SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
High molecular weight polyimide resins have greater than 20 percent /by weight/ solubility in polar organic solvents. They permit fabrication into films, fibers, coatings, reinforced composite, and adhesive product forms. Characterization properties for one typical polyimide resin are given.
High molecular weight perfluorocarbon polyether gums were obtained by photolysis of perfluorodienes and discyl fluorides containing a perfluorocarbon polyether backbond. The materials obtained are represented by chemical formulas. A method was developed whereby reactive acyl fluoride and trifluorovinyl end groups are converted into inert structures. In order to investigate the possible preparation of difunctional molecules which may be useful in polymer synthesis, the reactions of hexafluoropropene oxide (HFPO) with Grignard and organolithium reagents have been studied. Reactions of various nucleophilic reagents with HFPO were also investigated.
High molecular weight products were detected on the wear track of an iron disk at the end of a sliding friction and wear test using benzene as a lubricant. Size exclusion chromagography in conjunction with UV analysis gave evidence that the high molecular weight products are polyphenyl ether type substances. Organic electrochemistry was used to elucidate the possible surface reaction mechanisms.
Process for preparing high molecular weight polyaryloxysilanes from lower molecular weight forms
The high molecular weight aggregate (HMWA) fraction was isolated from the water soluble proteins of aged bovine lenses. Its composition and ability to inhibit heat-induced denaturation and aggregation were compared with the lower molecular weight, oligomeric fraction of alpha isolated from the same lens. Although the major components of both fractions were the alpha-A and alpha-B chains, the HMWA fraction possessed a decreased ability to protect other proteins against heat-induced denaturation and aggregation. Immunoelectron microscopy of both fractions demonstrated that alpha particles from the HMWA fraction contained increased amounts of beta and gamma crystallins, bound to a central region of the supramolecular complex. Together, these results demonstrate that alpha crystallins found in the HMWA fraction possess a decreased ability to protect against heat-induced denaturation and aggregation, and suggest that at least part of this decrease could be due to the increased presence of beta and gamma crystallins complexed to the putative chaperone receptor site of the alpha particles.
Olefins of high molecular weight in microscopic algae, discussing hydrocarbon composition investigation by gas chromatography mass spectrometry
Abstract Topochemical polymerization reactions hold the promise of producing ultra-high molecular weight crystalline polymers. However, the totality of topochemical polymerization reactions has failed to produce ultra-high molecular weight polymers that are both soluble and display variable functionality, which are restrained by the crystal-packing and reactivity requirements on their respective monomers in the solid state. Herein, we demonstrate the topochemical polymerization reaction of a family of para -azaquinodimethane compounds that undergo facile visible light and thermally initiated polymerization in the solid state, allowing for the first determination of a topochemical polymer crystal structure resolved via the cryoelectron microscopy technique of microcrystal electron diffraction. The topochemical polymerization reaction also displays excellent functional group tolerance, accommodating both solubilizing side chains and reactive groups that allow for post-polymerization functionalization. The thus-produced soluble ultra-high molecular weight polymers display superior capacitive energy storage properties. This study overcomes several synthetic and characterization challenges amongst topochemical polymerization reactions, representing a critical step toward their broader application.
This invention provides a high molecular weight polysaccharide capable of binding to and inhibiting virus and related pharmaceutical formulations and methods of inhibiting viral infectivity and/or pathogenicity, as well as immunogenic compositions. The invention further includes methods of inhibiting the growth of cancer cells and of ameliorating a symptom of aging. Additionally, the invention provides methods of detecting and/or quantifying and/or isolating viruses.
This invention provides a high molecular weight polysaccharide capable of binding to and inhibiting virus and related pharmaceutical formulations and methods of inhibiting viral infectivity and/or pathogenicity, as well as immunogenic compositions. The invention further includes methods of inhibiting the growth of cancer cells and of ameliorating a symptom of aging. Additionally, the invention provides methods of detecting and/or quantifying and/or isolating viruses.
