Search NASA⌕ Search

SEARCH · Search NASA

Results for “fibers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The optimal fiber volume fraction and fiber-matrix property compatibility in fiber reinforced composites

Although the question of minimum or critical fiber volume fraction beyond which a composite can then be strengthened due to addition of fibers has been dealt with by several investigators for both continuous and short fiber composites, a study of maximum or optimal fiber volume fraction at which the composite reaches its highest strength has not been reported yet. The present analysis has investigated this issue for short fiber case based on the well-known shear lag (the elastic stress transfer) theory as the first step. Using the relationships obtained, the minimum spacing between fibers is determined upon which the maximum fiber volume fraction can be calculated, depending on the fiber packing forms within the composites. The effects on the value of this maximum fiber volume fraction due to such factors as fiber and matrix properties, fiber aspect ratio and fiber packing forms are discussed. Furthermore, combined with the previous analysis on the minimum fiber volume fraction, this maximum fiber volume fraction can be used to examine the property compatibility of fiber and matrix in forming a composite. This is deemed to be useful for composite design. Finally some examples are provided to illustrate the results.

Pan, Ning↗
DOE OSTI2026

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗
DOE OSTI2025

Development of fiber orientation in injection molding: Comparison of glass fiber, carbon fiber and their hybrid composites

Fiber orientation distribution (FOD) in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for glass fiber (GF), carbon fiber (CF), and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varied with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Parallel Information Processing (Image Transmission Via Fiber Bundle and Multimode Fiber

Growing demand for visual, user-friendly representation of information inspires search for the new methods of image transmission. Currently used in-series (sequential) methods of information processing are inherently slow and are designed mainly for transmission of one or two dimensional arrays of data. Conventional transmission of data by fibers requires many fibers with array of laser diodes and photodetectors. In practice, fiber bundles are also used for transmission of images. Image is formed on the fiber-optic bundle entrance surface and each fiber transmits the incident image to the exit surface. Since the fibers do not preserve phase, only 2D intensity distribution can be transmitted in this way. Each single mode fiber transmit only one pixel of an image. Multimode fibers may be also used, so that each mode represent different pixel element. Direct transmission of image through multimode fiber is hindered by the mode scrambling and phase randomization. To overcome these obstacles wavelength and time-division multiplexing have been used, with each pixel transmitted on a separate wavelength or time interval. Phase-conjugate techniques also was tested in, but only in the unpractical scheme when reconstructed image return back to the fiber input end. Another method of three-dimensional imaging over single mode fibers was demonstrated in, using laser light of reduced spatial coherence. Coherence encoding, needed for a transmission of images by this methods, was realized with grating interferometer or with the help of an acousto-optic deflector. We suggest simple practical holographic method of image transmission over single multimode fiber or over fiber bundle with coherent light using filtering by holographic optical elements. Originally this method was successfully tested for the single multimode fiber. In this research we have modified holographic method for transmission of laser illuminated images over commercially available fiber bundle (fiber endoscope, or fiberscope).

Kukhtarev, Nicholai↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The Significance of Multi-Size Carbon Fibers on the Mechanical and Fracture Characteristics of Fiber Reinforced Cement Composites

One of the main challenges of using a high fiber volume content in a cement composite is the narrow margin of fiber volume content beyond which fibers can cause an adverse effect on the mechanical properties. In this paper, the significance of fiber size distribution and fiber volume content of different proportions of chopped and milled carbon microfibers are investigated. The mixes’ flowability showed improvement with altering the fiber size distribution despite having a high fiber content. Uniaxial compression cylinders and unnotched and notched beams were cast and then tested at 7 and 28 days of age. It was found that the compressive strength is significantly affected by fiber size distribution more than fiber volume content. On the other hand, the modulus of rupture and fracture toughness are proportional to the fiber volume content with little effect of fiber size distribution. Finally, neither high fiber volume content nor altered fiber size distribution significantly affected the elastic modulus of the fiber cement composites.

Abdellatef, Mohammed↗
NASA NTRS1994

Monitoring Fiber Stress During Curing of Single Fiber Glass- and Graphite-Epoxy Composites

The difference in thermal expansion characteristics of epoxy matrices and graphite fibers can produce significant residual stresses in the fibers during curing of composite materials. Tests on single fiber glass-epoxy and graphite-epoxy composite specimens were conducted in which the glass and graphite fibers were preloaded in tension, and the epoxy matrix was cast around the fibers. The fiber tension was monitored while the matrix was placed around the fiber and subjected to the temperature-time curing cycle. Two mechanisms responsible for producing stress in embedded fibers were identified as matrix thermal expansion and contraction and matrix cure shrinkage. A simple analysis based on the change in fiber tension during the curing cycle was conducted to estimate the produced stresses. Experimental results on single fiber glass- and graphite-epoxy composites show that the fiber was subjected to significant tensile stresses when the temperature was raised from the first to the second dwell period. When initial fiber pretension is about 60 percent of the fiber failure load, these curing-induced stresses can cause tensile fracture of the embedded fiber.

