Search NASA⌕ Search

SEARCH · Search NASA

Results for “growth-rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Forecast for a growth-rate measurement using peculiar velocities from LSST supernovae

We investigate whether the cosmic growth-rate parameter fσ 8 can be measured using peculiar velocities (PVs) derived from type Ia supernovae (SNe Ia) in the Vera C. Rubin Observatory’s Legacy Survey of Space and Time (LSST). We produced simulations of different SN types using a realistic LSST observing strategy that incorporated noise, a photometric detection from the difference-image analysis (DIA) pipeline, and a PV field modeled from the Uchuu universe machine simulations. We tested three different observational scenarios that ranged from ideal conditions with spectroscopic host galaxy redshifts and spectroscopic SN typing to realistic photometric typing that resulted in a contamination with non-Ia SNe. Using a maximum likelihood technique, we showed that the LSST can measure fσ 8 with a precision of 10% in the redshift range 0.02 < z < 0.14 for our most realistic scenario. In three tomographic bins, the LSST will be able to constrain the growth-rate parameter with errors below 18% up to redshift z = 0.14. We also tested the contamination effect on the maximum likelihood method and found that for a contamination fraction below ∼2%, we recovered unbiased measurements. The results of this analysis highlight that the LSST SN sample is expected to complement traditional redshift-space distortion measurements at high redshift. This will provide a novel avenue for testing general relativity and different dark energy models.

Rosselli, D↗
NASA NTRS1977

Growth-rate periodicity of Streptomyces levoris during space flight

Streptomyces levoris provides a suitable biological test system to investigate the effects of space flight on the rhythms of vegetative and spore phase characteristics of both growth-rate periodicity and culture morphology during the pre-, in-, and post-flight periods of the Apollo-Soyuz Test Project. The objectives of the American participation were to study the effects of space flight on the biorhythms of Streptomyces levoris based on a comparison of the growth-rate periodicity of the vegetative and spore phase within each culture, to examine the possible alteration of spore morphology and development by SEM, and to compare the effects of a 12-hr phase shift on the periodic growth characteristics of this microorganism in cultures which were exchanged during the joint activities of the space flight. No uniform differences in the biorhythm of Streptomyces levoris during space flight were observed. It appears that the single most variable factor related to the experiment was the lack of temperature control for the space-flight specimens.

Rogers, T. D.↗
DOE OSTI2025

Type Ia Supernova Growth-rate Measurement with LSST Simulations: Intrinsic Scatter Systematics

Measurement of the growth rate of structures (fσ 8 ) with Type Ia supernovae (SNe Ia) will improve our understanding of the nature of dark energy and enable tests of general relativity. In this paper, we generate simulations of the 10 yr SN Ia data set of the Rubin-LSST survey, including a correlated velocity field from an N-body simulation and realistic models of SNe Ia properties and their correlations with host-galaxy properties. We find, similar to SN Ia analyses that constrain the dark energy equation-of-state parameters w 0 w a , that constraints on fσ 8 can be biased depending on the intrinsic scatter of SNe Ia. While for the majority of intrinsic scatter models we recover fσ 8 with a precision of ∼13%–14%, for the most realistic dust-based model, we find that the presence of non-Gaussianities in Hubble diagram residuals leads to a bias on fσ 8 of ∼ −20%. When trying to correct for the dust-based intrinsic scatter, we find that the propagation of the uncertainty on the model parameters does not significantly increase the error on fσ 8 . We also find that while the main component of the error budget of fσ 8 is the statistical uncertainty (>75% of the total error budget), the systematic error budget is dominated by the uncertainty on the damping parameter, σ u , that gives an empirical description of the effect of redshift space distortions on the velocity power spectrum. Our results motivate a search for new methods to correct for the non-Gaussian distribution of the Hubble diagram residuals, as well as an improved modeling of the damping parameter.

Carreres, Bastien [Duke Univ., Durham, NC (United ↗
DOE OSTI2024

An extended variational method for the resistive wall mode in toroidal plasma confinement devices

The external-kink stability of a toroidal plasma surrounded by a rigid resistive wall is investigated. The well-known analysis of Haney and Freidberg is rigorously extended to allow for a wall that is sufficiently thick that the thin-shell approximation does not necessarily hold. A generalized Haney–Freidberg formula for the growth-rate of the resistive wall mode is obtained. Thick-wall effects do not change the marginal stability point of the mode but introduce an interesting asymmetry between growing and decaying modes. Growing modes have growth-rates that exceed those predicted by the original Haney–Freidberg formula. On the other hand, decaying modes have decay-rates that are less than those predicted by the original formula. The well-known Hu–Betti formula for the rotational stabilization of the resistive wall mode is also generalized to take thick-wall effects into account. Increasing wall thickness facilitates the rotational stabilization of the mode, because it decreases the critical toroidal electromagnetic torque that the wall must exert on the plasma. On the other hand, the real frequency of the mode at the marginal stability point increases with increasing wall thickness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Investigation of tearing mode stability near ideal stability boundaries via asymptotic matching techniques