Ultra-high molecular weight (UHMW, >10 6 g mol −1 ) vinyl polymers are increasingly accessible through photoiniferter polymerization, yet their behavior in electrospinning has received comparatively little attention. Here, we explore the electrospinning of UHMW poly(methyl acrylate), poly(methyl methacrylate), poly(N,N-dimethylacrylamide), and poly(styrene-co-pentafluorostyrene) synthesized by photoiniferter polymerization, with number-average molecular weights (M n ) greater than 1000 kDa and dispersities below 1.4. UHMW polymers form stable Taylor cones and discrete fibers at solution concentrations as low as 0.5 wt% due to their large number of entanglements, a threshold unachievable with low molecular weight (M n = 20–54 kDa) polymers of the same chemistry. Using poly(methyl methacrylate) and poly(styrene-co-pentafluorostyrene) as model systems, we demonstrate that fiber diameter can be tuned from 350 nm to 20 μm through systematic variation of polymer concentration (0.01 to 4 wt%) and flow rate (0.5 to 10 mL h −1 ). Additionally, we find that collector rotation rate governs fiber alignment, with highly aligned mats obtained with drum rotation speeds of 1000 RPM. Reversing the polarity of the electric field during electrospinning reorients the surface chemistry of these fiber mats without altering their microscale morphology, shifting the water contact angle by 7° (89° to 96°) and providing a two-fold binding capacity enhancement in cationic dye uptake. These results show that the high entanglement densities of UHMW vinyl polymers shift the accessible electrospinning window to dilute solutions and that electric-field polarity is a useful lever to control the surface chemistry in the resulting fibers.
In developed series of high-flow PMR-type polyimide resins, 2, 2'-bis(trifluoromethyl)-4, 4'-diaminobiphenyl (BTDB) substituted for 1, 4-pheylenediamine in PMR-II formulation. Polyimides designated either as PMR-12F when nadic ester (NE) end caps used, or as V-CAP-12F when p-aminostyrene end caps used. High-molecular-weight, addition-curing polyimides based on BTBD and HFDE highly processable high-temperature matrix resins used to make composite materials with excellent retention of properties during long-term exposure to air at 650 degrees F or higher temperature. Furthermore, 12F addition-curing polyimides useful for electronic applications; fluorinated rigid-rod polyimides known to exhibit low thermal expansion coefficients as well as low absorption of moisture.
The damage tolerance of carbon/epoxy was examined when an outer layer of ultra high molecular weight polyethylene (Spectra) material was utilized on the specimen. Four types of 16 ply quasi-isotropic panels, (0,+45,90,-45)s2 were tested. The first contained no Spectra, while the others had one lamina of Spectra placed on either the top (impacted side), bottom or both surfaces of the composite plate. A range of impact energies up to approximately 8.5 Joules (6.3 ft-lbs) was used to inflict damage upon these specimens. Glass/Phenolic honeycomb beams with a core density of 314 N/m3 (2.0 lb/ft3) and 8 ply quasi-isotropic facesheets were also tested for compression-after-impact strength with and without Spectra at impact energies of 1,2,3 and 4 Joules (.74, 1.47, 2.21 and 2.95 ft-lbs). It was observed that the composite plates had little change in damage tolerance due to the Spectra, while the honeycomb panels demonstrated a slight increase in damage tolerance when Spectra was added, the damage tolerance level being more improved at higher impact energies.
The high molecular weight organic products of Fischer-Tropsch/Haber-Bosch syntheses on the surfaces of Fe-silicate catalysts have been studied by GCMS. Additional information is contained in the original extended abstract.
