic strain levels of 1.5%, 6.5%, 29%, 50% and 70%. The evolution of deformation substructure was examined using electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), conventional transmission electron microscopy (CTEM), diffraction contrast imaging using STEM (DCI-STEM) and atomic resolution scanning transmission electron microscopy. While the deformation substructure mainly consisted of planar dislocation slip and the dissociation of dislocations into stacking faults at small strain levels (≤6.5%), at larger strain levels, additional substructures including nanotwins and a new phase with hexagonal close packed (HCP) lamellae also appeared. The volume fraction of the HCP lamellae increases with increasing deformation, especially at cryogenic temperature. First principles calculations at 0 K indicate that the HCP phase is indeed energetically favorable relative to FCC for this composition. The effects of the nanotwin and HCP lamellar structures on hardening rate and ductility at both cryogenic and room temperature are qualitatively discussed.

Twinning↗
NASA NTRS1979

An acoustic emission study of plastic deformation in polycrystalline aluminium

Acoustic emission experiments were performed on polycrystalline and single crystal 99.99% aluminum while undergoing tensile deformation. It was found that acoustic emission counts as a function of grain size showed a maximum value at a particular grain size. Furthermore, the slip area associated with this particular grain size corresponded to the threshold level of detectability of single dislocation slip events. The rate of decline in acoustic emission activity as grain size is increased beyond the peak value suggests that grain boundary associated dislocation sources are giving rise to the bulk of the detected acoustic emissions.

Bill, R. C.↗
NASA NTRS2001

Superplastic Deformation of ice: Experimental Observations

Creep experiments on fine-grained ice reveal the existence of three creep regimes: (1) a dislocation creep regime; (2) a superplastic flow regime in which grain boundary sliding is an important deformation process; and (3) a basal slip creep regime in which the strain rate is limited by basal slip. Dislocation creep in ice is likely climb-limited, is characterized by a stress exponent of 4.0, and is independent of grain size. Superplastic flow is characterized by a stress exponent of 1.8 and depends inversely on grain size to the 1.4 power. Basal slip limited creep is characterized by a stress exponent of 2.4 and is independent of grain size. A fourth creep mechanism, diffusional flow, which usually occurs at very low stresses, is inaccessible at practical laboratory strain rates even for our finest grain sizes of approximately 3 micrometers. A constitutive equation based on these experimental results that includes flow laws for these four creep mechanisms is described. This equation is in excellent agreement with published laboratory creep data for coarse-grained samples at high temperatures. Superplastic flow of ice is the rate-limiting creep mechanism over a wide range of temperatures and grain sizes at stresses less than or equal to 0.1 MPa, conditions which overlap those occurring in glaciers, ice sheets, and icy planetary interiors.

Goldsby, D. L.↗
NASA NTRS1986

Crustal deformation in great California earthquake cycles

Periodic crustal deformation associated with repeated strike slip earthquakes is computed for the following model: A depth L (less than or similiar to H) extending downward from the Earth's surface at a transform boundary between uniform elastic lithospheric plates of thickness H is locked between earthquakes. It slips an amount consistent with remote plate velocity V sub pl after each lapse of earthquake cycle time T sub cy. Lower portions of the fault zone at the boundary slip continuously so as to maintain constant resistive shear stress. The plates are coupled at their base to a Maxwellian viscoelastic asthenosphere through which steady deep seated mantle motions, compatible with plate velocity, are transmitted to the surface plates. The coupling is described approximately through a generalized Elsasser model. It is argued that the model gives a more realistic physical description of tectonic loading, including the time dependence of deep slip and crustal stress build up throughout the earthquake cycle, than do simpler kinematic models in which loading is represented as imposed uniform dislocation slip on the fault below the locked zone.

Li, Victor C.↗
NASA NTRS1993

GPS measurements of crustal deformation associated with the 22 April 1991, Valle de la Estrella , Costa Rica earthquake

Results are presented for analysis of Global Positioning System (GPS) measurements made at sites in Costa Rica in February and July 1991. Significant horizontal and vertical displacements relative to February positions were observed. Differences were found in GPS derived vertical and horizontal displacements as compared to other types of geodetic measurements of uplift in the coastal regions. A slip dislocation model which fits the GPS measured displacement was computed. Differences between these data sets and their associated models were investigated in light of unmodeled slip heterogeneity on the fault and post-seismic displacements.

