Search NASA⌕ Search

SEARCH · Search NASA

Results for “non-inductive current drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Current ramp-up studies for NSTX-U in support of the development of non-inductive current ramp-up scenarios in STs

The Spherical Tokamak (ST) is a low-aspect-ratio tokamak projected to enable simultaneous operation at high normalized toroidal beta and high bootstrap current fraction. However, a compact ST reactor cannot be built with a full-sized solenoid. The remaining current required for sustained operation must be ramped up non-inductively. Sustained 100% non-inductive current drive at the MA level has not yet been demonstrated on an ST. Non-inductive current ramp-up is therefore a more challenging objective that the NSTX-U research program aims to address. In support of this development, free-boundary TRANSP simulations have been used to develop a current ramp-up scenario in which a significant fraction of the current is driven non-inductively by a combination of neutral-beam and bootstrap current drive. The resulting discharge has properties favorable for non-inductive current drive, such as a low normalized internal plasma inductance of approximately 0.45, a minimum safety factor exceeding 2, and a slightly reversed-shear q-profile. In these discharges, the plasma current ramps to 900 kA within 250 ms in an L-mode configuration, with varying electron density and density profiles. These discharges should be suitable for next-step NSTX-U experiments aimed at generating a robust L-mode fiducial scenario with low central solenoid flux consumption, which could be progressively improved as new NSTX-U experimental discharges are developed.

Raman, Roger [Univ. of Washington, Seattle, WA (Un↗
DOE OSTI2024

Optimization of the N ∥ Upshift in the DIII-D high field side lower hybrid current drive experiment

High field side lower hybrid current drive (LHCD) is one potential candidate for efficient non-inductive current drive in tokamak power plants, and the first test of this technology will occur on the DIII-D tokamak during the 2024 campaign. Previous LFS launch experiments operated in the multi-pass regime and relied on scrape-off layer interactions to close the spectral gap. In the DIII-D experiment, single-pass damping is achievable via an upshift in the parallel refractive index N ∥ caused by mode converting twice (slow → fast → slow). This mode conversion affects the ray trajectories and can lead to enhanced N ∥ upshift depending on where mode conversion occurs. Compared to multi-pass absorption experiments, the optimization of launched N ∥ and plasma parameters can be counter-intuitive: increased density may increase efficiency and smaller N ∥,launch tend to damp closer to the separatrix. A hard x-ray camera installed to measure the bremsstrahlung (50–250 keV) radiation from LHCD-generated fast electrons is capable of verifying the trends reporting in this paper through comparison to the ray-tracing/Fokker–Planck codes GENRAY/CQL3D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Polarimetry-Interferometry Diagnostic for Magnetic Field and Magnetic Fluctuation Measurements in High-Performance and Long-Pulse Tokamaks (Final Report)

In this grant, we executed a multi-year plan to develop an advanced Faraday-effect polarimeter-interferometer system to address both fluctuation and equilibrium diagnostic needs by providing a measurement of the plasma internal magnetic field fluctuations (including non-axisymmetric 3-D perturbations) and plasma vertical position. This diagnostic included both fast time response and low phase noise so that both the temporal dynamics of equilibrium quantities as well as high-frequency electromagnetic fluctuations could be measured simultaneously, adding new and unique measurement capabilities for the core of high-temperature plasmas. The combined polarimeter-interferometer diagnostic development was applied primarily to the tokamak magnetic configuration, focusing on high-performance regimes including H-mode, reversed shear advanced tokamak scenarios, and non-inductive current drive.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