Toxic, hazardous petrochemical solvents are commonly used for industrial-scale ultra-high molecular weight polyethylene (UHMWPE) fiber production, but orange terpenes, a byproduct of orange fruit production, present a bio-derived, sustainable alternative. In this work, fine UHMWPE fibers were spun using orange terpenes as the spin solvent, hot-drawn at a draw ratio of 5:1, investigated for their morphology, microstructure, and thermal and mechanical properties. The resulting fibers exhibited a flat, micro-ribbon cross-section, which is highly desirable for achieving high fiber volume fractions in UHMWPE-fiber reinforced composites. After drawing, the fibers possessed 4× greater breaking tenacity than any previously published studies on UHMWPE fibers spun using orange terpenes with a tenacity of 8.6 cN/dtex and tensile modulus of 229.2 cN/dtex. Microstructural analysis via differential scanning calorimetry and X-ray diffraction revealed that the hot drawing process significantly increased molecular orientation, but crystallinity decreased due to crystallite melting during drawing. Therefore, the mechanical properties of these fibers may be significantly improved with optimization of the fiber drawing process. As a work, this work establishes the strong potential of orange terpenes as an environmentally-friendly alternative solvent for UHMWPE gel spinning and sets a foundation for future parametric optimization of the spinning and drawing of these fibers.
Tribological studies at 25 C in a 50-percent-relative-humidity air atmosphere were conducted using hemispherically tipped 440 C HT (high temperature) stainless steel pins sliding against ultra-high-molecular-weight polyethylene (UHMWPE) disks. The results indicate that sliding speed, sliding distance, contact stress and specimen geometry can markedly affect friction, UHMWPE wear, UHMWPE transfer and the type of wear mechanisms that occur. Adhesion appears to be the predominant wear mechanism; but after long sliding distances at slow speeds, heavy ridges of transfer result which can induce fatigue-like wear on the UHMWPE disk wear track. In one instance, abrasive wear to the metallic pin was observed. This was caused by a hard particle embedded in the UHMWPE disk wear track.
The effect of molecular weight on 343 C thermo-oxidative stability (TOS), mechanical properties, and processability, of the first generation PMR polyimides was studied. Graphite fiber reinforced PMR-15, PMR-30, PMR-50, and PMR-75 composites (corresponding to formulated molecular weights of 1500, 3000, 5000, and 7500, respectively) were fabricated using a simulated autoclave process. The data reveals that while alternate autoclave cure schedules are required for the high molecular weight resins, low void laminates can be fabricated which have significantly improved TOS over PMR-15, with only a small sacrifice in mechanical properties.
The effect of molecular weight on 343 C thermo-oxidative stability (TOS), mechanical properties, and processability, of the first generation PMR polyimides was studied. Graphite fiber reinforced PMR-15, PMR-30, PMR-50, and PMR-75 composites (corresponding to formulated molecular weights of 1500, 3000, 5000, and 7500, respectively) were fabricated using a simulated autoclave process. The data reveal that while alternate autoclave cure schedules are required for the high molecular weight resins, low void laminates can be fabricated which have significantly improved TDS over PMR-15, with only a small sacrifice in mechanical properties.
Poly(pentylene adipate-co-terephthalate) (PPAT) is a promising biobased and biodegradable polymer that can replace polyethylene in flexible packaging films where biodegradability is desired. High-molecular-weight (100K–145 KDa) aliphatic–aromatic polyester PPAT was successfully synthesized, and the effects of reaction conditions on molecular weight were reported. PPAT polyesters were characterized for polymer compositions, number-average unit length, thermal transitions, and rheological properties. PPAT compression-molded films were characterized for crystallinity and tensile properties to correlate micro- and macroproperties. PPAT compression-molded films exhibited up to a 76% higher tensile modulus than compression-molded films from poly(butylene adipate-co-terephthalate) (PBAT), making PPAT films potentially comparable with compression-molded films from linear low-density polyethylene (LLDPE). Finally, PPAT is biodegradable in soil and freshwater environments with estimated 90% biodegradation times of 504–580 and 604–845 days, respectively, while PBAT takes 971 days in soil and 395 days in freshwater.