Lundgren, Paul R.↗
NASA NTRS1990

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗
NASA NTRS1974

Interfaces in directionally solidified eutectics

Consideration of the interface between the phases in directionally solidified eutectic structures with respect to its morphology, crystallography, stability, and overall response to internal and external stress fields. Yielding behavior in such eutectic structures is shown to be controlled by several possible mechanisms. Two that can be related to the interface in directionally-solidified eutectic alloys are: (1) the interaction of slip dislocations with interface dislocations of the semicoherent boundaries, and (2) restrictions of allowable deformation mechanisms in two contiguous phases due to orientation effects. Evidence found thus far for elastic-plastic eutectic composites indicates that interfaces are capable of diverting fatigue cracks parallel to the loading axis.

Hertzberg, R. W.↗
NASA NTRS1983

Rhombohedral twinning in alumina

Alumina single crystals were deformed in compression along the c axes at temperatures of 625 to 1373 K. Large scale deformation by rhombohedral twinning was observed at a constant resolved shear stress of only 12.6 MPa between about 900 and 1373 K. Below 900 K, the twinning stress for specimens with ground surfaces rose rapidly to 227 MPa at 625 K. A model for twin growth in the absence of dislocation slip is proposed.

Scott, W. D.↗
NASA NTRS1984

Recombination-active defects in silicon ribbon and polycrystalline solar cells

This paper reports results from a study of recombination-active structural defects in silicon ribbon and polycrystalline solar cells using the electron beam induced current (EBIC) technique in a scanning electron microscope. It is demonstrated that low temperature EBIC measurements can reveal a range of defects that are not observable at room temperature, including slip dislocations in silicon dendritic web ribbons as well as decorated twin boundaries and dislocation complexes in cast polycrystalline silicon solar cell materials.

Cheng, L. J.↗
NASA NTRS1985

Structural defect characterization of silicon dendritic web ribbons

An EBIC study of the cross section of silicon dendritic web ribbon has revealed that recombination-active structural defects are mainly concentrated in the inner part of the ribbon, particularly at and near the twin plane, whereas the material near the surface has significantly fewer defects. An analysis of the distribution of etch pits due to slip dislocations created by shear stress indicates that a minimum in the dislocation density is frequently observed in the ribbon adjacent to the dendrite.

Cheng, L. J.↗
NASA NTRS2006

Molecular-dynamics Simulation-based Cohesive Zone Representation of Intergranular Fracture Processes in Aluminum

A traction-displacement relationship that may be embedded into a cohesive zone model for microscale problems of intergranular fracture is extracted from atomistic molecular-dynamics simulations. A molecular-dynamics model for crack propagation under steady-state conditions is developed to analyze intergranular fracture along a flat 99 [1 1 0] symmetric tilt grain boundary in aluminum. Under hydrostatic tensile load, the simulation reveals asymmetric crack propagation in the two opposite directions along the grain boundary. In one direction, the crack propagates in a brittle manner by cleavage with very little or no dislocation emission, and in the other direction, the propagation is ductile through the mechanism of deformation twinning. This behavior is consistent with the Rice criterion for cleavage vs. dislocation blunting transition at the crack tip. The preference for twinning to dislocation slip is in agreement with the predictions of the Tadmor and Hai criterion. A comparison with finite element calculations shows that while the stress field around the brittle crack tip follows the expected elastic solution for the given boundary conditions of the model, the stress field around the twinning crack tip has a strong plastic contribution. Through the definition of a Cohesive-Zone-Volume-Element an atomistic analog to a continuum cohesive zone model element - the results from the molecular-dynamics simulation are recast to obtain an average continuum traction-displacement relationship to represent cohesive zone interaction along a characteristic length of the grain boundary interface for the cases of ductile and brittle decohesion. Keywords: Crack-tip plasticity; Cohesive zone model; Grain boundary decohesion; Intergranular fracture; Molecular-dynamics simulation

Yamakov, Vesselin I.↗
NASA NTRS2006

Challenges and Progress in the Development of High-Temperature Shape Memory Alloys Based on NiTiX Compositions for High-Force Actuator Applications

