SEARCH · Search NASA
Results for “indium gallium oxide”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Vaporization of some group IIIA metal-metal oxide systems - Mass spectrometric identification of indium gallium oxides /InGaO and InGaO2/ and gallium aluminum oxide /GaAlO/
Studying vaporization of indium-gallium oxide, and gallium-aluminum oxide by Knudsen effusion mass spectroscopy
Experimental and theoretical evidence for hydrogen doping in polymer solution-processed indium gallium oxide
The field-effect electron mobility of aqueous solution-processed indium gallium oxide (IGO) thin-film transistors (TFTs) is significantly enhanced by polyvinyl alcohol (PVA) addition to the precursor solution, a >70-fold increase to 7.9 cm 2 /Vs. To understand the origin of this remarkable phenomenon, microstructure, electronic structure, and charge transport of IGO:PVA film are investigated by a battery of experimental and theoretical techniques, including In K-edge and Ga K-edge extended X-ray absorption fine structure (EXAFS); resonant soft X-ray scattering (R-SoXS); ultraviolet photoelectron spectroscopy (UPS); Fourier transform-infrared (FT-IR) spectroscopy; time-of-flight secondary-ion mass spectrometry (ToF-SIMS); composition-/processing-dependent TFT properties; high-resolution solid-state 1 H, 71 Ga, and 115 In NMR spectroscopy; and discrete Fourier transform (DFT) analysis with ab initio molecular dynamics (MD) liquid-quench simulations. The 71 Ga{ 1 H} rotational-echo double-resonance (REDOR) NMR and other data indicate that PVA achieves optimal H doping with a Ga···H distance of ~3.4 Å and conversion from six- to four-coordinate Ga, which together suppress deep trap defect localization. This reduces metal-oxide polyhedral distortion, thereby increasing the electron mobility. Finally, hydroxyl polymer doping thus offers a pathway for efficient H doping in green solvent-processed metal oxide films and the promise of high-performance, ultra-stable metal oxide semiconductor electronics with simple binary compositions.
17.2% Efficient CdSexTe1−x solar cell with (InxGa1−x)2O3 emitter on lightweight and flexible glass
High-efficiency, lightweight, and flexible solar cells are sought for a variety of applications particularly when high power density and flexible form factors are desired. Development of solar cells on flexible substrates may also offer production advantages in roll-to-roll or sheet-to-sheet processes. Here, we report device efficiencies of 17.2% and 14.6%, under AM1.5G and AM0 irradiances, respectively, for a flexible, lightweight, CdTe-based solar cell. To advance the efficiency relative to the highest previously reported AM1.5G value of 16.4%, we used an indium gallium oxide (IGO) emitter layer on a cadmium stannate (CTO) transparent conductor, which was deposited on 100-μm thick Corning® Willow® Glass. A sputtered CdSe layer was employed to incorporate Se into a CdTe absorber that was deposited by close-space sublimation, and CuSCN was used as a hole transport layer between the CdTe and the back metal electrode. The IGO and CTO layers remained intact during the high temperature film processing as seen in cross-sectional imaging and elemental mapping. This device configuration offers great promise for building-integrated photovoltaics, space applications, and higher rate manufacturing.
High stability of flexible perovskite transparent conductive oxide film via van der Waals heteroepitaxy
Transparent conducting oxides (TCOs), such as indium-tin oxide (ITO) and indium gallium zinc oxide (IGZO), are essential components in the design of flexible optoelectronic devices. However, it is still a challenge to prepare low-cost flexible transparent conductive film for achieving the flexible functionality together with high optical transparency and electrical conductivity. Herein, fluorphlogopite (mica) is selected as the bendable and transparent substrate for the fabrication of low-cost perovskite CaVO 3 TCO epitaxial film. Benefitting from thin mica substrate with high Young’s modulus of 200 GPa, flexible CaVO 3 TCO epitaxial film exhibits high mechanical stability in terms of electrical conductivity and optical transparency after bending up to 10 5 cycles. The change of resistance can reflect the bending curvature and strain state. Finally, our results provide a new pathway to design superior mechanical flexibility and stability CaVO 3 TCO films for application in flexible, light-weight, and portable smart optoelectronic devices.