WEST L-mode record long pulses guided by predictions using Integrated Modeling

A new record was set on the WEST Tokamak, designed to operate long duration plasmas in a tungsten (W) environment, with an injected energy of 1.15 GJ and a plasma duration 364s. Scenario development was supported by integrated modeling using the High Fidelity Plasma Simulator (HFPS), the European IMAS-coupled version of JETTO/JINTRAC, which integrates physics-driven modules into a unified framework. In particular, a reduced model for Lower-Hybrid heating and Current-Drive (LHCD) and the quasi-linear turbulent transport model TGLF are crucial for long pulses predictions up to the Last Closed Flux Surface (LCFS). Using this workflow, a 100 s reference discharge was modeled and plasma kinetic profiles and loop voltage were quantitatively well matched. In preparation for the recent long duration experiments, non-inductive current-drive actuators (I P , n e , P LHCD ) were varied to determine the operational domain going towards fully non-inductive discharges. In particular, decreasing the plasma current is shown to ease the access to such conditions, with a careful monitoring of (n e , P LHCD ) to avoid machine limitations. In addition, post-prediction experiments conducted within the investigated parameter range validated the predicted dependencies and were shown to be in quantitative agreement. Exploratory work on the use of ECCD for MHD stability purpose is also introduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Design considerations for optimizing the transient CHI injector on QUEST

Transient coaxial helicity injection (transient CHI) on the QUEST (Q-shu University Experiment with Steady-State ST) spherical tokamak (ST) has recently validated the floating biased electrode configuration for solenoid-free plasma startup. In support of a significant divertor upgrade on QUEST, the details of the transient CHI injector geometry on QUEST have been examined more closely using tokamak simulation code (TSC) simulations. QUEST uses a HIT-II-like (Helicity Injected Torus) injector configuration in which the injector region is comprised of coaxial injector electrodes located in the lower part of the machine. TSC simulations indicate high injector flux operation may benefit from an increased gap between the coaxial electrodes. This is the first study to examine the differences between an open and closed electrode configuration for solenoid-free plasma startup using transient CHI. Results show that both configurations can generate similar levels of closed flux, but the closed configuration may be easier to implement in some ST designs as a much smaller portion of the injector needs to be close to the injector flux coil. Results show that increasing the electrode gap width from the present 10.8 cm to about 15–20 cm would increase the closed flux fraction by about 40%. The results presented in this paper are generally applicable to the CHI design for other STs.

coaxial helicity injection↗
DOE OSTI2025

Optimization of simulated high-field side lower hybrid current drive coupling using machine learning predictions of scrape-off layer density

Lower hybrid current drive (LHCD) is a potential source of non-inductive off-axis current drive (CD) for tokamaks. Although LHCD has been successfully deployed on a number of tokamaks, it is highly sensitive to the scrape-off layer (SOL) conditions local to the LHCD launcher. Large gaps between the launcher and plasma core, SOL turbulence, or edge density perturbations due to edge-localized modes can hamper CD or cause large reflected power. These coupling issues in part motivated the installation of an LHCD launcher on the high-field side (HFS) of DIII-D. On the HFS, the SOL is less turbulent and more controllable compared to the low-field side. This quiescence may result in more predictable edge conditions and thus a more predictable CD. Here, in this work, HFS SOL reflectometry measurements are predicted from global plasma parameters using machine learning models. The SOL predictions coupled with the full-wave simulation of the LHCD launcher allow for the prediction of reflected power, directivity, and arcing risk before the discharge. Launcher performance is then optimized using multi-objective Bayesian optimization, finding the shot parameters that result in an optimal SOL density that maximizes CD while minimizing the risk of arcing. The predictions and optimizations of LHCD performance are then accelerated using a surrogate model of the full-wave LHCD simulation.

Bayesian optimization↗
DOE OSTI2023

Time dependent model for non-inductive ECH X-I current ramp-up for SHPD tokamak facility

