Search NASA⌕ Search

SEARCH · Search NASA

Results for “kinetic limitations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Delineating the kinetic limitations of Mn 2+/3+ redox in LiMn x Fe 1−x PO 4 cathodes for lithium-ion batteries

LiMn x Fe 1−x PO 4 (LMFP) cathodes offer higher energy density than LiFePO 4 due to a higher operating voltage. However, the kinetic limitations of the Mn 2+/3+ redox couple in LMFP restrict its practically achievable capacity and hinder the ability to achieve high energy density. While the shortcomings of Mn 2+/3+ redox are recognized, its behavior and the factors that impact it remain to be fully understood. We present here an in-depth kinetics study of LMFP by utilizing novel techniques, such as chronoamperometry and galvanostatic electrochemical impedance spectroscopy. Compared to moderate-Mn LMFP (40–60% Mn), high-Mn LMFP (80% Mn) experiences reduced capacity, poor rate capability, and heightened impedance during Mn 2+/3+ redox. The oxidation of Mn 2+ to Mn 3+ becomes more resistive during charge due to the formation of Jahn–Teller active Mn 3+ and the increasing charge-transfer insulating behavior of Mn x Fe 1−x PO 4 . However, the impedance associated with Mn 3+ to Mn 2+ reduction remains constant during discharge in the entire region. The protracted Mn2+ oxidation in high-Mn LMFP results in excessive impedance compared to that in moderate-Mn LMFP, even at low C-rates and high cycling temperatures. Despite the promise of high energy density, the extreme kinetic limitations inherent to high-Mn LMFP present a barrier.

25 ENERGY STORAGE↗
DOE OSTI2020

Kinetic Limitations in Single-Crystal High-Nickel Cathodes

High-nickel cathodes attract immense interest for use in lithium-ion batteries, to boost Li-storage capacity while reducing cost. For overcoming the intergranular-cracking issue in polycrystals, single-crystals are considered an appealing alternative, but aggravating concerns on compromising the electrochemical kinetics of electrodes. We report here a quantitative assessment of electrochemical reaction in single-crystal LiNi 0.8 Mn 0.1 Co 0.8 O 2 using operando hard X-ray microscopy/spectroscopy, revealing a strong dependence of redox kinetics on the state of charge (SOC) - being sluggish at low SOC while increasing rapidly as SOC increases both in the bulk electrode and individual particles. The observation is corroborated by transport measurements and finite-element simulation, indicating that the sluggish kinetics in single-crystals is governed by ionic transport at low SOC and may be alleviated through synergistic interaction with polycrystals integrated into a same electrode. Finally, with the elucidated mechanistic origin and alleviation solution of kinetic limitations in single-crystal high-Ni cathodes, this work constitutes a step forward in enabling their practical deployment.

25 ENERGY STORAGE↗
DOE OSTI2020

Intrinsic Kinetic Limitations in Substituted Lithium-Layered Transition-Metal Oxide Electrodes

Substituted Li-layered transition-metal oxide (LTMO) electrodes such as Li x Ni y Mn z Co 1-y-z O 2 (NMC) and Li x Ni y Co 1-y-z Al z O 2 (NCA) show reduced first cycle Coulombic efficiency (90-87% under standard cycling conditions) in comparison with the archetypal Li x CoO 2 (LCO; similar to 98% efficiency). Focusing on Li x Ni 0.8 Co 0.15 Al 0.0.5 O 2 as a model compound, we use operando synchrotron X-ray diffraction (XRD) and nuclear magnetic resonance (NMR) spectroscopy to demonstrate that the apparent first-cycle capacity loss is a kinetic effect linked to limited Li mobility at x > 0.88, with near full capacity recovered during a potentiostatic hold following the galvanostatic charge- discharge cycle. This kinetic capacity loss, unlike many capacity losses in LTMOs, is independent of the cutoff voltage during delithiation and it is a reversible process. The kinetic limitation manifests not only as the kinetic capacity loss during discharge but as a subtle bimodal compositional distribution early in charge and, also, a dramatic increase of the charge-discharge voltage hysteresis at x > 0.88. 7 Li NMR measurements indicate that the kinetic limitation reflects limited Li transport at x > 0.86. Electrochemical measurements on a wider range of LTMOs including Li x (Ni,Fe) y Co 1-y O 2 suggest that 5% substitution is sufficient to induce the kinetic limitation and that the effect is not limited to Ni substitution. In this paper, we outline how, in addition to a reduction in the number of Li vacancies and shrinkage of the Li-layer size, the intrinsic charge storage mechanism (two-phase vs solid-solution) and localization of charge give rise to additional kinetic barriers in NCA and nonmetallic LTMOs in general.