Visualization of Mesoscopic Conductivity Fluctuations in Amorphous Semiconductor Thin-Film Transistors
Charge transport in amorphous semiconductors is considerably more complicated than the process in crystalline materials due to abundant localized states. In addition to device-scale characterization, spatially resolved measurements are important to unveiling electronic properties. Here, we report gigahertz conductivity mapping in amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors by microwave impedance microscopy (MIM), which probes conductivity without Schottky barrier’s influence. The difference between the dc and microwave conductivities reflects the efficacy of the injection barrier in an accumulation-mode transistor. The conductivity exhibits significant nanoscale inhomogeneity in the subthreshold regime, presumably due to trapping and release from localized states. The characteristic length scale of local fluctuations, as determined by the autocorrelation analysis, is about 200 nm. Using a random-barrier model, we can simulate the spatial variation of the potential landscape, which underlies the mesoscopic conductivity distribution. Furthermore, our work provides an intuitive way to understand the charge transport mechanism in amorphous semiconductors at the microscopic level.
Elastomeric Sensing of Pressure with Liquid Metal and Wireless Inductive Coupling
This project describes resistance-based soft sensors filled with liquid metal, which permit measurements of large strains (0 percent to 110 percent), associated with small forces of less than 30 Newtons. This work also demonstrates a methodology for wireless transfer of these strain measurements without connected electrodes. These sensors allow intermittent detection of pressure on soft membranes with low force. Adapting these sensors for passive wireless pressure sensing will eliminate the need for embedded batteries, and will allow the sensors to transmit pressure data through non-conductive materials including glass and acrylic. The absence of batteries allows us to embed these sensors into materials for long-term use because the sensors only use passive analog circuit elements. We found the oxidation of the liquid metal (eutectic gallium indium) plays a role in the repeatability of the soft sensors. We investigated how the oxidation layer affected the behavior of the sensor by encapsulating materials (silicone, fluorosilicone, and PVC) with varied permeabilities to oxygen. We measured the effects of mechanical loading on the oxidation layer and the effects of wireless inductive coupling on the oxidation layer. We concluded our research by investigating the effects of embedding self-resonant circuits into polydimethylsiloxane (PDMS). Efforts to design engineered systems with soft materials are a growing field with progress in soft robotics, epidermal electronics, and wearable electronics. In the field of soft robotics, PDMS-based grippers are capable of picking up delicate objects because their form-fitting properties allow them to conform to the shape of objects more easily than conventional robotic grippers. Epidermal devices also use PDMS as a substrate to hold electronic components such as radios, sensors, and power supply circuits. Additionally, PDMS-based soft sensors can monitor human motion with liquid metal embedded within micro-channels. Passive wireless sensors have applications in structural health monitoring and medical health monitoring. Doctors can take wireless blood pressure measurements inside arteries to monitor the progression of heart disease. Glaucoma patients can use this technology to monitor the pressure in their eyes to track the progression of the disease.
Deterministic modeling of hybrid nonlinear effects in epsilon-near-zero thin films
In nonlinear optics, significant effort is concentrated on improving the strength and efficiency of interactions; however, experimentally investigating nonlinear materials is a complex, time-consuming, and costly investment. Moreover, it is often challenging to isolate, study, and optimize material parameters in an experiment due to complexities in the growth process. Recently, epsilon-near-zero materials have received a great deal of attention as promising nonlinear optical materials, but like many up-and-coming materials, the ability to explore and optimize their properties has been challenging. Here, we establish a framework to rapidly evaluate the performance of nonlinear epsilon-near-zero materials for both inter- and intraband effects in silico, requiring only an energy-momentum (E-k) diagram, linear optical properties, and experimental conditions. Measured nonlinear reflection and transmission in gallium-doped zinc oxide films are compared to the numerical framework for both intra- and interband excitation to verify accuracy across wavelength and irradiance while two figures of merit (FoMs) are introduced to quickly evaluate the performance of films without a full numerical framework. This capability is used to predict the performance of highly doped gallium nitride, cadmium oxide, zinc oxide, and indium tin oxide films, and efficient intra- and interband operation conditions are identified. Through this numerical framework and the FoMs, the exploration of unstudied epsilon-near-zero materials is enabled without the need for a nonlinear experiment, thereby accelerating the search for more efficient nonlinear materials and excitation conditions.