A number of improvements to the TJ toroidal tearing mode code [Fitzpatrick, Phys. Plasmas 31, 102507 (2024)] are documented. The TJ code is also successfully benchmarked against the STRIDE toroidal tearing mode code [Glasser and Koleman, Phys. Plasmas 25, 082502 (2018)]. Finally, the new capabilities of the TJ code are used to investigate the stability of tearing modes in tokamak plasmas as an ideal stability boundary, associated with either an external-kink or an internal-kink mode, is approached. All elements of the tearing stability matrix are found to tend to infinity as an ideal stability boundary is approached. Furthermore, as the stability boundary is approached, the eigenfunctions of the various tearing modes in the plasma, which are decoupled by sheared plasma rotation, are all found to morph into that of the marginally stable ideal mode. However, the growth-rates and real frequencies of the various “ideal-tearing-modes” are different from one another. Moreover, the growth-rate of the ideal-tearing-mode that reconnects magnetic flux at the rational surface that lies closest to the edge of the plasma is the one that tends to a very large value as the stability boundary is approached. A relatively simple test for ideal stability that is capable of detecting stability boundaries for external-kink and internal-kink modes, even in the presence of a very close-fitting ideal wall, is described and verified.

FOS: Physical sciences↗
NASA NTRS1988

Growth and characterization of Hg(1-x)Cd(x)Se alloys

A detailed evaluation of the influence of growth conditions on the radial and axial compositional variations in directionally solidified Hg(1-x)Cd(x)Se alloys was performed. The measured axial compositional profiles were fitted to theoretical profiles to determine the effective solute (CdSe) diffusion coefficient (D) for the Hg(1-x)Cd(x)Se system. The value for D was estimated to be 3.0 + or - 0.5 x 10 to the -5th sq cm/s and did not appear to be significantly affected by the rate of crystal growth. The axial crystal uniformity was shown to be highly growth-rate dependent, with the faster growth rates producing crystals of more uniform composition in the axial direction. The magnitude of the radial variations was also shown to be highly growth-rate dependent, with the slower growth rates producing crystals of greater radial uniformity. This translation rate dependence of the radial uniformity is discussed in terms of lateral solute diffusion and convective interfacial fluid flows.

Andrews, R. N.↗
NASA NTRS1989

Linear instability of supersonic plane wakes

In this paper we present a theoretical and numerical study of the growth of linear disturbances in the high-Reynolds-number and laminar compressible wake behind a flat plate which is aligned with a uniform stream. No ad hoc assumptions are made as to the nature of the undisturbed flow (in contrast to previous investigations) but instead the theory is developed rationally by use of proper wake-profiles which satisfy the steady equations of motion. The initial growth of near wake perturbation is governed by the compressible Rayleigh equation which is studied analytically for long- and short-waves. These solutions emphasize the asymptotic structures involved and provide a rational basis for a nonlinear development. The evolution of arbitrary wavelength perturbations is addressed numerically and spatial stability solutions are presented that account for the relative importance of the different physical mechanisms present, such as three-dimensionality, increasing Mach numbers enough (subsonic) Mach numbers, there exists a region of absolute instability very close to the trailing-edge with the majority of the wake being convectively unstable. At higher Mach numbers (but still not large-hypersonic) the absolute instability region seems to disappear and the maximum available growth-rates decrease considerably. Three-dimensional perturbations provide the highest spatial growth-rates.

Papageorgiou, D. T.↗
NASA NTRS1975

Growth of surface and corner cracks in beta-processed and mill-annealed Ti-6Al-4V

Empirical stress-intensity expressions were developed to relate the growth of cracks from corner flaws to the growth of cracks from surface flaws. An experimental program using beta-processed Ti-6Al-4V verified these expressions for stress ratios, R greater than or equal to 0. An empirical crack growth-rate expression which included stress-ratio and stress-level effects was also developed. Cracks grew approximately 10 percent faster in transverse-grain material than in longitudinal-grain material and at approximately the same rate in longitudinal-grain mill-annealed Ti-6Al-4V. Specimens having surface and corner cracks and made of longitudinal-grain, beta-processed material were tested with block loads, and increasing the stresses in a block did not significantly change the crack growth rates. Truncation of the basic ascending stress sequence within a block caused more rapid crack growth, whereas both the descending and low-to-high stress sequences slowed crack growth.