25 ENERGY STORAGE↗
DOE OSTI2021

Transport Modeling of Kinetically Limited Microscale Extraction Systems: Droplet and Supported Liquid Membrane Separations

Microfluidic droplet extraction devices can be used to efficiently measure solute phase transfer kinetics in liquid–liquid extraction systems. In this work, a droplet extraction apparatus was constructed using off-the-shelf and custom 3D printed parts for less than 110 USD. The interfacial kinetics of the transfer of Pu(IV) between an aqueous nitric acid phase and a 5 v/v% tridodecylamine (TDA) in toluene phase were characterized by determining the extent of Pu(IV) transfer between phases at different flow rates. Forward interfacial rate constants calculated from this data using an analytical model are 5.6 × 10 –3 mm s –1 under extraction (aqueous-to-organic solute transfer) conditions and 3.3 × 10 –3 mm s –1 under stripping (organic-to-aqueous solute transfer) conditions. The analytical model is valid when the rate of solute transfer across the interface between the two liquid phases has pseudo-first-order reversible reaction kinetics and is slow relative to the rate of solute transport to the interface. The change in the outlet concentration with residence time determined using the analytical model was compared with the results of a numerical model accounting for advection/diffusion to the interface in addition to kinetically limited interfacial solute transfer. These calculations revealed that for systems with forward interfacial rate constants greater than approximately 10 –2 mm s –1 , the analytical model must be supplemented with a numerical transport model accounting for an additional advection/diffusion mass transfer resistance. This threshold corresponds to a Damköhler number of one. The measured interfacial kinetic rate constants for Pu(IV)/TDA were used in a supported liquid membrane (SLM) numerical model, which showed that the Pu(IV) phase transfer kinetics are fast enough for use in a practical separation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Diffusion-Limited Kinetics in Reactive Systems

A proper representation of chemical kinetics is vital to understanding, modeling, and optimizing many important chemical processes. In liquid and surface phases, where diffusion is slow, the rate at which the reactants diffuse together limits the overall rate of many elementary reactions. Commonly, the textbook Smoluchowski theory is utilized to estimate effective rate coefficients in the liquid phase. On surfaces, modelers commonly resort to much more complex and expensive Kinetic Monte Carlo (KMC) simulations. Here, in this study, we extend the Smoluchowski model to allow the diffusing species to undergo chemical reactions and derive analytical formulas for the diffusion-limited rate coefficients for 3D, 2D, and 2D/3D interface cases. With these equations, we are able to demonstrate that when species react faster than they diffuse they can react orders of magnitude faster than predicted by Smoluchowski theory, through what we term “the reactive transport effect”. We validate the derived steady-state equations against particle Monte Carlo (PMC) simulations, KMC simulations, and non-steady-state solutions. Furthermore, using PMC and KMC simulations, we propose corrections that agree with all limits and the computed data for the 2D and 2D/3D interface steady-state equations, accounting for unique limitations in the associated derived equations. Additionally, we derive equations to handle couplings between diffusion-limited rate coefficients in reaction networks. We believe these equations should make it possible to run much more accurate mean-field simulations of liquids, surfaces, and liquid–surface interfaces accounting for diffusion limitations and the reactive transport effect.

Johnson, Matthew Sean↗
DOE OSTI2020

Calcium-Uranyl-Carbonato Species Kinetically Limit U(VI) Reduction by Fe(II) and Lead to U(V)-Bearing Ferrihydrite