Interest in high-temperature shape memory alloys (HTSMA) has been growing in the aerospace, automotive, process control, and energy industries. However, actual materials development has seriously lagged component design, with current commercial NiTi alloys severely limited in their temperature capability. Additions of Pd, Pt, Au, Hf, and Zr at levels greater than 10 at.% have been shown to increase the transformation temperature of NiTi alloys, but with few exceptions, the shape memory behavior (strain recovery) of these NiTiX systems has been determined only under stress free conditions. Given the limited amount of basic mechanical test data and general lack of information regarding the work attributes of these materials, a program to investigate the mechanical behavior of potential HTSMAs, with transformation temperatures between 100 and 500 C, was initiated. This paper summarizes the results of studies, focusing on both the practical temperature limitations for ternary TiNiPd and TiNiPt systems based on the work output of these alloys and the ability of these alloys to undergo repeated thermal cycling under load without significant permanent deformation or "walking". These issues are ultimately controlled by the detwinning stress of the martensite and resistance to dislocation slip of the individual martensite and austenite phases. Finally, general rules that govern the development of useful, high work output, next-generation HTSMA materials, based on the lessons learned in this work, will be provided

Padula, Santo, II↗
NASA NTRS1989

The low cycle fatigue deformation response of a single-crystal superalloy at 650 C

The cyclic stress-strain response and the associated deformation structure of the single crystal nickel-base superalloy PWA 1480 were investigated. Specimens of various crystallographic orientations were tested in low-cycle fatigue (LCF) at 650 C, resulting in a significant tension-compression anisotropy in initial yield strength associated with the shearing of gamma-prime precipitates by dislocation pairs, and a LCF cyclic hardening of the crystals associated with dislocation interactions occurring in the gamma phase. In specimens deforming by slip on a single slip system, dislocations of the primary slip system accumulated in the gamma matrix and formed seesile entanglements. In specimens deforming by slip on several slip systems, the dislocations of the different operative slip systems intersected in the gamma matrix and formed sessile arrangements.

Gabb, T. P.↗
NASA NTRS1989

On the mechanism of cross slip in Ni3Al

The mechanical properties of L1(2) intermetallic alloys have been previously described by models based on the assumption that cube cross slip is the rate-limiting step. In this study, it was demonstrated that the cube cross-slip event must be reversible under a change in loading direction. This observation allows the cross-slip models to remain consistent with cyclic deformation data. Additionally, this observation was used as a critical test of the available cross-slip models. It was demonstrated that the rate-limiting step cannot be a total cross-slip event, in which both a/2 110-line superpartial dislocations cross slip to the cube plane. Conversely, the limited cross-slip event proposed by Paidar et al. (1984), was demonstrated to be consistent with the reversibility constraint. This lends additional experimental support to this model.

Milligan, Walter W.↗
NASA NTRS1986

Dislocation mechanism based model for stage II fatigue crack propagation rate

Repeated plastic deformation, which of course depends on dislocation mechanism, at or near the crack tip leads to the fatigue crack propagation. By involving the theory of thermally activated flow and the cumulative plastic strain criterion, an effort is made here to model the stage II fatigue crack propagation rate in terms of the dislocation mechanism. The model, therefore, provides capability to ascertain: (1) the dislocation mechanism (and hence the near crack tip microstructures) assisting the crack growth, (2) the relative resistance of dislocation mechanisms to the crack growth, and (3) the fracture surface characteristics and its interpretation in terms of the dislocation mechanism. The local microstructure predicted for the room temperature crack growth in copper by this model is in good agreement with the experimental results taken from the literature. With regard to the relative stability of such dislocation mechanisms as the cross-slip and the dislocation intersection, the model suggests an enhancement of crack growth rate with an ease of cross-slip which in general promotes dislocation cell formation and is common in material which has high stacking fault energy (produces wavy slips). Cross-slip apparently enhances crack growth rate by promoting slip irreversibility and fracture surface brittleness to a greater degree.

Mazumdar, P. K.↗
NASA NTRS1985

Dislocation model for aseismic fault slip in the transverse ranges of Southern California

Geodetic data at a plate boundary can reveal the pattern of subsurface displacements that accompany plate motion. These displacements are modelled as the sum of rigid block motion and the elastic effects of frictional interaction between blocks. The frictional interactions are represented by uniform dislocation on each of several rectangular fault patches. The block velocities and fault parameters are then estimated from geodetic data. Bayesian inversion procedure employs prior estimates based on geological and seismological data. The method is applied to the Transverse Ranges, using prior geological and seismological data and geodetic data from the USGS trilateration networks. Geodetic data imply a displacement rate of about 20 mm/yr across the San Andreas Fault, while the geologic estimates exceed 30 mm/yr. The prior model and the final estimates both imply about 10 mm/yr crustal shortening normal to the trend of the San Andreas Fault. Aseismic fault motion is a major contributor to plate motion. The geodetic data can help to identify faults that are suffering rapid stress accumulation; in the Transverse Ranges those faults are the San Andreas and the Santa Susana.

Cheng, A.↗