Non-inductive (NI) plasma current start-up and ramp-up is an important research topic for spherical tokamak (ST) based reactors and fusion pilot plant (FPP). For a compact FPP, the OH flux availability is highly restricted due to its compact geometry. Efficient fundamental extraordinary mode (X-I) electron cyclotron heating (ECH) current start-up and ramp-up regime was identified for a reactor-like high toroidal magnetic field range which has more than a hundred times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. High current drive efficiency is possible due to the strong X-I fundamental ECH interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. Here, we extend the X-I electron cyclotron current drive (ECCD) investigation to a time dependent model to simulate the non-inductive current ramp-up to 10 MA for the Sustained High-Power Density (SHPD) facility. As the X-I ECCD driven current I EC rises, due to the back EMF driven negative current, the net plasma current Ip rises more slowly with the current resistive time scale. For tokamak confinement time (both L-mode and H-Mode) which tends to rise with I p , a positive feedback results and even with constant applied ECH power, T e0 , I EC , and I p can continue to rise to very high values. However, in a realistic situation, the T e0 rise should saturate due to a number of factors such as enhanced core radiation and increased power loss at high temperature. To simulate this effect, we adopt a maximum T e0 model which would limit the temperature rise to certain T e0 . With this model, we investigated the current ramp-up for various ECH power levels and the maximum T e0 of 15, 20, and 25 keV. We find that while the power required is reduced with increasing T e0 limit due to increased current drive efficiency, the time to reach 10 MA tends to go up due to the reduced plasma resistivity for the higher T e0 limit. We also find for a given Te0 limit, the time to reach 10 MA tends to be reduced by increasing the applied ECH power by over driving the current ramp-up where I EC is driven at significantly higher level than 10 MA. While the current ramp-up time may not be an issue for the steady-state reactor systems, if it is desirable to minimize the current ramp-up time, it is prudent to have a sufficient ECH power for current over-drive and have some T e0 limiting tools such as impurity seeding for enhanced radiation. In conclusion, a well-controlled NI ECH start-up also has a potential of improving the tokamak start-up reliability and avoid run-away electrons while the NI off-axis current drive could enhance MHD stability and plasma performance improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Operational space for lower hybrid heating scenarios in the full tungsten environment of WEST

In tungsten—W—Environment in Steady-state Tokamak (WEST), the lower hybrid current drive (LHCD) system is key for achieving long pulse operation by providing most of the non-inductive plasma current, as well as a crucial source of electron heating. Therefore, determining the operational space for its application is fundamental. In the present study, the LHCD operational space is deeply analyzed for 0.5 MA pulses. This space is bounded by three limits: (i) the ratio of the LHCD power over density must be above a threshold to compensate tungsten radiation with enough core heating, (ii) the line-averaged density must be high enough to allow good coupling of the hybrid wave with the plasma, and (iii) fast electron ripple losses must be below a limit to avoid reaching a thermal threshold on plasma-facing components. If the tungsten radiation peak or burn-through phase is not safely overcome, a maximum electron temperature of 1.5 keV is obtained, confinement is degraded, and magnetohydrodynamic activity is frequently triggered, potentially causing a disruption. From experimental measurements and interpretative simulations, we highlight the main mechanisms that prevent the plasma from heating up during LHCD power ramp-up. Three parameters play a major role: plasma density, tungsten concentration and LHCD power deposition. A strategy to overcome this limitation is found: a precise density ramp-up performed simultaneously with the increase in LHCD power. Additionally, we show that boronization greatly facilitates the burn-through of tungsten by lowering its content during the heating phase. Finally, taking into account the three constraints given above, the LHCD operational space is determined at power ramp-up and during constant heating phases.

lower hybrid heating and current drive↗
DOE OSTI2024

Transport and stability in sustained high q min , high β N discharges on DIII-D

Abstract To address the needs for a fusion pilot plan design, DIII-D/EAST joint experiments on DIII-D have demonstrated high normalized beta β N ∼ 4.2, toroidal beta β T ∼ 3.3% with q min > 2, q 95 ⩽ 8 sustained for more than six energy confinement times in high poloidal beta regime. The excellent energy confinement quality ( H 98y2 ∼ 1.8) is achieved with an internal transport barrier at high line-averaged Greenwald density fraction f Gr > 0.9. The trapped gyro-Landau fluid (TGLF) modeling of the transport characteristics shows that the beam-driven rotation does not play an important role in the high confinement quality. The modeling also captures very well several transport features, giving us confidence in using integrated modeling to project these experimental results to future machines. The high-performance phase is terminated by fast-growing modes triggered near the n = 1 ideal-wall kink stability limit. New radio frequency (RF) capabilities for off-axis current drive could remove the residual ohmic current to achieve a fully non-inductive state, and improve the mode–wall coupling to increase the ideal-wall β N limit, enabling sustainment of the fully non-inductive high performance plasma in stationary conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Auxiliary heating and current drive physics for the ST-E1 fusion power plant