Bell, P. D.↗
NASA NTRS1982

Segregation effects during growth of pseudo-binary system with large liquidus-solidus separation

Results are reported for an experimental study of the seeded growth, of PbSnTe single crystals in a vertical Bridgman-Stockbarger (B-S) furnace. Profiles of axial and radial segregation of Sn are presented for crystal growth from melts with aspect ratios of 15 and 6.8; the profiles indicate intense convective mixing. A one-dimensional model of heat and mass transfer in an idealized B-S furnace with diffusion control is used to examine the importance of liquidus-solidus separation in determining growth-rate and composition transients in a pseudobinary system. It is shown that the coupling of heat and mass transfer in a pseudobinary system with a large liquidus-solidus separation causes the transient behavior in a nondilute system to differ markedly from such behavior in a dilute system and that PbSnTe crystals with a reasonable diameter can be grown under nearly convectionless conditions in a microgravity environment.

Bourret, E. D.↗
NASA NTRS1983

Phytoxicity study of the products of wet oxidation of a representative biomass (lettuce)

In an attempt to verify the results reported previously concerning the phytotoxicity of wet-oxidation (wet-ox) products, lettuce solids were suspended in water and then heated to 548 K for 3.6 ksec (1 hr) under 4.1x10 to the -7 Pa (400 psig at 294 K) oxygen pressure and 1.52x10 to the 8th (1500 psig at 548 K) total pressure. Such treatment resulted in oxidation of 80% of the initial organic carbon to carbon dioxide. Thirty-three percent of the remaining organic carbon was present in acetic acid. Organic nitrogen in the feed was decreased 90% by the wet-ox treatment. Ammonia and nitrogen gas were the main nitrogen products. Analysis of the liquid product of wet-ox indicated that most of the minerals essential for plant growth were present. However, when tested using a lettuce-root growth-rate assay, the solution was toxic. This toxicity was not due to excessive salt or ammonia or to an improper pH. Analysis of the wet-ox solution revealed the presence of silver and chromium, thus implicating reactor corrosion as the cause of the phytotoxicity. Both cation and anion exchange resins removed the silver and the toxicity of the liquid effluent, indicating silver as the toxic component. Uptake of both silver and chromium by lettuce roots correlated with diminished root growth. Toxicity of the solution from wet-ox was not observed when precautions were taken to minimize contact of the liquid in the reactor with the metal reactor components.

Onisko, B. L.↗
NASA NTRS1983

The growth of the tearing mode - Boundary and scaling effects

A numerical model of resistive magnetic tearing is developed in order to verify and relate the results of the principal approximations used in analytic analyses and to investigate the solutions and their growth-rate scalings over a large range of primary parameters which include parametric values applicable to the solar atmosphere. The computations cover the linear behavior for a variety of boundary conditions, emphasizing effects which differentiate magnetic tearing in astrophysical situations from that in laboratory devices. Eigenfunction profiles for long and short wavelengths are computed and the applicability of the 'constant psi' approximation is investigated. The growth rate is computed for values of the magnetic Reynolds number up to a trillion and of the dimensionless wavelength parameter down to 0.001. The analysis predicts significant effects due to differing values of the magnetic Reynolds number.

Steinolfson, R. S.↗
NASA NTRS1984

Solid/melt interface studies of high-speed silicon sheet growth

Radial growth-rate anisotropies and limiting growth forms of point nucleated, dislocation-free silicon sheets spreading horizontally on the free surface of a silicon melt have been measured for (100), (110), (111), and (112) sheet planes. Sixteen-millimeter movie photography was used to record the growth process. Analysis of the sheet edges has lead to predicted geometries for the tip shape of unidirectional, dislocation-free, horizontally growing sheets propagating in various directions within the above-mentioned planes. Similar techniques were used to study polycrystalline sheets and dendrite propagation. For dendrites, growth rates on the order of 2.5 m/min and growth rate anisotropies on the order of 25 were measured.

Ciszek, T. F.↗
NASA NTRS1987

A linear MHD instability analysis of solar mass ejections with gravitation

The linear MHD instability of a cylindrical plasma is used to investigate the origin of solar mass ejections, and the dispersion relation is solved numerically. The initial plasma-flow velocity is found to have a significant effect on the instability criteria and growth rate, and the instability growth-rate is shown to be larger in cases where plasma flow exists, relative to the static case. Results suggest that the plasma column may break into small pieces. Assuming a thin-tube approximation, gravity is found to have little effect on the instability of quasi-horizontal ejection, but to have considerable effect on the vertical ejection. In considering the gravitational force, an exact analytical solution is found for the vertical case, while asymptotic solutions are given for the horizontal and oblique cases.