The effect of process conditions on the performance of epitaxial InP solar cells
Indium phosphide solar cells have a higher resistance to electron irradiation than Si or GaAs cells of comparable junction depth. As a result, there is much interest in the use of this material for space applications. Cells of this material were made in bulk InP by a number of techniques, including ion implantation, direct diffusion in sealed ampoules, and by open tube diffusion. However, it is generally considered that the epitaxial approach will be superior to all of these techniques. The epitaxy of InP is considerably more difficult than that of gallium arsenide, for a number of reasons. Perhaps the most important is the fact that the native oxides of Indium are extremely difficult to remove, as compared to that of Gallium. In addition, thermal treatments for the desorption of these oxides often result in the formation of phosphorus vacancies and free indium on the surface. Thus, inadequate sample preparation before epitaxy, poor reactor cleaning procedures, or poor transition procedures between the growth of successive layers, all give rise to trap phenomena and to high interface recombination velocities. Moreover, the lifetime of the grown material is dominated by the occurrence of native defects, so that it is a strong function of growth parameters. These problems are of special interest to the fabrication of solar cells, where long life-time, combined with the absence of traps, is highly desirable. A study of this problem is described using a non-invasive diagnostic technique which was developed.
Article with buffer layer
An article, for example a solar cell, includes a first substrate having a first surface and a second surface. An underlayer is located over the second surface. A first conductive layer is located over the underlayer. An overlayer is located over the first conductive layer. A semiconductor layer is located over the conductive oxide layer. A second conductive layer is located over the semiconductor layer. The first conductive layer can include a conductive oxide and at least one dopant selected from the group consisting of tungsten, molybdenum, niobium, and/or fluorine. The overlayer can include a buffer layer having tin oxide and at least one of zinc, indium, gallium, and magnesium.
Gallium-doped zinc oxide: nonlinear reflection and transmission measurements and modeling in the ENZ region
Abstract Strong nonlinear materials have been sought after for decades for applications in telecommunications, sensing, and quantum optics. Gallium-doped zinc oxide is a II–VI transparent conducting oxide that shows promising nonlinearities similar to indium tin oxide and aluminum-doped zinc oxide for the telecommunications band. Here we explore its nonlinearities in the epsilon near zero (ENZ) region and show n 2,eff values on the order of 4.5 × 10 −3 cm 2 GW −1 for IR pumping on 200–300 nm thin films. Measuring nonlinear changes in transmission and reflection with a white light source probe in the near-IR while exciting in the near-IR provides data in both time and wavelength. Three films varying in thickness, optical loss, and ENZ crossover wavelength are numerically modeled and compared to experimental data showing agreement for both dispersion and temporal relaxation. In addition, we discuss optimal excitation and probing wavelengths occur around ENZ for thick films but are red-shifted for thin films where our model provides an additional degree of freedom to explore. Obtaining accurate nonlinear measurements is a difficult and time-consuming task where our method in this paper provides experimental and modeled data to the community for an ENZ material of interest.
Polymer-Stabilized Liquid Metal Nanoparticles as a Scalable Current Collector Engineering Approach Enabling Lithium Metal Anodes
Dendrites and dead lithium formation over prolonged cycling have long been challenges that hinder the safe implementation of metallic Li anodes. In this study, we employ polymer-stabilized liquid metal nanoparticles (LM-P NPs) of eutectic gallium indium (EGaIn) to create uniform Li nucleation sites enabling homogeneous lithium electrodeposition. Block copolymers of poly(ethylene oxide) and poly(acrylic acid) (PEO-b-PAA) were grafted onto the EGaIn surface, forming stabilized, well-dispersed NPs. Using a scalable spray coating approach, LM-P NPs were fabricated on copper current collectors, providing lithiophilic PEO sites and interactive carboxyl groups to guide Li deposition. The Li-EGaIn alloying process greatly reduced the Li + diffusion barrier, enabling fast Li transport through the coating layer, resulting in decreased nucleation overpotential. Therefore, about five times lower Li nucleation overpotential was obtained on the LM-P modified Cu with an optimal composition of the polymers than the bare Cu substrates. DFT computations was used to reveal the binding properties between the LM-P layer and Li. Due to the regulated Li plating/stripping process, as-obtained 30 μm Li anodes paired with LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM8 11 ) with a negative/positive electrode capacity (N/P) ratio ~ 10 exhibited stable cycling performance at 0.5C for over 250 cycles, with an average Coulombic efficiency of 99.55%. Ultrathin Li (1 μm) anodes with an N/P ratio ~ 0.6 were also demonstrated in Li|LiFePO 4 cells, which examined the stabilization of Li by LM-P NPs and monitored practical loadings of Li anodes that are close to anode-free systems.
IC Capacitors on Groups III-to-V Substrates
Oxides applied by a "spin-on" process have been used to fabricate capacitors on gallium arsenide and indium phosphide substrates: they might also be used with other compounds of elements in groups III to V of the periodic table. The III-to-V materials are attractive for integrated circuits because they offer responses potentially six times faster than silicon.