Madhukar, Madhu S.↗
NASA NTRS2019

Single-mode Fiber and Few-Mode Fiber Photonic Lanterns Performance Evaluated for Use in a Scalable Real-Time Photon Counting Ground Receiver

Photonic lanterns provide an efficient way of coupling light from a single large-core fiber to multiple small-core fibers. This capability is of interest for space to ground communication applications. In these applications, the optical ground receivers require high-efficiency coupling from an atmospherically distorted focus spot to multiple fiber coupled single pixel super-conducting nanowire detectors. This paper will explore the use of photonic lanterns in a real-time ground receiver that is scalable and constructed with commercial parts. The number of small-core fibers that make a photonic lantern determines the number of spatial modes that they couple. For instance, lanterns made with n number of single-mode fibers can couple n number of spatial modes. Although the laser transmitted from a spacecraft originates as a Gaussian shape, the atmosphere distorts the beam profile by scattering energy into higher-order spatial modes. Therefore, if a ground receiver is sized for a target data rate with n number of detectors, the corresponding lantern made with single-mode fibers will couple n number of spatial modes. The energy of the transmitted beam scattered into spatial modes higher than n will be lost. This paper shows this loss may be reduced by making lanterns with few-mode fibers instead of single-mode fibers, increasing the number of spatial modes that can be coupled and therefore increasing the coupling efficiency to single pixel, single photon detectors. The free space to fiber coupling efficiency of these two types of photonic lanterns are compared over a range of the free-space coupling numerical apertures and mode field diameters. Results indicate the few mode fiber lantern has higher coupling efficiency for telescopes with longer focal lengths under higher turbulent conditions. Also presented is analysis of the jitter added to the system by the lanterns, showing the few-mode fiber photonic lantern adds more jitter than the single-mode fiber lantern, but less than a multimode fiber.

photon counting↗
DOE OSTI2023

Exploration of fibers produced from petroleum based-mesophase pitch and pet blends for carbon fiber production

Petroleum-derived mesophase pitch and polyethylene terephthalate (PET) were blended and melt-extruded to create precursor fibers. The raw blends, heat treated bulk materials, and fibers were all examined to determine compatibility between petroleum-derived mesophase pitch and PET. Thermal investigation of the raw blends showed the presence of both the pitch and PET in separate phases suggesting no interactions had occurred during mixing. Here, the heat-treated bulk material also showed multiple phases under polarized light while Fourier-transform infrared spectroscopy indicated that the two materials did not fully separate during extrusion. Elemental scans of the precursor fibers showed areas of high oxygen concentrations averaging 11.7% as compared to a 2% oxygen concentration across the majority of the cross-section. Tensile tests of the precursor fibers showed a decrease in average modulus as compared to pure pitch fibers; however, the depressed modulus of the blended fibers was found to be independent of the PET weight percentage. Fibers created from 5 wt.% PET had a strength value within 10% of pure pitch and a 200% increase in modulus and were therefore found to be the most promising for carbon fiber production. Pure pitch and the 5 wt.% PET fibers were stabilized and carbonized to 1000 °C. Both types of fibers were tensile tested to determine their strength and stiffness. Pure pitch carbon fibers maintained a higher strength while the carbon fibers produced from 5 wt.% PET possessed a stiffer modulus which can be attributed to their radial microstructure.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Importance of Measuring SiC Fiber Diameter Prior to Conducting Fiber Stress Rupture / Creep Tests?

A very significant amount of SiC fiber creep / stress rupture data has been generated and reported in the past by various researchers. Due to the difficulty of measuring fiber diameter and the amount of time required to make accurate measurements, researchers have quite often used an accepted average diameter value (which is fiber type-dependent) when determining the load that will be applied to a fiber to generate a specific stress during testing. Of course, this approach has less of an effect on data scatter when the individual fibers in a tow have very similar diameters (minimal fiber-to-fiber variation in diameter). NASA GRC has begun using a laser fiber diameter measurement system, and we are considering eventually characterizing each SiC fiber prior to testing in creep/stressed oxidation. The laser system will be described in this presentation, as well as examples of fiber diameter data obtained in the past at AFRL. We are currently discussing the merits of using an average diameter in testing/data analysis vs. using a measured or "known" diameter. Information about our current intermediate temperature SiC fiber stress rupture testing will also be provided.