Reaction conditions and mechanisms promoting or inhibiting U reduction exert a central control on U solubility and, therefore, U transport and its associated risks. Here, we vary and track common aqueous uranium species to show that a kinetic restriction inhibits homogeneous reduction of the calcium-uranyl-carbonato species (CaUO$_2$(CO$_3$)$_3$$^{2–}$ and Ca$_2$UO$_2$(CO$_3$)$_3$) by Fe(II)$_{(aq)}$, while ferrihydrite surface-catalyzed reduction of all aqueous uranyl by Fe(II) proceeds. Using U L$_3$ high energy resolution fluorescence detection (HERFD) X-ray absorption near edge structure (XANES) spectroscopy, U L$_3$ extended X-ray absorption fine structure (EXAFS) spectroscopy, and transmission electron microscopy (TEM), we also show that U(V) is generated and incorporated into ferrihydrite formed from homogeneous U(VI) reduction by Fe(II)(aq). Through elucidation of the mechanisms that inhibit reduction of the calcium-uranyl-carbonato species and promote stabilization of U(V), we advance our understanding of the controls on U solubility and thus improve prediction of U transport in surface and subsurface systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Kinetic Limitations in Single‐Crystal High‐Nickel Cathodes

Abstract High‐nickel cathodes attract immense interest for use in lithium‐ion batteries to boost Li‐storage capacity while reducing cost. For overcoming the intergranular‐cracking issue in polycrystals, single‐crystals are considered an appealing alternative, but aggravating concerns on compromising the ionic transport and kinetic properties. We report here a quantitative assessment of redox reaction in single‐crystal LiNi 0.8 Mn 0.1 Co 0.1 O 2 using operando hard X‐ray microscopy/spectroscopy, revealing a strong dependence of redox kinetics on the state of charge (SOC). Specifically, the redox is sluggish at low SOC but increases rapidly as SOC increases, both in bulk electrodes and individual particles. The observation is corroborated by transport measurements and finite‐element simulation, indicating that the sluggish kinetics in single‐crystals is governed by ionic transport at low SOC and may be alleviated through synergistic interaction with polycrystals integrated into a same electrode.

Ge, Mingyuan↗
DOE OSTI2022

Diffusion-Limited Kinetics of Isovalent Cation Exchange in III–V Nanocrystals Dispersed in Molten Salt Reaction Media

The goal of this work is to determine the kinetic factors that govern isovalent cation exchange in III–V colloidal quantum dots using molten salts as the solvent and cation source. We focus on the reactions of InP + GaI 3 → In 1 – x Ga x P and InAs + GaI 3 → In 1–x Ga x As to create technologically important ternary III–V phases. We find that the molten salt reaction medium causes the transformation of nearly spherical InP nanocrystals to tetrahedron-shaped In 1–x Ga x P nanocrystals. Furthermore, we determine that the activation energy for the cation exchange reaction is 0.9 eV for incorporation of Ga into InP and 1.2 eV for incorporation of Ga into InAs, both much lower than the measured values in bulk semiconductors. Next, we use powder XRD simulations to constrain our understanding of the structure of the In 1–x Ga x P nanocrystals. Together our results reveal several important features of molten salt-mediated cation exchange and provide guidance for future development of these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Undercooling minimization in ultrasound coupled DTA measurements of molten salts

Molten salts are ionic liquids that are used for the electrolytic pyroprocessing of metals and as heat transfer fluids in very high temperature processes. Recently, halide-based molten salt reactors (MSR) have gained momentum for high density and environmentally responsible electricity generation. The function of these reactors and their fuel cycle depend on a knowledge of the halide salt’s thermodynamic properties [1]. Therefore, high accuracy phase equilibria of MSR relevant base halide and actinide containing salts are needed. Modern thermal analysis of the phase transitions of halide salts is usually done during heating at relatively high scan rates with commercial devices. Normally such measurements are adequate for pure or pseudo-binary salts. However, as the number of components in the mixture increases, accurately resolving the liquidus becomes increasingly difficult. Reversing the scanning mode greatly increases the sensitivity of phase transition measurements but can decrease accuracy due to undercooling [2] — a common occurrence in molten halide systems [3]. This work presents the development of a differential thermal analysis (DTA) cell intended for use in radiological gloveboxes. Non-contact ultrasonic agitation of the halide salt is implemented to limit kinetic limitations on crystallization during cooling to minimize undercooling [4]. Measurements on halide salts are also presented to elucidate the effect of non-contact mixing on undercooling. Reference [1] S. Boyd and C. Taylor, “3 - Chemical fundamentals and applications of molten salts,” in Molten Salt Reactors and Thorium Energy, T. J. Dolan, Ed., Woodhead Publishing, 2017, pp. 29–91. doi: 10.1016/B978-0-08-101126-3.00003-8. [2] K. Nitsch, A. Cihlár, and M. Rodová, “Molten state and supercooling of lead halides,” J. Cryst. Growth, vol. 264, no. 1, pp. 492–498, Mar. 2004, doi: 10.1016/j.jcrysgro.2004.01.011. [3] L. Rycerz, “Practical remarks concerning phase diagrams determination on the basis of differential scanning calorimetry measurements,” J. Therm. Anal. Calorim., vol. 113, no. 1, pp. 231–238, Jul. 2013, doi: 10.1007/s10973-013-3097-0. [4] Md. H. Zahir, S. A. Mohamed, R. Saidur, and F. A. Al-Sulaiman, “Supercooling of phase-change materials and the techniques used to mitigate the phenomenon,” Appl. Energy, vol. 240, pp. 793–817, Apr. 2019, doi: 10.1016/j.apenergy.2019.02.045.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Solubility-limited depolymerization kinetics in the glycolysis of carbonyl-containing polymers