This work describes the physics basis for the proposed auxiliary heating and current drive system on the ST-E1 fusion power plant. The ST-E1 flattop plasma considered here is fully non-inductive with a bootstrap fraction of 0.9 and the remaining current driven by EC waves. Using the recently published physics-based optimization method for EC launchers (Lopez et al 2025 Plasma Phys. Control. Fusion 67 055012), we show that the target flattop ECCD can be achieved with a net efficiency of 52 kA MW −1 using fundamental O-mode (O1) with frequency range 160–200 GHz launched from the low-field side top half of the vacuum vessel (LFS top-launch). From considering two candidate rampup scenarios, we conclude that LFS top-launch O1 ECCD can be equally effective during the early stages of plasma operation, although poloidal steering might be needed. X-mode waves injected from the LFS midplane are also shown to be effective for rampup even when T e < 1 keV. We also present modeling results for the pre-conceptual design of an ICRH system proposed for ST-E1. Using TORIC, we find that an ICRH system aiming for 42–48 MHz and toroidal mode number n φ ~ 10 robustly achieves dominant ion damping via Helium-3 minority heating transitioning to second-harmonic Tritium heating. We then show that such waves can be efficiently generated by a 5-strap traveling-wave antenna (TWA) using the Petra-M code. The TWA has a 40–45 MHz passband within which ~60% of the power entering the TWA is coupled to the plasma with the remaining ~40% of the power being transmitted through the TWA and possibly recirculated; the power reflected back into the transmission lines is negligible. This passband structure persists even when the evanescent distance is increased by a factor of two, or when the magnetic-field angle is increased by 30°, demonstrating inherent load resilience that will be crucial for effective ICRH on ST-E1.

electron cyclotron↗
DOE OSTI2025

Experimental progress and future plans on spherical tokamak, QUEST

QUEST (Q-shu university experiment with steady state spherical tokamak) aims at effective plasma current start-up and stable maintenance of plasma discharge. To solve the inherent problems in a spherical tokamak (ST) arising from insufficient space for placing the inductive center solenoid, electron cyclotron current drive (ECCD) and transient coaxial helicity injection (T-CHI) are implemented as a non-inductive plasma start-up method in QUEST. Efficient ECCD assisted by energetic electrons could be achieved. By combining control of the wave injection angle and application of a negative toroidal electric field, the bulk electron temperature could be raised up to 1 keV due to selective wave power absorption in the bulk electrons. The plasma current of over 50 kA contained within the closed flux surface could be obtained with a floating single biased electrode placed on lower divertor plates for T-CHI. Long-pulse operations on QUEST are impeded frequently due to wall saturation and subsequent density runaway caused by fuel particle imbalance. Since 2014, a unique tool called the ‘hot wall’ has been implemented to overcome the imbalance. The hot wall has a capability to regulate its surface temperature using a heater and two water cooling channels. With the help of the hot wall, 6 h discharges were obtained in 2020. Cooling down of the surface of the hot wall was significantly effective in recovering the wall pumping and was useful to extend the pulse duration. Augmentation of the toroidal magnetic field, B T up to 0.5 T from 0.25 T and a continuous wave (CW) gyrotron of 28 GHz are planned for QUEST in the near future. As raising B T provides a fundamental resonance of electron cyclotron waves (ECWs) with 28 GHz, more effective plasma current start-up and heating will be performed. Long-pulse operations with higher plasma parameters are expected.