Liquid metal drop ejection
The aim of this project was to demonstrate the possibility of ejecting liquid metals using drop on demand printing technology. The plan was to make transducers for operation in the 100 MHz frequency range and to use these transducers to demonstrate the ability to eject drops of liquid metals such as gallium. Two transducers were made by indium bonding piezoelectric lithium niobate to quartz buffer rods. The lithium niobate plates were thinned by mechanical polishing to a thickness of 37 microns for operation at 100 MHz. Hemispherical lenses were polished in the opposite ends of the buffer rods. The lenses, which focus the sound waves in the liquid metal, had an F-number equals 1. A mechanical housing was made to hold the transducers and to allow precise control over the liquid level above the lens. We started by demonstrating the ability to eject drops of water on demand. The drops of water had a diameter of 15 microns which corresponds to the wavelength of the sound wave in the water. A videotape of this ejection was made. We then used a mixture of Gallium and Indium (used to lower the melting temperature of the Gallium) to demonstrate the ejection of liquid metal drops. This proved to be difficult because of the oxide skin which forms on the surface of the liquid. In some instances, we were able to eject metal drops, however, this was not consistent and reproducible. An experiment was set up at NASA-Lewis to stabilize the process of drop on demand liquid metal ejection. The object was to place the transducer and liquid metal in a vacuum station so that no oxide would form on the surface. We were successful in demonstrating that liquid metals could be ejected on demand and that this technology could be used for making sheet metal in space.
Detached Solidification of InSb on Earth
Detached solidification of lightly gallium-doped indium antimonide was achieved in the laboratory only when the ampoule was coated with hexagonal boron nitride and when the material appeared to be oxide-free. A furnace was constructed with the temperature increasing with height in order to minimize bouyancy-driven convection, so as to maximize transport of segregated dissolved gases into the gap between the growing solid and the ampoule wall. There appeared to be no difference in results with freezing rates of 5 mmh and 10 mm/h. Best results were obtained when the ampoule was backfilled with 20 kPa of Ar-10%H2 prior to sealing. The detached portions were depressed by several pm from adjacent attached regions, were rough, and sometimes had microfacets and steps.
Degradation Mechanism Due to Water Ingress Effect on the Top Contact of Cu(In,Ga)Se2 Solar Cells
The impact of moisture ingress on the surface of copper indium gallium diselenide (CIGS) solar cells was studied. While industry-scale modules are encapsulated in specialized polymers and glass, over time, the glass can break and the encapsulant can degrade. During such conditions, water can potentially degrade the interior layers and decrease performance. The first layer the water will come in contact with is the transparent conductive oxide (TCO) layer. To simulate the impact of this moisture ingress, complete devices were immersed in deionized water. To identify the potential sources of degradation, a common window layer for CIGS devices—a bilayer of intrinsic zinc oxide (i-ZnO) and conductive indium tin oxide (ITO)—was deposited. The thin films were then analyzed both pre and post water soaking. To determine the extent of ingress, dynamic secondary ion mass spectroscopy (SIMS) was performed on completed devices to analyze impurity diffusion (predominantly sodium and potassium) in the devices. The results were compared to device measurements, and indicated a degradation of device efficiency (mostly fill factor, contrary to previous studies), potentially due to a modification of the alkali profile.
A Molten Salt Electrochemical Process for the Preparation of Cost-Effective p-Block (Coating) Materials
Solar energy applications rely heavily on p-block elements and transition metals. Silicon is, by far, the most commonly used material in photovoltaic cells and accounts for about 85% of modules sold presently. Of late, thin film photovoltaic cells have gained momentum because of their higher efficiencies. Most of these thin film devices are made out of just five elements, namely, cadmium, tellurium, selenium, indium, gallium and copper. The present manuscript describes an elegant and inexpensive molten salt-based electrolytic process for fabricating a tellurium-coated metallic substrate. A three-electrode set up was employed to coat iridium with tellurium from a molten bath containing lithium chloride, lithium oxide and tellurium tetrachloride (LiCl-Li 2 O-TeCl 4 ) at 650 °C for a duration ranging from 30 to 120 min under a galvanostatic mode. The tellurium coating was observed to be thick, uniform, smooth and homogeneous. Additionally, the deposited tellurium did not chemically react with the iridium substrate to form intermetallic compounds, which is a good feature from the standpoint of the device’s performance characteristics. The present process, being generic in nature, shows the potential for the manufacture of both the coated substates and high-purity elements not just for tellurium but also for other p-block elements.