Chemical recycling of condensation polymers is often rationalized on the basis of the intrinsic reactivity of ester and carbonate functional groups. However, under heterogeneous conditions relevant to plastic waste processing and environmental degradation, bulk depolymerization rates often diverge from trends predicted by homogeneous chemistry. Here, we investigate how polymer–solvent compatibility, catalyst strength, and phase behavior govern the heterogeneous glycolysis of carbonyl-containing polymers. Using poly(ethylene terephthalate) (PET), glycol-modified PET (PETG), and bisphenol-A polycarbonate (PC) as model systems, we examine depolymerization kinetics at 180 °C with ethylene glycol and bisphenol A as diols under both amphoteric organosalt (TBD : MSA) and strong base (TBD) catalysis. Despite substantial differences in crystallinity and glycol uptake, PET and PETG depolymerize at comparable rates under organosalt catalysis, while PC depolymerizes significantly more slowly under identical conditions. Time-resolved molecular weight analysis and thermal characterization demonstrate that these rate differences do not arise from crystallinity, swelling, or inherent carbonyl reactivity, but instead reflect solubility-limited kinetics that constrain the transition from heterogeneous to homogeneous reaction regimes. When polymer solubility is low, depolymerization remains heterogeneous and slow; when solubility is enhanced—either through increased polymer–diol compatibility or stronger base catalysis—rapid homogeneous depolymerization is observed, reversing apparent reactivity trends. These results establish solubility and phase behavior as primary determinants of depolymerization kinetics in heterogeneous polymer recycling systems. By demonstrating how catalyst selection and solvent compatibility can expose or overcome solubility limitations, this work provides mechanistic insight to design more energy-efficient and selective chemical recycling processes. More broadly, these findings suggest that polymers with limited solvent or water compatibility may resist chemical degradation in the environment, favoring fragmentation and persistence as micro- and nanoplastics. Understanding solubility-controlled depolymerization offers a pathway toward more sustainable polymer design and end-of-life chemical recovery.

Watson-Sanders, Shelby [Department of Chemistry, U↗
DOE OSTI2025

Decoupling the capacity fade contributions in polymer electrolyte-based high-voltage solid-state batteries

Polymer electrolyte (PE)-based solid-state batteries (PE-SSBs) made with high-voltage cathodes are known to suffer from severe capacity fade, stemming primarily from the poor oxidative stability of most PEs under high-voltage cycling conditions. PEs also suffer from greater ion-transport limitations compared to liquid or solid electrolytes. However, often, these limitations are collectively stated to be responsible for the observed capacity fade, and it is challenging to decouple the contributions of different factors. Herein, a tunable cell fabrication platform was developed to systematically investigate and decouple the two primary capacity fade drivers (cell impedance growth and kinetic limitations), while keeping the other cell parameters constant. Three PE types with distinct transport characteristics were compared. By utilizing a voltage profile analysis method, the contribution of the cell's internal impedance growth was quantitatively decoupled from the kinetic limitations stemming from the high concentration gradient in the polymer catholyte and slow charge transfer reactions. We demonstrate that the high interfacial impedance did not necessarily correlate with the high capacity fade rate. Kinetic limitations that are not reflected by impedance measurements can play a dominant role in causing cumulative capacity decay.