QUEST↗
DOE OSTI2024

Efficient ECCD non-inductive plasma current start-up, ramp-up, and sustainment for an ST fusion reactor

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ~10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW –1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Long-pulse high-performance H-mode plasmas achieved on EAST

A record duration of a 310 s H-mode plasma (H 98y2 ~ 1.3, n e /n GW ~ 0.7, f BS > 50%) has been recently achieved on experimental advanced superconducting tokamak (EAST) with metal walls, exploiting the device's improved long-pulse capabilities. The experiment demonstrates good control of tungsten concentration, core/edge MHD stability, and particle and heat exhaust with an ITER-like tungsten divertor and zero injected torque, establishing a milestone on the path to steady-state long-pulse high-performance scenarios in support of ITER and CFETR. Important synergistic effects are leveraged toward this result, which relies purely on radio frequency (RF) powers for heating and current drive (H&CD). On-axis electron cyclotron heating enhances the H&CD efficiency from lower hybrid wave injection, increasing confinement quality and enabling fully non-inductive operation at high density (n e /n GW ~ 70%) and high poloidal beta (β P ~ 2.5). A small-amplitude grassy edge localized mode regime facilitates the RF power coupling to the H-mode edge and reduces divertor sputtering/erosion. The high energy confinement quality (H 98y2 ~ 1.3) is achieved with the experimental and simulated results pointing to the strong effect of Shafranov shift on turbulence. Transport analysis suggests that trapped electron modes dominate in the core region during the record discharge. The detailed physics processes (RF synergy, core-edge integration, confinement properties, etc.) of the steady-state operation will be illustrated in the content. In the future, EAST will aim at accessing more relevant dimensionless parameters to develop long-pulse high-performance plasma toward ITER and CFETR steady-state advanced operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Overview of recent results from the ST40 compact high-field spherical tokamak

ST40 is a compact, high-field ($B_{\mathrm{T0}}\unicode{x2A7D} 2.1\,\,\,\textrm{T}$) spherical tokamak (ST) with a mission to expand the physics and technology basis for the ST route to commercial fusion. The ST40 research programme covers confinement and stability; solenoid-free start-up; high-performance operating scenarios; and plasma exhaust. In 2022, ST40 obtained central deuterium ion temperatures of $9.6 \pm 0.4\ \textrm{keV}$, demonstrating for the first time that pilot plant relevant ion temperatures can be reached in a compact, high-field ST. Analysis of these high-ion temperature plasmas is presented, including a summary of confinement, transport and microstability characteristics, and energetic particle instabilities. Recent scenario development activities have focused on establishing diverted H-mode plasmas across a range of toroidal fields and plasma currents, along with scenarios with high non-inductive current fractions. In future operations, beginning in 2025, a 1 MW dual frequency (104/137 GHz) electron cyclotron (EC) system will be installed to enable the study of EC and electron Bernstein wave plasma start-up and current drive. Predictive modelling of the potential performance of these systems is presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Nonlinear control of the minimum safety factor in tokamaks by optimal allocation of spatially moving electron cyclotron current drive

The minimum value of the safety factor profile is related to the magnetohydrodynamic (MHD) stability of the plasma confined in a tokamak. Therefore, active control of the minimum safety factor may mitigate MHD instabilities that can degrade or even terminate plasma confinement. Typically, in most tokamak scenarios, the minimum safety factor evolves spatially with time, i.e., the location at which the safety factor achieves the minimum value changes with time. In addition to the inherent nonlinearities in the minimum safety factor evolution, its spatial variation makes the control design challenging. In particular, complexity in control design may arise from the need for time-dependent nonlinear models that account for spatial variation of the minimum safety factor. Furthermore, the minimum safety factor may drift to locations where the actuator authority is low. The problem of minimum safety factor control with target location tracking and moving electron cyclotron current drive (ECCD) is addressed in this work. A nonlinear time-dependent model that incorporates the spatial variation of the minimum safety factor is presented. A nonlinear controller based on optimal feedback linearization is developed to track a target minimum safety factor. The proposed controller treats the ECCD position as a controllable variable. In other words, the controller prescribes the ECCD position (in addition to the non-inductive powers) in real time based on an optimal criterion that is defined a priori. This work also presents the steps necessary to integrate the minimum safety factor controller with a total energy controller to achieve multiple control objectives simultaneously. In conclusion, the proposed integrated control algorithm is tested using nonlinear simulations in the Control Oriented Transport SIMulator (COTSIM) for a DIII-D tokamak scenario.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Physics basis for the reference flat-top plasma scenario in the ST–E1 fusion power plant