ceramic matrix composites↗
DOE OSTI2021

Reclaimed Carbon Fiber Reinforced Automotive Part Using 3-DEP® Preforming Technology on Additive Manufacturing Tool Made with Reclaimed Carbon Fibers

The project focused on how well tools designed and built using reclaimed carbon fiber on the Big Area Additive Manufacturing (BAAM) can be used to manufacture preforms made with reclaimed carbon fibers. The project supported multiple Institute for Advanced Composite Manufacturing Innovation (IACMI) goals: • Enables the use of recycled carbon fibers in two areas: o Tooling material compounded with reclaimed carbon fiber. o Preforms made with recycled carbon fiber (rCF). • Lowers manufacturing costs by producing low cost 3-DEP® preform tooling. • Reduces manufacturing cycle time with quick additive manufacturing techniques. • Produces lightweight automotive components that will increase fuel economy which will in turn reduce greenhouse gas emissions. The project demonstrated a tool made from reclaimed carbon fibers, gathered technical data that will guide optimization of tooling materials, evaluated preforms made with the BAAM printed tool, and developed cost evaluations. This project has been a total success. First the project demonstrated that reclaimed carbon fiber can be compounded and successfully printed in the BAAM equipment. Second preforms were successfully made from reclaimed carbon fiber using a reclaimed fiber printed tool. Third the team successfully printed a molding tool out of reclaimed carbon fiber. Fourth the project went beyond the scope of this phase I project in 3 areas: (1)- Techmer PM compounded rCF in 2 resin systems instead of just one system (2)- Local Motors evaluated and collected data that will support their IACMI 3.6 project (Robert Bedsole, 2017) . (3)- University of Tennessee Knoxville (UTK) molded a part using the reclaimed preform on a molding tool made from printed reclaim fiber.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Substitution of virgin carbon fiber with low-cost recycled fiber in automotive grade injection molding polyamide 66 for equivalent composite mechanical performance with improved sustainability

Recycled carbon fiber has historically proven challenging to integrate into composite manufacturing due in no small part to the low-density, randomly oriented, discontinuous fiber format that results from typical recycling. Discontinuous fiber requires the use of alternative technologies than those traditionally applied to continuous fiber (e.g., hand lay-up, winding). Extrusion compounding is one such applicable technology, but material transfer into the system requires alternative feeding equipment or the use of an altered procedure as trialed in this research. In this study, an injection molding compound for automotive applications was prepared with recycled carbon fiber and compared against an existing commercial compound. Input fibers and molded compound were evaluated for mechanical performance, while relevant variables such as compounded fiber alignment and aspect ratio were compared to the existing baseline material to confirm a like-for-like composite material structure. Overall, analysis indicates that recycled fiber performs similarly to virgin fiber reinforcement, demonstrating that recycled fiber may be a viable drop-in replacement for short-fiber discontinuous applications.

42 ENGINEERING↗
DOE OSTI2022

Improving OFDR Distributed Fiber Sensing by Fibers With Enhanced Rayleigh Backscattering and Image Processing

This article investigates using optical fibers with enhanced backscattering profiles to improve distributed fiber sensor performance and reduce instrumentation costs. Using a femtosecond (fs) laser direct writing technique, the Rayleigh backscattering profile of a standard telecom fiber was enhanced by more than 40 dB to improve the signal-to-noise ratio (SNR) for optical frequency domain reflectometry (OFDR). The enhanced backscattering signals enable effectively distributed strain measurements using a low-cost tunable laser (TL). Median filtering is applied to denoise cross correlation results to further improve measurement outcomes. Results presented in this article show that a TL with a 1-nm tuning range, which is far less than the tuning range used in commercial OFDR interrogators, can perform effectively distributed strain measurements using sensing fibers with enhanced backscattering profiles. The sensing fiber with over 40-dB backscattering enhancement achieved 4.8-cm spatial resolution in strain measurements with a root mean square accuracy of less than 2.70 με when 10–50 με were exerted to the sensing fiber. In conclusion, results presented in this article reveal both the potential and limitations of sensing fibers with enhanced backscattering for OFDR-based distributed fiber sensors.