Ock, Ji-young [Oak Ridge National Laboratory (ORNL↗
DOE OSTI2024

Kinetic-ballooning-limited pedestals in spherical tokamak plasmas

Abstract A theoretical model is presented that for the first time matches experimental measurements of the pedestal width-height Diallo scaling in the low-aspect-ratio high- β tokamak NSTX. Combining linear gyrokinetics with self-consistent pedestal equilibrium variation, kinetic-ballooning, rather than ideal-ballooning plasma instability, is shown to limit achievable confinement in spherical tokamak pedestals. Simulations are used to find the novel Gyrokinetic Critical Pedestal constraint, which determines the steepest pressure profile a pedestal can sustain subject to gyrokinetic instability. Gyrokinetic width-height scaling expressions for NSTX pedestals with varying density and temperature profiles are obtained. These scalings for STs depart significantly from that of conventional aspect ratio tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Knock Mitigation Effectiveness of EGR across the Pressure-Temperature Domain

Exhaust gas recirculation (EGR) has been shown to enable efficiency improvements in SI engines through multiple different mechanisms, including decreasing the knock propensity at high load, which allows higher compression ratio. While many of the benefits of EGR are applicable to both low and high power density engines, including reductions in pumping work and improved specific heat ratio, the knock benefits and corresponding compression ratio increases have been limited to low power density naturally aspirated engines primarily intended for hybrid vehicle architectures. An earlier study [1] indicated that there may be a kinetic limitation for the ability of EGR to mitigate knock under these conditions, but that study only considered a small number of conditions. In this investigation, we expand on that study while also providing data for model validation for the new light-duty combustion consortium from the U.S. Department of Energy: Partnership for Advancing Combustion Engines (PACE). In this investigation, the effectiveness of EGR to mitigate knock is studied with regards to the effect of engine speed (1,500 and 3,000 rpm), changing trajectory in the pressure-temperature domain by varying the intake manifold temperature (35, 60, and 90 deg C), and by considering the effect of minor species by studying the effect of untreated EGR vs. EGR that has been treated by an automotive three-way catalyst. Additionally, to increase the relevance of these data for future modeling studies, the performance of the full boiling range gasoline was compared relative to a surrogate formulation. The study found that the fuel surrogate performs well, confirmed the kinetic limitations of EGR to mitigate knock under boost, and showed improvements in EGR performance with catalyzed EGR.

42 ENGINEERING↗
DOE OSTI2020

Systems-level investigation of aqueous batteries for understanding the benefit of water-in-salt electrolyte by synchrotron nanoimaging

Water-in-salt (WIS) electrolytes provide a promising path toward aqueous battery systems with enlarged operating voltage windows for better safety and environmental sustainability. In this work, a new electrode couple, LiV 3 O 8 -LiMn 2 O 4 , for aqueous Li-ion batteries is investigated to understand the mechanism by which the WIS electrolyte improves the cycling stability at an extended voltage window. Operando synchrotron transmission x-ray microscopy on the LiMn 2 O 4 cathode reveals that the WIS electrolyte suppresses the mechanical damage to the electrode network and dissolution of the electrode particles, in addition to delaying the water decomposition process. Because the viscosity of WIS is notably higher, the reaction heterogeneity of the electrodes is quantified with x-ray absorption spectroscopic imaging, visualizing the kinetic limitations of the WIS electrolyte. This work furthers the mechanistic understanding of electrode–WIS electrolyte interactions and paves the way to explore the strategy to mitigate their possible kinetic limitations in three-dimensional architectures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Using in situ UO 2 bicrystal sintering to understand grain boundary dislocation nucleation kinetics and creep

Capillary evolution at bicrystal UO 2 grain boundaries is characterized using in situ transmission electron microscopy. The discontinuous nature of the densification process, both particle rotation and axial strain, along with the large activation stress for densification support a hypothesis that grain boundary strain in UO 2 follows nucleation rate limited kinetics at low to intermediate stresses, that is, less than ≈ 10 8 PA. Further, the temperature dependence of the average activation stress for sintering agrees well with analysis of bulk sintering data and creep data reported within the literature when analyzed in the context of a grain boundary dislocation nucleation rate limited kinetic model.

36 MATERIALS SCIENCE↗