As part of the U.S. Department of Energy’s Milestone-Based Fusion Energy Development Program, Tokamak Energy has completed the pre-concept design of the ST–E1 fusion power plant. ST–E1 is envisaged to operate in two phases: a pilot plant phase, targeting sustained net power production of 300 - 500 MWe for a duration >1 hr, followed by a commercial power plant phase targeting steady-state operations and a normalised overnight capital cost of ⩽12 000 $\$$/kWe. The design process adopted was highly iterative, integrating all major plant systems and progressing in a phased fidelity approach. At the pre-conceptual stage, the emphasis has been on exploring the design space, identifying the main system-level trade-offs, and making the key decisions that define the overall plant concept, rather than optimising a single operating point. This paper, part of a focused collection detailing the ST–E1 pre-concept design, addresses the development of a series of reference flat-top plasma operating points for the pilot plant phase. A modelling workflow was established to develop and assess candidate plasma design points and explore key dependencies. The workflow includes integrated core plasma modelling, magnetohydrodynamic (MHD) stability assessment, equilibrium generation, scrape-off-layer and exhaust modelling, heating & current drive design and optimisation, and turbulent transport modelling. Using this framework, the impact of several key parameters on the flat-top operating space was investigated, including the density limit, core radiation fraction and divertor power loading, level of external heating and curent drive power and assumed pedestal characteristics. The MHD stability, controllability and micro-stability characteristics of these plasmas were also analysed. These investigations informed the definition of a set of fully non-inductive, flat-top reference operating points that satisfy the high-level ST–E1 mission, including a low and high density case, a case that is stable to resistive wall modes and a case with reduced divertor power loading.

ST–E1↗
DOE OSTI2025

Modeling resistive-inductive evolution of currents in Wendelstein 7-X

This research investigates the temporal evolution of the toroidal plasma current in the Wendelstein 7-X (W7-X) stellarator under different heating, fueling, and current drive scenarios. The THRIFT code has been modernized and its predictions of the evolution of the toroidal current have been compared against experimentally measured currents in W7-X. Good agreement is found with respect to the characteristic timescale between experimentally measured and simulated toroidal currents. The total bootstrap current is under-predicted owing to the applicability of the BOOTSJ model for the plasma collisionalities in question. Edge plasma resistivity is found to play an important role in the asymptotic behavior of the evolution of the current, indicating a possible limitation of the minimum plasma temperature when applying this model. Simulations of ECCD and heating power steps show THRIFT is capable of capturing the dynamical evolution of the current in response to changes in current sources. Future uses of THRIFT include validating and benchmarking other non-inductive current models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Evaluation of DIII-D plasmas for Future Measurements of the Driven Current Density in the DIII-D High Field Side Lower Hybrid Experiment

High field side (HFS) lower hybrid current drive (LHCD) is a promising method for efficiently driving off-axis current in steady state tokamak power plants. The first test of this technology is underway at the DIII-D tokamak. The initial physics goal is to measure the LH-driven current density profile in order to validate the ray-tracing/Fokker-Plank codes GENRAY/CQL3D and gain confidence in their ability to predict LH deposition in future DIII-D experiments and fusion power plants. DIII-D’s motional Stark effect (MSE) diagnostic will be used to constrain the magnetic equilibrium reconstructions. From these reconstructions, the ohmic, bootstrap, and driven non-inductive components of the current density profile can be extracted. Several recent DIII-D plasmas have been identified in which GENRAY/CQL3D predict measurable amounts of current with only 100 kW of coupled power.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