Song, M. T.↗
NASA NTRS1986

Aqueous sodium chloride induced intergranular corrosion of Al-Li-Cu alloys

Two methods have been explored to assess the susceptibility of Al-Li-Cu alloys to intergranular corrosion in aqueous sodium chloride solution. They are: (1) constant extension rate testing with and without alternate-immersion preexposure and (2) metallographic examination after exposure to a NaCl-H2O2 corrosive solution per Mil-H-6088F. Intergranular corrosion was found to occur in both powder and ingot metallurgy alloys of similar composition, using both methods. Underaging rendered the alloys most susceptible. The results correlate to stress-corrosion data generated in conventional time-to-failure and crack growth-rate tests. Alternate-immersion preexposure may be a reliable means to assess stress corrosion susceptibility of Al-Li-Cu alloys.

Pizzo, P. P.↗
NASA NTRS1989

Growth rate study of canavalin single crystals

The dependence on supersaturation of the growth rate of single crystals of the protein canavalin is studied. In the supersaturation ranges studied, the rate-limiting step for growth is best described by a screw dislocation mechanism associated with interface attachment kinetics. Using a ln-ln plot, the growth-rate data is found to fit a predictive relationship of the form G = 0.012 x the supersaturation to the 6.66, which, together with the solubility curves, allows the growth rate to be estimated under a variety of conditions.

Demattei, R. C.↗
NASA NTRS1992

Stability investigations of airfoil flow by global analysis

As the result of global, non-parallel flow stability analysis the single value of the disturbance growth-rate and respective frequency is obtained. This complex value characterizes the stability of the whole flow configuration and is not referred to any particular flow pattern. The global analysis assures that all the flow elements (wake, boundary and shear layer) are taken into account. The physical phenomena connected with the wake instability are properly reproduced by the global analysis. This enhances the investigations of instability of any 2-D flows, including ones in which the boundary layer instability effects are known to be of dominating importance. Assuming fully 2-D disturbance form, the global linear stability problem is formulated. The system of partial differential equations is solved for the eigenvalues and eigenvectors. The equations, written in the pure stream function formulation, are discretized via FDM using a curvilinear coordinate system. The complex eigenvalues and corresponding eigenvectors are evaluated by an iterative method. The investigations performed for various Reynolds numbers emphasize that the wake instability develops into the Karman vortex street. This phenomenon is shown to be connected with the first mode obtained from the non-parallel flow stability analysis. The higher modes are reflecting different physical phenomena as for example Tollmien-Schlichting waves, originating in the boundary layer and having the tendency to emerge as instabilities for the growing Reynolds number. The investigations are carried out for a circular cylinder, oblong ellipsis and airfoil. It is shown that the onset of the wake instability, the waves in the boundary layer, the shear layer instability are different solutions of the same eigenvalue problem, formulated using the non-parallel theory. The analysis offers large potential possibilities as the generalization of methods used till now for the stability analysis.

Morzynski, Marek↗
NASA NTRS1992

Accretion rates of protoplanets. II - Gaussian distributions of planetesimal velocities

In the present growth-rate calculations for a protoplanet that is embedded in a disk of planetesimals with triaxial Gaussian velocity dispersion and uniform surface density, the protoplanet is on a circular orbit. The accretion rate in the two-body approximation is found to be enhanced by a factor of about 3 relative to the case where all planetesimals' eccentricities and inclinations are equal to the rms values of those disk variables having locally Gaussian velocity dispersion. This accretion-rate enhancement should be incorporated by all models that assume a single random velocity for all planetesimals in lieu of a Gaussian distribution.

Greenzweig, Yuval↗
NASA NTRS1993

Initial development of the two-dimensional ejector shear layer - Experimental results

An experimental investigation designed to study the development of shear layers in a two-dimensional single-nozzle ejector has been completed. In this study, combinations of air/air, argon/air, helium/air, and air/helium were used as the supersonic primary and subsonic secondary, respectively. Mixing of the gases occurred in a constant-area tube 39.1 mm high by 25.4 mm wide, where the inlet static pressure was maintained at 35 kPa. The cases studied resulted in convective Mach numbers between 0.058 and 1.64, density ratios between 0.102 and 3.49, and velocity ratios between 0.065 and 0.811. The resulting data shows the differences in the shear-layer development for the various combinations of independent variables utilized in the investigation. The normalized growth-rates in the near-field were found to be similar to two-dimensional mixing layers. These results have enhanced the ability to analyze and design ejector systems as well as providing a better understanding of the physics.

Benjamin, M. A.↗