42 ENGINEERING↗
DOE OSTI2022

Extracting single fiber transverse and shear moduli from off-axis misalignment fiber tensile testing

Small diameter (<100 μm) fibers (e.g. carbon fibers, Kevlar, and fiberglass) and wires (e.g. ultrafine copper and aluminum wires) are frequently used in many different engineering applications, such as for light weighting structures, electromagnetic shielding for aircraft/infrastructure/EVs, vibration damping, biological sensors, aerospace electrical devices, and electric windings just to name a few. Due to the manufacturing process, the fibers and wires are pulled and stretched to produce a preferential alignment. Therefore, thin fibers and wires typically display different properties along the length of the fiber as opposed to their cross section and many fibers/wires are considered transversely isotropic. The axial properties of fibers/wires can be ascertained via tensile testing of single-filaments or fiber tows, but the radial properties require much more effort to measure. Knowing these properties is important for the accurate prediction of micromechanical models and manipulation of fibers during micromanufacturing. In this paper, a new technique was developed to determine the transverse/shear moduli and strength of a material by conducting tensile tests of the material at increasing misalignment angles from the tensile axis. Due to the transversely isotropic nature of the material, the transverse/shear moduli and strength influence the experimental results recorded by the test machine to different degrees based on the amount of misalignment in the test setup. An equation was derived to determine the influence of each of the material properties based on the misalignment angle by manipulating the stiffness matrix for transversely isotropic materials using the transformation matrices. Then, curve fitted coefficients were used to identify the material properties. Here, the strengths were similarly determined by curve fitting an off-axis Tsai-Hill failure criteria to determine the influence of transverse, shear, and tensile strengths based on the complex loading condition provided by the off-axis tensile test. Zoltek Panex 35 carbon fibers were used to demonstrate this new technique and the determined properties were then compared to those obtained from nanoindentation and from literature. Fracture surfaces provide insight into the different failure mechanisms at various misalignment angles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hong-Ou-Mandel interference with a coexisting clock using transceivers for synchronization over deployed fiber

Interference between independently generated photons is a key step towards distributing entanglement over long distances, but it requires synchronization between the distantly-located photon sources. Synchronizing the clocks of such photon sources using coexisting two-way classical optical communications over the same fiber that transports the quantum photonic signals is a promising approach for achieving photon-photon interference over long distances, enabling entanglement distribution for quantum networking using the deployed fiber infrastructure. Here, we demonstrate photon-photon interference by observing the Hong-Ou-Mandel dip between two distantly-located sources: a weak coherent-state source obtained by attenuating the output of a laser and a heralded single-photon source. We achieve a maximum dip visibility of 0.58 +/- 0.04 when the two sources are connected via 4.3 km of deployed fiber. Dip visibilities > 0.5 are nonclassical and a first step towards achieving teleportation over the deployed fiber infrastructure. In our experiment, the classical optical communication is achieved with - 21 dBm of optical signal launch power, which is used to synchronize the clocks in the two independent, distantly-located photon sources. The impact of spontaneous Raman scattering from the classical optical signals is mitigated by appropriate choice of the quantum- and classical-channel wavelengths. All equipment used in our experiment (the photon sources and the synchronization setup) is commercially available. Finally, our experiment represents a scalable approach to enabling practical quantum networking with commercial equipment and coexistence with classical communications in optical fiber.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Multi-parameter distributed fiber optic sensing using double-Brillouin peak fiber in Brillouin optical time domain analysis

In this paper, we demonstrate a multi-parameter fiber sensing system based on stimulated Brillouin scattering in a double-Brillouin peak specialty fiber with enhanced Brillouin gain response. The amplitude level of the second Brillouin gain peak, which originated from the higher-order acoustic modes, has been improved with an approximately similar amplitude level to the first Brillouin gain peak from the fundamental acoustic mode. Compared to other multi-Brillouin peak fibers presented in the literature, the proposed fiber significantly reduces the measured Brillouin frequency shift error, thus improving strain and temperature accuracies. By utilizing the sensitivity values of the strain and temperature associated with each Brillouin gain spectrum (BGS) peak, a successful discriminative measurement of strain and temperature is performed with an accuracy of ±13 μɛ, and ±0.5 °C, respectively. The proposed double-Brillouin peak fiber appears to be a possible alternative to other multi-BGS peak fibers, for instance, large effective area fiber and dispersion compensating fibers, which are inherently accompanied by large measurement errors due to the weak Brillouin gain values originating from the higher-order acoustic modes. The demonstrated results show different strain and temperature coefficients of 47 kHz/µɛ, 1.15 MHz/°C for peak 1 and 51 kHz/µɛ, 1.37 MHz/°C for peak 2. Moreover, the enhanced BGS peak gains having nearly the same amplitude levels enable the discriminative measurement of strain and temperature. Such fibers in Brillouin interrogation eliminate the need for complex monitoring setups and reduce measurement errors. We recommend that for long-distance natural gas pipeline monitoring, where discriminative strain and temperature measurement is crucial, the proposed double-Brillouin peak fiber can be highly beneficial.

47 OTHER INSTRUMENTATION↗